I have searched this forum but to no avail.
I have a Cingular 8125 running the 2.25 IPL/SPL it is SIM & CID unlocked.
I am able to flash the TMOBILE Radio rom no problem, BUT everytime I try to flash crossbow reloaded 1.5 and/or Faria's CROSSBOW it hangs at 99% and then faults out with an error code of 302 communication error.
My device then gets pseudo bricked and I have to reflash back with the Cingular rom.
Any ideas or tips?
whammie said:
I have searched this forum but to no avail.
I have a Cingular 8125 running the 2.25 IPL/SPL it is SIM & CID unlocked.
I am able to flash the TMOBILE Radio rom no problem, BUT everytime I try to flash crossbow reloaded 1.5 and/or Faria's CROSSBOW it hangs at 99% and then faults out with an error code of 302 communication error.
My device then gets pseudo bricked and I have to reflash back with the Cingular rom.
Any ideas or tips?
Click to expand...
Click to collapse
Try starting the flash in bootloader screen. Turn device off then hold camera button. then push power button. Keep holding camera button till you see the rainbow screen
The usual suggestions - perform a hard reset, remove the SD card, make sure all other apps are shut down, etc, etc, etc.
Also, starting out with a good, strong 2.26 IPL/SPL ROM might help. It's been suggested many, many times to flash to the T-Mobile 2.26 ROM as a solid base before upgrading to WM6.
ROM updat Problems
newbie2 said:
Also, starting out with a good, strong 2.26 IPL/SPL ROM might help. It's been suggested many, many times to flash to the T-Mobile 2.26 ROM as a solid base before upgrading to WM6.
Click to expand...
Click to collapse
I have had the miniSD card out, I have shutdown all applications. I will try it from directly in the bootloader screen. As far as the 2.26 ROM I could not get it on my device, gave me an error as wrong Vendor ID.
whammie said:
I have had the miniSD card out, I have shutdown all applications. I will try it from directly in the bootloader screen. As far as the 2.26 ROM I could not get it on my device, gave me an error as wrong Vendor ID.
Click to expand...
Click to collapse
My suspicion is that you are not truely CID unlocked. May want to retrace those steps.
Good luck!
8125 ROM Upgrade
Thanks to all for the help.
It turns out that I was most likely not truly CID unlocked. Redid it based on the post in this forums and VOILA. Worked like a charm.
Thanks to all on this forum for all the hard work and helpful advice.
Hi, I have just received an at&t tilt 8025 sim unlocked, I am trying to upgrade to original htc rom, I have installed hardspl and the process start but always stopped with error in 0% upgrading step, no way
any suggestions?
Do you get a error code? If yes what error code.
yes, error 262
Ok, I have more information, if the rom I want to upgrade is base rom only NO problem, if rom contains radio or I try to flash a radio version I never gets 100%
A clue, the tilt is an ebay UNLOCKED at&T , may be the unluck is the cause of radio upgrade probles??
try to change the other datacable and do it again
change datacable??? I don.,t understant what you say, there is only a datacable for tilt isn,t ?
Error Codes 26x are generally related to USB communication errors. That is why it was suggested that you try a different cable. (Or a different USB port)
I would also try using a different PC, if possible. You can also try flashing via MicroSD card, if you have one. Do a search for MicroSD flashing on the Kaiser Upgrading forum, there is a very detailed step by step process listed on how to do this.
Treo's are gayy..
and that relates how exactly?
Hey guys! been lurking around the forums for eons, but haven't 'dove in' till just recently. Have a couple of questions.
Some months ago I did the free upgrade to WinMO 6.1.
I got Tilt SID unlocked by calling up AT&T and telling them I was going to Europe. My T-mobile SIM card is working just fine.
After a few hours of cussing, I managed to beat HardSPL 3.56 into my phone, because it already had SPL 3.56 on it.
Now I'm stuck trying to CID unlock and I can't seem to find a utility to work with it. The 'chain' of threads I followed dead ended saying downgrade to get it work, but I don't want to do that. I had a hard enough time getting HardSPL 3.56 to install. Then I ran across Jockyw's CID unlocker http://forum.xda-developers.com/showthread.php?p=1837147 and found myself saying ooo and ahh! But, it won't work with ANY 3.xx HardSPL.
Is there a CID unlocker compatible with 3.56??
I'd love to have AT command mode stuff and etc. from jockyw's, but at this point I think I'll take whatever I can get without needing to downgrade.
I can't seem to find it now, but didn't there used to be a list of pre-cooked ROMs here somewhere?
I think what I'm aiming at is a fully patched / hacked 6.1 HTC ROM with everything fixed and no bugs. Preferably minus any bloatware. If it has recommended utilities pre-installed great, if not, no big loss. Did they ever finish hacking a video driver together? I lost track of that thread, and can't seem to find any current info.
I've been waiting for a working Linux distro for a HTC device for years, but I'm going to throw in the towel and make the best of what I can get on windows. I've spent over $3000 on these HTC devices over the years, but don't rely on them because of all the bugs. Once I get my Tilt patched up, I'm jumping ship and trading in my old ones for a G1.
Thanks for any help!
p.s. I DO have to CID unlock before I can install any other ROMs.. right??
p.p.s. Here's all the details if it's any help:
rom version 3.57.502.2 WWE
rom date 7/17/08
radio version: 1.65.21.18
protocol version: 25.88.40.05H
tri-color screen
KAIS1*0
SPL-3.56.0000
CPLD-8
.
.
Serial
image version 3.57.502.2
R 1.65.21.18
G 25.88.40.05H
D 3.57.00.00
Note: This is BEFORE I updated to HardSPL 3.56
Thanks again!
If you have any of the HARD SPL installed(3.56 from your words).
You can flash any ROM you want.
No need to CID unlock separately.
With Hard SPL, your Device is CID unlocked already.
Your pda doesn't not have hard spl installed on it
Crogon said:
Hey guys! been lurking around the forums for eons, but haven't 'dove in' till just recently. Have a couple of questions.
Some months ago I did the free upgrade to WinMO 6.1.
I got Tilt SID unlocked by calling up AT&T and telling them I was going to Europe. My T-mobile SIM card is working just fine.
After a few hours of cussing, I managed to beat HardSPL 3.56 into my phone, because it already had SPL 3.56 on it.
Now I'm stuck trying to CID unlock and I can't seem to find a utility to work with it. The 'chain' of threads I followed dead ended saying downgrade to get it work, but I don't want to do that. I had a hard enough time getting HardSPL 3.56 to install. Then I ran across Jockyw's CID unlocker http://forum.xda-developers.com/showthread.php?p=1837147 and found myself saying ooo and ahh! But, it won't work with ANY 3.xx HardSPL.
Is there a CID unlocker compatible with 3.56??
I'd love to have AT command mode stuff and etc. from jockyw's, but at this point I think I'll take whatever I can get without needing to downgrade.
I can't seem to find it now, but didn't there used to be a list of pre-cooked ROMs here somewhere?
I think what I'm aiming at is a fully patched / hacked 6.1 HTC ROM with everything fixed and no bugs. Preferably minus any bloatware. If it has recommended utilities pre-installed great, if not, no big loss. Did they ever finish hacking a video driver together? I lost track of that thread, and can't seem to find any current info.
I've been waiting for a working Linux distro for a HTC device for years, but I'm going to throw in the towel and make the best of what I can get on windows. I've spent over $3000 on these HTC devices over the years, but don't rely on them because of all the bugs. Once I get my Tilt patched up, I'm jumping ship and trading in my old ones for a G1.
Thanks for any help!
p.s. I DO have to CID unlock before I can install any other ROMs.. right??
p.p.s. Here's all the details if it's any help:
rom version 3.57.502.2 WWE
rom date 7/17/08
radio version: 1.65.21.18
protocol version: 25.88.40.05H
tri-color screen
KAIS1*0
SPL-3.56.0000
CPLD-8
.
.
Serial
image version 3.57.502.2
R 1.65.21.18
G 25.88.40.05H
D 3.57.00.00
Note: This is BEFORE I updated to HardSPL 3.56
Thanks again!
Click to expand...
Click to collapse
I'm sorry to tell you that this:
KAIS1*0
SPL-3.56.0000
CPLD-8
Is not hard spl and if you pda has hard spl installed is will say this:
KAIS1*0
SPL-3.56.Hard
CPLD-8
I received my replacement Tilt 4 days ago from At&t and it came with WM6.1 and spl 3.56.0000 and you are right I cant find anything to change that spl. I have tried to CID UNlock and I get the white screen, so I tried jump spl 1.56 and 1.93 and neither one of them worked. So now I'm stuck with this 3.56.0000, I sent Jocky a PM and He told me that he was looking in to it and that he will get back to me. So I have to wait. Or maybe someone will read this that has a fix for this issue and help us.
I just bought my Tilt too, it also came with 3.56 and WM6.1 but I had NO problems unlocking and flashing hard SPL to it.
Now, what happens when you run Jump 1.93? and are you running it directly from your main memory NOT from a SD card, and no SD card is in the phone?
If you follow the directions EXACTLY it will work.
1 Run Jump SPL from your main memory
2 tri color boot screen saying jump 1.93 should show up, with USB at the bottom
3 Unplug your device wait 30 sec and plug it back in
4 In Active sync on your PC disable USB connections (I've actually flashed spl's without doing this)
5 Now run the customRUU with the hard spl file you want to upload.
BerettaFreak said:
I just bought my Tilt too, it also came with 3.56 and WM6.1 but I had NO problems unlocking and flashing hard SPL to it.
Now, what happens when you run Jump 1.93? and are you running it directly from your main memory NOT from a SD card, and no SD card is in the phone?
If you follow the directions EXACTLY it will work.
1 Run Jump SPL from your main memory
2 tri color boot screen saying jump 1.93 should show up, with USB at the bottom
3 Unplug your device wait 30 sec and plug it back in
4 In Active sync on your PC disable USB connections (I've actually flashed spl's without doing this)
5 Now run the customRUU with the hard spl file you want to upload.
Click to expand...
Click to collapse
Yes I did all that I'm very familar with the process this is my 5th tilt 2 of them the CID Unlock run just fine and the other 2 I that to run jump 1.56 to get pass the white screen. But for some reason I cant get anything to work on this tilt. I even try to install the OG WM6.0 to try to downgrade the spl but that did work either. Do you have any other suggestions?
IIRC for me to run the CID unlocker program I needed to flash the SPL first.
What is happening when you are trying to run the Jump SPL files? It's just not making sense.
You need to flash Hard SPL 3.29 BEFORE you try to run the unlocker, you can't do 3.56 then try to unlock it. Once its unlocked then flash it with hard 3.56 if you so desire.
Also after doing the 3.29 spl you need the proper cracked radio flashed to allow you to unlock the device, are you skipping that step?
It sounds like your trying to do an SPL upgrade and NOT SIM unlock the device since that step comes after.
BerettaFreak said:
Also after doing the 3.29 spl you need the proper cracked radio flashed to allow you to unlock the device, are you skipping that step?
It sounds like your trying to do an SPL upgrade and NOT SIM unlock the device since that step comes after.
Click to expand...
Click to collapse
No what I'm trying to do is CID Unlock my phone but is not working I get the white screen. I have tried everything I know to get pass it. I'm not trying to install hard spl 3.29 or 3.56. I have to CID Unlock my phone first right? That is what I've always done before. I'm out of ideas.
What is on your phone right now?
Factory SPL?
Factory 6.1 rom?
If so you need to run Oli's Sim Unlocker and CID Unlocker exe, this will FIRST flash a 3.29 hard SPL to your phone, THEN then next step is to flash a cracked radio and then you can sim and CID unlock your phone. As noted before tho a CID unlock is NOT necessary, if your Sim unlocked and Hard SPL'd you can do whatever you want to the phone.
BerettaFreak said:
What is on your phone right now?
Factory SPL?
Factory 6.1 rom?
If so you need to run Oli's Sim Unlocker and CID Unlocker exe, this will FIRST flash a 3.29 hard SPL to your phone, THEN then next step is to flash a cracked radio and then you can sim and CID unlock your phone. As noted before tho a CID unlock is NOT necessary, if your Sim unlocked and Hard SPL'd you can do whatever you want to the phone.
Click to expand...
Click to collapse
Thank you very much for all your help BerettaFreak you are the man!
Heeey! Did my thread get hijacked?
Lol, Ok where to start..
skr_xd:
If you DON'T need to CID unlock, then the Newb instructions are a bit confusing. Why does it say to install HardSPL, then CID unlock?
What or why would I need to CID unlock separately? ..or is it the Security unlock bit, Or SuperCID that I'm still missing? There must be some point to it, Because Oli's Does HardSPL then SIM unlock, THEN CID unlock.
Vol22002:
I DID get HardSPL 3.56 installed. I used JumpSPL 1.56. DO remember to yank out the SD and SIM card. Note the very bottom of my post says those stats listed are BEFORE I installed HardSPL.
I still need some more help with finding a ROM, but I suppose that would be best addressed in a new thread, so I'll do that.
Thanks again!
Crogon said:
Lol, Ok where to start..
skr_xd:
If you DON'T need to CID unlock, then the Newb instructions are a bit confusing. Why does it say to install HardSPL, then CID unlock?
Click to expand...
Click to collapse
CID Unlocking is done by installing the Hard SPL, the Hard SPL's don't check the Carrier ID (CID) when flashing new ROM's.
Crogon said:
What or why would I need to CID unlock separately? ..or is it the Security unlock bit, Or SuperCID that I'm still missing? There must be some point to it, Because Oli's Does HardSPL then SIM unlock, THEN CID unlock.
Click to expand...
Click to collapse
SuperCID Set's your CID to 11111111, Security unlock removes an extra check when Flashing Radios to avoid you getting stuck on some radios.
Crogon said:
Vol22002:
I DID get HardSPL 3.56 installed. I used JumpSPL 1.56. DO remember to yank out the SD and SIM card. Note the very bottom of my post says those stats listed are BEFORE I installed HardSPL.
I still need some more help with finding a ROM, but I suppose that would be best addressed in a new thread, so I'll do that.
Thanks again!
Click to expand...
Click to collapse
Just follow all the steps in the Guide by mskip and post and problems you have there. Understanding is not a pre-requisite, with that guide, you can figure out what all the steps do later...
Simply put:
HardSPL / CID Unlock / Super CID - Allows ROM's and Radio's to be flashed.
SIM Unlock - Allows you to use a foriegn SIM card
Security Unlock - Avoids problems when flashing some Radios.
Ta
Dave
DaveShaw said:
SuperCID Set's your CID to 11111111, Security unlock removes an extra check when Flashing Radios to avoid you getting stuck on some radios.
Security Unlock - Avoids problems when flashing some Radios.
Click to expand...
Click to collapse
Hey, thanks for the fast reply Dave!
Ok, So I COULD still Security unlock it, If I could find a security unlocker that worked with 3.56.
The bit about problems flashing radios sounds a bit like something that happens right before your phone becomes a brick. Could you point me to a resource about problem radios or how to avoid them?
I actually prefer to leave the radio alone, if I can get away with it. I just want a patched up ROM, as I mentioned earlier and in my new thread.
Anyway, If I end up needing to replace my radio, how do I avoid 'problem ones'. I understand that some radios simply don't work with some ROMs, but you seem to be eluding to something different here.
Thanks again!!
Crogon said:
Hey, thanks for the fast reply Dave!
Ok, So I COULD still Security unlock it, If I could find a security unlocker that worked with 3.56.
The bit about problems flashing radios sounds a bit like something that happens right before your phone becomes a brick. Could you point me to a resource about problem radios or how to avoid them?
I actually prefer to leave the radio alone, if I can get away with it. I just want a patched up ROM, as I mentioned earlier and in my new thread.
Anyway, If I end up needing to replace my radio, how do I avoid 'problem ones'. I understand that some radios simply don't work with some ROMs, but you seem to be eluding to something different here.
Thanks again!!
Click to expand...
Click to collapse
To Security Unlock, just follow this guide: http://forum.xda-developers.com/showthread.php?t=361236
Then upgrade to HardSPL 3.56 again.
Security Unlocking is done by setting a flag in the NAND. It's permanent (unless you re-lock) and there are no comptability problems once it is set (you need to use a special Hard SPL to set it first though).
EDIT:
There is no list of known bad radio's - only the "Radio from Hell" 1.65.17.10 - but another Radio from hell could appear any day
Ta
Dave
Thanks for clearing that up Dave.
I think I'm going to opt to ignore the security unlock, since it sounds like it's on an 'as needed' basis.
I have 'batter fish to fry' at the moment. I'm grinding gears trying to figure out HOW to figure out which ROMs I should be looking into, in my other thread.
By the by guys, I was joking about the 'hijacked thread' thing, I'm sure somebody will find the info useful.
Just when i though I had this all figured out and was about to Flash my first ROM.
I have read and re-read the flashing wikis and am still confused.
If your on WM6 then you need to use Jockyw2001's Kaiser SuperCID and Security Unlocker v0.1 right? But if you are on WM6.1 then you use Olipro's Kaiser SIM/CID Unlocker & Changer right?
Well I am currently on WM6 pro and dont want to upgrade to 6.1 just to use Olipro's program. So I would go with Jocky's right. Then people say you need to flash a HardSPL first before doing the SuperCID and Security Unlocker. But then in Jocky's directions it says Note that the security unlocker does not work with "SPL-3.28.Hard" and "SPL-3.29.Hard".
So what SPL do you start with.
And I know Dave already told me this earlier that since I have an AT&T Tilt and I am with AT&T service then I dont have to worry about SIM unlocking obviously. So can I skip the whole CID/SUPER CID/SECURITY UNLOCK routine. Can I just Flash HardSPL 3.29 or 3.56 and then start playing with ROMS till my hearts content or is all the security stuff really that neccessary?
So I am lost once again. Wow. I dont know why I am not getting this.
P.S. On another note, I am using AT&T Tilt with shipped ROM running WM6 pro. I have about 40-50 programs installed on it. When first setting up my phone I did the soft reset which supposedly gets rid of the bloatware. Anyways, with all my programs and it being the stock ROM I still have 62MB free PROGRAM RAM. I do however only have like 30MB Storage RAM. But 62MB of free PROGRAM RAM. I see people with naked ROMS that only get like 55MB of free PROGRAM RAM, is my phone like magic or something? Just curious as to how this may be possible.
asofiker said:
Just when i though I had this all figured out.
I have read and re-read the flashing wikis and am still confused.
If your on WM6 then you need to use Jockyw2001's Kaiser SuperCID and Security Unlocker v0.1 right? But if you are on WM6.1 then you use Olipro's Kaiser SIM/CID Unlocker & Changer right?
Well I am currently on WM6 pro and dont want to upgrade to 6.1 just to use Olipro's program. So I would go with Jocky's right. Then people say you need to flash a HardSPL first before doing the SuperCID and Security Unlocker. But then in Jocky's directions it says Note that the security unlocker does not work with "SPL-3.28.Hard" and "SPL-3.29.Hard".
So what SPL do you start with.
And I know Dave already told me this earlier that since I have an AT&T Tilt and I am with AT&T service then I dont have to worry about SIM unlocking obviously. So can I skip the whole CID/SUPER CID/SECURITY UNLOCK routine. Can I just Flash HardSPL 3.29 or 3.56 and then start playing with ROMS till my hearts content or is all the security stuff really that neccessary?
So I am lost once again. Wow. I dont know why I am not getting this.
Click to expand...
Click to collapse
There is a Hard SPL 1 by pof. Flash that first then follow Jocky's instructions.
Also the OliPro Security unlock isn't permenant, next time you flash a Radio it's gone.
Ta
Dave
Ok so Flash the Hard SPL 1 by pof
Then follow Jockys directions in using his Kaiser SuperCID and Security Unlocker v0.1
Then Flash either HardSPL 3.29 or 3.56. WHichever I choose?
Then go crazy with playing with different ROMS.
P.S. So every time you Flash a HardSPL it overwrites the previous one? Or do you have to get rid of a HardSPL first before putting a new one on?
asofiker said:
Ok so Flash the Hard SPL 1 by pof
Then follow Jockys directions in using his Kaiser SuperCID and Security Unlocker v0.1
Then Flash either HardSPL 3.29 or 3.56. WHichever I choose?
Then go crazy with playing with different ROMS.
P.S. So every time you Flash a HardSPL it overwrites the previous one? Or do you have to get rid of a HardSPL first before putting a new one on?
Click to expand...
Click to collapse
Flashing a new SPL overrides the old one.
You said before you were happy with WM6.0, if so use either the pof Hard SPL v1 or the jockyw Hard SPL v1.1 (Part of the security unlock); if you are using WM6.1, use one of the jockyw or cmonex Hard SPL 3.**. Using the wrong version won't break your phone, but Windows will randomly freeze.
Ta
Dave
Thanks again Dave for helpin me out and not tearing me a new one. But just one last question.
If I find a new ROM that I want to Flash and it uses WM6.1 then I have to make sure that I flash a HardSPL 3.xx before flashing that new ROM, is that what ur saying?
Phone: UK T-mobile branded (vario IV) Raphael (GSM)
Been running custom roms & radios since i got it, had hard-spl on it.
The phone has a fault, so needs to be returned to factory settings for warrenty.
Problem 1)
The fault is with the mini-usb connector - so it is not possible to establish a data link to a pc
Problem 2)
Restoring everything!
I replaced the rom, radio, undid the security unlock & replaced the splash screen - all ok
Replacing the SPL i ran into problems (and then made it all worse!). I used a rebuilt spl 1.69 (what the phone shipped with) - which flashing from SD card loaded ok, but wouldnt overwrite the hard spl. (it loaded 100%, reset and still on hard spl)
I then read that the OliNex 1.90 warrenty restore spl was the only one which would overwite hard spl, but once i had done that, i could then write the correct spl back to the phone.
The 1.90 flashed from the sd card fine. Now the device starts on the boot loader saying i have an "Upgrade ROM code error Please try again"
However, it wont let me flash anything from the SD card now - i've tried the correct (1.69) spl, hard spl, the original (restored) rom and a HTC original rom.
The screen starts on the boot loader, then changes to the grey flashing screen where it says "loading..." (before flashing spl 1.90 this lasted less than 2 secs before saying what was on the sd card to flash) and never loads the nbh from the sd card to accept or not.
I've tried re-formatting the sd card again.
If anyone can help with this i'd be extremely greatful. But, please dont suggest anything from the pc - it simply wont connect (its not a windows, activesync or .net problem - the phone has a hardware fault)
my best guess is that the SPL you flashed locked the Carrier Code and you can't flash any rom besides one that matches the carrier code... or something went corrupt and the code is bad
Slight update:
It seems the HTC rom i tried in post 1 wasnt an original one, but rebuilt.
If i use a "new" and i guess signed NBH it passes the "loading..." screen onto "checking..." before telling me its not allowed.
Is there anyway of ID'ing the "expected" ID? and then is there a way of supplying that ID to a custom nbh?