Related
Hello everyone,
I'm totally lost in this WM6 upgrade.
I've tried everything but i wont get my MDA Vario to flash with WM6.
My MDA Vario is unlocked (sim and CID) but i can't flash it because of my SPL 2.21????
This is what i have done:
installed button's 1.05 ROM
Download & installed lokiwiz - HTC Wizard Unlocker UPDATE Version 0.2b.
But stil my SPL is at 2.21.
Can someone please help me out here??
Thanks in advance!
Regards,
Schmia
Both your IPL and your SPL must be 2.xx and higher. After you flashed to Buttons rom. did you reflash to a higher version after after you unlocked and cid unlocked your phone to make sure both IPL and SPL were 2.xx or higher?
I've followed the tutorial:
16. Watch the rebooting of your PDA, if BOTH IPL and SPL are 1.xx then great. Quite probably your IPL will be 1.xx and your SPL will be 2.xx. Rerun the button 1.05 ROM downgrade a second time and it will become 1.x on both IPL and SPL. You don't need to redo the unlocking.
17. My suggestion, take for what it's worth, is to download and install the T-Mobile 2.26 ROM
This will give you a strong 2.26 IPL and SPL to work with.
My IPL was 1.XX after the 1.05 downgrade, but my SPL was still 2.21 even after the rerun.
I have tried to instal T-Mobile 2.26 rom, but it gave an error.
check if you have G3 or G4 unit
I have a 3G device.
Is there nobody who can help me???
schmia said:
Is there nobody who can help me???
Click to expand...
Click to collapse
I think that you haven't unlocked the phone properly. Read Dr. P's tutorial about unlocking G3 phones.
Kirby
if your ipl is 1.05 and your spl is still 2.21...then you need to reflash again so that both ipl and spl are 1.05 before you can proceed. ipl and spl should never be different.
WHen you downgrade to the Button rom, in most cases the IPL will change, but the SPL will not. You then have to downgrade again to get the SPL to get to 1.xx . There have been some cases reported where it takes reflahsing the button rom many times (like 8 times or somesuch) before the SPL will finally come down, but you have to complete this step or you will not be CID Unlocked.
Make sure you have your SD card out when you are flashing as this can cause problems.
Good luck, and sorry, but for those that have run into the stuck SPL there hasn't been a real solution other than keep flashing the button rom until it drops down to 1.xx. After that then the CID unlock will be complete and you can then flash the T-Mobile 2.26 rom (or whatever other 2.xx rom you want).
mfrazzz said:
WHen you downgrade to the Button rom, in most cases the IPL will change, but the SPL will not. You then have to downgrade again to get the SPL to get to 1.xx . There have been some cases reported where it takes reflahsing the button rom many times (like 8 times or somesuch) before the SPL will finally come down, but you have to complete this step or you will not be CID Unlocked.
Make sure you have your SD card out when you are flashing as this can cause problems.
Good luck, and sorry, but for those that have run into the stuck SPL there hasn't been a real solution other than keep flashing the button rom until it drops down to 1.xx. After that then the CID unlock will be complete and you can then flash the T-Mobile 2.26 rom (or whatever other 2.xx rom you want).
Click to expand...
Click to collapse
This should be added to the tutorials about Unlocking & Rom Upgrading.
And this quote also.
"if your ipl is 1.05 and your spl is still 2.21...then you need to reflash again so that both ipl and spl are 1.05 before you can proceed. ipl and spl should never be different."
Cing 8125 said:
This should be added to the tutorials about Unlocking & Rom Upgrading.
And this quote also.
"if your ipl is 1.05 and your spl is still 2.21...then you need to reflash again so that both ipl and spl are 1.05 before you can proceed. ipl and spl should never be different."
Click to expand...
Click to collapse
The Dr. P tutorial specifically says this (just not in those words). It tells you (after the last lokiwiz) to watch your screen and that you most likely will still have an SPL of 2.xx and will need to reflash (most people just don't read this and try to move on). The part of about having to reflash numerous times is new though. I've only heard of it a few times, but if you look at the posts from a month or so agao in the Dr P thread on unlocking you'll see where a few people ran into it and it took numerous flashes to finally get SPL to go to 1.xx.
before wm6 roms, every time there was a new rom for wm5 (molski or faria) you'd always get people in the thread mentioning that their ipl and spl are different. in those threads, the advice has always been to reflash a few extra times too. (I personally haven't had any problems with this...but i think i started my unlocking on a 1.8 us t-mobile rom with xelencin's rom...which had an unlocker built into the rom update package).
anyway, the phone's not bricked or anything, so you just have to keep flashing to get it working...
xelencin's rom (the first rom I ever flashed...)
http://forum.xda-developers.com/showthread.php?t=274205&highlight=xelencin
monkey_knight said:
if your ipl is 1.05 and your spl is still 2.21...then you need to reflash again so that both ipl and spl are 1.05 before you can proceed. ipl and spl should never be different.
Click to expand...
Click to collapse
I've re-flashed 3 times but if i understand correct, than i have to retry flashing until SPL and IPL are the same?
Regards,
Schmia
schmia said:
I've re-flashed 3 times but if i understand correct, than i have to retry flashing until SPL and IPL are the same?
Regards,
Schmia
Click to expand...
Click to collapse
yes. ipl and spl should both drop to 1.05. at that point you can go through the unlock and flash back up.
Thanks Guys!!!
With all your good advise, i finally have my MDA Vario flashed with a WM6 rom (TNT 2.0 Professional)
I'm really greatfull to you!
Now i have to find out what WM6 rom is the best for me.
Regards,
Schmia
i am having problems flashing some OS, and i cant even touch IPL SPL and Radio...im pretty sure i unlocked...but it might have failed...note that i have been able to do all of these things before...any assistance is appreciated
...update...
got the IPL and SPL to update just taking the .nbk and plugging it into different old OS's...tried radio in same place i pluged IPL SPL and no luck...any suggestions?...
Look at the unlocking post in Wizard Upgrading subforum, download the Button's 1.05 ROM to have IPL and SPL downgraded to 1.05, then you can unlock and flash other ROM.
However, since you are now at 3.08 IPL, it may not be easy to have SPL downgraded. Don't try to unlock if IPL is 1.01 and SPL is 3.08. Instead try to flash again until SPL downgraded
the thing is ive been able 2 flash any rom i choosed b4...and i have went threw the unlocking process before...so its not that...
also r there any roms made to b flashed on vista and xp?
Hi I have a G4 Prophet and the IPL and SPL version number reads 2.10.0001.
I would like to flash it to use a WM6.1 ROM with the touchflo type functionality and new IE Mobile features (i.e. zooming).
I have read through all the guides about carrying this out and have even started having a go but am getting confused about HardSPL.
From what I read HardSPL CID Unlocks your phone so that you can install a diffeerent Carrier (e.g. Orange, Vodaphone) ROM ... or in fact a home 'cooked' ROM off of this site.
I have tried manually carrying out the HardSPL using both the Prophet Tools GUI and the command line batch file HardSPL however after the procedure finishes my IPL and SPL do not read differently as all posts indicate (i.e. they do not read 2.G4.4PDA) ... instead they remain as 2.10.0001.
I have seen the phone go to the tri-colour bootloader screen and even the progress bar go up correctly however when it reboots it says 2.10.0001. I'm assuming that I cannot go ahead and flash with a ROM (such as the Shadow TE one until the SPL reads 2.G4.4PDA).
Can anyone offere me some help with getting to this?
Many thanks.
Nick (a very much noob!)
nisgar2k said:
Hi I have a G4 Prophet and the IPL and SPL version number reads 2.10.0001.
I would like to flash it to use a WM6.1 ROM with the touchflo type functionality and new IE Mobile features (i.e. zooming).
I have read through all the guides about carrying this out and have even started having a go but am getting confused about HardSPL.
From what I read HardSPL CID Unlocks your phone so that you can install a diffeerent Carrier (e.g. Orange, Vodaphone) ROM ... or in fact a home 'cooked' ROM off of this site.
I have tried manually carrying out the HardSPL using both the Prophet Tools GUI and the command line batch file HardSPL however after the procedure finishes my IPL and SPL do not read differently as all posts indicate (i.e. they do not read 2.G4.4PDA) ... instead they remain as 2.10.0001.
I have seen the phone go to the tri-colour bootloader screen and even the progress bar go up correctly however when it reboots it says 2.10.0001. I'm assuming that I cannot go ahead and flash with a ROM (such as the Shadow TE one until the SPL reads 2.G4.4PDA).
Can anyone offere me some help with getting to this?
Many thanks.
Nick (a very much noob!)
Click to expand...
Click to collapse
I would recommend you use something like: http://forum.xda-developers.com/showthread.php?t=353547 It makes it a one stop upgrade... That uses "JumpSPL" rather than HardSPL which is the short term option.
Thanks for the help I tried the alternative lazy tool and it worked (http://forum.xda-developers.com/showpost.php?p=2141436&postcount=188) now my Orange SPV M600 has the Shadow Touch edition rom on it with the shadow cube addon, so far works a treat.
I would still be interested to know why the SPL version number did not change using the prophet tools or HardSPL on its own.
Anyway many thanks again.
Nick
nisgar2k said:
Thanks for the help I tried the alternative lazy tool and it worked (http://forum.xda-developers.com/showpost.php?p=2141436&postcount=188) now my Orange SPV M600 has the Shadow Touch edition rom on it with the shadow cube addon, so far works a treat.
I would still be interested to know why the SPL version number did not change using the prophet tools or HardSPL on its own.
Anyway many thanks again.
Nick
Click to expand...
Click to collapse
What is your devices IPL?
It may be because Soft/Jump SPL was not executed properly prior to HardSPL (this is automated through the HardSPL tools and Prophet Tools).
HardSpl Problem
l3v5y said:
What is your devices IPL?
It may be because Soft/Jump SPL was not executed properly prior to HardSPL (this is automated through the HardSPL tools and Prophet Tools).
Click to expand...
Click to collapse
i ran upgrade_hardspl_g4 on my prophet, my spl is 2.15 still... what should i do l3v5y? tried flashing it 5 times still no luck. Please help, having a hard time upgrading roms...
ipl: 2.20
spl: 2.15
im currently downloading prophet tools 2.8. i currently flashed my 818 with PV_temp rom. i'll try to install the prophet tools and hardspl my phone with it.. hope it works...will update in a few after the installation is done... downloading so slow... =(
*-----------------------------*
i did it!! thanks!!!
I made it, use SoftSPL.
07/08/2009: I don't have Elfin anymore, so please DO NOT PM me asking how to CID unlock/USPL related questions. if you have any difficulty, post in this thread and wait for your fellow members to reply. thank you!
ELF IPL 1.17.0002 & USPL 1.17.0000This is a newer version of USPL for Elf (based on SPL 1.17.0000) for CID unlocking on similar lines of pof's Elf_USPL based on Elf SPL 1.11.0000.
Credits:
1. pof: for the 1st Elf USPL 1.11.0000.
2. ayyu3m: first person to test new USPL 1.17.0000 for me coz i dont have an Elf.
Note:
1. Should be used only on Elf with IPL 1.1X.XXX2. Some Elf owners have been using USPL 1.11.0000 with IPL 2.2X.XXX2 already without any problem. If that is the case, this USPL should work for those IPLs as well, but i can not guarantee.
2. Keep a shipped ROM for your phone in case of emergency.
3. If you are already using patched SPL 1.11.0000, then you can just run the romupdateutility.exe inside RUU folder to flash this SPL.
4. As it is based upon Elf_USPL, 'rapi' should be enabled before using it.
5. Check post 2 for USPL 1.19.0000, post 3 for USPL 2.26.0000 and post 4 for USPL 2.28.0000.
Don't hold me responsible if something goes wrong
Elf USPL 1.19.0000 by kokotas
ELF IPL 1.19.0002 & USPL 1.19.0000Another new USPL 1.19.0000 based on Elf original SPL 1.19.0000 has been patched by kokotas for CID unlocking. The nbh file of this USPL ready to be flashed can be downloaded here.
The procedure of flashing it is similar to previous USPLs and the instructions in post 1 apply to this USPL as well.
ELF & ELFIN IPL 2.26.0002 & USPL 2.26.0000
ALWAYS HAVE AN ORIGINAL STOCK ROM AS A BACKUP IF IT DOES NOT EXIST YOU ARE ONLY INCREASING THE RISK OF GETTING INTO MORE TROUBLE
Instructions for ELF.
EDIT 30/07/08: As confirmed by eshield (http://forum.xda-developers.com/showpost.php?p=2465989&postcount=96), Elf owners can directly upgrade the IPL/USPL.
EDIT 06/09/08: Directly upgrading IPL/USPL in one go may or may not work for all of Elf owners (if the Elf is pre-release or old one). If your phone (Elf only) is stuck at Smart mobility screen with IPL 2.26, SPL 2.26, try downgrading the IPL to 1.19 or 1.17.
For users that already have IPL 2.2X series
First make sure your device is application Unlocked. By installing EnableRapi.Cab & Cert_SPC.Cab on your device, then reboot the phone.
Take out MicroSD card from Slot.
Connect Device through Active Sync.
Run the elf-uspl.exe from the Extracted Download (ELF_USPL_2.26.0000.zip)
Watch Screen and Press Enter When Asked.
Screen should Jump to White on Phone and on PC Flashing Loading Bar will Show.
Stuck in Black Ducky Loading Screen?, check Active Sync Connection or Do a hard reset on Phone first. But be sure to do the last Actual Flashing in White Screen. Sometimes this needs a few tries to go through white screen.
Done.
For users that have IPL 1.1X series
Steps below are all recommended to remove Micro SD card.
First Make sure you allready have a Patched Pre 2.26 SPL (ELF_USPL_1.17.0000.zip)
You can install this Patched Wit the Same Instructions as above for the 2.26 SPL.
Then When you have a Patched 1.1X SPL install the 2.26 IPL (ELF_IPL_2.26.0000.zip)
After you have rebooted you can confirm your SPL & IPL versions by pressing Reset Button With Stylus and Pressing and Holding the Camera Button to get into TriColour Bootloader.
Reset Phone Back into the OS And follow instrcutions above for Flashing Patched 2.26 SPL.
At this point you do not to install CertSPC.cab & EnableRapi.Cab
Done
Unless you are familiar with these processes do not try them, and wait for more confirms.
Flashing is done at own Risk and might Void your Warantee.
Note:
You can also update the IPL&USPL to 2.26 together in one go if you are already using the USPL 1.17.0000 or USPL 1.19.0000. This has been tested by ChiemY(http://forum.xda-developers.com/showpost.php?p=2454555&postcount=44). So,if you are willing to upgrade together, download the ELF_IPL-USPL_2.26.0000.zip file and run the romupdateutility.exe.
ELF & ELFIN IPL 2.27.0002 & USPL 2.28.0000 V2Guys/gals, the USPL 2.28.0000 based on original SPL 2.28.0000 is ready for both Elf and Elfin
It wouldn't have been possible without the help of cmonex.
Credits:
1. cmonex : For helping me to solve problem of phone stuck in bootloader with original SPL 2.28 and checking the other patches.
2. pof : For the CID unlocking patch etc.
3. marchese : For the IPL 2.27.0002.
Procedure: the procedure remains the same as the prvious versions.
EDIT 30/07/08: As confirmed by eshield (http://forum.xda-developers.com/showpost.php?p=2465989&postcount=96), Elf owners can directly upgrade the IPL/USPL.
EDIT 06/09/08: Directly upgrading IPL/USPL in one go may or may not work for all of Elf owners (if the Elf is pre-release or old one). If your phone (Elf only) is stuck at Smart mobility screen with IPL 2.27, SPL 2.28, try downgrading the IPL to 1.19 or 1.17.
Those who want to upgrade to IPL 2.27.0002 and USPL 2.28.0000 together in one go, can download IPL_2.27_USPL_2.28.zip, the ready to flash RUU_Signed.nbh file.
EDIT 28/10/2008:
New released USPL28_V2 which has an extra feature (apart from the normal CID unlocking features etc) that you can flash ROM of any size now even below 50 MB using RUU. Yes, this USPL V2 removes the restriction of 50 MB size of ROM for normal RUU and that means the OS.NB doesn't need to be hexed if it is below 50 MB and one doesn't need to flash using SD card in order to gain the extra space.
BIG thanks to cmonex for enabling this feature. Enjoy!
Donate to cmonex
Ipl 3.07.0002 & Uspl 3.07.0000
IPL 3.07, 3.10 & USPL 3.07, 3.10This is the latest version of the IPL/USPL based on the original WM 6.1 WWE ROM 3.07.720.03. This USPL will:
1. CID unlock the device for flashing any ROM
2. Remove the restriction on minimum size (previous limit was 50 MB) of the ROM.
PS: the procedure to flash the USPL is same as before. If you are already using some USPL (USPL 1.17, 2.26, 2.28 etc), then you just have to flash the new NBH with RUU. Enjoy !
EDIT (17-11-08): New IPL 3.10.0002 and USPL 3.10.0000 attached
Ipl & uspl 3.14
IPL & USPL 3.14Here is newest IPL and USPL 3.14 . thanks to GPRS for sharing the original source of this IPL and SPL. The features and procedure to flash this USPL are same to that of previous USPLs. I've tested it on my Elfin and it works well
Enjoy
07/08/2009: I don't have Elfin anymore, so please DO NOT PM me asking how to CID unlock/USPL related questions. if you have any difficulty, post in this thread and wait for your fellow members to reply. thank you!
Dump the SPL from Elf(in)
Those who are interested in dumping their SPL from the phone, please follow the steps below:
1. Download the attached archive (thanks to kokotas).
2. Unzip it somewhere (preferably to the root of a drive).
3. Connect your phone to PC with USB cable.
4. Make sure that ActiveSync is working.
5. Run the DSPL.bat file and follow on-screen instructions.
After the SPL dump is finished, you will get a new file named SPL.nbx in the unzipped folder. But this will be a 512 KB dump file and CAN NOT be flashed to Elf/Elfin as such. Therefore, if someone wants to make a working SPL of the dump, please PM me the link of the dumped SPL.nbx file and i'll make a flashable SPL of the same.
EDIT: there is an easier method posted by dsixda to dump the SPL in this thread, i recommend to use that instead of this one.
http://forum.xda-developers.com/showthread.php?t=406721
Unlocks the CID (country ID) so that you can flash any Elf ROM to your phone.
Instead of flashing the USPL you can also run the temporary USPL (white screen method), but if you flash a bad ROM (bricks your phone) then you are in trouble, as the temporary USPL makes your phone back to CID locked afterwards.
The temporary USPL method also is annoying because it requires you to remove your sim/memory cards and may take several attempts to get it finally working... The flashed USPL, on the other hand, will let you run just the Update Utility and nothing extra... plus it works the first time always.
Dumping your IPL
1.Download the attached archive & extract on Desktop.
2.Go inside the folder DumpIPL & run the DIPL.bat
3.If everything went ok, you'll find your dumped IPL.nb in that folder soon
4.Do not use the generated file for flashing untill you post it in this thread & someone check that it's a "good" IPL!
Noonski said:
For the guy allready running SPL 2.26 on ELF can he check if Changing Pagepool size also works using ELF method on NBH file?
C now that this is the ELFIN SPL 2.26 your referring to.
I need to know this guy is absolutly sure it was an ELF
Click to expand...
Click to collapse
Hi
I am very sure mine one is an ELF (64/128) and confirm that changing pagepool size also works using ELF method on NBH file. My ELF is set at 6MB PP.
Moreover, changing the pagepool size with the attached pagepool changer for ELF is not a problem at all. Thanks to the creator for the pagepool changer.
*edit
Not only the boot time is reduced, the ELF now runs faster and the memory management is amazing, mine is set at 6MB PP, always show 25-26MB free memory
at most of the time after closing all application except background processes. I can say the memory leak is almost zero.
And the best of all, to flash a ROM, I do not need to take out the SIM card and Memory card.
Rgds
BTW, one thing I noted with 2.26 patched is that when I try to flash a ROM it will complain about Error 328 (I think), saying that the Update Utility is not compatible. This happens whenever the ROM says it has a version of 1.000.00.0 in the Utility. So if I change it to something like 3.000.00.0 in HTC Tools then it flashes fine
dsixda said:
BTW, one thing I noted with 2.26 patched is that when I try to flash a ROM it will complain about Error 328 (I think), saying that the Update Utility is not compatible. This happens whenever the ROM says it has a version of 1.000.00.0 in the Utility. So if I change it to something like 3.000.00.0 in HTC Tools then it flashes fine
Click to expand...
Click to collapse
Doesn't happen with me on my ELF and out of laziness i have version 1.000.00.0 set.
(or it might be because of my flashing frenzy)
I can Up my Update utility Next thing morrow.
htctouchp said:
yes, i also get these erros if my ROM version is like that. it happened to me even when i used USPL 2.20. so as a precaution, i've permamnently set my htcrt to ROM version of the base ROM 2.26
Click to expand...
Click to collapse
Okay so it might be a little ELFIN sickness then
It Propably won't make a difference but here's My Ruu anyway
upgrade from 1.19 to 2.26 ?
For the upgrade to 2.26, the procedure say to use elf-uspl.exe to upgrade the
SPL 2.26. If we have the IPL on 2.26 and the USPL 1.17 (or 1.19) why we cant
just update directly from the bootloader ?
And about the upgrade from IPL/SPL 1.19 to IPL/SPL 2.26 directly
in one file from bootloader ?
guys/gals...new USPL 2.28.0000 is ready and available for download in post 4 on first page .
ChiemY said:
For the upgrade to 2.26, the procedure say to use elf-uspl.exe to upgrade the
SPL 2.26. If we have the IPL on 2.26 and the USPL 1.17 (or 1.19) why we cant
just update directly from the bootloader ?
And about the upgrade from IPL/SPL 1.19 to IPL/SPL 2.26 directly
in one file from bootloader ?
Click to expand...
Click to collapse
yes, u should be able to do that directly. those instructions have been posted by Noonski as he was the one to test that on Elf (remember, i don't have Elf to test). but u can try ur method. if it works well, i'll modify the post
Well it was only after ckpv5 confirmed it.
Yes Merged Posts.
The reason why i did not Flash both SPL and IPL at the same time is because i like safety.
So is the version number of ROM flashin related to ELFIN's only?
(You know where you need to put 2.x into HTCRT)
As you can see below.... Why.... Some might do some different Flashing methods and as more Confirms come in this might change the method.
If there's anything none of us want to happen is someone to Brick their phone.
Boot Time vs Patched SPL's
Note: Time measured from the time 'Smart Mobility' appears on the screen. Soft Reset repeated 2-3 times on each USPL
1) USPL 1.11 (IPL 1.11) : ~50 secs
2) USPL 1.17 (IPL 1.11) : ~55 secs *
3) USPL 1.17 (IPL 1.17) : ~55 secs *
4) USPL 1.17 (IPL 2.26) : ~59 secs **
5) USPL 2.26 (IPL 2.26) : ~48 secs ***
6) USPL 2.28 (IPL 2.26) : ~48 secs
Conclusions:
* USPL 1.17 takes ~5 secs longer than USPL 1.11 (bit suprising)
** USPL 1.17 with IPL 2.26 takes distinctively ~60 secs from all the other combinations. Indeed a non-bootable combination.
*** USPL 2.26 and USPL 2.28 takes lesser time to boot conclusively
NOTE: This evaluation alone DOES NOT conclude you must use the latest SPL and IPL. But it gives you a CHOICE, to choose from different IPL and USPL, you can use to customize your device. Pagepool was not taken as a factor, and conducting Boot Time on a pagepooled ROM may also vary the results comparatively.
AND: i did this evaluation to show respect and appreciation on behalf of all others, to those members who give their precious time to this forum and bring out these patches, so that it may and does, help improve the way we can speed up and customize our elf and elfin.
And yeah, I got BSoD for the first time, when i flashed IPL 2.26 and USPL 1.17 and tried to interrupt a soft reset. This concludes what kokotas has said abt non-bootable combinations, like IPL 1.XX with SPL 2.XX or vice versa
USPL 2.28
htctouchp said:
This USPL should also work on Elf, but as i don't have an Elf, therefore it would be great if some Elf owner takes up the responsibility to test it.
Click to expand...
Click to collapse
Tested on my ELF, it works nicely. My SPL now 2.28.0000.
Will test further once AB release a new UCE ROM whether can flash without taking out the SIM card and memory card
Any chance to have IPL 2.28 too ?
Rgds
ckpv5 said:
Tested on my ELF, it works nicely. My SPL now 2.28.0000.
Will test further once AB release a new UCE ROM whether can flash without taking out the SIM card and memory card
Any chance to have IPL 2.28 too ?
Click to expand...
Click to collapse
i'm glad it works for u. i have not found IPL 2.28 as yet. however there is IPL 2.27 dumped by someone today and yet to be tested.
ayyu3m said:
Flashed a test rom with simcard and 2GB memory card inside.
hope you are very happy Aman. Good Job once again
Click to expand...
Click to collapse
yup, i'm happy if everybody else is
although i owe it greatly to cmonex who helped me to get over the problem with the original spl 2.28.
ayyu3m said:
As kokotas has stated:
IPL:2.2X.0002
SPL:1.1X.0000
NOT Bootable combination
This is the reason why i got the BsOD error as i have stated in post #26
haha! this shud make cmonex happy too. its like chain reaction. btw...see the above post as kokotas has stated, its true
Click to expand...
Click to collapse
yes, and thats probably the reason why there have been so many bricks in the past.
hi,
I have just use the great work from jockyw2001 on the USPL 1.16 to make:
USPL 1.34 from RUU_Vox_HTC_FRA_1.34.406.1_4.1.13.54_03.10.90_Ship
USPL 1.35 from RUU_Vox_ORANGE_UK_1.35.61.1_4.1.13.60_03.18.90_Ship
Currently i use the RUU_Vox_HTC_WWE_1.34.405.1 and i have follow this thread
to upgrade from SPV650
use CID-Bypass 1.34 and RUU 1.34 to USPL 1.34
upgrade RUU IPL/USPL 1.35 with Vox-IPL-USPL-1.35.patched
All files have work for me, i hope this work for you to
Credits: pof and jockyw2001
This is still a soft SPL? What benefits does this serve over the previous uSPL by jocky?
lol~~~~
tested, both of USPL and hardSPL worked fine.
The hardSPL version is 1.35.0000Cy
Thank you for your great job.
h4waii said:
This is still a soft SPL? What benefits does this serve over the previous uSPL by jocky?
Click to expand...
Click to collapse
I dont know the change between the SPL 1.16 and 1.34/1.35. The patch
method was strictly the same. This is just for people like me who want
everytime the last release
I see.
Well thanks for your work in patching the new SPL. Hopefully somebody can merge or sticky this thread.
which file should i use for hard SPL? will it work forever means i can update any VOX unofficial ROM without running any SPL later?
It works as long as you don't flash an official ROM. It doesn't really matter which one you use. 1.16 is working perfect on my device, so should these!
frauhottelmann said:
It works as long as you don't flash an official ROM. It doesn't really matter which one you use. 1.16 is working perfect on my device, so should these!
Click to expand...
Click to collapse
1.16 is USPL means software SPL, i also use that to bypass CID and it needs to run everytime whenever you are flashing any ROM.
But my concern is if there is some Hard SPL and i run it on my VOX once, would i need to run USPL/HSPL again whenever i need to flash any ROM or will it work forever so that i can simply flash any ROM without using any SPL further.
If you FLASH uSPL instead of simply patching it through RAM, you will have an SPL that acts HARD until you flash an official ROM as it will overwrite the SPL since it is not a true HardSPL.
Take the same steps to patch uSPL and then instead of flashing your ROM, run FLASH.exe from within the uSPL directory, flash USPL and then flash your unofficial ROM. Patched uSPL will remain on the device and thus it will act as a HardSPL to any unofficial ROM and you will not need to patch SPL every time you flash an unofficial ROM.
Will this USPL allow me to flash an unofficial ROM on my Vox that has got the latest WM6.0 Orange UK ROM on?
Roland
Please help..
Hello, i have an Orange France SPV e650, every time i run sda application unlock thing it says "phone not unlockable" then it says succesfully unlocke, now it wasnt succesfully unlocked cos the flash does not work, stops at 3 percent.... Please help me I really look forward to ROM upgrade.
Thank you,
Sammy
BIG THANKS TO ChiemY
I can't believe how long it took me to solve this riddle lol. Was trying use Vox USPL- CID BYPASS for 1.16 and just took a lucky guess at using the number that seemed to be shown on the bootloader so often being 1.34 . It's my first time playing with WM HTC devices and it seems it will be smooth sailing from now on .
I flash HTC P3400 with Vox USPL and when phone restart that goes in blank screen, now it does not flsh anything, please help
I flash HTC P3400 with Vox USPL
I flash HTC P3400 with Vox USPL and when phone restart that goes in blank screen, now it does not flsh anything, please help
You have successfully bricked your device - may it rest in peace. The SPL is the part of SW that opens the door to other SW loading. If that does no more work you are lost.