So i try to upgrade my rom with an official tmobile rom, i've got the mda mini, and it didn't work, it stopped midway saying that an error occur while upgrading the radio stack, now i try different rom, different download of the same different rom, nothing seem to work, it alway stop at 20% of the radio upgrade and tell me that an error occur and that i have to reboot my device and try again, i search many hours on the forum to see the same problem, but i found nothing, is my mda dead, i kinda like it very much, so small, so cute with a winamp skin on the player it was putting a shame to every i pod i know off,
please I'm begging you, help me revive my poor Mda, i even bought a bluetooth stereo head set just for it, too enhance the ipod killer theme.... tell me i didn't do this for nothing !!!!
thank you
I guess it's realy dead
oky, no more chance for this poor mda,
I will have the ceremony down tonignt then i will burn it and spreed the ashes over internet.
Sigiel said:
oky, no more chance for this poor mda,
I will have the ceremony down tonignt then i will burn it and spreed the ashes over internet.
Click to expand...
Click to collapse
Bad news, my PDA likes yours, it cannot flash any rom now...
It's possible to revive them...but you'll need a special SD Card Image ROM...
Google a little bit about .nbh images, SD Rom Boot images, etc.
Once you have this special SD Card ROM Boot image prepared, you put it on the phone, put the phone in bootloader mode (camera + power + reset),and check the screen: - a message will appear telling you to "press power to flash", and you do it. Let it flash and reboot.
Magician revived.
Best Regards,
Keeper
Keeper said:
It's possible to revive them...but you'll need a special SD Card Image ROM...
Google a little bit about .nbh images, SD Rom Boot images, etc.
Once you have this special SD Card ROM Boot image prepared, you put it on the phone, put the phone in bootloader mode (camera + power + reset),and check the screen: - a message will appear telling you to "press power to flash", and you do it. let it flash and reboot.
Magician revived.
Best Regards,
Keeper
Click to expand...
Click to collapse
The file header of the SD Card ROM must be the same of my magician ROM, isn't it? Now the problem is I can't get the header of my magician ROM, when I use "d2s" command the magician dead.
Well i don't quite get what you mean by "header of Magician ROM"....i assume that you are refering to the bootloader...what version do you have? Does it says 1.2 or 1.0? Have you tried to flash a different bootloader from a different model or something?
Anyway, I don't quite get what is your problem exactly - Is it with the Radio part or windows part? Does the WM2003se boots or not ?
- If your problem is only with the WM2k3 not booting, then you must upgrade only with a ROM image for the OS (nk.nbf) - (Try and use an original ROM first...don't you use cooked ROMs.)
- If it's both WM2K3 and radio, then you need to put the nk.nbf and radio_.nbf on the same directory where the MaUpgradeUt.exe is.
- If you also want to upgrade your Extended ROM, then beside both files mentioned, you also need to have the ms_.nbf.
Anyway, regarding the radio part: try this: google for "MagicianRadio_1.13.00_maupgrade"
Finally: don't forget that you need to download and use the "MaUpgradeUt_noID.exe" or the magician will complain about the country code error + some BS.
Best Regards,
Keeper
I heard that the front 416 bytes of SD card ROM image must be the same as the PDA, and then can falsh it. The front 416 bytes of every PDA ROM are different, so I must get my magician ROM header (416B), but I cannot.
My magician can boot, but cannot be flashed a new rom. The error code returned to me is "Get Device Data Error".
btw, the bootloader is v1.02, how can I reflash a new bootloader? I don't know how to do that, maybe it can resolve the problem.
Forget about changing the bootloader - you could end up with a brick on your hands...besides, that's the latest (final?) version of the bootloader for magicians.
Anyway, that message seems to be related to usb data transfer between your pc and your phone...you DID disabled the "Allow USB Connections" on ActiveSync BEFORE TRYING to do an upgrade, didn't you?
If you use windows Vista, there's a known problem when trying to flash a new ROM with it...
check this link on how to use vista for ROM upgrades: http://mahmood1.com/upgrade_pocket_pc_ruu_in_vista.aspx
Best Regards,
Keeper
My system is Windows XP, thank you all the same.
Okey, try this:
1) Download this image: http://www.t-mobile.nl/zakelijk/media/download/MA_TMNL_11300_132_11200_Ship.exe
(It's an original image from T-Mobile).
2) Extract the .exe content using winrar.
You will get the following files:
- EnterBL.exe
- GetDeviceData.exe
- RUU.dll
- RUU.conf
- UI.dll
- ROMUpgradeUt.exe
- nk.nbf
- ms_.nbf
- radio_.nbf
3) Delete the ms_.nbf, radio_.nbf and ROMUpgradeUt.exe files.
4) donwload this file: ftp://xda:[email protected]/Magician/Tools/MaUpgradeUt_noID.exe ...and put it on the above directory.
5) disable ActiveSync "allow usb connections".
6) put your phone in bootloader mode
7) run MaUpgradeUt_noID.exe and let it finish. (It may take some time...)
8) hard reset your phone.
Now, if you want to try to upgrade just the radio, repeat the above steps but delete the nk.nbf from that directory and and put a radio_.nbf there.
NOTE: You WILL loose everything that you've got stored on your phone...contacts, sms, etc...so do a backup 1st if you want.
Regards,
Keeper
It not worked. The RUU.log is this:
00:01:01:890 [msg] : Version : [1.5.0].
00:01:01:890 [msg] : Config Info : [776571],[1],[1],[0].
00:01:01:890 [msg] : RadioFile Not Exist !
00:01:01:890 [msg] : MSystemFile Not Exist !
00:01:05:703 [msg] : Current Not in CE Mode or in CE Mode but ActiveSync Not Connected.
00:01:09:828 [msg] : Disconnect ActiveSync .... [2]
00:01:09:968 [msg] : Current in BL Mode. Open Port : [\\.\WCEUSBSH001] OK.
00:02:48:281 [err] : BL Get Device Data Error.
00:02:48:281 [msg] : Update Image. CE : [4], MSystem : [0], Radio : [0]
I clicked "Upgrade" and it displayed "checking the information of your device..."...
Okey...the only way i see it, is to try an SD Card Upgrade.
I can try and craft you an image for your SD Card but i don't know if it will work on your SD Card... What's the size(s) of your SD Card (s)?
I don't want to e-mail you 1Gb image (i only have 1 and 2Gb SD Cards) and has so i need to do this ( http://buzzdev.net/index.php?option=com_content&task=view&id=18&Itemid=41 )...which i've never tried...so let's hope that the SD Card header won't be a problem...
Anyway, i can't do it now...i'll pm you later on, when i get some free time.
Regards,
Keeper
Thank you.
I have a 2 GB SD Card, but it didn't work, I think the reason maybe the header of the SD Card Image not modified. But I cannot get the header of my PDA.
Okey, here we go.
Do this:
1) Download this Emergency SD Card image: http://rapidshare.com/files/56985459/Emergency_SD_Card_Image.rar.html
2) Download the NTRW in attachment
3) Format your SD Card using windows XP format option
4) Copy both files (ntrw.exe and SDCard.img) to your C:\
5) Open a dos command prompt and type: ntrw write SDCard.img <sd card reader drive letter>
( do note that <sd card reader drive letter> must be replaced with your own SD card reader drive letter...example: "ntrw write SDCard.img e:". Also do note that when writing to the SD Card, some errors might appear...ignore them...the image is/will be there in your SD Card)
6) Put your phone in bootloader mode
7) Connect the usb cable or power cord to your phone (This is a MUST! or you won't see the next step)
8) Insert the SD Card on your phone and check if the screen message changes to something like " Press power to flash "
9) Do has told: press the power button and WAIT! (if it seems to stop, leave it that way...it will eventually end the upgrade)
10) Hard reset your phone when the upgrade ends.
Note 1: This SD image and procedure was tested on my phone and it works. The image itself is an original T-Mobile ROM 1.13.
Tell me how it went.
Best Regards,
Keeper
Happy to hear you again. But I cannot download the image. I will try.
I do this step by step, but after I inserted the SD Card on my phone, the screen message didn't change, it was "USB V1.02", if I disconnected the usb cable, it changed to "Serial V1.02".
It can't be...This image is in perfect shape. you must be doing something wrong or your bootloader is damaged seriously...
check this out:
- Your USB cable must be connected to your PC and ALSO to the Magician.
- Check if ActiveSync USB option is disabled.
- If both of the above are true, leave the SD Card inside the mini, and press camera + power + reset button again...(i've read that sometimes the process doesn't work at the first time...)
- Try to disconnect and connect the USB cable from your magician, with the SD Card inserted on the phone...check is the message on the screen changes...
Please post what you have tried already...
If nothing works, that means that your bootloader is f* up. You'll have to wait a little bit more so to give me time to check how to prepare an SD image (or an alternative way) for upgrading your bootloader.
Keeper
It not worked.
I just did as what you said. If I pressed camera + power + reset button with the SD Card inside, the screen was not changed even if I connected / disconnected the usb cable; but if I pressed camera + power + reset button without the SD Card inside, and inserted SD Card under bootloader mode, the screen can change from "USB" to "Serial", but I didn't see " Press power to flash ".
I think my Magician bootloader was corrupted, because the screen showed nothing after I typed "d2s" in MTTY. But I don't know how to upgrate bootloader.
Thank you very much.
Now I find a new problem: I couldn't delete some fonts files stored in "/storage/fonts", even if I hard reset PDA. After I setup a new font named QooQooCN, I cannot uninstall it, seems wince.nls running. But I still cannot delete /storage/fonts/*.ttf files. Why? If this is the reason why I cannot reflash my PDA?
Need help.
Coly, here it is the 1.02 bootloader from my device. Put it on your formated sd card like explained previously. Reboot in bootloader mode with the sd card inserted and with the USB cable connected...see if now you can get the "press power to flash"
If it still doesn't work, we will have to crack the passwords for the bootloader debug mode.
anyway, post your results, please.
Keeper
Hi Im Using Xp Pro
THIS IS WHERE IM UP TO .SORRY IM NOT USED TO FORUMS.NEWBY.[please scroll to bottom of page]
The exe has created a folder on your C drive called Unlocker. There are 2 folders inside that one called kaiser-HardSPLv1 and one called kaiser-simunlocker
Note for Vista users
===============
If you do not have the latest version of Mobile Centre follow This guide to explain how to change your drivers to the xp. You will have problems running the unlocker otherwise. Log in as administrator if you run the ROM update tool and unlocker. That also applies to XP users.
Instructions
============
1. Install HardSPL as per the instructions:
1- Connect Kaiser to computer using USB cable
2- Make sure ActiveSync icon is GREEN
3- RUN kaiser-hardSPL.exe on Computer (PC)
4- Follow instructions on screen
To check it has installed correctly, power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-colour screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.27.14.09") (Or by going to Start, Settings, System, device information). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. (If you have a UK Orange Tytn II with the radio version 1.27.12.29, Use Radio version 1.27.12.32. Keep a note of the unlocking Code as you will need to enter it again after you have re-flashed the Radio.) (You will find download links at the bottom of the instructions)
3. Connect PC and Kaiser with a USB cable and keep it connected until the last step.
4. Power on the Kaiser and let it boot into Windows Mobile. On the PC make sure the activesync icon is green
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run KaiserCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished.
6. Power off your Kaiser and insert a different SIM, i.e. a SIM from another provider than the one your phone is locked to. (if you have a pin on the sim disable it first)
7. Once Windows Mobile has booted up it will (usually after you have entered the usual 4-digit PIN) show a window called "Simlock" and a textbox where you can enter a 8-digit unlock code. Now perform a soft reset by pressing the reset button *but* at the same time keep the camera button pressed. If you did it well you will be back in bootloader mode and you see the tri-color screen. The best technique is to press and hold the camera button first and then shortly press the reset button with the stylus.
8a. right-click activesync icon and uncheck "Allow USB connections" from Connection Settings
8b. On your PC, go into the "step2" directory and run "kaiser-simunlocker.exe". If all went well you will see the unlock code on your monitor and your Kaiser is being restarted
MY KAISER DOES NOT RESTART and stays in tri mode AND THERE IS NO PASSWORD ON SCREEN.THANKS AGAIN
mattdehat said:
HI,ive been installing sim unlock on my tmobile kaiser and at a certain point i get a problem,after tri-screen after soft reset with camera button pressed,on screen i get this
===kaiser sim unlocker[c}2008 by jockeyw2001
===donations happily accepted. paypal to [email protected]
WITHOUT THE PASSWORD.CANT UNDERSTAND IS SHOULD HAVE A PASSWORD AND AS EVER NOT HAPPENING FOR ME
ANY HELP WOULD BE APPRECIATED.THANKS
Click to expand...
Click to collapse
are you using vista? could you be a bit clearer on things? less caps?
Hi Im Using Xp Pro
THIS IS WHERE IM UP TO .SORRY IM NOT USED TO FORUMS.NEWBY.
The exe has created a folder on your C drive called Unlocker. There are 2 folders inside that one called kaiser-HardSPLv1 and one called kaiser-simunlocker
Note for Vista users
===============
If you do not have the latest version of Mobile Centre follow This guide to explain how to change your drivers to the xp. You will have problems running the unlocker otherwise. Log in as administrator if you run the ROM update tool and unlocker. That also applies to XP users.
Instructions
============
1. Install HardSPL as per the instructions:
1- Connect Kaiser to computer using USB cable
2- Make sure ActiveSync icon is GREEN
3- RUN kaiser-hardSPL.exe on Computer (PC)
4- Follow instructions on screen
To check it has installed correctly, power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-colour screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.27.14.09") (Or by going to Start, Settings, System, device information). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. (If you have a UK Orange Tytn II with the radio version 1.27.12.29, Use Radio version 1.27.12.32. Keep a note of the unlocking Code as you will need to enter it again after you have re-flashed the Radio.) (You will find download links at the bottom of the instructions)
3. Connect PC and Kaiser with a USB cable and keep it connected until the last step.
4. Power on the Kaiser and let it boot into Windows Mobile. On the PC make sure the activesync icon is green
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run KaiserCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished.
6. Power off your Kaiser and insert a different SIM, i.e. a SIM from another provider than the one your phone is locked to. (if you have a pin on the sim disable it first)
7. Once Windows Mobile has booted up it will (usually after you have entered the usual 4-digit PIN) show a window called "Simlock" and a textbox where you can enter a 8-digit unlock code. Now perform a soft reset by pressing the reset button *but* at the same time keep the camera button pressed. If you did it well you will be back in bootloader mode and you see the tri-color screen. The best technique is to press and hold the camera button first and then shortly press the reset button with the stylus.
8a. right-click activesync icon and uncheck "Allow USB connections" from Connection Settings
8b. On your PC, go into the "step2" directory and run "kaiser-simunlocker.exe". If all went well you will see the unlock code on your monitor and your Kaiser is being restarted
MY KAISER DOES NOT RESTART AND THERE IS NO PASSWORD ON SCREEN.THANKS AGAIN
so what step did you get up to?? you didnt really need to paste the whole instructions as most of already know the steps.
hi.istarted fresh.phone now unlocked.many thanks to all.I LOVE THIS SITE...MOST INFORMATIVE.MANY THANKS AGAIN
I got stucked into a Multi dotted colored screen with my Kaiser8925, and I can´t flash the old radio versión, I got the file, but I try to flash my kaiser, and it gets not installed, I think the new radio version I flashed is causing the problems. ¿Can you help me?
josereja said:
I got stucked into a Multi dotted colored screen with my Kaiser8925, and I can´t flash the old radio versión, I got the file, but I try to flash my kaiser, and it gets not installed, I think the new radio version I flashed is causing the problems. ¿Can you help me?
Click to expand...
Click to collapse
Thread hi-jacking is not very good...also posting the same thing in multiple threads isn't either...But, try reinstalling your Windows rom...Sounds like thats the issue. Could be something more severe though.
Hello there,
I am rett new on this forum and i must start by commending the developers. my phone looks and works so much faster.
i have a HTC Tilt Kaiser.
one problem.....
i dont get sound for my calls and i have to do a soft reset and i only get sound on one call any subsequent calls made/or received dont have Sound. this is on the headset itself, via Bluetooth, via wired handsfree set.
i have tried to load the following ROMS all with the ame results.
- AthineOS_B.23004.rar
- Ultimate-X.V8.2G
- TPCV7FULL
- TPCV6.1FULL
- HTC_HERMES_S64_WM_6.1_UC_V6_06.08.2008 [wont allow me to go back to this.]
- JumpSPL1.56-KAIS
- Copied AudioPara3 to the Windows dir but still no fix.
have run the Kaiser unlocker after JumpSPL1.56-KAIS but none of these fix the issue.
i folloed the istructions on http://forum.xda-developers.com/showthread.php?t=433835
Flashing via ActiveSync with USB Lead
1. Copy JumpSPL1.56-KAIS.exe, JumpSPL1.93-KAIS.exe and JumpSPL1.94-KAIS.exe to your device memory (NOT STORAGE CARD)
2. Pull out the battery and reinsert it (this step IS important) *DONT turn phone back on yet*
3. REMOVE SIM and SD CARDS!!
4. Turn phone back on and let it boot back into your operating system
5. Connect your phone to PC with a USB cable and wait until it syncs with your PC
6. Run File Explorer on your phone, browse to where you copied JumpSPL1.56-KAIS.exe on your device and run it (make sure the USB cable is still connected). If you get a white screen then reset your device and now try JumpSPL1.93 and lastly try JumpSPL1.94 if that one doesnt work.
7. CLick Continue on phone when prompted
8. After a few seconds the tri colour screen will appear on the phone and "USB" will be displayed at the bottom
9. Unplug the usb cable for 30 seconds and then Replug (phone will not re-sync but still says "USB" on the screen)
10. Right click on the Activesync icon in the bottom corner icon on the computer, goto connection settings, deselect "Allow USB connections" and click "ok"
11. Run the KaiserCustomRUU.exe file on your PC thats in the same folder as the HardSPL .nbh file and follow instructions (ticking boxes and clicking Next) *DO NOT re-enable USB Connections in Activesync*
12. Update will goto 100% (should take less than a minute), the Congratulations screen will be displayed on the PC and the phone will restart
13. Unplug USB cable from phone then REPLACE SIM and SD CARDS !!
14. Restart phone
*Remember to re-enable "Allow USB connections" in Activesync connection settings after a successful flash*
What am i doing wrong and is there a patch to fix this?
sounds like its your radio. flash different radios until everything is normal again.
try 1.65.24.36 niki radio..
I had this issue too...going through the process for the first time. After going thru the unlock, I had to go back and flash the stock HTC/Tilt 6.1 rom...then flashed the one I wanted. All's well.
Try a new radio...
And please read / search before starting a new thread. If you can't find the answer, post in the relevant thread instead of starting your own.
Dave
I was trying to flash my phone to a diffent ROM< but now everytime that i have tryed, it gives me an error - get newer updater. I have used CUstom RUU V. 1 that comes with most roms, and i have used the 5.22. The Hard SPL version is 1.00liPof. Help!!!
I think you may have the wrong section, what phone are u using, i dnt thats a kaiser hardspl
Hard SPL 1.00lipro is a hardspl for the kaiser, i have it on my kaiser. Although the 5.22 he refers to i have no idea what they mean?
Opening poster try to explain in more detail what it is that you are trying to do, i.e. what rom it is that you are trying to install, what windows you are using on your pc etc.
If you cant use that ruu try this one i attached
Ah i see, ive never really had that problem even though ive flashed on xp, vista and 7. Very weird. Try changing Hardspl.Good Luck and use the ruu that has been given here
had that problem
When i switched to windows 7 i had a similar issue. There should be an update now that you plugged your phone in to the c. Try to see if there is a windows update that shows up now.
Hi,
Or Even try to mount a virtual machine in Xp with Vmware or similar...
Good luck
Sat
Update your hardspl to 3.29 or 3.34. The spl you are using is for WM 6.0
http://forum.xda-developers.com/showthread.php?t=498320
sd
flash via micro sd. easy, faster, gets rid of a middle man. and update your spl.
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Kaiser Rom Develpoment Page and unzip/unrar it to your computer
3. Goto the Roms Folder and rename the .nbh file to KAISIMG.nbh
4. Copy the KAISIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Hold in the Power and Camera buttons, then press the reset button with the stylus for about 3 seconds until the BootLoader screen appears
7. You will first see a tri-color screen with the phone and SPL Information at the top
8. A message will then pop up asking you to press the Power button to start the update
9. Press power button to start flashing
10. Once phone finishes flashing and says Update Complete, reset with the stylus
11. When it gets to the screen where it configures the stylus, HARD RESET
(press left and right softkey buttons on the front and hold in reset with stylus until message appears)
12. When prompted, Press "Send Button" (Green Call Button on Front) to Clear Data
13. When prompted, Press "Send Button" (Green Call Button on Front) to Restart Phone
14. Follow onscreen instructions to set up your New Rom
(from http://forum.xda-developers.com/showthread.php?t=433835)
i use windows seven and have never had any issues flashing roms?
A few kitchens dont work in seven though, so building is a bit hit and miss but flashing has never been a problem
Hi it seems like I need to do a new thread for this, I just need answers thank you
*upon checking my phone
I have this
ROM Version: 3.29.707.0 WWE
ROM Date: 05/07/08
Radio Version: 1.65.16.25
Protocol Version: 25.83.20.02H
and as I learn to check what Hard SPL is installed in my device (thanks to you guys ) it says 3.29. 0000 or something like that, so my question is... does my phone already have been flashed? if so can i skip to to loading the Rom i wanted, i do need help thanks
if not this is from mskip
1. MAKE SURE YOUR KAISER HAS AT LEAST 50% BATTERY POWER FIRST
2. Download and Unzip *THIS* File
3. Flash HardSPL 3.29 [ESSENTIAL]
Flashing via ActiveSync with USB Lead
1. Copy JumpSPL1.56-KAIS.exe, JumpSPL1.93-KAIS.exe and JumpSPL1.94-KAIS.exe to your device memory (NOT STORAGE CARD)
2. Pull out the battery and reinsert it (this step IS important) *DONT turn phone back on yet*
3. REMOVE SIM and SD CARDS!!
4. Turn phone back on and let it boot back into your operating system
5. Connect your phone to PC with a USB cable and wait until it syncs with your PC
6. Run File Explorer on your phone, browse to where you copied JumpSPL1.56-KAIS.exe on your device and run it (make sure the USB cable is still connected). If you get a white screen then reset your device and now try JumpSPL1.93 and lastly try JumpSPL1.94 if that one doesnt work.
7. CLick Continue on phone when prompted
8. After a few seconds the tri colour screen will appear on the phone and "USB" will be displayed at the bottom
9. Unplug the usb cable for 30 seconds and then Replug (phone will not re-sync but still says "USB" on the screen)
10. Right click on the Activesync icon in the bottom corner icon on the computer, goto connection settings, deselect "Allow USB connections" and click "ok"
11. Run the KaiserCustomRUU.exe file on your PC thats in the same folder as the HardSPL .nbh file and follow instructions (ticking boxes and clicking Next) *DO NOT re-enable USB Connections in Activesync*
12. Update will goto 100% (should take less than a minute), the Congratulations screen will be displayed on the PC and the phone will restart
13. Unplug USB cable from phone then REPLACE SIM and SD CARDS !!
14. Restart phone
*Remember to re-enable "Allow USB connections" in Activesync connection settings after a successful flash*
Flashing via MicroSD Card using cmonex HardSPL 3.29 [OPTIONAL]
FOR UPGRADING HARDSPL ONLY!! THIS WONT WORK UNLESS YOU ALREADY HAVE HARDSPL ON YOUR PHONE
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download Cmonex's HardSPL 3.29SD, unzip it and copy the 2 files into the root of your MicroSD Card
(KAISDIAG.NBH is basically an SSPL patched to load from SD without booting OS)
(KAISIMG.NBH is cmonex HardSPL 3.29)
3. Insert the microSD Card into the phone
4. Hold in the Power and Camera buttons, then press the reset button with the stylus for about 3 seconds until the BootLoader screen appears
5. It should say Loading / Update in progress and then to a screen saying SPL 1.00.OliNex
6. It should now say Press Power Button to flash or just flash the KAISIMG.NBH and then reset
7. At this point it should boot to the OS, if it doesn't then flash an OS (delete the previous KAISDIAG.NBH and KAISIMG.NBH from the SD Card and use Flashing Rom from MicroSD Card method)
8. After the Operating System loads, DELETE the KAISDIAG.NBH and KAISIMG.NBH files
*To check HardSPL version on your phone Enter Bootloader by Holding in the Power and Camera buttons, press the reset button with the stylus for 3 seconds until the tri-colour screen appears, then read the 2nd line which is the SPL version*
4. SIM and CID-Unlock [OPTIONAL]
For more reading go *HERE*
* YOUR DEVICE MUST BE SYNCHED WITH YOUR COMPUTER BEFORE RUNNING EACH STEP *
*Put your phone into Bootloader and update to a 6.1 Rom first if you get a black screen after Flashing the Patched Radio*
*If the program wont run u may need to install Microsoft .NET 2.0 on your computer to get it working*
1. Make a note of your current Radio in case you need to flash it back
2. Run KaiserUnlocker.exe, follow the instructions
(if you already have HardSPL on your phone you can skip straight to Step2)
3. After patched Radio has been flashed phone will restart and sync with the computer
4. On the Unlocker Program it should say Radio Patched at the bottom
5. Click on Step3 (Run Unlocker). This will bring up the Unlocker screen on your phone
6. If you want to check the status of your Sim Lock or CID Lock click the appropriate buttons
7. Click on Remove Sim Lock and Set CID, then click "Commit Changes"
* IF YOU DONT NEED TO FLASH A NEW ROM THEN PROCEED TO STEP6 TO PUT YOUR DESIRED RADIO BACK*
Click to expand...
Click to collapse
are the instructions from flashing hard spl 3.29 below it or what? I'm just confused coz' I found this tutorial here in the forums also http://forum.xda-developers.com/showpost.php?p=2498297&postcount=10
Im just confused thanks
If you are confused, stop.
Re-read again and again, until it makes sense. Understanding the huge material around here is not to be taken in only one day.
I spent my early days 2 weeks by merely reading, collecting tools (and patches) before even attempting to flash.
I just needed an answer if my phone's already flashed that's it if it is flashed could i skip now on flashing my desired rom? that's just it, just answers from experts. I'm reading btw.
any help will do
On bootloader will say Hard if have hard-spl.
You could have asked in teh thread rather than starting new so as to keep forum clean.
On that note thread closed.