Database Info

Problems with Plantronics M3000 and QTEK 2020

I have bought a Plantronics M3000 bluetooth headset for my QTEK 2020. I have no problems pairing, calling and answering. However the headset just shuts off after a few minutes of conversation. It doesn't just cut the conversation but shuts off. I can make multiple short calls but nothing longer than 3/4 minutes. It works, however, without problems on my wife's Ericsson T68. Anyone can help ? Thanks.
Marek

Hello,
I have the MDA2 (same as QTek2020) and a Plantronics M3000 and It's been working just fine.
The problem you describe it's very weird since you mentioned that the headset works fine with your wife's mobile, and that makes me think that your QTek has some sort of problem with the Bluetooth stack or hardware.
It may be well worth to try (if possible) another headset just to make sure that is not the M3000 fault.
Do you see any type of error or message on the screen at the time of disconnection?
Does it always cut the conversation at the exact same moment?
Does the problem match the time the QTek takes to power save?
Any other clues?

Thanks.
I did not have the occasion to test another BT headset on the Qtek. When it shuts down there isn't any message displayed.
I have no problems with the BT stack (with the Pocket Bluetooth Tools patch) when using it with a BT GPS (Emtac) receiver, it works for hours.
However, your suggestion that it might happen when the Qtek goes in energy saving mode is interesting. I will check that tomorrow.
I'll post the result.

Hi
I seem to have a similar poblem after installing pocket bluetooth tools!.
I use a Jabra BT 250..and I noticed that the headset just mutes during the call..
I am generally used to switching off the display of the XDA after placing the call to power save ...
So I discovered that the headset would mute whenever i switch off the xda after making the call (which it never did prior to installing PBT)!
any thoughts on that?
maybe it has to do with the auto switch off plugin?

Actually I just experienced that too...
If I place (or answer a call) the next time I try to use the phone via the BT headset I notice the BT headset was turned off... Yeah, it could be related to the Powersave feature on the today plugin that PBT installs as a plugin... :roll:
Need to investigate...
Best regards,
Rayan

Both my bt headsets have stopped working since installing pocket bluetooth tools latest version, I have reverted back to version 1005 and everything is fine. I have a sony-ericsson EBH-65 and a skypower clip on headset.

my platronics does the same also its annoying you cant even transfer the call back to the device you have to hand up turn off bt and then turn it abck on and headset mode back on it also does the same on my pc
when im on msn using it as a headset it just d/c and i have to turn it off and turn it back on again
dont see what the problem is
btw the range on the xda2 and platronics is amazing i had it on my bedrooms desk and i went outside it passed through the living room wall and the patio window and i was stood 5m down my garden im sure it would of been over 10m and it was still working if i kept still when i moved it went crackly but ah well lol
just hope someone sorts the prob out

Hi,
I was having the same problem with the M3000. I just had confirmation from Plantronics that this problem is a bug in the product that occurs with the XDA II. I am currently in the process of returning the product.
Regards...Mike

Same problem M3000 doesn't work. Give up now before too much frustration makes you feel ill.
Try the Hello 2 headset. Work with my Aussie XDA2 and is very small and lightweight. Even had a neck chain to carry it around like a USB drive.

Bluetooth Handsfree Connected, but no sound

Hi if someone can help me it would be much appreciated. I just bought a Touch Pro and everything is working fine....except for one really annoying issue.
Whenever I connect my bluetooth to a headset, it shows connected but no sound is coming out. The sound is muted. when connected to my Audi, I see that the phone has bars (shows connected and I can dial the phone), but when I make a call no sound. Similarly on my SE HBH-DS970 headset. The A2DP works perfectly, but when I make a call nothing.....I've searched google and through XDA and no solution.
Can someone suggest a solution? I've soft/hard reset the device already. If I should change Radio ROM which one would someone suggest that's stable? Thanks

If no one else has this problem, can anyone at least suggest to me if this sounds like a Hardware or software issue? If hardware I will return it, but if software I will try to find a solution. Like I said the phone connects to BT, but I just can't get handsfree to work. File transfers and A2DP work. Thanks

Just flashed to UK ROM and still no help....I've read some people having the same problems over at the Diamond thread...I'm the only one answering my own thread here hahaha....if anyone can help I'd greatly appreciate it. Thanks.

Hi,
I occasionally had such an issue with my Parrot CK3100, but I did not get the time yet to investigate further. After the call was connected I did not hear anything, and I am not sure whether the other party could hear me.
On another day, the handsfree was working perfectly OK.
Cheers
Michael

Thanks for replying Michael....I'm at a loss and I tried all the suggestions posted. I hope it's a software issue...I'm going to buy a bluetooth headset tomorrow and see if that works. It's not the end of the world, but annoying since all my ppc, s60, BB, and UIQ phones prior to the TP have not had any such issues.
Do you think it's a software issue?

have you tried playing music?

Yes.....A2DP works perfectly....no problems whatsoever with file transfers either....I'm guessing either it's a software problem or the phone has a new bluetooth software that's not agreeing with my older SE headset, but the car is another issue. The Car is 2007 and I'm sure the Bluetooth software is not that old. I've tried Euro WWE and Asian WWE ROM and no go.....I'm going to try the Cingular ROM and see what happens.

Just another quick update....I tried 2 other different bluetooth headsets and still the same problem... for some reason the sound for handsfree will not come through...anyone know of registry hack possibly that will allow sound to come through?

May not be entirely related to your problem...
Mine is worst...whenever I have paired my Jabra or iTech BT headset, when the phone rings, 8/10 times the phone will auto pickup (and no I did not setup the phone to auto pickup) and the it will NOT connect to the bluetooth. Instead it will be just like an auto pickup and the sound will come thru the phone headset. This is driving me nuts!!!!

Enable SMS over Bluetooth?

I have the Kenwood DNX8120 and it works fine with my Fuze (did have disconnect issues but just updated the Kenwood firmware which should take care of that) but the SMS feature on the radio doesn't work. I know only certain phones are compatible with this feature but on the Kenwood compatibility list there are several HTC devices that work. In any case, does anyone know how to enable SMS over bluetooth on the Fuze?
Thanks

I have the Kenwood DNX8120 in my car and have had no luck getting the Fuze to work correctly. It constantly drops connection. I updated the Bluetooth firmware and that only seemed to make matters worse. It will pair with the Kenwood, but either won't make a phone call or will take up to 60 seconds (or not at all) for the Fuze to recognize I it the call button on the radio. SMS, sent and received call history also do not work.
Have you had similar issues?

I can not get sms working. The only other issue I have is that after a call, it drops the connection. If I get another incoming call, it will reconnect and the radio will ring and handle the call. But, if I want to place a call, I have to either select "set as hands free" of something similar, in the bluetooth settings on teh phone and it reconnects and I can dial. I just upgraded to elite rc3 and the problem is still there. I havn't messed with it enough yet to know if it dials ok without having to bring the phone out of standby yet. I too have updated the bluetooth drivers from Kenwood and that didn't help. I also tried the jetware handfree extension and didn't see any improvement.

I called HTC about this, and they told me it only "officially" supports a hand full of car units. Mostly in the Audi and BMW. They don't "officially" support anything from Kenwood so they were absolutely no help on this. I've also noticed this phone drops all connections except cell and data when it sleeps. Wifi, GPS and Bluetooh all seem to go to sleep with the phone. This seems to make bluetooth pretty useless if the connection drops every time the phone sleeps and needs to be manually reconnected.

I haven't seen it drop the bluetooth connection during sleep. I see that the Kenwood supports some HTC devices but not this one specifically. The other wierd thing is that the first time it pairs it shows the battery indicator but after the next connect it doesn't show it. It shows the battery icon but shows it empty. The jetware extension however does fix that. I will play some more with it and report here.

After resetting my phone to AT&T's original setup, I am experiencing the exact same functionality as you. It now sync's my call history and phone book. No voice dial support or SMS yet. (These have never worked with any of my phones) It will disconnect after a couple phone calls and I have to set as hands free to reconnect. Also, mine still looses the connection to the unit when it goes to sleep. I'm keeping it on a car charger for now and turning off any sleep function when charging. That at least keeps it connected until I make a call. It's almost still not worth using with having to reconnect hands free. Maybe if a hands free quick connect shortcut could be created?
This is all really ridiculous that a phone with this kind of tech can't auto pair and be ready for a call. My LG Chocolate had absolutely no problems with the Kenwood. As soon as the Kenwood finished booting the LG would auto connect and be ready for a call.

I thought I found a workaround at
http://forum.xda-developers.com/sho...ghlight=bluetooth+connection+drops+phone+call
But, once installed an trying to run BT Restart I get an error saying that I need .net compact framework (version 1 or 2) installed. Not sure what to do now, cant seem to find a cab for this.

I've used this package from another post on the forum. It has many useful apps including the latest version of .net compact framework.
http://www.tyguy.net/_xchg/PPC/@essentials.rar
Let me know how it turns out!

I will take a look but I have 3.5 already installed. I guess that app needs the older version. Not sure I want to mess with downgrading it.

Not Kenwood
Hey Guys,
I drive a Jag XK8 and it has the same issues you are mentioning with your Kenwood, but its an Alpine unit, it drops calls, and after the first call connects the second call rings on the stereo but you can only answer on the handset.
I also recently had a new Jag XF for a week. It had a full integration to the phone. It also only showed the battery status when the phone first connected then the battery showed empty. It would drop bluetooth connections constantly on some days (every 90secs) and then somedays it would keep the bluetooth connected without issue. Very unreliable.
The reason I bring this up, is just to let you know these issues are not limited to the Kenwood.
Dave

Just an FYI. I have found it easier to just go into setup in the Kenwood and reconnect the bluetooth from there when the phone disconnects. It's under Setup/Bluetooth/Set, then just click on the device and hit connect. It seems easier than fiddling with the phone while your driving.

[Q] Transfering call from bluetooth speakers to phone by tasker, how?

How do I transfer a call from bluetooth speakers to the phone with tasker? Cant find any parameter for tat action :/
Why: When in car I want the calls to go through bluetooth handsfree system, but if its a private call and I have company in the car I would like to be able to pick my phone up from the dock and then the call should be transfered to the phone automaticlt even thou the bluetooth still is connected.
How do I do this?
Thanks in advance
/Max

The way I would do it is have a script to turn off bluetooth when there is an incoming call and it is removed from the dock (by the way what do you mean by dock?) and then re-enabling it when the call ends.

Good thought, but its like walking around the problem. Ill try if my car likes me to switch on and off BT or if it will refuse to reconnect.
Dont need a script for it, tasker have defaults to just turn of the BT in this case. But it would be a hell lot easier if I could just re route the sound since there are buttons for it on the darn phone
A dock... the holder with included charger for my mobile in the car.
Regards
/Max

On htc phones if you answer from the bluetooth the call will take place there but if you will answer from the ohone the call will be directed on the phonespeaker
I also have this problem but in opposite way. I want that when my phone has the autoanswer enabled the call to remain on the bluetooth which is not happenning and when i am riding the motorcycle is difficult to answer from the bluetooth device

lhoria said:
On htc phones if you answer from the bluetooth the call will take place there but if you will answer from the ohone the call will be directed on the phonespeaker
I also have this problem but in opposite way. I want that when my phone has the autoanswer enabled the call to remain on the bluetooth which is not happenning and when i am riding the motorcycle is difficult to answer from the bluetooth device
Click to expand...
Click to collapse
I havnt tried, but this app looks promising for you: https://market.android.com/details?id=com.everysoft.autoanswer
//Max

Thank you, I tried this but is not working as I wish, because when is answering the conversation is transferred automatically on the phone!

Question Watch bluetooth answering calls. Can I change default behavior?

This is driving me a little nuts! The watch frequently defaults to be my bluetooth connection when I'm making and receiving a call. It's mainly when I am in my car and I really NEVER want a phone call on my watch. Is there some way to disable phone calls on the watch or change how the phone is connecting to devices (eg in what order it makes a connection)?

In Settings > Bluetooth > Paired devices > Disable option to receive calls, for watch

I think this may be the best solution for it. I appreciate the quick and easy response! Bummer that it doesn't let me pick the default list in order or something.

Do you have LTE watch ? Because I do not really understand your problem.
Mine is BT. When I get into my car, phone connects to Ford Sync system. When incoming call arrives I just pick it up from the Ford sync.

That is what I want to happen! I do not have lte but when I'm in my car (and I would say more likely than not connected to Android auto) when I press the button to answer the call my watch steals it. It also sometimes happens when I'm wearing BT headphones connected to my phone. The way you're describing it is totally logical. If I answer it on the phone with a swipe or I choose that device in BT settings once a call is already answered that's fine. But when I'm pressing the answer button on my steering wheel why is it going to the watch?

bam099 said:
when I press the button to answer the call my watch steals it.
Click to expand...
Click to collapse
This is really odd.
When I pick up call on the phone, still Ford gets the call.
When out of the car and watch connected to phone: when I pick up at phone - call remains at phone.
The only difference is, that I do not connect to Android Auto ( I have to use cable - which I am to lazy to plug ). I use only BT connection to car as ordinary handsfree
I will verify what happens when I connect to Android Auto.
EDIT: Maybe this is a problem of you phone ? I think this is the place when you shoul search for handsfree priority ? I mean it is not "hungry" watch "stealinbg" the connection buy phone feeding him I have Galaxy M51 and no problem of this kind
EDIT2: You ate not the only one with this problem and it is not problem caused by GW4
android handsfree priority - Google Search

Problem solved:
[Guide] How to use Tasker to fix all calls being sent to Gear S3
The Problem: On many non-Samsung phones, all calls, even when answered on the phone itself, get sent to the watch's speakerphone, requiring the user to manually switch the sound back to the handset every time a phone call happens. As a side...
forum.xda-developers.com