During WM 6.1 setup, after calibrating the screen the windows custamization setup will run automatically. Is there any way to stop this auto-custamization?
Simply push the Soft Reset button after the calibration.
djtyta said:
Simply push the Soft Reset button after the calibration.
Click to expand...
Click to collapse
Thanks it works. But home screen not visible at all. I think customization is nessasary after all!
skumara said:
But home screen not visible at all.
Click to expand...
Click to collapse
Sometimes I do in such way on official HTC ROM (I can see the progress of customization on the display): when the customization starts after the calibration, I wait till some needed to me applications are being installed and after they've been installed, I simply push the Soft Reset button
Sorry in advance if it won't help to you because I didn't use PcCarvalho's ROM
P. S. Now I use official HTC WM 6.0 ROM because it is stable! I tried many custom ROMs during last 1,5 years: WM 6.1, 6.5 with upper and low start menu, even flashed Android Eclair. But all of them have many troubles, so by my opinion they don't have any chances to be installed on my Polaris!
Related
I think I have suffered from this since installing WM6 (most varients so far....) but it isn't a major problem, however I am sure the behaviour was different in WM5
If my Wizard is 'sleeping' and I receive a call I can use the Talk or Hangup buttons to answer or hangup the call no problems. When in the call if I try and lower the volume using the volume slider on the side it doesn't work. This is because it is locked, if I unlock it the button works. I am sure with WM5 the volume slider worked in a call even when the Wizard was locked?
I am currently running the last Faria WM6 ROM, however I have slightly re-heated it to my taste.
Andy
I'm pretty sure this is because smartskey is installed and configured to override the slider key when using the phone. Change the config and it should work the way you want.
kegobeer said:
I'm pretty sure this is because smartskey is installed and configured to override the slider key when using the phone. Change the config and it should work the way you want.
Click to expand...
Click to collapse
I don't have smartskey installed, this is one of the things I removed....
it might suck.... but a hard reset might be all it takes to fix the problem
Hang on, I'm running WM5 and smartskey. Even with Smartskey the vol slider works in phone mode (device unlocked). I just called myself with the device locked, the slider and all buttons are ineffective except for the pickup and hang-up keys. So, there it is!!
Also, with the device locked, you can only hang up after a call, you can not hit the red key again to bring you back to the Today screen, you have to unlock for that.
Zack84a said:
it might suck.... but a hard reset might be all it takes to fix the problem
Click to expand...
Click to collapse
Well this is maybe the 15th or so time I have re-flashed WM6 on this Wizard and it's been the same on all of them, I think a hard-reset won't fix anything
ADB100 said:
Well this is maybe the 15th or so time I have re-flashed WM6 on this Wizard and it's been the same on all of them, I think a hard-reset won't fix anything
Click to expand...
Click to collapse
It's normal ops withthe device locked.
hmmm....
have you tried flashing a different rom other than farias?
Zack84a said:
hmmm....
have you tried flashing a different rom other than farias?
Click to expand...
Click to collapse
All of them.... Well, ROM's based on each of the 3(4?) base ROMs that have appeared. I am now wondering whether this might be a Battery Status thing since I have kept the same Battery Status settings throughout...
Andy
Zack84a said:
hmmm....
have you tried flashing a different rom other than farias?
Click to expand...
Click to collapse
I've tried other WM5 ROMs, such as Molski's AKU 3.2, and if I remember, it did the same thing. Perhaps someone with another WM6 rom loaded can experiment and let us know if the same happens to them.
Anyone???
EDIT: I am using Batt status to lock it. I can try another lock program, hang on!!
Well, I tried just the Today plug-in lock, and the same thing happened, however, I can't rule anything out, I not sure if that plug-in uses BSdevicelock.exe or a different one. I did a search for devicelock and the only file that popped up was the BSdevicelock. I need to find a different one and try it.
UPDATE:
I tried a diffrent devicelock program and the same thing happend.
I've used a bunch of roms so far and two of them so far have worked fine for days but for some weird reason when I would turn it on then it wouldn't turn on anymore. I am not gonna mention names because I don't think it's their fault I think it's mine. Both of them tended to do this right after I installed new software and then later on I would restart the phone. Is there some type of limitation of how much I could third-party software I could install in a rom?
Elmi said:
I've used a bunch of roms so far and two of them so far have worked fine for days but for some weird reason when I would turn it on then it wouldn't turn on anymore. I am not gonna mention names because I don't think it's their fault I think it's mine. Both of them tended to do this right after I installed new software and then later on I would restart the phone. Is there some type of limitation of how much I could third-party software I could install in a rom?
Click to expand...
Click to collapse
Ok my guess is you are using a touch rom. Here is what I am willing to bet has happened to you. You flashed the rom successfully, installed 3rd party software while the home plugin was still active on the home screen and now you are having problems rebooting.
I have 3 solutions for you.
1. Hard reset(hold comm manager and voice button while pressing reset button.)
2. take out memory card and sim card turn it on and then soft reset once it freezes.
3. DISABLE home plugin while installing new software.
Hope this helps.
dharvey4651 said:
Ok my guess is you are using a touch rom. Here is what I am willing to bet has happened to you. You flashed the rom successfully, installed 3rd party software while the home plugin was still active on the home screen and now you are having problems rebooting.
I have 3 solutions for you.
1. Hard reset(hold comm manager and voice button while pressing reset button.)
2. take out memory card and sim card turn it on and then soft reset once it freezes.
3. DISABLE home plugin while installing new software.
Hope this helps.
Click to expand...
Click to collapse
How do I go about disabling the home plugin temporarily?
Elmi said:
How do I go about disabling the home plugin temporarily?
Click to expand...
Click to collapse
Settings->today->Items->uncheck HTC home
Brother had a bad battery today. Caused it to loop splash screens. Switched battery with mine and fixed the problem. weired
these dvices act weired with bad battires
elhamy said:
these dvices act weired with bad battires
Click to expand...
Click to collapse
Yea that's no joke. Just today my Wizard running TNT.1437 Touch started trying to connect to GPRS over and over again and wouldn't stop untill the battery completely died. It was only at 3% to begin with but it died really quick(batterystatus probably helped)
First of i have looked in many thred but could not get my answer so I posting this.
I was on dutty's new wm6.1 rom but with radio 1.64 but due to constant freezing and gps issue i decided to go back wm 6.0. so i flash my tilt with Duttys Dualtouch v4 RTM.7. everything went ok but now issue is I can not reboot my phone. I after setting up date etc. customisation started and then soft reset. after that soft reset my tilt just hang at dutty's series screen does not go any further. I have tried hard rest, soft rest , going to three color screen and amny other that i can think of but every time i hang (htc log in center, hTc word in middle and dutty's series at right buttom screen). I waited for long time in that case phone goes into blank screen and when i press power it show me some wired screen with many colored dots. ( it that waht called I bricked my tilt). Is there any way to flash tilt via sd card? I show few thread on this site but they are for different brands phone. if there is a way can some one tell me how?
Reset to three color screen with USB
Hit reset, camera and power button all at a time, you will see the three color screen, put your usb port and flash with old rom. That's it....
v3patel said:
First of i have looked in many thred but could not get my answer so I posting this.
I was on dutty's new wm6.1 rom but with radio 1.64 but due to constant freezing and gps issue i decided to go back wm 6.0. so i flash my tilt with Duttys Dualtouch v4 RTM.7. everything went ok but now issue is I can not reboot my phone. I after setting up date etc. customisation started and then soft reset. after that soft reset my tilt just hang at dutty's series screen does not go any further. I have tried hard rest, soft rest , going to three color screen and amny other that i can think of but every time i hang (htc log in center, hTc word in middle and dutty's series at right buttom screen). I waited for long time in that case phone goes into blank screen and when i press power it show me some wired screen with many colored dots. ( it that waht called I bricked my tilt). Is there any way to flash tilt via sd card? I show few thread on this site but they are for different brands phone. if there is a way can some one tell me how?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=336158
the procedure is in there
thank you for quick answer.
it worked I know i can always coutn on you. Once agin thanks
v3patel said:
it worked I know i can always coutn on you. Once agin thanks
Click to expand...
Click to collapse
LOL....should have flashed the radio first
Like the other person said...go the boot loader (aka tri color screen) and install a compatible WM6 Radio.
Khanki said:
Hit reset, camera and power button all at a time, you will see the three color screen, put your usb port and flash with old rom. That's it....
Click to expand...
Click to collapse
THK THK THK!!!!!!
Hello forum members,
would you please help me have the BT HTC S710 Original ROM? I have only seen the BT HTC S620, which when I tried to flash with to rebrand, blanked my HTC S710 screen. When I turn it on, only the two green lights come on either side of the phone ear piece.
It means that a hard reset is not visible on my screen, there is no tri-colour display either.
I have tried other ROMS, and get invalid id errors and error 270. I have tried Dr Gonzo and related ROMS.
It's now three days, no phone no pim, I am lost.
Thanks for your attention.
YOSEFE.
PS. You may PM me if convenient.
Hi YOSEFE,
I have the same problem
I tried the 620 rom and just have the 2 green LED's. I cannot get a bootloader screen and attempts to flash new roms get to 3% and then I get errors.
Did you ever sort this problem out?
Paul.
Have you unlocked ur USPL in ur phone?
You tried to flash a S620 ROM to a S710???? Look in the Wiki, there is a link to the official ROMs on the ftp...
frauhottelmann said:
You tried to flash a S620 ROM to a S710???? Look in the Wiki, there is a link to the official ROMs on the ftp...
Click to expand...
Click to collapse
Yes, I'm afraid I did, by mistake, flash 620 ROM to the 710 [feels rather stupid!]
Not happy with BT’s [mobile operator] own ROM and software that went on the phone, I successfully flashed Dr. Martin Gonzo’s Windows Mobile 6.1 v1.1 and have been using it for a couple of months but when BT launched their new phone software, I decided to try it but because it won’t work with WM 6.1, I needed to then revert back to BT’s old ROM and this was the only one available that I could find [feels rather stupid again].
The screen is completely black; only green LED's on each side of the earpiece shows any sign of life.
Connecting the phone via ActiveSync shows “HTC-S620 Connected” and I am able to browse the files on the phone but not having a display on the phone, I am limited to what I can do.
I have tried running RUU_Vox_HTC_WWE_1.34.405.1_4.1.13.54_03.10.90_Ship.exe but ActiveSync connection is lost and I hear the Windows hardware removed sound shortly after the progress bar is shown.
I’m at a loss as to what to try
Paul.
Shut it down, then hold down camera button and plug in the usb cable. The boot screen should appear and you should be able to flash the normal ROM!
I cannot get the boot screen, or any screen for that matter.
I have tried taking the battery out to make sure the phone is off. Reinserting that battery then holding the camera button down and then inserting the usb lead. The keypad lights up for a few seconds then goes out. ActiveSync then connects but the screen is still black
Paul.
[Edited: Sorry duplicate post]
Sorry for replying to my own post but a quick update...
I have managed to bring the phone back to life and reinstall Dr. Martin Gonzo’s Windows Mobile 6.1 v1.1 on it again.
This is partly assumption and not particularly accurate but the original poster (YOSEFE) might find this useful.
By installing the S620 rom on the S710, not only did I make the screen go blank, I think all the keys ended up remapped and mixed up, therefore any attempt to install Gonzo’s rom ultimately ended in failure because when the phone beeped and wanted a keypress to continue, pressing the left softkey for ‘OK’ or ‘Yes’ did not work because it had been remapped to do something else.
What worked for me is that when the phone beeped during the uspl_116_jockyw.bat install, I pressed the X or C key (I can’t remember the exact one now). One of these keys must have been the ‘OK’ or ‘Yes’ key after the S620 rom muddled things up. I only know this by trial and error over the period of today.
To my glee, the backlight lit up on the display and after a bit of tinkering, I’m back in action again
I won’t be installing a rom designed for another model again!
Paul.
Bat 'n' Ball,
sorry for not returning here to see your post. I will remember the possibility of pressing "X" or "C", should I make the same mistake as before, although like you, I should never do that ever again. However, technology being what it is, who knows?
In the end BT got me sorted out.
Thanks for sharing.
thanks to cotulla we could see wm 6.5 on magician both 46m and 128m memory..
But every time i upgrade to the latest rom .. I find that i have to downgrade again to rom 3.03 because it's the last rom to have the " no button lock" option.. But all the roms came after do not have this option ..and the only button to use to turn on/off the device "magician" is the power on/off button..
Which is made of rubber in most of devices.. And if it's not broken in your magician, it will be very soon..
But if it's already broken or has any problem .. You will not be able to use any of the roms after 3.03..
So you will have to downgrade to this rom to be able to use your magician...
I hope cutolla or any one can find a fix to this issue to allow buttons other than power button to work.. Thank you.
tarekezzat said:
thanks to cotulla we could see wm 6.5 on magician both 46m and 128m memory..
But every time i upgrade to the latest rom .. I find that i have to downgrade again to rom 3.03 because it's the last rom to have the " no button lock" option.. But all the roms came after do not have this option ..and the only button to use to turn on/off the device "magician" is the power on/off button..
Which is made of rubber in most of devices.. And if it's not broken in your magician, it will be very soon..
But if it's already broken or has any problem .. You will not be able to use any of the roms after 3.03..
So you will have to downgrade to this rom to be able to use your magician...
I hope cutolla or any one can find a fix to this issue to allow buttons other than power button to work.. Thank you.
Click to expand...
Click to collapse
select >> Start & Lock ..
look like Nokia Mobile phone.
it's not that easy man.. iam not talking about how to lock my phone .. i know it's start>>lock.. i'm talking about how to turn on the phone.. after the regular sleep mode of non-use for couple of minutes...?????
yes
i realized this problem too.Cotulla,can you tell me how i can waken my phone with touching my screen. i was told this might work, but it never worked. i have to press my power button again and again when i want to waken my phone or even when i make a phone call. what a pity