hi there
i am using imate jamin da problem with my cell is
i upgraded my rom to qtek 2.20000 it was working absolutely fine with 8 icons in my comm manager then i upgraded to RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-b1 and it has severely damaged my cell as my phone my phone hangs white booting it shows me the colour screen with
IPL 1.00 and SPL 2.20.0001
on the Screen
OS and GSM is not displayed
I tried rom update several times but its not working
i even tried to format my phone but it gives FAT16 format failed
I even tried to upgrade to jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 but still its not working and givng same problem
now i dont understand what to do
i just brought this phone from dubai last month its under warranty will imate people sort this problem ????
guys please give me Advice and solution for this IPL SPL Problem
Thanks in Advance
Hello, I feel sorry for your bricked Prophet but here some informations. First of all, there is no need to write in big red letters. This usually annoy people or make them feel offended. You are not more important than others - who have their own problems as well. Writing normally would usually give better chances for a reply.
Here some feedback for your problem :
a) As long as you can get back into the boot loader as long everything is recoverable (hold camera button and reset and keep the camera button pressed until you get into the boot loader with the different colors). As long as this is still there as long you can recover.
b) Get an official ROM from your service provider for your Prophet and flash it back.
c) Only problem you might have is the updated boot loader (2.20).
big red annoys me.
You did not try to flash your G3 phone with a G4 rom now did you? (or G4 with G3 rom..)
As Spatzm said: Try to get into bootloader. If that works try updating again with the official qtek 2.20 rom. (here). And READ that topic about how to install and get yourself the ROMUpdateUtility_NoID.exe from the ftp (see wiki).
Since you tried to update with the 2.20 rom (which is the base of Jesters rom) you cannot downgrade, that's why you need to use the 2.20 official qtek rom (which is suitable for both G3 and G4). You can only downgrade if you have a CID unlocked G3 (if you don't know if it's CID unlocked then it's not ) with a G4 device you cannot downgrade to put it down shortly.
Hi guys,
I've just implemented a Vox USPL which allows you to flash any Vox ROM updates, i.e. you can flash any *official* ROM even if your phone's model and vendor ID doesn't match. It's confirmed that you can also flash cooked ROMs
This SPL is based on original Vox 1.16 SPL but includes 3 patches:
1) g_cKeyCardSecurityLevel = 0 (set 32)
2) Does not check Model & Vendor ID
3) Does not check signature*
(*) code must be formally signed i.e. contain properly-formatted signatures on the right places, however no checking is performed against them.
This means you can flash ANY ROM to your Vox after running USPL on it, no need to pay for CID unlock anymore!
The USPL will *not* help you to SIM unlock your device. You still have to pay for that.
The USPL runs in RAM and is *not* flashed to your device, so there is no risk there. Once it runs you can run any official Vox ROM update utility.
The USPL does *not* permanently CID unlock your phone, like the CID unlocker from imei-check or so.
After you flashed a ROM your phone is again CID locked. Each time you wonna flash a ROM with a different model and/or vendor ID (different from your phone) or a cooked ROM, you must run the USPL again and then flash the ROM.
It's beta and untested and the risk is entirely yours !! Don't blame me if you brick your phone
EDIT:
You can now also flash the USPL allowing you to flash any unsigned (cooked ROM or ROM module, e.g. radio or OS) or signed ROM with any model/vendor ID. The USPL substitutes your SPL until you perform a full ROM update. Consider it as an extra insurance in case something goes wrong with flashing cooked ROMs or any other ROM update !
Instructions:
1. Run the USPL (Vox USPL- CID BYPASS.zip)
2. Run the ROMUpdateUtility.exe (Vox-USPL-RUU.zip)
Have fun,
JockyW
The attachments:
SDA_ApplicationUnlock.zip : application unlocker if u need it
mtty1.42.zip : terminal emulator (not neccessary if u only do ROM updates, but if you wonna play with the bootloader commands you need it)
Vox-USPL-RUU.zip: flash version of USPL (Note: you must first run USPL from "Vox USPL- CID BYPASS.zip" before you can flash it with ROMUpdateUtility.exe from Vox-USPL-RUU.zip !!!)
Vox USPL- CID BYPASS.zip : instructions included
Credits: in particular to pof. This USPL and also the one for Excalibur is based on his USPL for the Elf. See here
I think this is one of the most fantastic news of the century!!!
Finally some cooking can start on this little device.
Thanks again,
Ka.
noob question
what the difference between sim unlock and cid unlock?
This can be found in various threads around here, anyway.
SIM Lock - You can't use a SIM from a different provider than the one who sold you the phone.
CID-Lock - You can't flash your phone with a ROM which hasn't been cooked by your provider (or manufacturer for HTC unbranded phones).
Ka.
jockyw2001 great but make one for htc oxygen pls.
htc s710 - rom
confirm this is working very gd
thanks for all yoru help and support to this fourm
hi, i tried the method described and when it runs haret my vox shuts down... and nothing happens, i have to turn it on myself.
madds said:
hi, i tried the method described and when it runs haret my vox shuts down... and nothing happens, i have to turn it on myself.
Click to expand...
Click to collapse
Same here
anyone online right now wanna drop me a line about this... what do I do exactly with the ruu file. Do I place rom image in that folder while runnning update???
so i followed the instructions and executed the cid bypass(installed itsutils and haret). once i get to the end it says use mtty or flash with RUU. so I attempt to flash right after (am I supposed to flash while the screen is black) but its gives me a connections error. I figure its because the phone is off. So I turn it on and update with the RUU again but only make it to 3% before I get a invalid vendor id. Would anyone care to comment on how I can flash this vox to the dopod rom...
madds said:
hi, i tried the method described and when it runs haret my vox shuts down... and nothing happens, i have to turn it on myself.
Click to expand...
Click to collapse
acid74 said:
Same here
Click to expand...
Click to collapse
To the users who had the same problem as me I am currently flashing my phone and I managed to get past my problem by using the SDA Application unlocker on my vox. I always thought that HTC were already application unlocked. Was going crazy for a while but I guess I should've followed the instructions step-by-step regardless of what I thought.
Big up to jockyw2001(and of course pof for without him alot of us would still be using shipped rom) for this wicked tool.
Cheers
neptune said:
To the users who had the same problem as me I am currently flashing my phone and I managed to get past my problem by using the SDA Application unlocker on my vox. I always thought that HTC were already application unlocked. Was going crazy for a while but I guess I should've followed the instructions step-by-step regardless of what I thought.
Big up to jockyw2001(and of course pof for without him alot of us would still be using shipped rom) for this wicked tool.
Cheers
Click to expand...
Click to collapse
Thanx man,last night i figured it out too......hows the dopod ROM??
acid74 said:
Thanx man,last night i figured it out too......hows the dopod ROM??
Click to expand...
Click to collapse
I only got this phone so I could upgrade it for a friend to stop the boot loop. It seems to have fixed that problem so I guess it's better than the other roms. On the other hand I can't stand smartphone's so my suggestion is to ditch your SP and switch to PPC . Also I read before hand that this ROM doesn't include Windows Live Messenger but it is included in the rom. Just thought I'd let u guys know.
input please
Just ran into another problem and would appreciate some input. I understand that USPL only works for one flash...but I wasn't aware that a hard reset counted as a flash. Regardless my device hung at the dopod boot screen after a hard reset. Is this normal after using USPL on a device, and if so does this occur with all devices??? I would hate to give a phone back and have to tell the person that they can't perform a hard reset...
neptune said:
Just ran into another problem and would appreciate some input. I understand that USPL only works for one flash...but I wasn't aware that a hard reset counted as a flash. Regardless my device hung at the dopod boot screen after a hard reset. Is this normal after using USPL on a device, and if so does this occur with all devices??? I would hate to give a phone back and have to tell the person that they can't perform a hard reset...
Click to expand...
Click to collapse
If you flash a full ROM the SPL is overwritten with the one in the ROM (Dopod = 1.19). Nothing to do with USPL. Booting can take a long time after hard reset. Unplug battery and try again.
jockyw2001 said:
If you flash a full ROM the SPL is overwritten with the one in the ROM (Dopod = 1.19). Nothing to do with USPL. Booting can take a long time after hard reset. Unplug battery and try again.
Click to expand...
Click to collapse
Thanks, I got it to work eventually...Good to know USPL doesn't effect hard resets, I guess you learn something new everyday.
If I had to take a guess before hand I'd figure a SP would boot faster than a PPC, but I realize now that I'd be wrong...
thanks to all for the help, I can finally return this Vox back to its owner
cheers
Hi
I flashed my E650 in French with the swissrom (present on FTP), all works !
an idea to change the logo operator to HTC original ?
thanks
thought I fixed the problem. seems as if after a day it just hangs at the dopod screen. It was working fine everytime I had it. As soon as I give it back it seems to hang. Guess ima just flash it back to the HTC rom, too much hassle for just $20.
why SDA_ApplicationUnlock.zip can't unlock my Orange SPV E650?
Successful rom flash done on a spv e650 on a sim unlock device UK orange
Need anyone help to un-brick my Tilt.
Have a fresh AT&T 8925 and did following.
- Got offical unlock code from AT&T and done with unlock
- HardSPL v1 (Works and show the correct SPL version when on tri-color screen)
- Install Radio ROM only version 1.64.08.21
Flashing say successful but cannot bootup.. Still be able to see the AT&T splash screen but never see Windows Mobile bootup screen and screen goes black.
I checked the forum late after and found it is only support with WM 6.1 which i beleive it is the issue i have.
Can I have anyway like bootup mode to restore original Radio Rom 1.27.12.11 or just flash any WM 6.1 cooked rom to solve it.
flippy_tv said:
Need anyone help to un-brick my Tilt.
Have a fresh AT&T 8925 and did following.
- Got offical unlock code from AT&T and done with unlock
- HardSPL v1 (Works and show the correct SPL version when on tri-color screen)
- Install Radio ROM only version 1.64.08.21
Flashing say successful but cannot bootup.. Still be able to see the AT&T splash screen but never see Windows Mobile bootup screen and screen goes black.
I checked the forum late after and found it is only support with WM 6.1 which i beleive it is the issue i have.
Can I have anyway like bootup mode to restore original Radio Rom 1.27.12.11 or just flash any WM 6.1 cooked rom to solve it.
Click to expand...
Click to collapse
Flash to one of the shipped ROM's that are located in the Kaiser Wiki.
Try the one w/ the radio 1.27.11.31
Press the camera button and Reset button to enter Bootloader mode, then reflash your Radio ROM =) !
*Note: Flash a rom compatible for WM6
I am trying to Hard Reset now and showing up something now, not sure it work or not. If not.
Can I any guideline to read how to flash Radio Rom under Bootloader mode. Thanks...
Just enter to Bootloader mode.
In pc:
Make a folder with the radio rom and the Kaiser customRUU on it.
Then connect the phone to the pc.
In pc:
Run kaiser RUU...
***Flashing***
Done!!
now it Must work.. =)
Saludos!
Hi I love this site. I need some help i did plently reading on roms n flashes and tried plenty out. My Question is that i have an htc 8125 phone which is unlocked and has windows mobile 5 on it and is is ilp 1.05 spl 3.08. I wanna put windows mobile 6 with the touch flow and cube but so far I ain't able.
I tried out TNT_5.0_Wizard_TouchFLO and NBK 9 on the Tnt i did it with active sync. I noticed on using TNT at starting my phone on i Get a TNT windows mobile 6 screen then when the phone boots up it customizes cingular and im back with windows mobile 5.
anyway to put windows mobile 6 and touch flo.
thanks for the help
When downgrading your phone so that you can unlock it - you need
Both IPL and SPL @ 1.XX
Yours are not the same - so you need to redo the process to get these two numbers to match. Flash the button rom.
Then, you need to flash a stable oem rom - like the Tmobile 2.26
In order to flash WM6 roms - you need ipl and spl of 2.XX or greater.
You've mentioned that you did some reading - do a little more. Read the unlocking and flashing a wizard posts, follow each step - do not skip any. Take your time, the how to's are very detailed - but they are bang on.
Good luck
htc 8125 problem!
Hi that such I have written for several sides asking the same thing, which happens it is that I have a htc cingular 8125 and need the help someone who can devote a solution to the problem that on having connected my htc to the pc, the activesync it synchronizes well and habia could before formatting the memory could spend(pass) of quite files etc.. But now after erasing I want to install any rom and it turns out that the rom does not recognize the htc, me mistake and the this battery 100 % loaded, the cable in good conditions, I changed the framework into the last one to the pc etc.. And nonetheless I could not have installed the rom.. not that to do.
Thanks...sorry for my bad english.
Is your phone a G3? Install SuperCID.
Is your phone a G4? Run HardSPL.
Once that is done, you should be able to load the Wizard Love ROM.
Then, you should be able to load any WM6 ROM from these boards.
Hi,
I downloaded Official WM 6.1 Upgrade from HTC http://member.htc.com/downloadfiles....0_radio_sign_25.83.40.02_1.65.16.25_Ship.zip
and after running that... My system is dead slow and also unable to install few program like Schap's Advance Configurator etc and other issues like
System Reboot time increases....
GPS taking too much time for a Fix
Menu Pop down slowly...
Stucks quite often
.... And after every hour or so the Message popup like that " Please Inform Microsoft about this issue ...... "
Since i am not a computer Geek... Please advice some simple solution ...
Though i also download the official RUU from HTC which released on 21-2-08 but when i run that it tells me that " THIS UPDATE IS NOT FOR YOUR DEVICE " after the SPL screen...
So, is there anyway that i revert back to original System dated 28-8-07
Ur help in this would be highly appreciated....
And PLEASE accept my appologies is this issue has already been raised here...
not sure what you mean by dead slow. First off, the warning that you get that the rom isn't for your device tells me you are not CID unlock. You can always CID unlock your phone and then put it back to the original SPL if you want to keep things back to normal.
Thanks for the reply.....
thomassster said:
not sure what you mean by dead slow. First off, the warning that you get that the rom isn't for your device tells me you are not CID unlock. You can always CID unlock your phone and then put it back to the original SPL if you want to keep things back to normal.
Click to expand...
Click to collapse
Well it takes time to respond to the command... e.g. if i click on the START then it took quite a time for a menu to pop down....... as far as CID unlock... i am not sure....
But i purchased my tytn II from UK as a sim free unit @ 455 pounds... and before that WM 6.1 upgrade, i never played with the ROM or firmware... no SPL nothing anysort run on my unit.... I just run the RUU directly from PC and follow the on screen instructions....
which spl are you using ?
kuzco1 said:
which spl are you using ?
Click to expand...
Click to collapse
currently in Bootloader it shows...
KAIS130
SPL-3.28.0000
CPLD-8