Related
OK please don't flame me as I am going round and round in circles jumping from one thread link to another trying to get to grips with this stuff!
OK...
The other day I tried to install the hardspl and got the white screen problem.
I followed the thread to sort that out and all appeard ok and the phone continued to work OK under HTC stock 6.1
Yesterday I flashed L26_Kaiser_Diamond_V8_light release and have been playing around with it trying to sort stuff out.
I then started reading the thread about ultimate radios and trying to work out what other radios work with this ROM and how I go about installing them and read I need to confirm the spl I am on and so did the hold camera button and reset to see the spl version.
It says the following:
KAIS130 MFG
SPL-1.0.0liPof
CPLD-8
Now from what I understand it should say SPL-3.2X or similar?
But it does not?
I thought that I needed the SPL-3.2X etc in order to flash cooked ROMS but it looks like I dont have that......so how was I able to flask L26_Kaiser_Diamond_V8_light release ?
Thanks
pachjo said:
OK please don't flame me as I am going round and round in circles jumping from one thread link to another trying to get to grips with this stuff!
OK...
The other day I tried to install the hardspl and got the white screen problem.
I followed the thread to sort that out and all appeard ok and the phone continued to work OK under HTC stock 6.1
Yesterday I flashed L26_Kaiser_Diamond_V8_light release and have been playing around with it trying to sort stuff out.
I then started reading the thread about ultimate radios and trying to work out what other radios work with this ROM and how I go about installing them and read I need to confirm the spl I am on and so did the hold camera button and reset to see the spl version.
It says the following:
KAIS130 MFG
SPL-1.0.0liPof
CPLD-8
Now from what I understand it should say SPL-3.2X or similar?
But it does not?
I thought that I needed the SPL-3.2X etc in order to flash cooked ROMS but it looks like I dont have that......so how was I able to flask L26_Kaiser_Diamond_V8_light release ?
Thanks
Click to expand...
Click to collapse
Read the SQL Questions thread in the Wiki. It will explain a lot of this to you.
In short, any HardSPL will allow you to flash, it's just the 3.* ones are more compatable with the latest WM6.1 builds.
EDIT:
Normally I'd flame you for this, but Im already flaming another noob atm That doesn't mean someone else wont flame you later.
Ta
Dave
pachjo said:
OK please don't flame me as I am going round and round in circles jumping from one thread link to another trying to get to grips with this stuff!
OK...
The other day I tried to install the hardspl and got the white screen problem.
I followed the thread to sort that out and all appeard ok and the phone continued to work OK under HTC stock 6.1
Yesterday I flashed L26_Kaiser_Diamond_V8_light release and have been playing around with it trying to sort stuff out.
I then started reading the thread about ultimate radios and trying to work out what other radios work with this ROM and how I go about installing them and read I need to confirm the spl I am on and so did the hold camera button and reset to see the spl version.
It says the following:
KAIS130 MFG
SPL-1.0.0liPof
CPLD-8
Now from what I understand it should say SPL-3.2X or similar?
But it does not?
I thought that I needed the SPL-3.2X etc in order to flash cooked ROMS but it looks like I dont have that......so how was I able to flask L26_Kaiser_Diamond_V8_light release ?
Thanks
Click to expand...
Click to collapse
If you are able to flash a ROM onto your device, then you must have an UNLOCKED phone. For simple instructions on upgrading to the new SPL I suggest you visit the following :
http://forum.xda-developers.com/showthread.php?t=398565&highlight=step
Good luck.
Well I am sure I am gonna get flamed for this post, but here goes....
BTW "I AM NOT MOANING OR PICKING FOR AN ARGUMENT" I know this info here is given as is and appreciate the time people spend putting it all together
For the noob there is a trillion things to read here all of which lead to another trillion things which lead to ......
This phone flashing is all new to me and as I paid £434 for it I dont want to brick it, a term along with many I have never heard of before coming here.
I digress...
Anyway after reading and trying to understand it all I have flashed my phone and it works a treat and I am happy, just still in the dark about many things.
The thing is as a noob it is extremely daunting to start to read a thread, wiki etc to try to understand about a topic which diverts you to threads which divert, divert, divert so that after 3-4 diversions you foget what it was you were readiing about to start with!
And then you get to the point....I dont understand this...should I post lest I get flamed.......
So basically from a noobs point of view....everyone was a noob at some point, be gentle with us!
OK.....let the pachjo bash commence...........
Not a flame, just my way of working...
You raise some good points about the amount of info here. But like most here I managed to flash my device without posting a single new thread. If I had a problem with a step I posted there.
_Alex_ has consolodated most info into the single sticky. And there are step by step guides and FAQs on the Wiki.
I just took it one topic at a time:
*Found a ROM, said I needed HardSPL.
*Found HardSPL, installed it.
*Flashed ROM.
*No sound, found thread explaining about Radios. Flashed Radio.
*and so on.
I was (and still do) always reading thread that I found related to me learning as I go and helping where I can. I too like you knew nothing when I first joined and no one minds "noobs" asking questions in the relevant threads when they get stuck, but this is ROM development forum. All new threads should pertain to ROM "development".
Ta
Dave
you must use (aka JumpSPL )file before changing the SPL
this jumber must be in your device before flashing the new hard SPL
see hare and read carefuly :
http://forum.xda-developers.com/showthread.php?t=396922
got it from here also
http://forum.xda-developers.com/showthread.php?t=354061
cheers
Thanks guys.....am reading away and will take onboard your comments
first off, you can flash any rom with the olipof hardspl 1.0. the problem is, you will get screen freezes every once in a while. Using jumpspl, you can go to another hardspl. Usually jumpspl is included in all the new hardspls, but maybe not. Get familiar with what jumpspl is and then switch to hardspl.
thomassster said:
first off, you can flash any rom with the olipof hardspl 1.0. the problem is, you will get screen freezes every once in a while. Using jumpspl, you can go to another hardspl. Usually jumpspl is included in all the new hardspls, but maybe not. Get familiar with what jumpspl is and then switch to hardspl.
Click to expand...
Click to collapse
Yep... I shall do that!
I have gone flash crazy as I am now gonna whack on L26_KaiserDiamond_V9
I am amazed at how fast my apps are loading now I am no longer on the stock ROM!
The phone reception is better, the SRS WOW is fandabbydosey its all good for me, and I have fixed (well found the solution to at least one of my gliches also)
How 2 Root 1.33.0006 SPL & Flash SPL || MyTouch3G / 32B Magic || Without Goldcard ||
Tutorial : Rooting the "perfect" 1.33.0006 SPL & Flashing a new SPL
Newb Difficulty Level: 5/10 (A learning android newb)
Advanced Root User Difficulty Level: EASY!
GIVE CREDIT WHEN ITS DUE!
Note to readers:
I actually found a easy fix for 1.33.0006 for 32B Magic or MYTouch3G phones
KEEP IN MIND THAT I AM USING A MERLOT MYTOUCH3G, Stock 4GB SD card & BROKEN "Market" Application SO MAKE SURE YOUR DOWNLOADING THE FILES THAT WORK BEST FOR YOUR DEVICE and I am only providing steps used to bypass the "PERFECT SPL 1.33.0006" & YOUR RESPONSIBLE FOR THE RESULT OF YOUR DEVICE!
FILES I USED:
*ADB is a MUST so make sure to watch this video to safely install ADB
(NOTE: The video is using 1.6 donut spk... the steps are the same but use the 1.5 r3 spk on the same page given on the video.)
*flashrec-20090815.apk
MAKE SURE YOU USE THIS VERSION...!
* "Rooted" Recovery Image
I am using Amon_Ra's recovery-RA-magic-v1.2.3G which in my opinion is the best as it has flashed every rom perfectly if you know what your doing but it depends on what rom you will be flashing in some cases.
* A NEW SPL!
I am currently using Engineering-SPL-HBOOT-1.33.2009-signed by Amon_RA (BIG UPs TO Amon_RA for these files) on my T-Mo MyTouch3G but it depends on your device.
NOW TO WORK!
Step One - Enable USB Debug/Development Mode:
*Load up your device till you reach your home screen. Once your device is up and running hold menu and go to settings>applications>development then enable "USB Debugging" then press home & plug the device up to your PC & DONT MOUNT.
Step Two - Install Recovery Image Loader via ADB:
*Open CMD and as the video above stated you must navigate to your ADB folder. Once that is done you should install flashrec-20090815.apk (Recovery Image Loader) though CMD by placing it on both your SDCARD & the ADB Tools Folder (For me its C:\android\tools\).
~Now type these commands within CMD:
cd c:\android\tools (press enter)
adb install flashrec-20090815.apk (press enter)
*Now you have installed Recovery Image Loader and you may now close CMD but dont restart your device
Step Three - Rooting the unrootable (Sorta):
*Now find your recovery image ( Example : Recovery-RA-Magic-v1.2.3G.img or Recovery.img). Once found rename it as "cm-recovery-1.4.img"! Save this file to the root of your SDcard & delete the "flashrec-20090815.apk". now press backup recovery image and wait till its done (quick 2secs) then erase everything but "cm-recovery-1.4.img" within the text box. Now type " /sdcard/cm-recovery-1.4.img ". Now press FLASH RECOVERY IMAGE and wait till its done. Once its done restart the device and be aware that you will lose everything that isnt saved to your google account or backed up to your PC.
SMART COMMENT: WOW DID I JUST ROOT THE UNROOTABLE? I guess I did lol
Step Four - Change SPL to Prevent this issue in the future:
*Move the SPL ( & the ROM if you want to start installing it right away ) you downloaded earlier to your SD card and delete everything else if you want. Now select "WIPE/FACTORY SETTINGS" and follow on screen instructions and then do this a additional 2 times to be safe. Now flash the SPL and once it starts to reboot on its own (after it shows the picture of a box and a device) hold the home button and then FLASH YOUR ROM
THATS IT! YOUR DONE AND YES I DID SHOW YOU HOW TO ROOT 1.33.0006 but it doesnt run properly so make sure you flashed a new SPL before flashing any new "Radio" or "ROM" images or you could brick your device.
HOPE THIS HELPED MANY WHO HAD PROBLEMS ROOTING THE DEVICE!
isn't this just the same as the one click root? cuz on the one click root you don't need adb. It just seems like you are adding necessary steps to it. Please correct me if I am wrong. I don't mean to bash your work by any means.
I don't see why no one else has congratulated you on compiling one of these for those people that might eventually NEED THIS GUIDE! Lol.
Great work. Simple.
I had the "perfected SPL" when I picked up my MT3G on the release date. Pretty unfortunate...but I rooted it like two days later. Lol.
I never got an answer in the other SPL thread so here it goes...
Can we safely go from one SPL to another?? The reason I ask is I have the problem with the blurry screen at boot but I only encountered it when I flashed a new SPL. Now I have read up on it & it looks like some people running the same ROM with different SPL's don't have the blurry screen.
Seeing how so many people had problems bricking with haykuro's DangerSPL, the SPL is something I don't wanna mess with unless I have a definate answer. So anyone wanna chime in on this?
Beast84 said:
I never got an answer in the other SPL thread so here it goes...
Can we safely go from one SPL to another?? The reason I ask is I have the problem with the blurry screen at boot but I only encountered it when I flashed a new SPL. Now I have read up on it & it looks like some people running the same ROM with different SPL's don't have the blurry screen.
Seeing how so many people had problems bricking with haykuro's DangerSPL, the SPL is something I don't wanna mess with unless I have a definate answer. So anyone wanna chime in on this?
Click to expand...
Click to collapse
yea... could i go from 2005 one to the 2009 one? any help there?
bogdi1988 said:
yea... could i go from 2005 one to the 2009 one? any help there?
Click to expand...
Click to collapse
@Everyone above (excluding Reignzone)
Lol really? okay try flashing 1.33.0006 haha
It wont be as easy as you all think
@Reignzone
Thanks
Azuske said:
@Everyone above (excluding Reignzone)
Lol really? okay try flashing 1.33.0006 haha
It wont be as easy as you all think
@Reignzone
Thanks
Click to expand...
Click to collapse
No, you are right it won't be, but if you downgrade back to cupcake, you can one click again. Anyway, nice post man. Great job.
Thanks
Thats exactly why I posted this because I had a hard time getting back to cupcake because of the spl
Hello there, thanks for the guide.
I try to follow your guide to root my HTC Magic and I have some questions.
1. I run the command "adb install flashrec-20090815.apk " and it installed the flashrec to "/data/local/tmp" directory. Is this correct?
2. I copied the recovery image to the sd card and insert into the phone. then based on you guide. I should delete the flashrec I installed while ago. But I cannot delete the file. Can you give us more details regarding this one? Thanks.
3. Sorry but I have some hard time to sollow the step three. Can you give us more details about this.
thank you and good day
Steven
To be 100% honest im not sure where it is saved... i just happened to run into a working solution at random.
I do know that the older version i tried (Recovery Image app) didnt want to install
Reignzone said:
I don't see why no one else has congratulated you on compiling one of these for those people that might eventually NEED THIS GUIDE! Lol.
.
Click to expand...
Click to collapse
Umm because it doesn't do anything. flashrec ANY VERSION does NOT work on a phone with 1.33.0006
scrufy Originally Posted by Reignzone I don't see why no one else has congratulated y for those people that might eventually NEED TH. Umm because it doesn't do anything. flashrec ANY VERSIO phone with 1.33.0006 Today 03:28 Pm. Yes it did for me. at least in cupcake.I'm not sure in donut.guess you have to downgrade to cupcake.
scrufy said:
Umm because it doesn't do anything. flashrec ANY VERSION does NOT work on a phone with 1.33.0006
Click to expand...
Click to collapse
LOL WOW he had the same problems dude and he is a developer...
Maybe you did something wrong when installing it
Azuske said:
@Everyone above (excluding Reignzone)
Lol really? okay try flashing 1.33.0006 haha
It wont be as easy as you all think
@Reignzone
Thanks
Click to expand...
Click to collapse
So basically what you're saying is you don't know?? If you don't, that's cool. But don't laugh & then not give an answer. Just makes you seem arrogant, like you feel better than us. Which, by the way, YOU AREN'T!
Beast84 said:
So basically what you're saying is you don't know?? If you don't, that's cool. But don't laugh & then not give an answer. Just makes you seem arrogant, like you feel better than us. Which, by the way, YOU AREN'T!
Click to expand...
Click to collapse
Sorry if you took it that way but that isn't what runs through my head when I laugh or anything... My bad -_-
ANYWAY I only know what I posted... I am a learning newb and I am getting better at this stuff as I go. My tutorial explains exactly what I did.
EDIT:
P.S. My smartass comment was for the people that was calling this useless just because they didn't experience this issue
Azuske said:
Sorry if you took it that way but that isn't what runs through my head when I laugh or anything... My bad -_-
ANYWAY I only know what I posted... I am a learning newb and I am getting better at this stuff as I go. My tutorial explains exactly what I did.
EDIT:
P.S. My smartass comment was for the people that was calling this useless just because they didn't experience this issue
Click to expand...
Click to collapse
Eh no hard feelings, I was just looking for a straight answer. I just wanna get rid of that damn blurry screen, thats all. Thanks for the step by step tho. I did it the easy way with one click root but I did my G1 the hard way so I know how frustrating things can get. Thanks again
i was able to flash SPL 1.33.0006
I had rooted my MYTOUCH 3G in August using the one-click method. I have been running several ROMS since then. But I never tried to flash a new SPL. However, after reading this post I decided to give it a try. I booted into recovery mode/ wiped and then flash 1.33.2009 SPL. It loaded and rebooted into recovery again. I then wiped and loaded a ROM. everything is fine.
Later I checked and I now have 1.33.2009 SPL the perfect SPL 1.33.0006 is gone.
so im on a rooted mt3g, i have been running different roms, cyan, hero, dwang, i am at dwang 1.13. so to flash the 1.33.2009 spl do i have to wipe and flash to dwang 1.12 then flash the spl then dwang 1.13?
also what are the advantages/disadvantage?
which spl should i use?
thanks
Hi
I have 1.33.0004 on my 32B Sapphire and Android 1.6. Will this method help me root my phone? If not then is there an easy way to root my phone?
Thanks in advance
before saying anything i know it should be in Q&A but no one reply me there =[[ and i really need help.
So im trying to root my buddy g1 from scratch, got NBH file and brung the stock 1.6 down to RC29, it went good than i went and download the Root.apk for faster rooting, everything went fine untill i go and upgrade the radio, did the alt L and than atl S and now the damn phone is stuck on G1 bootscreen! So im like alright ill just do a wipe, restatred the phone with the Power+Home wouldnt get into recov menu so i decided to do the RC29 wipe over, i reformat my sd card to FAT32 and than put the Dreaimg.nbh on it and do the Power+Camera but still it just stuck on G1 bootscreen, help?? Please tell me that its not bricked.
johnphamiliar said:
before saying anything i know it should be in Q&A but no one reply me there
Click to expand...
Click to collapse
THIS IS NOT AN EXCUSE TO BREAK FORUM RULES.
This thread has now been reported, and hopefully, it will be closed before someone goes against their better judgment and helps you.
If you want an answer, have patience and check back in the Q&A. Or, post in the relevant ROM thread. Or, search. Or, don't perform procedures on your buddy's phone if you don't know what you're doing. But DO NOT post in here when you KNOW it's a violation of the rules.
these guys are crawling out all over the place today....feel bad to be a mod today..lol...
you need to slow down friend and reread everything you need to and start from step 1.
If I were a mod, I would've taken the day off. It sounds bricked to me if you can't even get into fastboot. You should've done the one click root.
johnphamiliar said:
before saying anything i know it should be in Q&A but no one reply me there =[[ and i really need help.
So im trying to root my buddy g1 from scratch, got NBH file and brung the stock 1.6 down to RC29, it went good than i went and download the Root.apk for faster rooting, everything went fine untill i go and upgrade the radio, did the alt L and than atl S and now the damn phone is stuck on G1 bootscreen! So im like alright ill just do a wipe, restatred the phone with the Power+Home wouldnt get into recov menu so i decided to do the RC29 wipe over, i reformat my sd card to FAT32 and than put the Dreaimg.nbh on it and do the Power+Camera but still it just stuck on G1 bootscreen, help?? Please tell me that its not bricked.
Click to expand...
Click to collapse
Ok anyone. Mods are getting really angry with all these post. Ur probaly gonna get banned for posting in this section. Anyway u probaly didn't follow directions. You flashed the spl before u did the radio and got bricked I guess. If u can't get into the bootloader by pressing camera + power or recovery home + power. You are brick. See you in 3 days after ur banned. You should have search first
***MOD EDIT***
PLEASE READ THIS THREAD FOR UP TO DATE INFORMATION : http://forum.xda-developers.com/showthread.php?t=655097
***O.P. EDIT***
The link above does contain some more detailed information but the guide below has yet to cause a brick.
IF YOU PLAN TO FLASH THIS SPL PLEASE READ THIS WHOLE POST
This is for the Dream/G1 ONLY. If you have a Sapphire/MT3G this SPL is not needed.
If you have no idea what a SPL is or you are looking for info on other SPLs please read this page http://code.google.com/p/android-roms/wiki/SPL
Let me start off by saying that I have nothing to do with the actual development of the SPL. I also take no responsibility if you do decide to flash this SPL and brick your phone. That being said I decided to create a "How To" for the SPL for the simple fact that I would have switched to it long ago if I knew how easy and safe it was.
The SPL that you need for many of the new Eclair ROMs along with Hero ROMs and some Donut ROMs like Super D is a special SPL created by Haykuro that basically gives you more space to flash larger ROMs. When Haykuro first released the SPL there were reports of people bricking their phones. It turned out that the reason for the SPL causing a brick was because the SPL needed to be flashed over the latest radio and requires a PVT board. If the SPL is flashed over a radio version prior to "2.22.19.26I" or on a DVT board it will cause a brick. After people heard about this SPL causing bricks it became known as the Danger or Death SPL because of the danger that it can cause death to a G1.
A lot of people including my self were very worried about flashing the SPL in fear of a bricked phone. The result being many people not wanting to flash certain ROMs because they do not want to brick their phone. Some devs have actually changed their ROMs just to make them small enough to flash with out the Danger SPL so that more people will use their ROM.
Well if you are reading this and you don't have the Danger SPL because of the fear of a brick well then don't worry its ok to be scared but this "How To" will get you through it safe and sound.
IMPORTANT: Before going any further make sure that you have PVT board. You can do this by rebooting your phone and holding the camera button. The first line should say "PVT" if you see "DVT" then DO NOT flash this because odds are you will get a brick but If it says "PVT" then you are good to go.
First you are going to need to download the latest radio and the SPL. both can be found here http://code.google.com/p/sapphire-port-dream/ There is also a new radio that is compatible that can be found here http://forum.xda-developers.com/showthread.php?t=640535
Prior to starting the installation process please make sure that your battery has a good charge. Also DO NOT pull your battery out at anytime during the installation process. I know it seems like common sense but I read a thread where someone had pulled their battery in the middle of the installation process and they ended up with a brick.
Now that all that's out of the way lets get started!
1. Copy "ota-radio-2_22_19_26I.zip" or "G1-radio-2_22_23_02.zip" and "spl-signed.zip" onto the root of your SD card.
2. Reboot into recovery. I suggest using the RA-dream recovery you can download it here http://forum.xda-developers.com/showthread.php?t=566669
3. Wipe your phone "factory data reset" (this step isnt really necessary since your phone is wiped after flashing the SPL but I always like to wipe before flashing anything)
DO NOT SKIP THIS NEXT STEP OR YOU WILL BRICK YOUR PHONE
You must have the latest radio "2_22_19_26I" or "2_22_23_02" to flash this SPL if you already have the latest radio you should not have to flash it again but it will not hurt if you do flash it again. When in doubt flash it anyway.
4. Flash the Radio "ota-radio-2_22_19_26I.zip" or "G1-radio-2_22_23_02.zip" it will install and then it will ask you to reboot to finish the installation, so reboot, it will then finish installing and then reboot back into recovery.
5. Flash the SPL "spl-signed.zip" it will install and then ask you to reboot to finish the installation, so reboot, it will then finish installing and reboot into recovery so you can flash your ROM
A simple way to make sure that the SPL flashed correctly is when you reboot to the boot loader screen by holding the camera button you will see HBOOT-1.33.2005. You can also see that it flashed correctly by checking your system size it will now be 89mb a very easy was to check this is with the My Account app available in the Market.
Great idea to post this again, since so many people are asking about it.
I flashed mine way back when Haykuro first posted it, and I seem to remember that you had to have a PVT board as well. Is this still the case? I can't remember whether or not anyone found out otherwise.
kathi17 said:
Great idea to post this again, since so many people are asking about it.
I flashed mine way back when Haykuro first posted it, and I seem to remember that you had to have a PVT board as well. Is this still the case? I can't remember whether or not anyone found out otherwise.
Click to expand...
Click to collapse
PVT = a must have.
Also forgot to mention that when you reboot after flashing the SPL, you have to reboot with Home+Back
kathi17 said:
Great idea to post this again, since so many people are asking about it.
I flashed mine way back when Haykuro first posted it, and I seem to remember that you had to have a PVT board as well. Is this still the case? I can't remember whether or not anyone found out otherwise.
Click to expand...
Click to collapse
Yeah thats a big reason I decided to post this, so many ROMs now say they require Death/Danger SPL and only a couple actually provide a link or some type of simple instructions. I figure with a dedicated "How To" we can eliminate questions about the SPL in ROM threads and make people feel a little more comfortable with flashing it. I dont believe anyone actually tested it without a PVT board. I havent even seen anyone one here that doesnt have PVT board. Just in case though I will edit the OP, thanks for remembering that because I completely forgot that it has only been tested on a PVT board as far as I know.
also you should include how to know which spl you have. i was about to flash the danger spl again because i forgot i already had it
xsnipuhx said:
PVT = a must have.
Also forgot to mention that when you reboot after flashing the SPL, you have to reboot with Home+Back
Click to expand...
Click to collapse
I rebooted with the reboot option in the recovery with out an issue.
Joe333x said:
I dont believe anyone actually tested it without a PVT board. I havent even seen anyone one here that doesnt have PVT board. Just in case though I will edit the OP, thanks for remembering that because I completely forgot that it has only been tested on a PVT board as far as I know.
Click to expand...
Click to collapse
If I remember right, some people flashed the radio first, and still bricked, and the difference was that they didn't have a PVT board.
Maybe you should also put in big red letters at the beginning about flashing the radio first. You can tell by reading all the questions on here that at least half of the people don't read the instructions, they just flash away in any order they feel like flashing!
kathi17 said:
If I remember right, some people flashed the radio first, and still bricked, and the difference was that they didn't have a PVT board.
Maybe you should also put in big red letters at the beginning about flashing the radio first. You can tell by reading all the questions on here that at least half of the people don't read the instructions, they just flash away in any order they feel like flashing!
Click to expand...
Click to collapse
Very true red letter warning has been added.
Please if anyone has suggestions for this "How To". Dont hesitate to post. I made this to help people out so if you have an idea that will help let me know.
When I first got a G1 as a test phone I tried to flash the radio/spl and it failed repeatedly. I'll try it again as I have had the phone for awhile and I want to try some of the newer ROMs
EDIT: Still getting fails on the radio flash.
it says:
Install from sdcard
Finding update package
Opening update package
E: Can't open /sdcard/ota-radio-2_22_19_26I.zip (bad)
Installation aborted
could it be my sd card?
It looks good now!
I remembered right:
Ok if u press the camera button + power to power the phone up and if u see "PVT" then ur good to go if u see "DVT-1 or 2" then u should defenetly not flash cuz almost every1 with dvt gets "bricked".
Click to expand...
Click to collapse
form this thread:
http://forum.xda-developers.com/showthread.php?t=517593&page=9
So, where can I get the Haykuro/ Death SPL ? Do it same way like Danger SPL ?
MaDaFGG said:
So, where can I get the Haykuro/ Death SPL ? Do it same way like Danger SPL ?
Click to expand...
Click to collapse
The Haykuro/Death SPL IS the Danger SPL.
MaDaFGG said:
So, where can I get the Haykuro/ Death SPL ? Do it same way like Danger SPL ?
Click to expand...
Click to collapse
it is called Haykuro SP: .2005 you guys have to get your facts straight.Haykuro is the person that ported the Magic's SPL to the Dream to allow larger roms to be installed.
Both the Radio & SPL are here:
http://code.google.com/p/sapphire-port-dream/
So does SPL flashing only apply to G1's? I have a mt3g. I can safely flash any rom w/o flashing an SPL first?
kathi17 said:
It looks good now!
I remembered right:
form this thread:
http://forum.xda-developers.com/showthread.php?t=517593&page=9
Click to expand...
Click to collapse
Thank for finding that I just edited it again
I'm snowed in tonight, so I'm gonna try this out. I hope everything I need to know is here. If I do a Nandroid+EXT backup before, will I be able to Nandroid Restore after the SPL upgrade?
So I tried to flash the spl yesterday cuz i wanted to try out some new roms, but I kept on getting errors everytime I flashed the spl and it aborted. So after a while i just gave up and went back to cyanogen. Does anybody know why there would be errors when installing the spl. and yes I did flash the radio first.
rizocreations said:
So does SPL flashing only apply to G1's? I have a mt3g. I can safely flash any rom w/o flashing an SPL first?
Click to expand...
Click to collapse
That is correct. This SPL actually is the one that if for your mt3g but edited for the G1 so that it can flash larger ROMs.
rizocreations said:
So does SPL flashing only apply to G1's? I have a mt3g. I can safely flash any rom w/o flashing an SPL first?
Click to expand...
Click to collapse
Its called Sapphire to dream port for a reason.You can use the .2004 or .2010 SPL or whatever its called instead.
If I already have the correct radio, do I have to re-flash the radio again before flashing the SPL?
The reason I am asking is that I have 2 G1's.. the first I unknowingly did everything right and have the danger SPL without any problems. When I went to root the second one a couple of months later, I bricked it even though I thought I did everything right. Now my "new" phone has the correct radio, but only the engineer's SPL and I want to try some of the newer ROMs but am afraid to brick the phone again.
Thanks
First, I'm sorry if I posted this in the wrong section.
I know this is the G1 area, but need help.
Well, I was looking at some tutorials from TheUnlockr.com and they seem pretty easy on a mytouch 3G. I have successfully installed Cupcake (1.5) on my phone.
But before I do the actual rooting, I wondered if anyone would be so nice to
guide me with installing [ROM] KiNgxKxROM Sense Hybrid Version 2.3 "Back to Work We Go" <11/9/09> - xda-developers onto my mytouch.
I don't know what to do, and I've tried reading the steps but I'm completely lost.
IDK if the steps are for G1 users or mytouch. I hear all these "spl"s and "radio"s and don't know what it is.
All I want is to install that ROM on my phone. the Unlockr says to download the ROM's .zip file and simply flash it, but idk if that's exactly what's required for the above ROM.
Anyone suggest other ROM that has the HERO Sense UI?
and what's a gold card? do I need that?
and I only have a 1GB MicroSD card...idk if that's relevant, thanks so much!
*facepalm
http://forum.xda-developers.com/showthread.php?t=519523
well that link doesn't work.
All I'm basically asking is if I can just load the already downloaded "ROM" and simply dragging it to my SD card to be able to install....since it's for the G1 and idk if it's the same process as the mytouch.
DracoMalfoy said:
well that link doesn't work.
All I'm basically asking is if I can just load the already downloaded "ROM" and simply dragging it to my SD card to be able to install....since it's for the G1 and idk if it's the same process as the mytouch.
Click to expand...
Click to collapse
I beg to differ. The link does work.
You should read about spls and radios before flashing roms. Anyway, good luck.
It should work in your case....and if it doesnt....no harm done.
So you're saying that I don't need spls?
You do need an spl.
http://forum.xda-developers.com/showthread.php?t=519523
Yes, it does work. It's a link to a thread stickied in this forum. It's called ***Informative Links*** - Read before clicking "New Thread"
There is no point spoonfeeding you information because you don't *learn* and just end up following a bunch of steps without understanding what you're doing. This greatly increases your chance of doing something wrong just because someone tells you to, this can and does happen, usually unintentionally because a certain step worked for someone else but not for you because your phone can be different in a way you don't yet realise.
You haven't even told us what phone you have, let alone any technical information about it. So, go look into specific information about your handset. Learn about what SPL you have now, this will tell you if you need a goldcard or not (Magic) or whether you need to install the DangerSPL (G1) or not. SPL is very dependent on the radio installed, if you get the versions wrong you will brick your phone. Learn about recovery images and install one on the phone. Depending on ROM, you may have to partition your SD card, which you can do from recovery.
I hope that's enough of a good start for you. If not, I would suggest not taking the risk bricking your phone and just be happy with what you have.
alritewhadeva said:
You do need an spl.
Click to expand...
Click to collapse
Could you guide me through?
I'm new to this rooting stuff and when I was looking at theUnlockr videos the guy didn't mention anything about SPL, he simply said to drag the ROM into the SD card and then wipe, partition, and flash or something like that.
But since the rom im trying to install is for G1 and Mytouch I'm not sure if the same process is for both or just the G1.
Well, I have a T-Mobile MyTouch 3G with 1.5, IDK about the other stuff, but here's some info I found on my phone:
SAPPHIRE PVT 32B
HBOOT-1.33.0006
RADIO 2.22.19.261
IDK, that's it.
DracoMalfoy said:
Well, I have a T-Mobile MyTouch 3G with 1.5, IDK about the other stuff, but here's some info I found on my phone:
SAPPHIRE PVT 32B
HBOOT-1.33.0006
RADIO 2.22.19.261
IDK, that's it.
Click to expand...
Click to collapse
You will need SPL's, a swap partition, etc. etc.
Seems like you only have the stock SD card.
Your device will not even be usable on a daily basis without at least a class 4 microSDHC
Go for a basic Eclair or Donut rom first before you do some serious damage to our phone.
And there literally is a MyTouch3g section... This is a G1 section.. if you're just getting started, you're better off over there.
Oooooooo
Can I run this on sapphire? When's the next update?
I can't even believe this thread is happening....