Related
What do I use to remove the scratch? thx.
slikr said:
What do I use to remove the scratch? thx.
Click to expand...
Click to collapse
I see a kit for ipod for that exact thing a few years ago - maybe its worth asking.
i dropped my diamond and the screen has a very nasty looking scratch along the botto of the screen.
please advise what i can do to fix or do i have to replace it for a new touch screen.
if i need a new screen where in th uk is the best place to have it re fitted
thanks
I think it's called Displex scratch remover or similar - try it out it will fill the hairline scratch and make it invisible.
salada2k said:
I think it's called Displex scratch remover or similar - try it out it will fill the hairline scratch and make it invisible.
Click to expand...
Click to collapse
Are you sure this will work? Displex melts a bit of the acrylic plastic on most screens so that it fills up the scratches. Last I heard, the Diamond's screen is glass.
OnePointOh said:
Are you sure this will work? Displex melts a bit of the acrylic plastic on most screens so that it fills up the scratches. Last I heard, the Diamond's screen is glass.
Click to expand...
Click to collapse
If its the screen I'd be carefull applying anything as you risk the display becomes blurred (same reasons thet don't remove scratches on glasses). If it's made of glass maybe consult a car repair shop reparing wind screens. Let's hear what you find out.
OnePointOh said:
Are you sure this will work? Displex melts a bit of the acrylic plastic on most screens so that it fills up the scratches. Last I heard, the Diamond's screen is glass.
Click to expand...
Click to collapse
The outer layer is not glass. It's the layer underneath the digitizer that is glass. Have you noticed that you can indent the screen when you touch it, say, with the stylus? That should prove it for you.
As far as the displex goes I personally haven't tried it as I use a screen protector (which on a side note I have ruined today as my stylus has developed a sharpness that has scratched the crap out of it). So the idea is to replace it when it's gone bad with a new one. If you've scratched the actual outer surface then you could look at replacing it (I'm not sure how you'll go about doing that) or you could try the displex.
Attention: use only on non-coated surfaces and plastics; when used on mobile phones, treat only the transparent portions of the display lens. Not for use with touch screen displays.
JayZee2 said:
Attention: use only on non-coated surfaces and plastics; when used on mobile phones, treat only the transparent portions of the display lens. Not for use with touch screen displays.
Click to expand...
Click to collapse
Uh-oh... Haha I think I recommended Displex to someone before... I've seen people use it on GPS displays and it worked fine, even with touch screen... But if they say no, don't risk it.
looks like it will have to be a new screen,
is the outher screen a seprrate part to the glass section of the screen ??
does anyone know where i can have it replaced in the uk?
If your going to replace it then I'd have a go at polishing it first and see what happens. What you got to loose.
I once used a bit of Brasso on the screen of my car headunit, got the scratches out a treat.
silkw0rm said:
looks like it will have to be a new screen,
is the outher screen a seprrate part to the glass section of the screen ??
does anyone know where i can have it replaced in the uk?
Click to expand...
Click to collapse
If you're going to have a new screen anyway I'd first experiment with some of the various proucts discussed. If it works you save the repair, if not then no harm done as you'l get a new dispaly (at the cost of a new TD likely).
update
managed to get hold of a new screen for a reasonable price too
link
http://www.mobilefun.co.uk/product/17042.htm?referer=FR_PROD-PR-P-17042
now can someone please direct me to where i can have this fitted,
or better still if you know how to change the screen can you please show me instructions of this and tools required.
regards
silkw0rm said:
update
managed to get hold of a new screen for a reasonable price too
link
http://www.mobilefun.co.uk/product/17042.htm?referer=FR_PROD-PR-P-17042
now can someone please direct me to where i can have this fitted,
or better still if you know how to change the screen can you please show me instructions of this and tools required.
regards
Click to expand...
Click to collapse
Search for the tech. manual on the net. It explains step by step how to do it. Good luck with it. I cannot recall where I found it, but even somewhere in xda is a link I think.
http://www.pdacenter.ru/razborka/raz...touch-diamond/
it was in my housing replacement thread before...
very difficult job from what i can tell for replacement
almost as annoying as iphone DIY since it has the most annoying housing ever
this may sound stupid but it is stuff that works
take a piece of microfiber cloth
a banana
toothpaste
and any glass cleaner
1st take a small piece of banana and rub it on the screen for about 3 minutes and take your microfiber cloth and whipe it off... (do not use water) and do not use paper towel or toilet paper!!!!(it will ruin the screen
now flip your microfiber to the clean side and set it down...
take your tooth paste (white colgate is the best) and rub it over the screen for 5 minutes again take the clean side of microfiber and rub off the toothpaste... it will smell minty for a couple of days but eventully it will go away!!!
please try this it works take the time it will work and again do not use any water!!! that means dont put water on cloth and wipe off
hope it helps
htcfanboi said:
this may sound stupid but it is stuff that works
take a piece of microfiber cloth
a banana
toothpaste
[..]
hope it helps
Click to expand...
Click to collapse
Right... I can understand using tooth paste, but a fricking bannana? How funny is that? I honestly would like to see a guy polishing his £350 phone with that.
You've made my day
Ps. I'd suggest using a carrot and then a potato afterwards
COuld be the small amount of acids in it.
A lemon may be too strong. Banana has a fine 'polishing' structure too.
it works man.... banana is my friend......
delicious too
htcfanboi said:
it works man.... banana is my friend......
delicious too
Click to expand...
Click to collapse
Hehe, My apologies then, I'm gonna give it a go as soon as I spot the first scratch
im trying to crack the transformer open and do u think the back is glued on or is it screwed on? im thinking theres probrably some screws behind the lable but cant seams to find anything here that wont scratch it to remove it. hit me up with ideas and hopfully I can post some kind of video on how to dissacemble the transformer.
It will most likely be fastened with screws. I think if it had been glue peoples cases wouldnt be 'creaky'. There were some pics on a Chinese site showing it open. I saved them to my pc, If I find them I'll upload.
Edit: Well I found them but they're not really showing the case. I'll attach them anyways and you can see if they help or not. It looks like once you get the bezel off the back just slides clean off.
Ok well scratch screws under the asus logo, thanks very much for those pics. I already have the screws out from the bottom. I'm guessing the back seals with some type of clips
Looking at there tools in second picture seams they used a guitar pic to losses it from its edges
cowballz69 said:
Looking at there tools in second picture seams they used a guitar pic to losses it from its edges
Click to expand...
Click to collapse
Maybe try a credit card?
Ha tore up my room looking for my guitar pic lol. Ill try my credit card
When in doubt use a hammer.
stuntdouble said:
When in doubt use a hammer.
Click to expand...
Click to collapse
Lol, tryed to use a credit card but its to thick, going to stop at the store tomorrow and pick one up
cowballz69, pm sent
If you have one, your best bet is a Stanley knife (boxcutter, I think you call them). Should be thin enough, you'll just have to be careful not to nick any internal crap.
If it were me, I'd use a scalpel, but I know most people don't have one handy.
ok well heres my mini review untill i get a guitar pick, i got the bottom half to crack open with a credit card(to thick but i did it), i was then able to slide the card from one end to the other. The plastic clips holding the metal are very very crappy. the metal was extreemly easy to bend and by just putting the card threw the bottom was enough to bend it. i was however; able to put it back together with out making it look as if i opened it, but u would need a ULTRA Thin piece of plastic to complete the mission(DO NOT USE ANYTHING ELSE BUT PLASTIC,,THE METAL AROUND THE EDGE IS SUPER FRAGLE). seams all ASUS does is pop the plastic backing in and screw the bottom and its off to who every buys it.
(Losining the bottom screws lowerd the light bleed that was there by 30% ( i was a full brightness and back screen and loosining the screwes made a big impact so the issue with the light bleed is to much pressure on those areas)
seams this is easy enough just need the right tools.
cowballz69 said:
(Losining the bottom screws lowerd the light bleed that was there by 30% ( i was a full brightness and back screen and loosining the screwes made a big impact so the issue with the light bleed is to much pressure on those areas)
seams this is easy enough just need the right tools.
Click to expand...
Click to collapse
Interesting. That seems to be the very spot where my screen has a little backlight bleeding. I'll try it out in a few minutes.
Youtube it
If this is the fix. A youtube vid would be awesome. Ready set go
paleridr said:
If this is the fix. A youtube vid would be awesome. Ready set go
Click to expand...
Click to collapse
thats not the only spot i have light bleed, i also have bleeding on the top portion and theres no screw to losen so must be on to tight from the inside. however this does prove that the bleeding is from pressure not the screen itself
You need these spudgers,
http://www.dealextreme.com/p/professional-premium-precision-phone-disassembly-tool-7-piece-set-23050
Get a few sets (if you're planning on opening up electronics on a regular basis). These are soft plastic, and will wear out after a few uses. You don't want to use anything harder like a knife, as then you will mar the 'lips' on the device shells. Aesthetics aside, that will show up as evidence of tampering, meaning goodbye warranty.
Most electronics use plastic snap-in clips to hold the shells, along with screws and possibly soft glue. Going slow will prevent the clips from snapping off, but not always.
You can find these same tools on Amazon and eBay. Just search on 'spudger', which is their name.
Use the guitar pick to get the initial crease, push one of the thicker wedges into the crease, and slide it along the seam. This assumes you've gotten all of the (hidden) screws.
e.mote said:
You need these spudgers,
http://www.dealextreme.com/p/professional-premium-precision-phone-disassembly-tool-7-piece-set-23050
Get a few sets (if you're planning on opening up electronics on a regular basis). These are soft plastic, and will wear out after a few uses. You don't want to use anything harder like a knife, as then you will mar the 'lips' on the device shells. Aesthetics aside, that will show up as evidence of tampering, meaning goodbye warranty.
Most electronics use plastic snap-in clips to hold the shells, along with screws and possibly soft glue. Going slow will prevent the clips from snapping off, but not always.
You can find these same tools on Amazon and eBay. Just search on 'spudger', which is their name.
Use the guitar pick to get the initial crease, push one of the thicker wedges into the crease, and slide it along the seam. This assumes you've gotten all of the (hidden) screws.
Click to expand...
Click to collapse
breaking a clip is def possible in this case
How did you get the screws on the bottom off? Do you have the right screw driver (any ideas where I can get one)?
jrac86 said:
How did you get the screws on the bottom off? Do you have the right screw driver (any ideas where I can get one)?
Click to expand...
Click to collapse
it's a torx.
jrac86 said:
How did you get the screws on the bottom off? Do you have the right screw driver (any ideas where I can get one)?
Click to expand...
Click to collapse
Use a Torx T6 bit.
When you opened it up, was there anything to suggest there was any way Asus would know you had opened it up please (if you hadnt bent the bezel ofc) if you needed to send it back under warranty for some reason?
opening is not recomended threw my experiance * I used the thinnest guitar pic today*,and the metal around the edge;any slight flex and it ends up staying that way and wont go back on straight no matter how carefull u are, also the clips that hold the plastic back to the bezil is ULTRA CRAPPY to a point u have a 50 50 chance of it not holding the plastic cover anymore. ON the plus side; if u loosen the bolts in the bottom, u can relieve the light bleed there. so reguarding the light bleed its best to just send it back to ASUS to get it fixed.
MY Next step is having ASUS fix my light bleed on my own tablet and not have them give me a replacement.
I will be posting a before picture of the light bleed when i send it out , and a After picture on when i recieve it back from them. good idea??
Any info or links would be great
Got the phone off ebay and looked like it had been kicked about.
I plan to replace the touchscreen , lets hope iam not out of my depth ^_^
cheers
hep
Just go to a Samsung Service Center and get it replaced.
It's the best option.
I have seen other Android Phones which had their screens replace the unofficial way and a partial part of their screen was no longer functional....
as a comparison, you can check it out at http://www.globaldirectparts.com/Samsung-Galaxy-Fit-S5670-Digitizer-Touch-Screen-p/smsng6102880.htm
ok so i done it worked ok
would not recomend this for anyone and if you do its your fault
tools i used few screwdrivers tweezers scalpel cleaning cloth screen cleaner
small tray to work on , lil bag for screws
1. switched off phone , removed back cover , memory card , sim and battery
2. carefully removed the 6 screws and put in bag, the removed the backplate was a pain but managed without breaking it.
3 next there was a connection at top and on left hand side to disconnect , all so the headphone connector comes off , then you can take the motherboard off.
4. now it got tricky !very small part with a 9 on it pull the black tab up and leave it lose . i heated the front up a bit for next bit then gently got the digitizer lose it has some clips at bottum so start at the top .
5. cleaned a finger print off the lcd and replaced with new one , rebuild and was surprize it worked tbh
enjoy the pictures
hep
ohhh did u replace the screen by yourself!!!
yes was a pain
but good for you that it worked...
You've got the balls man..
hep2o said:
yes was a pain
Click to expand...
Click to collapse
WOW u have the skillz man
Hi xda, so I got tired of having dust under my screen and decided to try to fix this myself, I used many disassembly videos and this http://forum.xda-developers.com/showthread.php?t=1479734&highlight=dust as guides, initially I didnt open my phone completely, and used a hair dryer to heat and loose the glue, I guess that wasnt enough, then I finally separated the glass from the screen and procedeed the cleaning, everything good.
Then when I pushed the glass and realized there was a little space between the glass/lcd and the plastic frame (look at pic), tried to put the back cover in again and noticed the right side of the phone, the plastic one was kinda lifted and barely fitted my back cover again, reopened and realized this (look at pic) it seems that the main frame and plastic frame (pic again) got a bit separated, when I was trying to lift the glass i heard some cracks there, I tried pushing it gently but I dont want to damage the lcd, next thing im gonna do is disassemble it completely and hit gently the lifted side of the frame with a hammer so it fits flush again, before doing this, Do you have any sugestion or advice? Has this happened to you?
Also since I dont have a proper heat gun and I'll be using a hair dryer I would thank you if you know and can tell me what areas of the lcd are glued to the main frame, pic attached, if you know you could use paint to point them.
Im a bit worried about the tension the phone is getting with the cover on, I hope only the main frame is getting it... as the phone is pushed to its side (0.5-1mm maybe) I cant plug my headphones and i get slightly worse overall signal. Thank you in advance for any help.
Dom42 said:
Hi xda, so I got tired of having dust under my screen and decided to try to fix this myself, I used many disassembly videos and this http://forum.xda-developers.com/showthread.php?t=1479734&highlight=dust as guides, initially I didnt open my phone completely, and used a hair dryer to heat and loose the glue, I guess that wasnt enough, then I finally separated the glass from the screen and procedeed the cleaning, everything good.
Then when I pushed the glass and realized there was a little space between the glass/lcd and the plastic frame (look at pic), tried to put the back cover in again and noticed the right side of the phone, the plastic one was kinda lifted and barely fitted my back cover again, reopened and realized this (look at pic) it seems that the main frame and plastic frame (pic again) got a bit separated, when I was trying to lift the glass i heard some cracks there, I tried pushing it gently but I dont want to damage the lcd, next thing im gonna do is disassemble it completely and hit gently the lifted side of the frame with a hammer so it fits flush again, before doing this, Do you have any sugestion or advice? Has this happened to you?
Also since I dont have a proper heat gun and I'll be using a hair dryer I would thank you if you know and can tell me what areas of the lcd are glued to the main frame, pic attached, if you know you could use paint to point them.
Im a bit worried about the tension the phone is getting with the cover on, I hope only the main frame is getting it... as the phone is pushed to its side (0.5-1mm maybe) I cant plug my headphones and i get slightly worse overall signal. Thank you in advance for any help.
Click to expand...
Click to collapse
I wanted to try it myself, but didn't have the guts. Sorry to hear your problem.
The guide said "5. Clean off all the crappy double sided tape from the factory."
It seems to me that you have put the same double tape. I suggest you remove the LCD again, clean the old tape and apply a new one.
Good Luck!
Edit: Does your touchscreen work well?
elvisypi said:
I wanted to try it myself, but didn't have the guts. Sorry to hear your problem.
The guide said "5. Clean off all the crappy double sided tape from the factory."
It seems to me that you have put the same double tape. I suggest you remove the LCD again, clean the old tape and apply a new one.
Good Luck!
Edit: Does your touchscreen work well?
Click to expand...
Click to collapse
Dont be afraid of trying, i was also scared at first but bah, 1. There's no official htc support in my country 2. I dont trust repair houses. 3 I wont wait 2-4 weeks for something relatively easy. So why dont try by yourself?
"Clean off all the crappy double sided tape from the factory" I dont have double sided tape at hand right now, getting it in 2 days, however thats not the problem, the glass sits flush and tight even with the old tape, the problem is that as i said my phone somehow got wider and the back cover is hard to put. Thanks, im gonna need good luck.
Oh and yes my touchscreen works perfectly.
Dom42 said:
Dont be afraid of trying, i was also scared at first but bah, 1. There's no official htc support in my country 2. I dont trust repair houses. 3 I wont wait 2-4 weeks for something relatively easy. So why dont try by yourself?
"Clean off all the crappy double sided tape from the factory" I dont have double sided tape at hand right now, getting it in 2 days, however thats not the problem, the glass sits flush and tight even with the old tape, the problem is that as i said my phone somehow got wider and the back cover is hard to put. Thanks, im gonna need good luck.
Oh and yes my touchscreen works perfectly.
Click to expand...
Click to collapse
There's no HTC support in my county either. Maybe it got wider because of the heat. Even though the glass sits tight I suggest you change the old tape, cause that's what let dust in the first place. The guide said also smth about silicon, did you apply it?
Was it difficult to remove the LCD with the hairdryer? I don't have a heatgun.
LOL, seems I'm the one doing the questions now.
elvisypi said:
There's no HTC support in my county either. Maybe it got wider because of the heat. Even though the glass sits tight I suggest you change the old tape, cause that's what let dust in the first place. The guide said also smth about silicon, did you apply it?
Was it difficult to remove the LCD with the hairdryer? I don't have a heatgun.
LOL, seems I'm the one doing the questions now.
Click to expand...
Click to collapse
No it didnt got wider because of the heat, when i was trying to open it i forced the bezel/metal main frame (4th pic) so it unclipped. Getting the double tape tomorrow. No way im gonna put silicon, ill put just 4 tiny squares of doublesided tape, i would rather clean it monthly than that, also i keep it always clean, it just had the dust before (second hand).
Yes, it was very difficult to remove the LCD, dont even try this without a heatgun, i was lucky to not mess something else duh i even crushed the LCD cable a bit, but it works normally. Only solution now is to get a new main frame.
Dom42 said:
No it didnt got wider because of the heat, when i was trying to open it i forced the bezel/metal main frame (4th pic) so it unclipped. Getting the double tape tomorrow. No way im gonna put silicon, ill put just 4 tiny squares of doublesided tape, i would rather clean it monthly than that, also i keep it always clean, it just had the dust before (second hand).
Yes, it was very difficult to remove the LCD, dont even try this without a heatgun, i was lucky to not mess something else duh i even crushed the LCD cable a bit, but it works normally. Only solution now is to get a new main frame.
Click to expand...
Click to collapse
Thanks for the advice. I hope you manage to fix your phone
Alright, I did send sms on my bicycle which resulted in I did drop the phone on the ground. Luckily I had ad NILLKIN glass screen protector, which did save most of the phone . I have ordered a new Nillkin screen protector from Aliexpress. And I hope to patch up this phone so it looks good again. How would you have done ?
As you can see at the bottom in the pictures there is physically damage, you can you see the screen bleeding thru also the huwawei logo is damaged.
My idea is UNDER the NEW Nillkin screen protector I will try to mask these "holes" so the screen is not beelding thru anymore. What material should I use to patch up these holes.. also.. how to repar the logo ? can I print it out on my computer printer ? it might look **** on paper but UNDER the glass protector it might look a lot better.
All creative ideas are appreciated, I have high hopes the phone will look good again..
And hopefully my phone will surrive until the M8 release.
Just to let you know desipite the glass look damaged like this the phone is still fully functional!!
ouch i can feel with you.
How about some black film, black paper or everything else that is black and thin
Yes some black material for sure.. Black film would be perfect in guess.. Just wonder where to get it also some black glue at the sides also..
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
alexre123 said:
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
Click to expand...
Click to collapse
Nice man might be a very good alternative! But how easy is it to change it really?
Do I need a heat gun for that?
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Or...if you have the courage go for it ) - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Joke man, don't do it yourself if you don't have experience
alexre123 said:
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Click to expand...
Click to collapse
I have done some smartphone repair myself, I changed the USB board on my old Galaxy Note 1.
I bought a smartphone repair kit with a few tools and very small screwdrivers. To change the glass is probably not much harder, but I need to know if I need a heat gun since I do not own any yet Hopefully it is not needed..but I would assume so...
I might also add the reason I bought a screen protector was that the original glass underneeth have a small crack too that goes accross the entire screen but it s quite invisible besides from certain angels.. so to change that screen to would actually be amazing..and it would make the secondary value when I sell this when M8 is released be a lot higher..
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
alexre123 said:
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
Click to expand...
Click to collapse
Yes the Nillkin glass did its job but I think I was unlucky, that the bottom of the phone got under my bicycle tire.. it felt like it...
I recommend Nillkin, IT has very good Oleophobic coating, which makes the whole device a lot more enjoyable to use, but be careful whren you put it on non 100% straight surfaces it will slip onto the floor.
Alright it is more or less decided I will buy a new front cover with glass, I will make sure to get original parts with gorilla glass. Since the ebay link you linked to are chipped from china I guess I can just order straight from alixpress instead...
I have heard singapore post have quite fast shipping compared to china post.
just one question is hard to see in the videos.. but do I really need to disassembly every component all the circuits boards just to change the front screen ? do I need to open the case at all when using the heat gun/hair dryer ?
If as in the every component and circuit board has to be disassembled it is over my competence probably... unless I am super careful..
Mutch better if you want to purchase an original front to replace it. Don,t know if you really need to take all the components of for replacing the front screen, but you can make some research on it or you can ask on other forums, maybe are others with more experience.
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
blackinfinity said:
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
Click to expand...
Click to collapse
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
ehhm... good luck OP
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
blackinfinity said:
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
Click to expand...
Click to collapse
Sorry but you are like 10 year old child..
So u wanna change your ''front Screen Outer Glass Lens'' ??? (that is damn long name for glass )
You have so much hopes ? OK .. go on .. I leave you to it ..
I wish you very best of luck ..
''''IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT''
DDDDDD this was so funny :laugh: :good:
Fingers :fingers-crossed:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
blackinfinity said:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
Click to expand...
Click to collapse
And I will give you one last advice ; that my detailed post above I explained you how difficult it is .. YOU want to change glass only ??
And what you think, you can just do it without stripping phone apart ?? Are you magician ? You would have to open phone anyway !
And replacing glass on your screen, do you have any idea how you gonna do it? Removing glass from LCD is x10 TIMES hard that my instructions above man !
So you basically adding even more, harder work to hard work ..!
Do you even have
1.LCD separator heat machine ??
2.Cutting line wire ??
3.Cleaning alcohol chemicals ??
4.Optical clear adhesive glue ??
5.Ultraviolet curing lamp ??
Come oon man ...
I told you I wish you very best of luck..
This guy want to do the exact same thing - https://www.youtube.com/watch?v=O8HNBtl9MwI
You have the all process here - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Take a look and decide if you want do it yourself and risk to mess things up or go with the phone and the replacing part to a service and let someone who did this before.