Related
Hey guys,
Well I succeeded in upgrading to Anansky's BigStorage ROM and was very satisfied, but now my stupid speaker broke (I have a similar problem to other users where they can hear sound if they blow into the speaker). I have to return the Magician so I need to revert back. Can someone PLEASE upload the original XDA II ROM PLEASE???
Here's a list of instructions on how to backup the ROM:
Backing up your ROM can be done by connecting your Magician to the PC through the data cable when you first uncheck the USB connection of active sync.
If your Magician connects with active sync because you didn't uncheck the USB connection in the active sync connection settings then you will not be able to backup your ROM to an SD memory card.
1. Before connecting your Magician you should bring it into the boot loader mode. This can be done by simultaneously pressing power + camera buttons and at the same time the soft reset button with the stylus.
2. After connecting your Magician to the PC through the USB in boot loader mode and having your SD card inserted into the MDA, you run romupdate.exe.
3. Then choose the USB connection in the connection settings of romupdate.exe window and click on ok. After that a terminal window will popup in that window.
4. Type d2s and press enter. Your Magician will start copying the ROM to the sd card. The screen of your Magician will be dark (no light), but you will see it counting up to 100%. When it reaches 100% it will say it is calculating the checksum. Give it some time till its done and it will say checksum ok.
5. After finishing the transfer of the ROM from your Magician to the SD card, put your SD card into an SD card reader connected to your pc. Your pc might pop up a warning message that says your SD Card is not formatted would you like to format? Click No and open a Command prompt (DOS) window.
6. Change directory to your root directory (cd c:\) and run the command ntrw read o2orig.nb1 x: where x is the drive letter of your sd card. That command will create the ROM Backup file of your ROM into your C drive root directory by the name of o2orig.nb1. Make sure you keep o2orig.nb1 in a safe place and use a copy of that file for the rest of the procedure. Note that after finishing the copy from your SD card to o2orig.nb1 file ntrw might give you an error, just don’t pay attention to it.
7. WinRAR the o2orig.nb1 file, then upload it to the XDA Developers FTP .[/i]
No one wants to help?
The question is why havent you got a backup?? You were told to do this in the first instance should anything go wrong!!
somebody apparently has uploaded the O2 mini original rom, check it out!
The answer to this was I was using my digital camera as an SD reader...and the backup didn't work properly for some reason. So now I have nothing.
The backup (I think you're talking about the O2 Original Dump Rom) doesn't work for me. I have a 1.11 version of the O2 Asia ROM, but I'd rather have the original WWE. Oh yes, and I've tried several times with the "Original Dump Rom" using 220, 415 and 416 bytes...nothing works.
This may work for you - use the romupdate software to get the rom image of your device to the sd card. By this stage you have an edited rom image on the pc. Use ntrw to write that image over the top of the sd card that you have just written to with romupdate. Then plug it into the ppc. Do not format the sd card in the immediate procedure at anytime. For whatever reason I think the romupdate software puts a format on the sd card which the ppc recognises. There were a number of errors on the ppc screen just after installation however when you push the reset button hey hey the original splash screen boots up. Prior to this check that the edited rom header is 416, in my efforts it was not 415. The RomMiniOrg.nb1 image was good with the only NON change being the radio which remained at version 1.11 but I downgraded it to 1.05. I don't think the service centre will worry to much about this should you need it. Goodluck with this, it worked for me.
Hi yozhek,
Thanks for the help. I did what you said but it still didn't work. However, I used O2_mini_asia from the FTP to downgrade my extended rom, protocol and rom version...then I found the Radio downgrade on the FTP and downgraded to version 1.01.
now everything is original!
I didn't know that the Nb1 files did not include the radio stack downgrade so I had to downgrade that seperately.
the command in the romupdate program basically determine which image to backup.
d2s for rom, but I am not sure what's the other command for extended rom and radio. Anybody?
Can I use MaUpgradeUt_noID.exe to change the ROM on my mini with the o2mini_asia.nb1 ?
miniuser: no
you will have to use the process as described in procedure.doc (available in the FTP under anansky's bigstorage folder)
I did as described in the procedure.doc. I have run this command
ntrw write o2mini_asia.nb1 e: and then inserted the SD card into my mini and pressed the power+camera+soft reset button
but it is not doing anything, it has stopped at "Serial" above and v1.00 below for an hour now. Any suggestions?
cheers
mini_user
I tried it second time, now it says
SD DOWNLOAD
==========
SECTIONS=1
Not Allow Update
Any Suggestions?
Cheers
Sorry for the last post, was trying out something else.
I am using a 256MB SD card and the size of the rom is only 127MB after ntrw, does it make any diff??
you can always ntrw write a 127mb rom image into a 256mb sd card.
the rom flash will not work (and hence the no update allowed message) if your rom image in your sd card is invalid for some reason. I make a bobo previously, trying to copy 416byte of anasky rom into my original rom, instead of the other way round. And it give me that error message. After realising my mistake, and did the right modification, the flash went through successfully. so double check your rom header edit if you are not able to proceed to the flash step.
I have a mini with qteck 1.11.00 WWE
and I have download the o2mini rom from xda ftp and have got a 256 mb card
if I want to flash my mini with the o2mini rom the are these the steps to follow
1. dump qtek rom into card
2. copy it to pc
3. copy 1st 416 bytes of qtck into o2mini rom
4. dump o2mini rom into card
5. put mini into bootloader mode
6 update with mini rom
cheers
zenkinz said:
somebody apparently has uploaded the O2 mini original rom, check it out!
Click to expand...
Click to collapse
where is the file?
I've upgraded to the latest 1.11 ROM, I now want to revert back to the original ROM (T-mobile UK).
I took a back-up of the rom onto the SD card, and backed up using ntrw.
However, writing the back-up file back to the SD works, but, the device will not boot from the sd card. I do the following:
- disable USB activesynch
- insert usb cable
- press camera/power and reset
- goes into boot loader, and says USB.
Does not prompt to install rom from sd card.
I've tried it without the usb plugged in, the screen says Serial and does not prompt for rom installation.
Same problem if I use the downloaded tmobile.nb1 from the ftp site.
What am I doing wrong? Is there any other way of reverting back?
Saquib
If you are returning the phone for warranty purposes please ignore the following:
Why on earth would you want to go back?
If you want all the t-mobile customisations, why not just install the bigstorage and load up the t-mobile extended rom.
You guessed right - I want to return.
Any ideas on why it will not boot the rom of the sd?
Thanks!
i've been trying to update my tilt's rom and I don't know what im doin wrong. i've tried flashing mbarvian's solace v 1.5 rom and revrom v8 (sorry I can't remember who cooked the rom) and neither is working.
i've followed every step in the sticky for noobs like me. but when I get to step 3, which is flashing hardspl, I get lost. I moved the jumpspl files to my phone and ran jumpspl 1.93, since 1.53 seems to do nothing. it goes into bootloader, I disconnect usb, reconnect it, and try to run kaisercustomruu so I can flash hardspl 3.29. but when I try to run kaisercustomruu it just shuts down my computer. I don't know whts going on. it seems like im the only one running into this problem. i've spent the past 3 days searching the forums for a solution or reason why kaisercustomruu shuts down my comp and I can't find anything.
when I downloaded mbarvians solace rom there was another update utility that was included in the fil so I ran that. it worked, I clicked all necessary boxes, and the update initialized. but it just stays at 0 percent, and eventually gives me error 262 "update utility error" or something like that.
I tried restarting my comp and even hard reset my device. nothing is working.
im currently running the HTC windows 6.1 rom (the one straight off the site) and have hardspl 3.56.
the reason im trying to go to hardspl 3.29 is because mbarvian and the majority of people on his thread that had succes with his rom are running 3.29.
PLEASE HELP!!!
Well, you can't flash custom ROM's till you HardSPL your Tilt/Kaiser.
I noticed you didn't mention anything about disableling USB Connections in ACtive Sync/WMDC. Did you do that?
Also, kaisercustomruu is generic. Try copying the one from the ROM dl into the HardSPL dl folder. Another suggestion is do a search for flashing hardspl from sd card.
Why not use the sticky and then ask in the relevant thread? "The Sticky"
Flashing Your First Kaiser Rom (For Noobs) Read, Read & Read again, take in small steps & follow the directions to a T
stylez said:
Why not use the sticky and then ask in the relevant thread? "The Sticky"
Flashing Your First Kaiser Rom (For Noobs) Read, Read & Read again, take in small steps & follow the directions to a T
Click to expand...
Click to collapse
You will definitely get more help in that thread. But you already have hardspl, so read the part about flashing cmonex's 3.29 from your SD card, that looks like that will solve your problems.
denco7 said:
You will definitely get more help in that thread. But you already have hardspl, so read the part about flashing cmonex's 3.29 from your SD card, that looks like that will solve your problems.
Click to expand...
Click to collapse
I was going to agree with this, but then I read the flashing guide, and it says flashing from the SD card only works if you're upgrading. From the sounds of it, he doesn't have HardSPL on his phone, otherwise the cooked ROMs would flash.
To the OP, I would try another KaiserCustomRUU.exe. Just copy it from one of the custom ROMs you've downloaded and paste it into the folder you have HardSPL in. Be sure to delete the one that came with HardSPL first. If that doesn't work, maybe you could try a different computer? I don't think you need an ActiveSync connection to flash since JumpSPL puts the phone into flash mode. (Someone correct me on this if I'm wrong.) Just download HardSPL, extract, run JumpSPL, plug your phone in, and run KaiserCustomRUU.exe. It should flash!
I do have hardspl installed its v3.56. I just wanna try 3.29 cos mbarvian and the people on his rom thread that had success with his rom have 3.29 installed.
I read the flashing for noobs sticky and i've been following it verbatim. when I went to try and format my SD card to fat32 it wouldn't let me. I used resco explorer and when I tried to format it it said it wasn't unlocked. that's one thing I failed to ask about in my original post: how do I unlock the SD card?
I used 2 other kaisercustomruu's from other roms and they all forced my comp to shut down. I even ran it on my gf's comp and it shut hers down too.
help!
poppinpengawen said:
how do I unlock the SD card?
Click to expand...
Click to collapse
Take your microsd card and place it into the converter (normal sized sd card). There is a switch on the side. Place the switch in the opposite position of "lock"
poppinpengawen said:
I used 2 other kaisercustomruu's from other roms and they all forced my comp to shut down. I even ran it on my gf's comp and it shut hers down too.
help!
Click to expand...
Click to collapse
It sounds like you do not have kaisercustomruu in a folder, which contains .nbh file. Rather you are probably attempting to run it from your desktop???
poppinpengawen said:
I do have hardspl installed its v3.56. I just wanna try 3.29 cos mbarvian and the people on his rom thread that had success with his rom have 3.29 installed.
I read the flashing for noobs sticky and i've been following it verbatim. when I went to try and format my SD card to fat32 it wouldn't let me. I used resco explorer and when I tried to format it it said it wasn't unlocked. that's one thing I failed to ask about in my original post: how do I unlock the SD card?
I used 2 other kaisercustomruu's from other roms and they all forced my comp to shut down. I even ran it on my gf's comp and it shut hers down too.
help!
Click to expand...
Click to collapse
Ah, you have to use a SD Card reader on a PC to format it, not through the phone.
each time I ran kaisercustomruu it was in a folder with an nbh file. does it have to be by itself with the nbh file? just kaisercustomruu and the rom file?
oh that's all I have to do? just put it in the SD adapter and flip the switch? does it have to be in a computer for it to work?
poppinpengawen said:
each time I ran kaisercustomruu it was in a folder with an nbh file. does it have to be by itself with the nbh file? just kaisercustomruu and the rom file?
oh that's all I have to do? just put it in the SD adapter and flip the switch? does it have to be in a computer for it to work?
Click to expand...
Click to collapse
No.... there is nothing wrong with your SD card.
Do this:
1. Remove your SD card and your SIM Card. Start your device.
2. Connect your Device to your PC Via ActiveSync. Make sure you are fully connected.
3. Unzip and copy the exe file of attached JumpSPL to your device memory.
4. Run Jump/Soft SPL on your device
5. Wait for the bootloader screen to appear and "USB" to show.
6. Right-click activesync icon on the PC tray, go into connection settings and ensure Allow USB Connections is unchecked
7. Unplug your device from the USB port, wait 5 - 20 seconds, plug it back in.
8. Run KaiserCustomRUU.exe of the desired HardSPL and flash HardSPL3.29
To see if you have successfully flashed the 3.29 HardSPL press the camera and power button and press the soft reset once all at the same time, you will see the four color screen and it should display the SPL version.
Whether your SD card is locked or unlocked has no barrier on flashing SPL on your device, since you need to have it out of the device when you perform the SPL install.
Fat32 sometimes would not allow operation of certain files on your PC. thats why sometimes PPC programs or files would not open on your PC and would give you error msgs. Now some folks tried to create a virtual fat32 folder that could in some instances open or run fat32 programs that are created for mobile devices, but in most cases that would crash your PC OS and shuts it down. Same story with netCF files.
So in essence if you were to follow my instructions above, you will get it done and it should not take longer that two minutes to complete the process.
Again.... DO NOT SHORTCUT THE INSTRUCTIONS.
Good luck
asfoor said:
No.... there is nothing wrong with your SD card.
Do this:
1. Remove your SD card and your SIM Card. Start your device.
2. Connect your Device to your PC Via ActiveSync. Make sure you are fully connected.
3. Unzip and copy the exe file of attached JumpSPL to your device memory.
4. Run Jump/Soft SPL on your device
5. Wait for the bootloader screen to appear and "USB" to show.
6. Right-click activesync icon on the PC tray, go into connection settings and ensure Allow USB Connections is unchecked
7. Unplug your device from the USB port, wait 5 - 20 seconds, plug it back in.
8. Run KaiserCustomRUU.exe of the desired HardSPL and flash HardSPL3.29
To see if you have successfully flashed the 3.29 HardSPL press the camera and power button and press the soft reset once all at the same time, you will see the four color screen and it should display the SPL version.
Click to expand...
Click to collapse
I did do all that. like I said I followed the instructions to a tee, but when I ran the kaisercustomruu that was included with the hardspl file my comp just shut down.
question: if I run jumpspl and then use the htc update utility to flash hardspl, would that work? (the htc update utility is the update utility that worked when I tried to flash the rom but it just sat at 0%)
asfoor said:
Whether your SD card is locked or unlocked has no barrier on flashing SPL on your device, since you need to have it out of the device when you perform the SPL install.
Fat32 sometimes would not allow operation of certain files on your PC. thats why sometimes PPC programs or files would not open on your PC and would give you error msgs. Now some folks tried to create a virtual fat32 folder that could in some instances open or run fat32 programs that are created for mobile devices, but in most cases that would crash your PC OS and shuts it down. Same story with netCF files.
So in essence if you were to follow my instructions above, you will get it done and it should not take longer that two minutes to complete the process.
Again.... DO NOT SHORTCUT THE INSTRUCTIONS.
Good luck
Click to expand...
Click to collapse
but in the sticky it says that in order to change to cmonex's 3.29 i'd have to flash via SD card. that's why I was wondering how to format it to fat32. but i'll try to do it again and see if it works this time. thanks for the files
my sandisk 8g micro sdhc won't let me delete files, ad files, or even reformat the card
poppinpengawen said:
but in the sticky it says that in order to change to cmonex's 3.29 i'd have to flash via SD card. that's why I was wondering how to format it to fat32. but i'll try to do it again and see if it works this time. thanks for the files
Click to expand...
Click to collapse
can't you read? Why are you doing Cmonex? JUST FOLLOW MY INSTRUCTIONS. hardSPL3.29 is same protocol on both CMONEX and POF and whoever tells otherwise is full of BS. Again.... just follow my instructions..
msd24200 said:
my sandisk 8g micro sdhc won't let me delete files, ad files, or even reformat the card
Click to expand...
Click to collapse
Are you trying to add files to your card by inserting it into your laptop using an adapter?
BTW certain adapters for some reason or another will not allow you to do that after the SD card has been placed and used in a phone.
Can you access the SD card through ActiveSync? If you have installed programs on your SD card and you are trying to delete them from the SD card it would not let you as there is a shared violation in that process. The way to do is that you would need to remove the programs first from your device by using the Remove prompt in your settings page on your phone, then going to your SD card and deleting the program files. If you do it in the reverse order you will run into problems; Remnants of those programs will still reside in your main memory.
The attached is a utility that would help format SD card. DO NOT UNZIP IT. Just create a folder on your PC and save the attached in it, When done, change the file type of the attached file from zip to exe. Then right hand click it and do the extract to the folder you created. Follow the included instructions to format the SD card.
poppinpengawen said:
I did do all that. like I said I followed the instructions to a tee, but when I ran the kaisercustomruu that was included with the hardspl file my comp just shut down.
question: if I run jumpspl and then use the htc update utility to flash hardspl, would that work? (the htc update utility is the update utility that worked when I tried to flash the rom but it just sat at 0%)
Click to expand...
Click to collapse
Wait a second..... Do you have your device CID unlocked? In other words, did you unlock your device using one of the methods in the stickies? I am NOt talking about SPL .... Were you able to flash a cooked ROM on your device?
asfoor said:
Are you trying to add files to your card by inserting it into your laptop using an adapter?
BTW certain adapters for some reason or another will not allow you to do that after the SD card has been placed and used in a phone.
Can you access the SD card through ActiveSync? If you have installed programs on your SD card and you are trying to delete them from the SD card it would not let you as there is a shared violation in that process. The way to do is that you would need to remove the programs first from your device by using the Remove prompt in your settings page on your phone, then going to your SD card and deleting the program files. If you do it in the reverse order you will run into problems; Remnants of those programs will still reside in your main memory.
The attached is a utility that would help format SD card. DO NOT UNZIP IT. Just create a folder on your PC and save the attached in it, When done, change the file type of the attached file from zip to exe. Then right hand click it and do the extract to the folder you created. Follow the included instructions to format the SD card.
Click to expand...
Click to collapse
yeah i've tried adding/deleting pics, vids, music, etc... with phone and pc and neither works, up until a couple weeks ago i was moving pics/vids to and from the card with the ppc and the pc with no problems. i have used several different card adapters in case one was bad but no matter what i have done, nothing has worked. i already even tried the file you sent and couldn't get the sdformatter to work either. i haven't installed any aps to the card only save pics and all on there, keep my fav program cabs on there as well.
msd24200 said:
yeah i've tried adding/deleting pics, vids, music, etc... with phone and pc and neither works, up until a couple weeks ago i was moving pics/vids to and from the card with the ppc and the pc with no problems. i have used several different card adapters in case one was bad but no matter what i have done, nothing has worked. i already even tried the file you sent and couldn't get the sdformatter to work either. i haven't installed any aps to the card only save pics and all on there, keep my fav program cabs on there as well.
Click to expand...
Click to collapse
Sounds to me your 8GB SDHC Card failed if it worked before and isn't anymore. Can you play the music on the card from either your PC or Kaiser?
going crazy
so i've been following asfoor's advice. I ran kaiserunlocker, but none of the steps made any progress. I tried using it to flash spl3.29, but my spl still shows 3.56. I tried flashing the patched radio, but its still the same (1.65.21.18). I downloaded v2.0, so I know I have the most recent version of kaiserunlocker. help! im getting more and more frustrated.
Hi, I've just bought a MAC, and I want to Flash to a new ROM with the MAC.
And to flash a new rom you need a stable connection via ActiveSync or WMDC.
How do I get this same stable connection on mac. (Without installing Windows OS on Mac!)
Thanks.
(I did search, sorry if I did it wrong )
http://www.google.dk/search?source=ig&hl=da&rlz=&q=pocketpc+mac+sync&btnG=Google-søgning&aq=f&oq=
he said to flash a new rom. and for gsm phones if you have hardspl you can copy rom files to an sd card and just flash the phone without a computer. i dunno how it works with cdma (sprint/verizon). htc rom tools and activesync is a windows only deal. if you can do sd card flash thatll be your bet.
The Jack of Clubs said:
he said to flash a new rom. and for gsm phones if you have hardspl you can copy rom files to an sd card and just flash the phone without a computer. i dunno how it works with cdma (sprint/verizon). htc rom tools and activesync is a windows only deal. if you can do sd card flash thatll be your bet.
Click to expand...
Click to collapse
Something free out there?
Also, this Flash from SD.. How does that work?
I recently got a macbook for my birthday and had the same problem. The best solution I've found so far is to use the SD card to flash. I've been doing that for a little over 2 months now without any issues at all (except for syncing contacts/calendar, but SyncMate solved that problem), and have heard rumors that if you run windows in bootcamp you can flash that way too, but I haven't tried that option yet.
see this post for the flashing guide
http://forum.xda-developers.com/showthread.php?t=448008
see this post for SyncMate (trial/demo should cover basic syncing needs)
http://mac.eltima.com/sync-mac.html
Thanks! I've never noticed that Flashing from SD card column.! Thnks
i know you said you don't want to install Windows but thats what i did and have been doing for a while
I have windows 7 currently installed via VMware's Fusion and haven't had a single issue. Can flash roms, install apps, sync with outlook, etc.
I have windows7 on my pc, and when i try to install Rom it just says img not found... Same if i just copy it onto the sd(via usb transfer if it matters)
super2 said:
I have windows7 on my pc, and when i try to install Rom it just says img not found... Same if i just copy it onto the sd(via usb transfer if it matters)
Click to expand...
Click to collapse
If you could give more information about the complete process that you have done, it would be easier for someone to help you.
For example, what is the name of the ROM?
How are you decompressing it?
Are you trying to flash via WMDC or SD Card?
I am also running Windows 7 on my computer and have no trouble at all.
I think it may be something to do with the process you are doing.
Let us know what it is. I'm sure we'll be able to help in some way.
For example, what is the name of the ROM?
How are you decompressing it?
Are you trying to flash via WMDC or SD Card?
It is http_://forum.xda-developers.com/showthread.php?t=536751 this one and i already have installed max sense on the phone, and what to change it tolower ram usage and etc... Tried titantium and sense 2.1 no success. I tried via the usb connection. but cannot locate a device, after it is being rebooted. And then i tried to transfer the divimg.nbh to the sd card and reboot, no success - no image found.
one thing is clear: if you try to install the rom from sd card, your Rom name ("divimg....") is wrong. It should be something like "raphimg.nbh".
How do you establish connection between PC and your TP? There are reported some difficulties connecting your TP with the PC via Windows 7 using device center. Using the search may help...
good luck
Please post [Q] in general section.
borisku said:
one thing is clear: if you try to install the rom from sd card, your Rom name ("divimg....") is wrong. It should be something like "raphimg.nbh".
How do you establish connection between PC and your TP? There are reported some difficulties connecting your TP with the PC via Windows 7 using device center. Using the search may help...
good luck
Click to expand...
Click to collapse
I see, that should be the problem, thank you. Yes i am using the device center.
Divimg.nbh? Where'd you come up with that, lol?
It needs to be named RAPHIMG.nbh. Make sure the extension is correct, and you don't have RAPHIMG.nbh.nbh, or something like that. And the card has to be formatted to FAT32, and the image must be on the root of the card. That's all there is to it. You also need to have hard spl.
It worked just with the normal file.
same problem
Hi there...
I try to flash the new rom on my TP, and:
1) HardSPL is done, I flash one time a month ..
2) via SD card is written: Image not found - card has been formatted to FAT32, name of the image IS RAPHIMG.nbh.
3) via USB installation goes to the installation screen where "Image not found" is written also ... Active sync has been made, I've checked, that "USB support" is OK.
I have placed ROM and the *.exe file into one folder ..
Can anyone help me?
EDIT: Win XP Prof. 32BIT, Touch Pro and the ROM is ENERGY 23699 Sencity/Touch of Glass - tried both of them.