Related
Hi,
I have tryed to upgrade my rom to a new version (Prophet WM5 AKU3.2 v3231). Followed the stept correctly, however my phone does not boot anymore. It gets stuck in the qtek logo (when it displays the AKU version i´ve got) and the sceen gets all shacky.
An addictional problem is because it is stuck at that point it does not connect to my computer....
What can I do to fix this, any good suggestions
Thank,
Sebastiaan
You should be able to enter bootloader mode by pressing and holding the camera button while you power on your phone. On the bottom left, you should then see "USB" - connect it to the PC and flash it again.
Had to do this yesterday after flashing failed.
Mike
thanks it worked
Sebastiaan
Error [296] Upgrade Only
Hello
I have same Trouble & I Make Bootloder from USB but Always I get This Error
ERROR [296] UPGRADE ONLY
This NBF file connects used for your PDA Phone. Please get newer NBF file.
Note: I try to Upgrade to 2006-11-12_Prophet_WM5AKU2.3_lvsw_edition but my Phone Stack So I reset as say after 30 m
Now I trying to back to Old Software from I-mate
Also I try to upgrade to 2006-11-12_Prophet_WM5AKU2.3_lvsw_edition but no Connection....
Please help me I with out Live (Phone)
I know it sounds strange but i used a different USB port and then it did connect. Now that everything is back to normal i can use the old one again.
maybe it works for you as well
I tried doing that, but for some reason my computer doen't recognize the device...pls help!
Can someone upload an old ROM for the prophet? I can't start up my prophet, but I've got it in bootloader. So I nedd a little bit old ROM so I can install on it.
Understand?
Thanks!
Look for the first link here http://forum.xda-developers.com/showpost.php?p=1166927&postcount=2
Are this ROM old ROM?
Not really old but if your phone stuck in bootloader this one is ok
I can't make it, it says that i should connect to Active Sync, and how im I suppose to do that?
Go in bootloader (screen with 3 coulours) by Hold down the camera button and reset the device. (Boot Loader Mode is: Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.)
When you are in bootloader logicaly your PC must detect the Prophet, then run the update
Sorry for my bad English but I'm Franch
Yes i've got it in bootloader, and its stands USB on the PPC screen. But it aint the Active Sync that finds it, it says "Uknoknown Unit" or something when i connect them together..
Active Sync isn't a problem, update work or there is an error message?
In right corner down on the PC sreen it comes up "A unkknown Device connected" or something like that, nothing more is happening..??
It sayd that it can't recognize the unit..
Qtek_S200 said:
It sayd that it can't recognize the unit..
Click to expand...
Click to collapse
In bootloader mode, on connecting via usb ,if u r getting 'USB' written on left down corner of ppc then ur ppc can be flashed via proper RUU and nk.nbf
Be sure that this nk.nbf dont include ipl/spl parts for risk free flashing and for not getting brick device.
thanx
nandlal
Im trying to flash a ROM with that, but it coming up on the screen that "Not connected". It's standing that i nedd to connect with Active SYnc!!
could somebody upload an ipl/spl lower than 2.09 or higher but not 2.09^^
rest doesn't matter language english or german would be good...
Hello there,
I tried to flas my MDA and now it stays in bootloader (1.01). Whatever I do: it stays there! (hard/factory reset and what not). Whenever I want to install a new rom by a RUU application, this goes wrong as well!Any help would be much appreciated!
Ive the same problem @ the moment! I tried to do a Rom update and then an error appeared and the installation failed and the recovery afterwards aswell! Now my Universal stucks in the bootloader mode showing USB v. 1.01! How can I get out of this mode! I tried the hard reset, like joenie described but i didnt work!
Aalsen said:
Ive the same problem @ the moment! I tried to do a Rom update and then an error appeared and the installation failed and the recovery afterwards aswell! Now my Universal stucks in the bootloader mode showing USB v. 1.01! How can I get out of this mode! I tried the hard reset, like joenie described but i didnt work!
Click to expand...
Click to collapse
I have the same problem sometimes when I change ROM version, the installer reboots the PDA in USB mode and nothing, the installer display an error and crash. The PDA in not recognized correctly in USB mode.
It is due to your PC (Activesync crashes in silent mode and disable WM device drivers) and not the UNI!!!
Try restart activesync (open it), unplug and replug the UNI and restart installer, the installer will not recognize the actual ROM version but it should be working...
If it fails try to restart the PC or uninstall and reinstall activesync and retry installation...
Be carrefull because in USB boot mode the UNI cannot charge the battery, if the battery is down, you cannot restart installation (And cannot disable boot mode).
I was affraid the first time of USB boot lock (It was the panic, UNI bricked...) but now, I know the problem and I resolve it fastly (restart activesync).
Good luck!!!
Hey thanks for all the advices! i found a really good tutorial how to unbootloader it. But the actuall problem is that windows vista is not having any active sync like Windows XP. I now you can download a windows mobile device manager and I tried the deactivation of the USB port over this one, but it didnt work! Is there any other methode oder way how to get access to the phone to change the status?
Thank You very much!
Aalsen
Aalsen said:
Hey thanks for all the advices! i found a really good tutorial how to unbootloader it. But the actuall problem is that windows vista is not having any active sync like Windows XP. I now you can download a windows mobile device manager and I tried the deactivation of the USB port over this one, but it didnt work! Is there any other methode oder way how to get access to the phone to change the status?
Thank You very much!
Aalsen
Click to expand...
Click to collapse
Can you add here the link of the tutorial???
May be try remove usb devices in the device manager of Vista and reboot the PC to redetect the UNI USB drivers.
well lad's and gent's..
I found out what my real problem was
It was a broken USB-cable :|.. wtf!!!
Well anyway. I think you guys are great! all the posts/helps!!
It some else to do???
I try to flash my JASJAR and I brick it........The instaler send my an error and I stuck in bootloader but the instaler window says to cool reset the Universal and the Bootloader was gone and the universal now is death, can't turn on and no Boot...Its bricked and I still crying!!!!.....
Well I have installed a new Rom yesterday on my Q9000...
I whas using my laptop which has Vista on it. Dont know what happend but I got an error msg on my laptop...Tried to reboot my Qtek but it whas hanging on the bootup screen(the 1st screen which shows all Rom/ext rom and Radio version). No matter what I did it refused to bootup...
When plugging in my Qtek on to my laptop, the bootloader screen changed from serial to Usb...
Finally I tried it on the desktop wich still runs on XP and it did the Romupgrade without any pain...
I did several Romupgrades on my Herald all on my Vista laptop without any problems...I don't really understand what or why, maybe because the Qtek is older than the P4350 that it is less compatible with Vista?
Bottom line, I now have a Qtek 9000 which is fast ...
Hello XDA Nice Team !
By mistaken i wrote some file to my bootloader in my I-Mate Jam ..
That was after using the bad ROM : 2.03
it's the worst cooked version i saw !
Now my bootloader mode is working .. but no way to connect to PC with USB port ..
My computer does not recognize my Magican when plugged in bootloader mode anymore!
Bootloader Ver: 1.0
is there any way to fix or upgrade or restore original bootloader
Now i cant upgrade or downgrade my magican by any method
Noway to use successful connection with any roomupdate utility
Please help me to fix or restore my bootloader!
Thanks to any one read or replay or try to help or help me to resolve my problem
XDA lover
i'm sorry that happened mate...
i've had success with flash-from-bootloader attempts before, both on my Magician, when i accidentally flashed off of Vista and it'd enter the bootloader every week or on a reset using the reset hole, and also on my Wizard when i ignored warnings from WM5torage and it'd only enter the bootloader
what precisely happens when you connect to the PC, allow USB connections in AS/MDC, and let the phone enter bootloader however it does? i can just flash a rom from there, but i won't (iirc) get any reports of as recognising the device...
My experience:
1- when i plug my sd card into my jam .. usb not recognized in bootloader mood !!
2- when i use puty or roomupdate it reaches to USB> then when i type any command it does not respond !
3- i could do something .. i let my phone bootup and this i-mate logon screen stays 4ever .. i connected my ppc to pc and i could explre my imate by activesync ...
i could reach something .. when i explore my phone and remove everything from startup folder .. my phone boots .. and i can see start botton .. no touch alignment comes .. and everything works .. but.. screen is virtually reversed .. i can see the OK botton but i must click on the facing area and it be clicked ..
i think i executed some wrong hard SPL to my phone ant that happened >
is there any way to resolve this problem?
is there any way to erase flash on my I-Mate Jam????
is there any way flash my phone?
i also have prepaid JAFWM with pkey and USB cable .. no BOX ..
Help please!
that's messed up... howsabout flashing it at the point when the phone boots up? if there's an AS connection there, then it may work... i'd flash to an official rom though
Same problem , PLS Help !!!
Thx for help
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
If your magician isn't detected at ALL by your PC when plugging the USB cable into it (i mean, no new hardware; no unrecognized hardware; nothing is detected in your PC when you plug the USB cable), and unless you had previously made a SD backup of your entire Flash with this procedure ( http://wiki.xda-developers.com/index.php?pagename=MagicianSDflash ), then your only option will be to build a JTAG diag cable:
Here are some general directions / ideias:
Magician JTAG pinout: http://wiki.xda-developers.com/index.php?pagename=MagicianJTAG
How to build/run the JTAG: http://wiki.xda-developers.com/index.php?pagename=DeadBoot
Photos : http://www.cf-box.com/htm_data/55/0912/1679.html
Some interesting stuff for debugging problems: http://pda2u.ru/ptopic205.html
For sure cotulla has one built so to test his ROMs + bootloader - maybe he will be willing to give you some directions if you run into problems, and above all, give you a prepared .nb0 (with the bootloader file) for your magician, which i do not know if there's one out there, extracted from an original ROM.
Anyway, you can always try and do it for yourself using itsme utilities. Follow this link: http://forum.xda-developers.com/showthread.php?t=218643
Regards
Keeper,you're awesome! I'm searching for JTAG,too
xiaojin1985 said:
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
Click to expand...
Click to collapse
Dear xiaojin1985 ,
Thx for your help, But unfortunately i tried your solution but it dosnt work !
Dear Keeper,
Thanks too for your help,
and i think the solution for my problem is one of the solutions you says ( How to build/run the JTAG: ) ,
but the pictures is not available anymore , so pls can you get the pictures ?
All the pictures are in here:
http://s218.photobucket.com/albums/cc23/alex_beda/ and in attachment there's a .mth file with all the pics built-in.
Don't take it wrong what i'm about to say, but in all honesty if you can't figure this out yourself (digging up the internet for the missing pics), i would suggest that you shouldn't try this, since this ain't easy at ALL...
Just to give you some ideias, it will require you to adapt your magician test point signals (TDO;TDI; nRESET; etc,)seen on the magician pinout pic to what is said; solder very thin wires (best done with a small hot air tip); fixate the small dip switch (micro switch) to be always on; keep the USB connected...idk... plus alot of other small details which ain't easy to accomplish.
Personally i haven't tried this yet but for sure it would work
If you decide to go ahead, please post some results!
Connection error solution
this is my problem
hi all. A friend of mine gave me an S100, and after i played for a few days with it, i decided to update it's rom. A "country error" problem appeared,cause i have the greek version, so i ran MaUpgradeUt_noID.exe which completed (as showed 100% process). My (new) problem is that i cannot update anymore. Every time i enter boot menu, i ran the upgrade
(HTCMAG_ROM_WWE_O2.rar) following all the steps normally. When the device resets (so the upgrade is going to start), it's re-reseting again and showing ERROR 101 connection error. Any ideas?
Qtek Greek version
R 1.12.00
G 1337.42
D 1.12.00 WWE
P.S. apart the problem everything is function properly
and the solution
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe radio_1.11_greek but idont reset the qtek in first screen
and upgrate downgrate start all ok
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe MagicianRadio_1.12.10. uk but idont reset the qteki n first screen
upgrate from radio 1.11 to 1.12.10
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run HTCMAG_ROM_WWE_O5_251209
everything is ok my magisian run the new Rom
here..........................
HI i search forum and i dont find answear. I flashed many roms but i never had any problem with usb connection with PC. So when i flashed new ROM and kaiser restarted when the new ROM started to boot windows shows info "USB device not recognized" i tryied reinstal drivers, reinstal AS, tryied mtty method, tryied flash ROM from storage card (dont work, meybe i do something wrong i founded 1 thread but i dont know do it work). Guys plz helpp me sry for english i am from Poland.
medeis_jar said:
HI i search forum and i dont find answear. I flashed many roms but i never had any problem with usb connection with PC. So when i flashed new ROM and kaiser restarted when the new ROM started to boot windows shows info "USB device not recognized" i tryied reinstal drivers, reinstal AS, tryied mtty method, tryied flash ROM from storage card (dont work, meybe i do something wrong i founded 1 thread but i dont know do it work). Guys plz helpp me sry for english i am from Poland.
Click to expand...
Click to collapse
Go here- http://forum.xda-developers.com/showthread.php?t=396922
And look into the force-USB Hard Spl! You may need to change your Hard Spl! Remember to use jump spl to flash!
I usually just disconnect data cable>kill all the mobile processes on my pc using task manager>restart pc and it always works.
redbandana said:
I usually just disconnect data cable>kill all the mobile processes on my pc using task manager>restart pc and it always works.
Click to expand...
Click to collapse
Hey Red, I see you got your calendar working! Yea I have never had an issue with my usb, but I saw that he flashes alot and it kinda fit the explanation for force-USB!
dash... thx for link to thread but i cant copy nothing to my device..... and RUU aplication dont find any device, killing all proces of mobile dont work too....
medeis_jar said:
dash... thx for link to thread but i cant copy nothing to my device..... and RUU aplication dont find any device, killing all proces of mobile dont work too....
Click to expand...
Click to collapse
Can you get into the bootloader? Maybe reflash the ROM from bootloader mode!
I have harspl 3 56 flashed, the bootloader mode working, but windows dont reconigze my kaiser...
medeis_jar said:
dash... thx for link to thread but i cant copy nothing to my device..... and RUU aplication dont find any device, killing all proces of mobile dont work too....
Click to expand...
Click to collapse
no you don't kill the processes on your mobile. you kill them in your TASK MANAGER application in windows on your pc NOT your pcc/tilt/kaiser/device then restart your computer and connect once windows is fully loaded.
edit:
These are the programs that are running on my computer associated with data sync:
1) WmdHost.exe
2) mobsync.exe
I killed proces on my computer in task menager ;] restarted and nothing happened...
medeis_jar said:
I killed proces on my computer in task menager ;] restarted and nothing happened...
Click to expand...
Click to collapse
Try uninstalling activesync on your computer then re-install it! I have heard of that working in the Herald thread!
medeis_jar said:
I killed proces on my computer in task menager ;] restarted and nothing happened...
Click to expand...
Click to collapse
ok then open Windows Mobile Device Center on your computer>Mobile Device Settings>Connection Settings>Allow USB Connections
read my first post i tryied that,...
i tryied mobile center doesnt work too...
medeis_jar said:
read my first post i tryied that,...
Click to expand...
Click to collapse
doesn't state that in your first post. It just says you never had a connection problem.
If you manually go into bootloader and have data cable connected does it say serial or usb at the bottom?
redbandana said:
doesn't state that in your first post. It just says you never had a connection problem.
Click to expand...
Click to collapse
Hey Red, happy 1000 post day! Your bigtime now!
Yes but i wroted that after flash new rom i had and tryied reinstal AS ;] sry for missunderstanding
in bootloader write usb when is connected, when i put of cable write bottom
dashmaster1000 said:
Hey Red, happy 1000 post day! Your bigtime now!
Click to expand...
Click to collapse
thanks dash and thank you for all the suggestions regarding the calender
medeis_jar said:
in bootloader write usb when is connected, when i put of cable write bottom
Click to expand...
Click to collapse
Then you are connected to your computer even though it doesnt say on computer! Go ahead and flash a new ROM! As long as your bootloader says USB you can flash!