Want to make $20 thru paypal? help me get my Tilt out of the bootloader screen!
first off, im not new here; i lurked, learned, and flashed a few roms before i really posted much of anything.
my Tilts' screen was cracked a few days back, im headed to Greece in 2 days, so i went and bought a new Tilt to replace it until the replacement screen part gets here from Hong Kong.
The new Tilt came with WM6.1 installed, first thing i did is CID unlock it with HardSPL. i kept getting the white screen, but managed to bypass it, and flashed the RynCppr V4 on it with only the aforementioned white screen issue. I also have Ruu_Signed_Duttys_WM6.1_Official_5.2.19209_1_58_16_27 [FIX] ROM, but that would not install, i kept getting comm errors (ie the installation would never get past 0%).
I would like to run Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06[CubeV2] as i've played around with it on a buddy's Tilt, but it too wont install past 0%; i NEVER had these problems at ALL on my old Tilt (WM6.0), it seems to be linked to the SPL, and hardSPL does not seem to be allowing me to flash anything but the RynCppr V4 ROM; im getting extremely torqued about this, please, any assistance would be appreciated.
Take a look at this post (it's in the Stickies). If you have the white screen then you need to use JumpSPL. Use 1.93.
http://forum.xda-developers.com/showthread.php?t=354061
Good luck.
ecltech said:
Take a look at this post (it's in the Stickies). If you have the white screen then you need to use JumpSPL. Use 1.93.
http://forum.xda-developers.com/showthread.php?t=354061
Good luck.
Click to expand...
Click to collapse
thanks, thats precisely how i bypassed the first white screen errors; the problem here is i can get into the bootloader, but it wont transfer and install the new ROM. i have to jump the SPL every time i want to attempt to flash a ROM. im down to about 4 hrs left of trying before i have to give up and get going lol.
You can't install a ROM using JumpSPL. Just HardSPL the device once you have run JumpSPL as per the instructions in the post and once it's HardSPLed you can install any ROM.
RynCppr worked because it's an AT&T base ROM.
use jumpspl to flash hardspl, then you can flash roms the normal way.
do not use jumpspl to flash a rom.
XtreMe_G said:
use jumpspl to flash hardspl, then you can flash roms the normal way.
do not use jumpspl to flash a rom.
Click to expand...
Click to collapse
it wont let me install HardSPL even with JumpSPL. now its stuck in the bootloader. im trying to get the OEM or the Cppr ROMS...
slade8525,
make sure you follow these steps exactly:
1a. download the 5 attached files
1b. pull out the battery and reinsert it (this step *is* important)
1c. connect your PC to phone with a USB cable
2. REMOVE SIM and SD CARDS !!
3. copy JumpSPL1.56-KAIS.exe to your device and run it (make sure the USB cable is still connected). If you still get a white screen then reset your device and now try JumpSPL1.93-KAIS.exe
4. after a few seconds "USB" appears on the phone display
5. unplug and replug the usb cable
6. deselect "Allow USB connections" in Activesync connection settings
7. now flash hardSPL (run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC)
Are you trying 1.93 or 1.56? I never had luck with 1.56 so try 1.93 if you're not.
Very important you do the steps as listed above. Any shortcuts and no go. When I was doing this on a Tilt I replaced, I kept forgetting to disable the USB connection from Active Sync and also unplug/replug the USB cable.
if anyone can walk me through getting it the HELL out of the bootloader or direct me to the correct ROM that WILL flash correctly, i'd be willing to paypal $20 ASAP.
ecltech said:
slade8525,
make sure you follow these steps exactly:
1a. download the 5 attached files
1b. pull out the battery and reinsert it (this step *is* important)
1c. connect your PC to phone with a USB cable
2. REMOVE SIM and SD CARDS !!
3. copy JumpSPL1.56-KAIS.exe to your device and run it (make sure the USB cable is still connected). If you still get a white screen then reset your device and now try JumpSPL1.93-KAIS.exe
4. after a few seconds "USB" appears on the phone display
5. unplug and replug the usb cable
6. deselect "Allow USB connections" in Activesync connection settings
7. now flash hardSPL (run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC)
Are you trying 1.93 or 1.56? I never had luck with 1.56 so try 1.93 if you're not.
Very important you do the steps as listed above. Any shortcuts and no go. When I was doing this on a Tilt I replaced, I kept forgetting to disable the USB connection from Active Sync and also unplug/replug the USB cable.
Click to expand...
Click to collapse
well, i tried that method several times now, unfortunately im now stuck in the bootloader. here is precisely what the red/green/blue/white bootloader interface says...
top left RUUNBH
top right
KAIS1*0
SPL-1.93.0000
CPLD-8
bottom (in the white band) USB (if connected to PC) Serial (if not connected to PC)
i REALLY need this damn thing operational. flashing my 'older' launch Tilt was a piece of cake. if i try to flash HardSPL (through the PC ) it gets me to the command prompt where you hit Enter, i hit it, and nothing happens. i try to flash ANY ROM and it wont get past 0% and encounters a connection error.
Flash the WM6 factory ATT Rom (do all this crap while in wm6.0)
Go to bootloader mode & confirm HardSPL....if not there, HardSPL
Once done....do the security unlock (may as well do it with wm6.0)
Go to bootloader mode and confirm Security Unlock...if confirmed ***flash back the original Radio***
You should now be HardSPL'd and Security unlocked
Flash a wm6.1 Rom w/Radio (this will skip a flash)
You now have to flash one of the JumpSPL's....since you have a new device, flash the latest
Flash the HardSPL of your choice
Go to bootloader mode to confirm
DONE
Note: Have all you info available and files ready
When flashing SPL's, make sure your SD card is removed
Just went thru this just to get Security Unlocked because security unlock c/n be done with a 3.28 or 3.26 SPL and early on...HardSPL had to be done in wm6.0 and I had issues upgrading the SPL to 3.29 in wm6.0...that's why I say flash to 6.1 (say that twice)
you have bricked your device, for someone who claims to not be new, you should know better and flash hardspl before anything else.
if you want you can try this or just contact gsleon3
XtreMe_G said:
you have bricked your device, for someone who claims to not be new, you should know better and flash hardspl before anything else.
if you want you can try this or just contact gsleon3
Click to expand...
Click to collapse
actually ECLtech is walking me through it right now.
Related
Hey all, first post long time reader.
Please dont flame me, i have tried to search for the answer but seem to be going nowhere.
Is anybody getting the Error [262] while using KaiserCustomRUU.exe? I just flashed Dutty's DualTouch v4, that worked great! Now i am trying to flash the radio, i have heard good things about 1.27.12.17. It will not flash, I have followed the instructions over and over again. It gets to the point where it shows the completion bar, it gets stuck with 0%. I follow the instructions, pull the battery out and try again, no luck. I have noticed that during the process active sync goes from green to grey. (I think this is supposed to happen) But the odd thing is that the "Local Area Connection" (for the phone) in Windows XP Network Connection disappears. I am guessing this is my problem. Does anybody know what causes the phone to disconnect from the computer? Or am i doing something obviously wrong.
Any help is appreciated.
also - after it locks up at th 0% screen, and after i receive the error 262, i then unplug the phone from the computer. when i do this, windows makes the sound of a USB device getting unplugged. so does that mean i really didnt loose connection, and the error 262 is due to something else?
Did you use Hard SPL Before flashing.Is a must to not brick your phone.
http://forum.xda-developers.com/showthread.php?t=334679
Read carefully and will be OK.
Yes i have used HardSPL. I have already flashed with Duty's DualTouch ROM, and it WORKS. It was really easy and painless. For some reason I can not get the radio to flash. From my understanding, HardSPL only needs to be done once. That changes the bootloader, i think? Either way, I already did the HardSPL, flashed the ROM, just want to change the radio now. As the instructions said, this can be done after I flash the ROM using CustomRUU. Any thoughts?
I am going to go ahead and try to flash a custom flash screen. Will post back results
I tried using the CustomRUU to flash Kaiser with new splash screen, but no luck. Same error as before. Good news is that the phone still works!
If you are shure about Hard SPL (you can check again if is rited OLIPOF) "Hold Camera + Power buttons together and reset with stylus"-to enter in Bootloader and check again.
If is correct I sugest to reflash with original HTC Rom (wich include radio ) and after that start again with HardSPL --- Radio --- ROM upgarde
For hard spl http://forum.xda-developers.com/showthread.php?t=334679
For original and other info http://forum.xda-developers.com/showthread.php?t=332246
and one of the best link for reverting http://forum.xda-developers.com/showthread.php?t=335568
Good luck !!!
ok so i go into bootloader, and i get
KAIS1*0
SPL-1.56.0000
CPLD-8
i had followed the insructions from this thread - http://forum.xda-developers.com/showthread.php?t=334679
- HTC Kaiser Hard-SPL v1 - CID Unlock & Flash any ROM to your device (4 free)
looks like i did something wrong? it does not say OLIPOF
any ideas? can i just do it all over again, and be safe?
thanks for your help.
You had some luck to flash cooked ROM without Hard SPL.Be more carefuly and read .Those guys work for us to be protecyed from breaking our phones
yes but read carefuly:
Please make sure ActiveSync is enabled (GREEN icon in systray)
and hit ENTER to start...
Kaiser JumpSPL is running on your device, please check your device
screen and follow the steps until you see the tri-color screen.
When done hit ENTER to continue...
Device screen should be now TRI-COLOR and show "USB"
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
ActiveSync icon should become gray after that.
When done hit ENTER to continue...
Phone screen should now be tri-color and the activesync icon gray
if not, the loading process has failed and you'll have to repeat it again.
If all was OK hit ENTER and the standard "PDA Phone ROM Update Utility"
window will start, allowing you to flash HardSPL on your device.
Hit CTRL+C to Cancel or ENTER to continue...
Follow the steps on the wizard to flash HardSPL, when finished your
device will reboot. It should last no more than 1 minute.
- Launching RUU, please wait...
Process is finished, congratulations!
I see what you are saying. So some how I managed to just flash on the JumpSPL, and bypass the last steps of flashing HardSPL?
So now I should follow http://forum.xda-developers.com/showthread.php?t=354061
do step - "if you want to flash a hardSPL then run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC"
or do you suggest i just try to install HardSPL over again.
damn i suck, i thought i was being careful.
try Hard SPL but follow the instruction and don't hurry wait for every message from that window
That thread is just in case your phone don't enter in bootloader
will do, thanks for your help!
its definetly not my first day using a computer, flashing ROMs, etc. damn i feel like a complete newb
hey it worked. thanks for your help. if you are ever in chicago, PM me. i owe you a few beers.
No problem .Glad can help.
OK
I've always had troubles flashing radios for some reason, I've managed to just not do it but now with Duttys 6.1 out I really need some help
- I've flashed Duttys latest successfully
- I've flashed HardSPL
- But whenever I flash the radio (1.64.08.21) I get a connection error at 99%!!
Now I can still get into the phone using mtty and the boot command.
Am I doing something stupid -- Any help gratefully received!
Alex
ps - I have a UK o2 XDA Stellar
I'm a newbie been here with a AT&T Tilt less than a week and I promise I'm reading, but I'm having the exact same problem. Flashed Duttys dual V4 as my first try last Tuesday without a problem and of course be a crazy new guy I wanted his newest work. So I flashed Duttys 6.1 today and I guess I just can't figure out how to flash radios, because I've tried 2 now and both error out at 99% and I too have to use mtty to get back into the phone. I'll keep reading, but if someone could tell us new guys what the heck we are doing wrong that would be great.
PS I'm glad to be here and this looks like a lot on fun thanks for having me and look forward to helping out someday.
JMan
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
First, are you using a 6.0 rom or a 6.1 rom? If you are using a 6.0 rom you cannot flash any of the 6.1 radios and vice versa. Also, if you have hardspl installed, why would you need to use jumpspl. I have never used jumpspl and I promise I have flashed 50+ times counting, roms, radios and splash screens.
I believe that was my problem, I was never able to get Hard-spl installed and I was using jumpspl to install the 2 roms that I have installed since I got my tilt a week ago. The method I used above allowed me to get hard-spl installed and then I was able to install the radio rom. I am using Duttys WM6.1 rom.
JMan I want your babies!!!
Ok I had actually done everything upto the final step (holding the camera button after a soft reset) but that made it possible to flash the radio just as you described.
So many thanks for sharing your solution!!
Alex
jmandss said:
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
Click to expand...
Click to collapse
You are the STAR! Trillions of thanks. Solve my problem!!!
I love it when when the new guy can help out! Glad it worked guys, and thanks to all the old pros around here for allowing us to read so we can try and help ourselves out.
Take care,
JMan
I think I have fallen in love with this thread. This is truly nice to see guys. Keep up the great work.
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
please help me
I don't want to miss mi tytn
pedro_se_rooot said:
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
Click to expand...
Click to collapse
You need to use MTTY to get things going for you again, here is the thread to get mtty:
http://forum.xda-developers.com/showthread.php?t=371154&highlight=mtty
Search around and see if you can find the step by step to use it, might even be a how to text file in the zip file not sure. This should get you back on your way.
Can someone locate the step by step to use mtty for this man and put it in this post?
Have a good one,
JMan
Not a good day for the Wolfpack, Damn Tarheels!!
first of all thank you for everyone on this forum for their remarkable work.
ok first i might be a noob but i have read every single thread and still i cannot get it straight. i'm not a electonic user freindly
i need to get rid of the freeze that happens every 3-5 seconds and i read that i have to flasg spl, but which one? (attaching the files needed would be great as i don't know their name and they are similar so just tell me the name of the file)
ok, first of all i have no idea which sl i have as i did the SPL the first time using a file.exe which i cannot even remeber the name , so u tell me pls
when i go to boot loader mode i see this:
KAIS130 MFG
SPL1.0.olipof
CPLD-8
now i have death v3 and radio 1.65.20.29
just need a step by step and which file to use first and what to do in it , i have no idea what OEM means if you are gonna say install OEM
thank you so much, and i know it has been asked a lot but am a bit disabled so don't mind my idiocey
any help would be much apreciated.
P.S. i already read the fix freeze thread and i got lost
ahassouna said:
first of all thank you for everyone on this forum for their remarkable work.
ok first i might be a noob but i have read every single thread and still i cannot get it straight. i'm not a electonic user freindly ...
Click to expand...
Click to collapse
If you have read this thread completely and still don't understand what to do, then you probably shouldn't mess with it.
Honestly...this is the nicest response you are going to get
bengalih said:
If you have read this thread completely and still don't understand what to do, then you probably shouldn't mess with it.
Honestly...this is the nicest response you are going to get
Click to expand...
Click to collapse
hence why i started with a thank you cause i know someone will eventually say something really bad lol
See SPL.zip in the attachment, which is the SPL from the latest RUU_Kaiser_HTC_WWE_3.28.405.0_radio_sign_25.83.40.02_1.65.16.25_Ship, unzip it then you get RUU_signed.nbh and CustomRUU.exe.
Copy the SSPL-KAIS.exe to your phone (if you had to use the White Screen fix you'll need jwocky2001's JumpSPL1.56-KAIS.exe).
Run SSPL-KAIS.exe from your phone (or JumpSPL1.56-KAIS.exe, depending on your situation).
The Bootloader tri-color screen should appear.
Check SPL version number: if it ends in ".JumpSPL" then everything is fine.
Unplug the USB cable and re-plug it.
Run CustomRUU.exe to flash SPL.
After it's finished verify your SPL by holding down power and camera buttons while doing a soft reset. It should be SPL-3.28.0000.
This is all at your own risk, good luck!
Use at your own Risk!
bengalih said:
So how do I change my SPL?
I would like to make a few amendments/comments to his instructions based on my experiences. The first is that I have found that you don't need to remove you SIM card, but you do need to remove your SD card. The second is that JumpSPL1.56-KAIS.exe will probably not work, so just use JumpSPL1.93-KAIS.exe instead.
Also, step 4 and 5 are very important. Once you have launched JumpSPL you will see, after a few seconds, "USB" appear on the bottom white of the bootloader screen. If it doesn't show then either your device is not plugged into your USB port OR your SD card is still in the device. Remember that once is displays "USB" you want to unplug your USB connection and then reconnect it a few seconds later. No message will display when you plug your USB back in, and ActiveSync will not start (if it does start you should worry!) so assume that everything is ok and continue on.
Using the above procedures you should be able to flash between different SPLs with ease. To summarize I will go through the procedure I use to quickly flash between SPLs. Remember to read the above links first so you understand the tools and basic procedures:
Get the SPL file (in .NBH format) that i want to flash along with the KaiserCustomRUU.exe and put it in a folder on my PC. (just unzip ATT_19213_SPL_3.29.0000.zip)
Plug my device into my PC
Copy JumpSPL1.93-KAIS.exe to your device.
Take out my SD card
Run JumpSPL1.93-KAIS.exe on your device (click on the exe)
Wait for the bootloader screen (tri color screen) to appear and "USB" to show.
Unplug my device from the USB port, wait 5 seconds, plug it back in.
Run KaiserCustomRUU.exe (on your PC) and flash the SPL (in the directory where you unzipped ATT_19213_SPL_3.29.0000.zip)
Your done
Click to expand...
Click to collapse
THese files if using the V3.5 death rom
Use ATT_19213_SPL_3.29.0000.zip for step 1 and 8
Use JumpSPL1.93-Kais.zip for step 3
All of this information can be found in the very informative thread by bengalih found here http://forum.xda-developers.com/showthread.php?t=396235
IT actually appears that you have your SPL already HardSPL'd if you have:
KAIS130 MFG
SPL1.0.olipof
CPLD-8
Therefore you only need to pick the SPL you want and flash it. Now if you want to either change the radio, rom, or spl in the future, you would need to re-do the HardSPL.
Ok. I've had problems up and down and tried and tried to do this and finally got it. So now I'm going to share it with all of you.
1. Download and Unzip the Files in the thread for the Ozone Verizon (HardSPL) posted by JockyW.
http://forum.xda-developers.com/showthread.php?t=551458
2. Connect your phone via ActiveSync, let it sync, and then start the auto.bat.
3. First, the JumpSPL will copy over. Press enter on the computer. Then the SSPL will copy over. Press Enter on the computer. Then it will prompt to start the JumpSPL. Press Enter. JumpSPL should pop up on your phone. Press the silver center button to start JumpSPL. The screen goes black. Then the DOS window will ask you if you have USB Connectivity. DO NOT PRESS ENTER YET!!!!
4. THIS IS VERY IMPORTANT!!! Wait for your phone to disconnect from ActiveSync. Once it does, unplug your phone from the USB. Go into ActiveSync's Connection Settings, and uncheck the box that says ALLOW USB CONNECTIONS. Reconnect your phone to the USB, and it should install the HTC USB Sync driver. NOW PRESS ENTER IN THE DOS WINDOW.
5. The RomUpdateUtility will start up, run it. And it should do the HardSPL on your phone. Your phone will restart when it's finished. If you want to check, before you do any of the above steps, copy the EnterBootloader.exe over to your phone. When you're done with the RomUpdateUtility and the phone has restarted, run the Bootloader and see what the tricolor screen says. It should be 0.39 Hard. Pull the battery, put it back in, restart the phone, and you should be good to go for flashing custom roms!
WOOHOO!
Thanks guys! I'll be donating soon. I'm about to flash the custom 3VO ROM right now! I'll let you know how it goes!
::EDIT:: The 3VO ROM is beautiful and runs like a charm! You guys put so much work into this.
Let it be known that this method for flashing the HardSPL can also be used for flashing the 3VO ROM.
NOTE: I WILL NOT TAKE RESPONSIBILITY FOR BRICKING YOUR PHONE.... seeing as I was scared I almost bricked mine once, and was VERY LUCKY that I did not. Please, follow all directions carefully. Phones are expensive.
ActiveSyn Doesn't disconnect
I got to the step where JumpSPL runs and my screen goes black. However, my phone never disconnects from ActiveSync. I tried unplugging it and disabling USB in activesync, but then my phone comes up as Not Recognized. If I try to run JumpSPL at this point I get, "Error (260): Connection." Any ideas?
How long are you waiting for ActiveSync to disconnect? It takes awhile. I know for me, it took about 5-10 minutes for it to disconnect.
Try waiting a little bit longer, and let us know what happens.
I waited long enough for activesync to stop. I unplugged my phone, disabled USB in activesync, and reconnected my phone. Every time I get a error saying "USB Device Not Recognized." If I try to run the update utility I get a connection error.
In all fairness I bricked my phone initially and had to recover it using a "stock" ROM someone posted for the CEDAR. My phone might just be hosed.
wm 6.5
quick question, the only way i was able to unbrick my phone was by upgrading it to the wm6.5 rom by Verzion, will the HardSPL work with this one?
I flashed the HardSPL on the Verizon 6.5 Update. So I guess the answer would be Yes.
I'm really lovin' this 3VO ROM. It's fast and the battery last a lot longer.
i tried your method and i'm still coming up with SPL-0.39.0000
i've tried other peoples guides as well and cant get it to hardspl, any ideas?
I followed all of these steps a few different times and my Bootloader still says .44. I tried varying the steps a little based on what users said on the thread about putting the HardSPL on the .39 and it still didn't help. I'm going to keep trying various configurations, but if anyone else is able to get their Official 6.5 ROM over to the 3VO, I'd love to hear how.
Thanks
what i need to know is what is hardspl i have an ozone that is unlocked but the data area is still locked to verizson and thats why i need to flash so i need to know what is hardspl and if its needed for an unlocked ozone
recoshaa said:
what i need to know is what is hardspl i have an ozone that is unlocked but the data area is still locked to verizson and thats why i need to flash so i need to know what is hardspl and if its needed for an unlocked ozone
Click to expand...
Click to collapse
You can find the hardspl definition here http://forum.xda-developers.com/wiki/index.php?title=Glossary
If you want to install a custom rom you will need to hardspl your device.
I hope that helps
I ran auto.bat, when the updater failed I disconnected USB from phone, reconnected, then ran updater manually and it all worked. Had to do this on both the HSPL and the ROM.
Also, make sure you don't uncompress both to same folder as it creates a .nbh file and if you have both on same folder you might be trying to install the ROM instead of the HSPL or vice-versa.
Another note. If you are HSPL already you can turn off device, turn it back on pressing DOWN VOLUME and POWER, leave both pressed until you get to rainbow screen, you can then run the updater and it won't bug you with battery being less than 1/2
I had problem that after screen goes blank, the phone will not connect. Some time "HTC USb Sync" will show, some time not. ROM Update will always complain that phone was not connected.
This is what I did to solve.
1. Power Off.
2. Hold vol dn and send with one hand. Then power with other hand.
3. Choose restore default configuration.
4. Let it boot
5. connect to ActiveSync.
6. Now run auto.bat
7. It runs fine and HArd SPL is loaded.
Enjoy.
schoenkn2 said:
quick question, the only way i was able to unbrick my phone was by upgrading it to the wm6.5 rom by Verzion, will the HardSPL work with this one?
Click to expand...
Click to collapse
Hi there, not sure if this belongs here. If you're planning on putting a custom ROM on the Verizon Ozone, do not use the HTC/Verizon wm6.5 update! "!! DO NOT !!" With the original stock wm6.1, you have a .39 Bootloader. After flashing the HTC/Verizon wm6.5 Stock Rom, you have a .44 Bootloader. And you can forget about putting a Custom/3rd Party ROMS. If somebody knows how to fix this, please tell me.
Thanks, and enjoy your HTC!
JD
I had a StockSpl on my Htc touch pro and I wanted to flash an unsigned Hard-SPL from my MicroSD because I wasn't home and I didn't have the USB cable. After the screen loaded 100% the device restarted I took off the MicroSD and now it keep showing this tri-color screen:
RUUNBH
RAPH100
SPL-1.90.000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
Upgrade ROM code error
Please try again
Serial.
(I've also attached a picture)
If i try to flash again from MicroSD the same HSPL it loads until 100% then restart and start to load again until i get the MicroSD card off. Or if i try to flash other StackSPL or any other ROM it stays on Loading on a grey screen.
After I went home I tried to flash the HSPL again from my computer using the USB cable, it start to load 0% then it does nothing. I've tried to flash StockSpl and other ROMs from the computer too but it does the same.
I think i've tried anything but nothing seems to work ... if someone can help me pls ... i've searched the entire forum and there's someone that had almost the same problem here: http://forum.xda-developers.com/showthread.php?t=566796
but noone had any solutions.
You can't flash hard spl off your sd card; it's got to be done through a usb cable.
Just read through the hard spl thread; it's long, but your situation has probably been addressed. I did it almost 3 years ago, so I don't remember the tricks. That's the case with most posters, I'm afraid. Just read the thread.
can u pls tell me which thread?
this one?: http://forum.xda-developers.com/showthread.php?t=410150
or this one?: http://forum.xda-developers.com/showthread.php?t=448008
Either, but read the first one. You can also look in the unlocker thread. Hell, you may just want to buy the unlocker and run that. It will flash hard spl, and the directions may be better.
I just hope they aren't trying to HSPL(hard SPL) a CDMA device :S I've made the mistake to assume the person that was posting in this forum had a GSM device and they really screwed up after a third attempt at flashing HSPL!
Usually if I have a difficult time flashing my Fuze or TP(both GSM), I remove everything to include the battery, connect the USB to an available USB port on the computer then hold the volume down key while connecting the device to the USB cable. Probably not the most friendly way but it certainly will tell you if there is a problem with your USB port/cable or even device!
My htc raphael is GSM
I've tried to hold the volume down button but it's always the same
There's no problem with the cable just that I can't flash anything because I'm stuck with a stock-spl and I can't flash a hard-spl either. When I try to flash something from the computer it starts to flashing with 0% then nothing happends until the RUU gives me the 262 Error. And when i try to flash from my mSD it just stuck with a Loading screen.
Xadow said:
I had a StockSpl on my Htc touch pro and I wanted to flash an unsigned Hard-SPL from my MicroSD because I wasn't home and I didn't have the USB cable. After the screen loaded 100% the device restarted I took off the MicroSD and now it keep showing this tri-color screen:
RUUNBH
RAPH100
SPL-1.90.000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
Upgrade ROM code error
Please try again
Serial.
(I've also attached a picture)
If i try to flash again from MicroSD the same HSPL it loads until 100% then restart and start to load again until i get the MicroSD card off. Or if i try to flash other StackSPL or any other ROM it stays on Loading on a grey screen.
After I went home I tried to flash the HSPL again from my computer using the USB cable, it start to load 0% then it does nothing. I've tried to flash StockSpl and other ROMs from the computer too but it does the same.
I think i've tried anything but nothing seems to work ... if someone can help me pls ... i've searched the entire forum and there's someone that had almost the same problem here: http://forum.xda-developers.com/showthread.php?t=566796
but noone had any solutions.
Click to expand...
Click to collapse
Naughty Naughty..
I guess you realise now that you should ALWAYS read read read before modifying your phone in any way.
What EXACT file did you originally flash to your phone via microsd card and where did you get it from?
If you go into the bootloader screen and then connect the usb cable does it show "usb" at the bottom of the screen?
PLEASE STOP TRYING TO FLASH HARDSPL FROM MICROSD AS YOU CANT DO IT. If you could then it would be in my guide..
Mark.
mskip said:
Naughty Naughty..
I guess you realise now that you should ALWAYS read read read before modifying your phone in any way.
What EXACT file did you originally flash to your phone via microsd card and where did you get it from?
If you go into the bootloader screen and then connect the usb cable does it show "usb" at the bottom of the screen?
PLEASE STOP TRYING TO FLASH HARDSPL FROM MICROSD AS YOU CANT DO IT. If you could then it would be in my guide..
Mark.
Click to expand...
Click to collapse
Thanks for replying
Yes ... I did read the part with the SD flashing but i thought it's not a bit deal to flash from mSD since the flashing via activesync is so easy.
Well ... i extracted the RUU_Signed.nbh from the Hard-SPL found HERE and i copied it to the mSD (MicroSD) and renamed it RAPHIMG.nbh.
I restarted my phone holding the volume down button and it started to load until 100% then it restarted and showed the bootloader screen and after a couple of seconds start to flash the HSPL again so after it completed 2 or 3 times of flashing and restarted i took the battery and the mSD off (I DIDN'T TOOK THE BATTERY WHILE IT WAS IN THE PROCESS OF FLASHING). And when i started the phone again without mSD it showed the bootloader screen like it was waiting to get a .nbh file on mSD to start flashing again.
No matter what i do my phone start in bootloader and down it shows "Serial". If i connect the usb it shows "USB".
I tryed to do a hard reset and it seem to work but after it finish and the phone restarts is stuck with the same tri-colour screen.
Sry for trouble and thx again
I guess I missed the part in the OP where you said it was stuck in bootloader. That's not good. I would try flashing the stock raphael rom (assuming you have it). Have you tried that? I dunno, you may be stuck for good.
Xadow said:
Thanks for replying
Yes ... I did read the part with the SD flashing but i thought it's not a bit deal to flash from mSD since the flashing via activesync is so easy.
Well ... i extracted the RUU_Signed.nbh from the Hard-SPL found HERE and i copied it to the mSD (MicroSD) and renamed it RAPHIMG.nbh.
I restarted my phone holding the volume down button and it started to load until 100% then it restarted and showed the bootloader screen and after a couple of seconds start to flash the HSPL again so after it completed 2 or 3 times of flashing and restarted i took the battery and the mSD off (I DIDN'T TOOK THE BATTERY WHILE IT WAS IN THE PROCESS OF FLASHING). And when i started the phone again without mSD it showed the bootloader screen like it was waiting to get a .nbh file on mSD to start flashing again.
No matter what i do my phone start in bootloader and down it shows "Serial". If i connect the usb it shows "USB".
I tryed to do a hard reset and it seem to work but after it finish and the phone restarts is stuck with the same tri-colour screen.
Sry for trouble and thx again
Click to expand...
Click to collapse
As Farmer Ted said your best bet now is to download your ORIGINAL Rom (from your provider) and flash it from your pc with the usb cable attached. The phone had to be in SSPL mode before running the RUU which is why everything was packed in a single exe. You may have corrupted your SPL in which case you have bricked your phone but if you can manage to flash a Stock Rom then the Stock SPL should be reflashed and you can start again with the HardSPL by following the CORRECT instructions and not making up your own lol.
Good luck.
Mark.
When i bought my phone, the first thing i did was to dump the rom. So now i rebuild it from raw and tried to flash but it didn't work so i went to Orange site and i downloaded the official ROM then started to flash and ... IT WORKS
I think that the ROM was corrupted not the SPL, and since the SPL was stock it didn't allow me to flash other ROMs other then the official
Thanks for all guys I couldn't done this without your help
P.S: why did it allowed me to flash the official rom but the hspl not?
It didn't flash the hard spl because you did it all wrong; those rebuilt roms aren't exactly the same as the stock roms, so it's not surprising that wouldn't flash. Good job finding the original shipped one, though.
Now, just read mskip's instructions and you should be good to go. I think the trick is just to enter bootloader, then connect to your pc through the usb cable.