Ok Guys.
I created this thread cause in the JACHero thread on at least every page everyone asks how to install it, what am I doing wrong, and why is it broken.
So let me give you step by steps of what exactly I have done for me and others to run Hero with out a problem. I will also create a thread with step by step on how to use Ubuntu Linux Live distro to partition your card.
Things you will need to make this work.
Your Brain
G1 Phone
SD Card reader
And the files I included in this thread.
My phone right now is running.
JACHero 2.3
NEW SPL
cyanogens recovery 1.2
8gb class 6sd with Swapper(Swap file on ext2 sd)
setCPU slightly overclock.
Results.
Ever since I did my new Buttons, and the SPL I included in this write up, I have not had one problem flashing any hero rom at all on my phone, nor did I ever have problem actually running hero roms.
So here goes.
First before you partition your card or do anything make sure your card is at least portioned to fat32, don't worry about any other partitions yet.
OK once you do that go ahead and take the radio zip file I am including in this thread and flash it on your phone.
But first make sure you don't already have new radio installed which is 2.22.19.26I THIS IS VERY IMPORTANT. To check what radio you have, power off your phone, and power it on while holding the camera button.
If you do have new radio you can continue on to flashing the new SPL.
Flashing your SPL. (PLEASE MAKE SURE YOU HAVE THE NEW BUTTONS INSTALLED)
Ok this is where it might get a little tricky, and you might require a SD card reader I know I did and frankly I think this is the best way to do it and I recommend every time you do put a new update on your sd card to update your phone do it through a card reader.
Now after you flash your SPL you might or I should say more then likely will get stuck at the T-Mobile G1 screen, this also might happen after new radio flash in the previous step. If this is the case do not freak out it's normal and your phone is not bricked, but this is why having a sd card reader is important.
Ok so Here is what you do after you have flashed new Radio and SPL(Note:The steps on running Linux live distro and using it to partition your card is coming up). Boot up Live distro of Ubuntu, when its done booting, go ahead and go into the partitioning program while your sd card is hooked up in the computer.
Go ahead and set up two partitions at this time. One EXT3, and of course the other one Fat32. Your ext3 partition doesn't have to be all that big. I actually have mine set up to 512.
Once you are done creating partitions, go ahead and put the latest JACHero on the FAT32 portion and flash away (don't forget to rename to update.zip).
At this point if you follow all of these steps there is no way possible that your phone should not boot right into the system to run the initial setup.
These steps pretty much walk you through steps as if you were starting with a phone that has completly nothing on it.
Also the first boot up after flashing the new ROM, might take a few mins at the HTC screen.
Once your phone loads up and you go through the setup process go ahead and run swapper, it should be an APP that's already pre-installed.
Once you run swapper go into the setting and change the location of your swap file from /sdcard/swapfile.swp to /system/sd/swap.swp
Here is the reason why. The default location is your FAT32 partition. If you all of a sudden mount your phone to the computer with the swap file running on FAT32 you will corrupt your sd card, and then you will have to wipe and reinstall everything.
If you set the location of your swap file on /system/sd/ that's actually your ext2/3 partition and never gets mounted and you never have to turn swapper off.
Well I hope this helps some of you out. I will be writing the walk through on loading up live distro of Linux and partitioning your card sometime today.
I have used this method on a couple different phones and it has worked each time. Also I really recommend installing cyanogens recovery 1.2, as its an excellent way of making a back up of your phone and doing future flashing.
If there is anything anyone thinks that could be done better feel free to post in here.
Remember different people have different ways. I have posted this way cause it has worked for me on my phone and two other phones I setup, and each time there was no hicups.
FILES:
Radio 2_22_19_26I
NEW SPL
CM-Recovery-1.2
Ubuntu Linux Download
DISCLAIMER:
I am not responsible for anything that you might have done to your phone by following these directions. Like I mentioned before so far every time I have used this method, I have had nothing but success.
While I can appreciate this topic, I think you need to speak with less certainty that this will always work properly the first time.
For example - I'm coming from the Ramjet ROM, and the process that I have taken.
Freshly formatted 4gb sd card with a 700mb EXT3 partition, the rest is fat32.
Loaded JACHero 2.3 and renamed update.zip
Wiped twice
Installed ROM
Phone went into boot loop - allowed to run for 10 minutes
Removed battery
Attempted to install ROM a second time
Boot loop again - allowed to run 10 minutes
Wiped again
Installed ROM
Boot loop again - allowed to run 10 minutes
It seems strange, as going from a standard JAC build previously I was able to just wipe, wipe, install and had JACHero 2.1 working without a hitch. I found this strange, as people were complaining about that build, but it seems 2.3 is what's giving me the most headache.
/shrug. Guess I'll go back to Ramjet.
Great post, dude. I've rooted my phone, flashed a few ROMs, including Haykuro's Hero, moved Rosie back to run on the phone instead of the SD card, overclocked and run Swapper. I was still a bit confused and hesitant to flash the JAChero ROM. I'm feeling better about it now. Gonna flash when I get home from work today.
TooSlo said:
While I can appreciate this topic, I think you need to speak with less certainty that this will always work properly the first time.
For example - I'm coming from the Ramjet ROM, and the process that I have taken.
Freshly formatted 4gb sd card with a 700mb EXT3 partition, the rest is fat32.
Loaded JACHero 2.3 and renamed update.zip
Wiped twice
Installed ROM
Phone went into boot loop - allowed to run for 10 minutes
Removed battery
Attempted to install ROM a second time
Boot loop again - allowed to run 10 minutes
Wiped again
Installed ROM
Boot loop again - allowed to run 10 minutes
It seems strange, as going from a standard JAC build previously I was able to just wipe, wipe, install and had JACHero 2.1 working without a hitch. I found this strange, as people were complaining about that build, but it seems 2.3 is what's giving me the most headache.
/shrug. Guess I'll go back to Ramjet.
Click to expand...
Click to collapse
I can completely see what you mean by that. But only reason I decided to make this, because two other phones that were having the exact same problems, started working after I did this.
They both had the same symptoms everyone else, and no one really knows where it came from.
So I made sure they had the right radio, then the right SPL, and every time I did something to the SD Card I killed the partitions completely not just format them.
But I destroyed the partition, recreated it and then formatted it to a file system of my choosing.
my g1 is fine ive flashed every rom here and never gotten stuck on boot loop, if anything the files youre downloading for recovery and spl must be corrupted try re downloading your radio file and spl's again.
Include Disclaimer
I like your post but here is something that I would add to your post.
Even though this has worked every time for you do not assume that it will work for every one, therefore make sure you put a disclaimer out there. As you may have seen before, there have been a lot of posters that have blamed others when their phones were either bricked or stuck in boot loops.
Remember....some people may do something wrong during a step and swear that they followed it perfectly and then blame you.
A detailed disclaimer could be of some help since a lot of people will be taking your post as LAW......
for somereason im not able to update my spl is it something u must do i keep gettin a veification faild message when im tryin to flash it wiht alt + s and i cant seem to update to jachero 2.3 im using a 1 g micro sd im really not sure whats going on i have the proper raido settings and everything. also im not really sure how to create 2 partitions on my memory card im running good ol windows vista
how fast is this running.
i tried it once without swapper and it was way to slow in my eyes in order to use at as an everyday phone.
hope you have something for me (is swapper this perfect solution?)
In my opinion the perfect solution is making a a linux swap partition on your sd card.
However last time I created a linux swap partition and created my swap file there after I rebooted my phone I got stuck at the G1 screen.
I think this might have been cause because of having three partitions on the card but I am not 100% sure.
So instead I just use swapper and make it mount the swap file on my ext3 partition which seems to make this rom run really freaking smooth.
Also I have noticed significant improvements of using ext3 vs ext2, but when research how the two different file systems work it makes sense why it would make a difference.
So to answer your question, is swapper the perfect solution? Im not sure if there is anyone perfect solution but I do know that this sure ass hell makes a huge difference in how your Hero rom runs.
for those having boot loops, how about help us help you, run ddms from sdktools and grab a log of whats going on, this way we can determine an issue, because those asking for help with bootloops and asking for help is like asking me to tell you whats wrong with your car over the phone. we cant tell if we cant see whats going on. so helps us, if you have adb and not the sdktools just type
Code:
adb logcat
this way we can see what your phones trying to do.
Excellent post! I wish I this was available yesterday when I did my first Hero ROM ever. The JAC thread is huugggeeee.
Not to hijack your post, but I'll add my two cents and experiences from yesterday if you do not mind.
-------------
Ok first time on Hero. Coming from DudesCupcake.
Pre
Formatted 1gb SD card 500mb Fat32, and the rest Ext3
hxxp://allshadow.com/forum/viewtopic.php?f=9&t=5870
1. Flashed Radio 2.22.19.26I from (update.zip) successful (camera+power to check)
hxxp://code.google.com/p/sapphire-port-dream/
2. Flashed SPL 1.33.2005 from (renamed update.zip) successful (new three android skateboard logo on bottom)
hxxp://code.google.com/p/sapphire-port-dream/
3. Updated to JACHero r2.2.1 from Page 1
Now I have a boot loop, Hero -> HTC...
After installed 2.2.1 should I pop my SD card out and format it again on my computer?
Trying to do the 2.2.1 again.... Wish me luck!
**Update**
Updating to the 2.2.1 again worked.
Ok, everything works!! Much thanks to Luckenbach for the moral support, and thanks to JAC and all the other guides that I linked in my process. So if anyone else is a noob like me you can do exactly what I did (I provided links for each step where I got it from) you should be ok.
XDA rules!
------
Quick questions for people with loop problems.
is your linux partition ext2 or ext3?
southeastbeast said:
Excellent post! I wish I this was available yesterday when I did my first Hero ROM ever. The JAC thread is huugggeeee.
Not to hijack your post, but I'll add my two cents and experiences from yesterday if you do not mind.
-------------
Ok first time on Hero. Coming from DudesCupcake.
Pre
Formatted 1gb SD card 500mb Fat32, and the rest Ext3
hxxp://allshadow.com/forum/viewtopic.php?f=9&t=5870
1. Flashed Radio 2.22.19.26I from (update.zip) successful (camera+power to check)
hxxp://code.google.com/p/sapphire-port-dream/
2. Flashed SPL 1.33.2005 from (renamed update.zip) successful (new three android skateboard logo on bottom)
hxxp://code.google.com/p/sapphire-port-dream/
3. Updated to JACHero r2.2.1 from Page 1
Now I have a boot loop, Hero -> HTC...
After installed 2.2.1 should I pop my SD card out and format it again on my computer?
Trying to do the 2.2.1 again.... Wish me luck!
**Update**
Updating to the 2.2.1 again worked.
Ok, everything works!! Much thanks to Luckenbach for the moral support, and thanks to JAC and all the other guides that I linked in my process. So if anyone else is a noob like me you can do exactly what I did (I provided links for each step where I got it from) you should be ok.
XDA rules!
------
Click to expand...
Click to collapse
When you do the CAMERA+POWER boot, what exactly does the second line from the top say?
lol I wasn't requesting help, I was adding to your post! To hopefully help other people =)
Oh I know I'm just collecting data right now that's it.
DREAM PVT 32B ENG S-OFF
HBOOT-1.33.2005 (DREA10000)
CLPD-4
RADIO-2.22.19.26I
Apr 20 2009,15:30:43
--
Edit: Also changing location of swapper from your info helped a lot! Thanks, I had the SD problem when I pulled out my SD card to put photos back on (instead of using adb) and I got stuck in a boot loop, I thought I was done for. Just rebooted it a few times and it was back up and running. Good tips =D
what do you mean by "new buttons"?
A quick question that ill ask here as to not clutter up JADs thread any more than it alreadsy is.
I have put on 3 of his roms in the last few days and where as they are stable they are dead slow at times for me. I am using a 2g class 2 sd card with an ext3 partition. How much more would a class 6 card speed swapper up? Is one worth getting?
Sorry to post up in this thread again, but I just wanted to provide some more of my experiences here.
I'd picked up Paragon Partition Manager and used that to format my SD card and create the ext3 partition on it as well. It seems something is wonky with how it created it, as every time I've created the partition, even with different sizes, I always get stuck in a boot loop when trying to install JACHero even though any other ROMs will install just fine.
I've put the update.zip onto my older 1gb card that came with my phone just to see if it would install, and though it took a while, it installed without any issues.
After going through the setup process, I attempted to put in my 4gb card with ext3 on it. Lo and behold, boot loop.
Seems something is funky with the way that Paragon Partition Manager creates an ext3 partition.
I'm now going to install an older ROM and go through the "creating an ext2 partition through the G1" method and then attempt to convert it to an ext3 through Cyan's instructions.
I'll try to keep up to date what's going on. I know this place isn't a blog, I'm just hoping someone will point out my idiocy if I'm making any huge mistakes somewhere.
TooSlo said:
While I can appreciate this topic, I think you need to speak with less certainty that this will always work properly the first time.
For example - I'm coming from the Ramjet ROM, and the process that I have taken.
Freshly formatted 4gb sd card with a 700mb EXT3 partition, the rest is fat32.
Loaded JACHero 2.3 and renamed update.zip
Wiped twice
Installed ROM
Phone went into boot loop - allowed to run for 10 minutes
Removed battery
Attempted to install ROM a second time
Boot loop again - allowed to run 10 minutes
Wiped again
Installed ROM
Boot loop again - allowed to run 10 minutes
It seems strange, as going from a standard JAC build previously I was able to just wipe, wipe, install and had JACHero 2.1 working without a hitch. I found this strange, as people were complaining about that build, but it seems 2.3 is what's giving me the most headache.
/shrug. Guess I'll go back to Ramjet.
Click to expand...
Click to collapse
did you try going into recovery and then choosing fix file extensions... that happend to me, it might be because you have no ext 2
Related
Hey guys,
yesterday i flashed my g1 with JF RC33 and alls fine, except by one thing: every time i turned it on, a message pop up telling that android.process.media needed to be close.
Then I did a wipe, but after this i can't turn on my phone again, it stay on the flashing android screen
What should i do?
Thanks!
it seems to be caused by a broken system file or hardware problem. could you try flashing your system again? this update.zip is signed, so something must happened during the copying process.
Simply reflash an update. I recommend you do a Nandroid backup next time. Also, make sure your SD card is in your phone when turning on. For some odd reasons, when my SD card isn't in my phone, it just hangs on the boot image. Very strange. I have Apps to SD and am running on Haykuro 5.0.2H
it looks to be an issue with your sd card, do you have apps to SD enabled or anything else with your phone that might need to access the SD card at boot? if you have apps tp SD then you need to re-push the mountd.conf and the init.rc and redo the links to your /system/sd partition. if not i would make sure that your SD card is not corrupt by formatting it again. as solomenwishing(sp) said next time you should make a nandroid backup of your phone before you mess with anything
Thanks guy.
I flash everything again and it's ok.
Now i don't know how to make the nandroid backup.
Can someone help me?
Search is your best friend here....
http://forum.xda-developers.com/showthread.php?t=459830
Well this is a sticky on this forum
okay, i had already read this before, but the only thing that i don't know for sure is this.
"Android G1 phone in recovery mode with busybox installed, including appropriate symlinks to at least tar and md5sum, as well as 'adb shell' support running as root."
My recovery image is from the JF topic "How -to- Root,Hack and flashing...."..the only thing i know is my one has the adbshell support running as root
It's ok to do this?
TKS GUYS
I have the 0.7 rom load with both patchs and the blue theme, I want to try out apps 2 SD i just didnt know the best route in doing so, for it to work correctly with your rom. If i use the format function in the recovery menue would it automatically save my apps on the SD and work properly or would i have to reinstall them?
BAttitude7689 said:
I have the 0.7 rom load with both patchs and the blue theme, I want to try out apps 2 SD i just didnt know the best route in doing so, for it to work correctly with your rom. If i use the format function in the recovery menue would it automatically save my apps on the SD and work properly or would i have to reinstall them?
Click to expand...
Click to collapse
(I personally don't like apps2sd but if you really have that many apps...)
Yea. Backup your sd card (it will get wiped). Boot in to recovery and create swap+ext2+fat32 and then convert ext2 to ext3 (all are options in the recovery menu). It will move everything for you.
Why don't you like apps 2 sd? I just figure if you have that you won't have worry about internal memory if you wanted to have a lot o
PHP:
f apps
This is why he doesn't like it:
flipzmode said:
**My note about Apps2SD: I added support for it in this release of the rom because people who were using it in other roms that tried to install this rom were receiving errors. Here's my point of view on it.
I played with it for over 8 hours today between implementing it and then testing it to make sure this fix would work. I have personally come to not like apps2sd, but I am including it for those who use it.
The reason I don't like it is because it puts your phone at a huge risk of having problems once anything goes wrong. If you install a program that causes issues, a nandroid backup will not resolve the issue because the application is installed on your SD card not your phone. If your phone starts going crazy as reported here and here, then even just a restore possibly won't fix it. You might need to go as far as to wipe your SD card too. If you are lucky enough to have a restore fix your problems you will still need to reinstall every app, even if you didn't wipe your card. And on top of that when you try to reinstall any app it will think it's still installed, even though you restored your phone. But when you click "uninstall" it will just freeze half the time because there's nothing on the phone for it to actually install. I have also read many threads that say if you happen to boot the phone up without the SD card in then it will screw everything up.
So now maybe you are wondering why I would add Apps2SD support in this rom. In order for people who are currently using Apps2SD to upgrade to this rom I must support it or require them to do a hard reset before coming to fresh. Clearly I don't want you to have to reset so I have supported it. With that said: I personally recommend not using it. This rom will auto-use it if your SD card is formatted for it (fat32+ext2+swap partitions) but it won't use it if you are only partitioned as 1 fat32. My suggestion is to stick to the 1 partition and let your applications install on the phone. Linux is not like Windows in the sense that it will run the same whether you phone has 140 megs free of storage space or 10 megs free. So unless you plan on installing 100 apps, I don't see the practical purposes of using Apps2SD. But a lot of people like it.
Now with all of THAT said -- this rom officially has and supports Apps2SD. It is a program that I think has the possibility of being great, but has to work within the confines of the phone which means tricking Android in to thinking that the applications are installed on the phone when they aren't. That is what leads to all the problems mentioned above.
Click to expand...
Click to collapse
If i have apps2sd already from the previous rom i don't have to re-do it for the new one correct?
no you dont.
using apps2sd2 problems
I followed all the instructions here http://forum.xda-developers.com/showthread.php?p=5618439#post5618439 for apps2sd2 yet when I open the app, it STILL says Oops, you have to run through the tutorial to set it up. I've DONE THIS. I'm extermely frustrated. I have no idea what more to do. My sd card is partitioned correctly. I've run all the commands listed in that tutorial. PLS HELP! Also all my apps are showing in /system/sd/app AND data/app. Is this correct? Why won't Apps2sd2 work for me? I really need some troubleshooting help.
I have a rooted CMDA HTC Hero using the Fresh ROM. Also is there a way to still get Sprint TV using this ROM?
Fresh .7 doesn't support A2SD, only Fresh 1.0 & 1.1.
I've been crawling forums looking for several ways to partition my SD, but to no avail.
Recently upgraded from damagecontrol 2.08 to 2.09. Bought a new 8gb micro SD.
I'd like to partition the SD card so that Apps2SD runs, and I remember the first time I rooted my phone and loaded a rom, there was an option in recovery to partition the SD card. Now, my phone boots into clockworkmod recovery v1.8.1.4, and the list of commands doesn't include a card partition option.
How can I get this option back?
I resorted to using adb and trying to work around this problem through the command line, but all of those attempts failed. "parted not found" etc.
I'm at my wit's end and my school work is suffering! (I'm crazy if my phone is not working perfectly) PLZ help this girl stay in med school!
Try this thread and let me know if that's what you're trying to do.
Actually I found that post after the fact that I set my hero back to factory settings in desperation.
What I did with my rooted and fully functioning hero was...
back up apps
changed SD cards
set to factory settings via an option of the clockwork recovery
updated my rom to damagecontrol 2.09
found that apps2sd wouldn't work
tried to get back SU capabilities unsuccessfully
tried to mimic my first root and flash attempt unsucessfully with flashrec
Now I'm stuck with a slowed down hero which can't allow Su and won't do apps2SD
I'm at the point of insanity with this thing
any sugestions?
Hi all,
Yes, I'm a newb here at xda, but not to the hacking scene. As my interests are in custom Firmware development/modification I am having to post here in General because of the 10 post limit for the Development forum portion. I hope that I may get a response here, but worried that as with most "newbie chat" type forums, they seem to get ignored.
Regardless, I have been trying to install the CM9 and CM10 to my MK802 PC thumbstick without any luck. The end result is either a bootloop with no video or a blank screen with no video output altogether.
I have been using instructions from here, but there seems to be a simple step that I am missing.
All requirements for Superuser, busybox, and smanager have been fulfilled, I am able to install CWM to do my factory resets and flashing, but I am not successful in the flashing. I'm not sure if I need to resize my system partitions, but that is something I've a feeling may affect the install. I've not seen any statements on the requirement, only that if the system partition is less than 350MB or so, to avoid flashing the gapps file, which I've followed.
I've attempted this on the FW710B, and the NEW03 image from the Rikomagic website as well.
If anyone has any ideas or can point me in the right direction to an already customized image I can flash with Livesuit, I'd appreciate it.
Thanks again,
T3ch42
optimal swap and / partition sizes??
Well, a little bit of an update. I took the plunge and repartitioned my internal SD memory. I chose 512MB for the system, and 64MB for the swap. That may have been not enough for the swap, but this was a new test.
This particular iteration was successful. I got the CyanogenMod boot screen and everything this time. The boot took a little while, hopefully just the initial boot.
It seems that this would be a pretty big step to take, but I really can't say that I saw mention of resizing the internal memory as being required.
If anyone has suggestions as to the optimal swap and system sizes, I would appreciate it.
Thanks
t3ch42 said:
Well, a little bit of an update. I took the plunge and repartitioned my internal SD memory. I chose 512MB for the system, and 64MB for the swap. That may have been not enough for the swap, but this was a new test.
This particular iteration was successful. I got the CyanogenMod boot screen and everything this time. The boot took a little while, hopefully just the initial boot.
It seems that this would be a pretty big step to take, but I really can't say that I saw mention of resizing the internal memory as being required.
If anyone has suggestions as to the optimal swap and system sizes, I would appreciate it.
Thanks
Click to expand...
Click to collapse
Good to know, I have the same problem as you. How did you repartition the internal SD memory? thanks
woonaval said:
Good to know, I have the same problem as you. How did you repartition the internal SD memory? thanks
Click to expand...
Click to collapse
I believe that I used the partition tool through the recovery app that you install, but I'm beginning to wonder. CT says that you cannot resize it. I have installed the Uberoid image a few times, and that may have resized it for me in all actuality. I did notice that when I had a SD card in the machine, that the SD card was resized instead of the internal memory which threw a kink in the works. After CM9 was installed, I wasn't able to use the internal memory.
Still doing some tests though.
May have more info in a little bit.
What steps did you take to get CWM on the stick. I tried several all not giving me a screen on reboot.
nyarnon said:
What steps did you take to get CWM on the stick. I tried several all not giving me a screen on reboot.
Click to expand...
Click to collapse
Install the Uberoid img through live suit and format.
After it boots, check your internal storage. It should say about 1.69GB
install the recovery, and boot to it.
Do a factory reset in recovery as usual, and then install your cm9 or cm10 images(the zips).
Install the gapps and compatability zips and reboot.
That should be it.
I think that's the steps I took that were successful.
If I tried to partition it myself, I found that the internal sd would not be recognized, even after trying the format memory zip that is used to fix th ad card.
Hope that helps.
I may have not looked closely enough.
You're having trouble with the cwm install?
For that, I just installed su, updated that to the newest version, click on the i and let it check the installed version.
Install busybox and the script installer. Use the cwm 4.0.4, I believe it is, and install the recovery image to the mk802.
The recovery.img needs to be in the main memory to run the script. Once you've run both of the scripts as root by clicking the little button in the script installer, then the mk802 should boot into recovery.
If this is what you meant, then hope this clears it up.
I am asking this again here, as my previous thread seemed to be hijacked by someone elses question!
I recently decided to root my inspire as i am no longer using it as a phone, so i thought that it would be interesting to do and fun to play around with all of the options available (i recently did the same thing on my Nook Tablet, and that was the single best decision i have made a while!). I started out researching the manual techniques to do it, but i didn't really like the high risk factor there (i really dont want to brick my phone) so i tried Ace Hack Kit. Of course, it has to download the phone from 2.3.5 to be able to work. During this process, it has me hold volume up and power twice, and every time i do that, it flashes up really quick something about holding volume up and volume down and power, but then it skips past that. Anyway, here is where my problem comes in: It says that it should reboot in to hboot, which it does, but that hboot should run a test, then prompt me to continue by pressing volume up, and then should reboot, flashing twice, and that should be the end of it. THe problem is, it does boot in to hboot, but it is just a standard hboot screen asking to recover, load bootloader, etc. When i reboot from there it just boots in to the phone as normal. I have tried 3 different SD cards, all of which work and are recognized by my PC, my other phone and my Nook tablet. I have also inserted a working sim card, just to be sure that wasnt the issue, and i still cant make it work. Does anyone have any experience with his issue, or any idea what i might be doing wrong?
Opening multiple threads on the same issue is frowned upon. Even if someone supposedly hijacked your thread. I read it and only 7 posts ,I'd call that far from hijacked.
Now at the issue on hand. As mentioned in the other thread. Its the SD card. Also their is a hack kit irc go there. Plus pasting the output would help aswell
marsdta said:
Opening multiple threads on the same issue is frowned upon. Even if someone supposedly hijacked your thread. I read it and only 7 posts ,I'd call that far from hijacked.
Now at the issue on hand. As mentioned in the other thread. Its the SD card. Also their is a hack kit irc go there. Plus pasting the output would help aswell
Click to expand...
Click to collapse
OK, as i have stated, i have tried a new SD card (2, actually, with the same results.) as far as an output screen, there is none. Ace Hack Kit goes through the whole downgrade process, my phone gets in to hboot, but it is just a standard hboot screen, and it doesn't downgrade. When my phone restarts, it restarts like i just did a factory reset.
There is an output,copy what ever it says. There probably is something you missed
As too the SD card ,try adifferent one again. Your SD cards are corrupt and you need to find one that works with the kit
Also since your on a sense 3.0 did you do the changing of the boot img before running the kit?
marsdta said:
There is an output,copy what ever it says. There probably is something you missed
As too the SD card ,try adifferent one again. Your SD cards are corrupt and you need to find one that works with the kit
Also since your on a sense 3.0 did you do the changing of the boot img before running the kit?
Click to expand...
Click to collapse
by changing the of the boot img do you mean downgrading it? That is what i am trying to do. The kit is supposed to do it automatically. If that is not what you mean, please explain!
As to the output, copy thing, no, there is none of that. I have followed the instructions about 20 times. After starting the downgrade process, the phone restarts and comes up with a red triangle. At that point i am supposed to hold volume up and power, and it goes and reboots and i do the same thing again. At this point, i am told that the phone will boot into hboot and check the boot image. When it is done, i am supposed to hit volume up to confirm, and then the phone will reboot, this time in to the down graded image. That is where my problem comes in. Instead of checking the boot image, it just goes to a standard hboot screen. There are no error messages or warnings, and i have followed the instructions to the letter.
As far as the cards are concerned, the maker of the kit suggested a 2 or 4gb Sandisk series 4 or 6 SDHC card, so i bought 2 of the series 6 4gb, along with the 2 others that i already have. I also have 2 series 4 4gb and 2 series 4 2gb Sandisk cards, as well as an 8gb and 2 4gb PNY cards. All of the cards recognize in my phone and PC, and the older cards also recognize in my Nook (and were used to root and load custom roms on several other devices), i have not loaded the new cards in to any other devices besides my laptop and the phone for fear of corrupting it. So i find it difficult to believe that the cards could be the problem.
I know what the kit says. What I'm saying is In the command prompt it spits out a lot of info. For example it will say stuff about zergrush and or taco root. THATS the important stuff, this is what is used to allow the downgrade to be possible. If their a failure in the process it would state it there. That's why I keep asking for it. Don't understand your reluctance to do a simple copy and paste
The changing of the boot img is something that is different and you should read about it on attn1 site. Version 3.20 has a slightly different method
marsdta said:
I know what the kit says. What I'm saying is In the command prompt it spits out a lot of info. For example it will say stuff about zergrush and or taco root. THATS the important stuff, this is what is used to allow the downgrade to be possible. If their a failure in the process it would state it there. That's why I keep asking for it. Don't understand your reluctance to do a simple copy and paste
The changing of the boot img is something that is different and you should read about it on attn1 site. Version 3.20 has a slightly different method
Click to expand...
Click to collapse
I appreciate the attempt to help (the reason why i didn't post a direct copy paste was simply as i was in no position at the time to take one, not any reluctance to ultimately do so...) In my recent attempt to provide you with a full copy paste of the process, i was able to figure out what i was doing wrong. For anyone who may have the same or similar issue: format the SD card while it is in the phone from your PC right before starting the process. Thats all it took. Even for a card that was brand new and untouched, or formatted before putting it in the phone, i couldn't get it to work, but it worked doing it that way, and i am now happily rooted and ready to install CM9!
Glad you got it figured out. Formatting the SD card in the phone is a must, since the phone puts important files on the card after formatting.
pazzo02 said:
Glad you got it figured out. Formatting the SD card in the phone is a must, since the phone puts important files on the card after formatting.
Click to expand...
Click to collapse
Wrong. There's no need to format the sdcard to run the Hack Kit, unless your sdcard is not in fat32 system file format. The only requirement is that your sdcard must not be corrupted to work as a goldcard. Corruption of the boot partition of the sdcard can not be solved by formatting and is produced by improper dismount of it.
glevitan said:
Wrong. There's no need to format the sdcard to run the Hack Kit, unless your sdcard is not in fat32 system file format. The only requirement is that your sdcard must not be corrupted to work as a goldcard. Corruption of the boot partition of the sdcard can not be solved by formatting and is produced by improper dismount of it.
Click to expand...
Click to collapse
I'm just speaking from experience. Every SD card I've put in my phone I had to format in the phone because it was giving me problems. After, no problems. Maybe it's just my phone. or the cards weren't FAT32.
You're last sentence is probably where most people screw it up. You can't just yank an SD card out of whatever device it's in, which I think a lot of people do. But I have fixed cards that were removed without unmounting by formatting. Maybe other parts were corrupt but not the boot partition?
pazzo02 said:
I'm just speaking from experience. Every SD card I've put in my phone I had to format in the phone because it was giving me problems. After, no problems. Maybe it's just my phone. or the cards weren't FAT32.
You're last sentence is probably where most people screw it up. You can't just yank an SD card out of whatever device it's in, which I think a lot of people do. But I have fixed cards that were removed without unmounting by formatting. Maybe other parts were corrupt but not the boot partition?
Click to expand...
Click to collapse
As far as I am concerned the boot partition can not be restored by formatting. SDCARD should always be dismounted properly.