i have a jabra sp700 and the jack. i can connect just fine, however, if i want to play music, i have to go into bluetooth setting, uncheck headset and wireless speakers, hit done, then go back in and recheck headset and speakers.
is there a setting i can change to not have to do this?
Related
I am using I-tech clip radio it support A2DP, AVRC with buit in FM radio receiver and sound quality is great.
But i am facing a problem -
My Wizard detects it as 1.Wireless Stereo and 2.hands free
After paring it plays music and handle call very well
Once i switch off BT on phone then again switch on to reconnect it connects only Hands Free part not Wireless Stereo - so music doesn't come on Hands free
If i start A2DP from Battery Status it transfers music but very poor sound quality and AVRC function.
I even tried Widcomm BT Stack but no help.
So after every switch on/off of BT i have to delete and pair it again with my phone.
Please help
I have same problem
rom TNT 273
genius bt-03i
sometimes it hepls when I turn my headphones off and on again and at bluetooth devices I tap and hold stylus on my phones and click set as wireless stereo, sometimes I have to unpair and pair again...
Solved
If i follow these steps it works -
OFF
1. switch off BT on phone
2. Switch off Handsfree
ON
3. Switch on Handsfree
4. Switch on BT on Phone in Connectable mode
5. After few seconds in BT config panel select & hold on listed handsfree set as wireless stereo
This process works very well
in my BT panel "Set as wireless stereo" stays grey after this procedure :-(
running tnt series pro on a g3 and trying to connect Jabra BT-320s
I just got a Bluetooth headphone/headset (with mic) to use with my GT7+ (GT-P6210 wi-fi only) and my semi-smart phone. The headset (Motorola MOTOROKR S305) has three different pairing modes: music only, phone only, and both.
When I pair it with my little phone, it automatically pairs as both. It works fine as a phone headset (mic and earphones), and it works fine as a stereo headphone with the phone's music player.
When I pair it with my GT7+, it automatically pairs as music-only. There is no microphone function. With Bluetooth off, I can make calls using the GT7+ built-in mic and speaker and the GrooVe IP app. No problems. But with the Bluetooth headset paired, I just don't get the mic function. I can hear the phone audio in the earpieces, but the mic is dead.
Is there any workaround? Is there a way to get the GT7+ to identify itself as a phone-capable as well as music-capable device for the purpose of Bluetooth pairing? (That's what I think must be missing.)
TIA.
I can't speak for that particular headset but I successfully use a jabra (phone headset only) and GV with my tab plus. However, before I had a A100 tab and I had similar mic problems with the same jabra headset...so the whole compatibilty thing seems to be hit or miss.
I assume you checked settings to confirm there are no options to adjust mic? Also, you might see what happens if you pair and use GV right after boot.
jhorner said:
I can't speak for that particular headset but I successfully use a jabra (phone headset only) and GV with my tab plus. However, before I had a A100 tab and I had similar mic problems with the same jabra headset...so the whole compatibilty thing seems to be hit or miss.
I assume you checked settings to confirm there are no options to adjust mic? Also, you might see what happens if you pair and use GV right after boot.
Click to expand...
Click to collapse
I did check settings and I didn't find anything relevant. I also tried pairing while GrooVe IP was running and logged into GV. I'll try that again right after boot. Thanks.
Dear all,
I would like to use my headphones with a bluetooth microphone or headset. I like my earphones and don't want to go through the wireless A2DP BT to listen to music, but in the same time I would like to have the possibility of a hands-free solution. So my question, is it possible to have the sound output on the earphones and the sound input on the mic of a bluetooth headset (like a clip-on on which I don't connect my earphones)
Is there anybody that can fiddle with his device if he has the proper hardware?
Thanks
i think its not possible. if i connect my phone to car, audio-output is only available via bluetooth
splinter03 said:
i think its not possible. if i connect my phone to car, audio-output is only available via bluetooth
Click to expand...
Click to collapse
it allso screws up your audio quality
Ok, so on my other phones I could have my Bluetooth connected, be playing music through an auxiliary cable to my truck speakers, when I get a call, switch audio to my Bluetooth.
On my S5, it doesn't give me the option to switch, the audio just stays on the truck speakers.
Is there any way to change this to have it play music through speakers, but phone calls through Bluetooth?
I have the gear s3 connected to my oneplus 3t by BT only.
Whenever i go into my car (have a BT speaker), both watch and car speaker appear as connected.
However, "phone audio" is always picked by the watch and not by the car speaker.
The best way i found to switch BT audio back to the car is doing it manually from the BT menu which is not a realistic solution.
Is there anyway to "prioritize" BT phone audio in a way that when i get into my car the speaker will automatically be chosen?
It has been discussed before in this link https://forum.xda-developers.com/showthread.php?t=3650826