Hi brothers and sisters,
im using O2 zinc with crumzz wm6.5 for around 1 month (with 3 or 4 hard resets). I all of sudden have my mobile continously vibrating with orange led always on, when the fones in power on. Is it a virus, OS problem or hardware problem ? I did not bang nor did the mobile have any rough falls before the problem started. After keeping my mobile off for some hours and then power on, the the vibration dont take place until a key is pressed or something. The led is always on orange. I tried hard reset (clearing storage). The vibration continues even while hard resetting and after.
Any solutions ?????????
Now i have a little improvement. The vibration happens only when connecting with the usb or charger. The led orange is fluctuating and led yellow is blinking from background.
I also re-installed the os. no difference.
re-installed OS meaning flashed a different ROM? if so, it might be a battery issue.
if you didnt' switch a ROM.. you should try
i flashed the same rom. What could be the battery problem ? no problem with battery life.
can't exactly tell you what the problem is..
and i suggest you flash a different ROM to see if it still vibrates.. if it does, it's your device, if it doesn't, it's the ROM.
Related
I had about two hours left on my XDAII battery when I switched the device off. When I then tried to switch in on, probably two or three hours later, it would not switch on. The green light was blinking as it normally does when the phone is on. I plugged in the cable to charge it, but the light did not change into a steady green (or is it yellow?) as it does when you're charging. I didn't want to hard reset it because I would lose some data, so I took out the SIM card and put it back in, as this normally soft resets the device. Instead however, it hard reset it, and I found the main battery to be empty. This still shouldn't have hard reset it, should it, since my back-up battery was full?
This has happened twice now. I'm starting to suspect that something is draining the battery even when the screen is switched off. Has anyone else experienced the same?
This may be obvious and you already know but it's worth considering.
When you switch off are you sure that you are turning the XDA II off or are you just turning off the backlight?
A quick press of the off button turns off. An extended press just switches off the backlight and the XDA stays on, draining the battery.
I've made this mistake too, especially in low light conditions. Hope this has helped.
Yes, that must be it! I had no idea that the off-button behaves like this! I don't think it did on the XDAI. Thanks a lot for this information, I will now be very careful with how I press the button, and check the screen in good light just to be sure.
I have a mda and the bluetooth light (the physical blue one) is stuck on, ive taken out the battery, done a soft reset. Turned on/off bluetooth. Even on standby the light is on, what should I do.
i think it is a software related so i suggest to flash another rom
I was thinking that but it wasnt like that for months, so there has to be a setting somewhere or something i can do....i hope
okay strange....randomly the light went off and its back to normal, only blinks when bluetooth is on....strange wm errors never seize to amaze me.
Hi!
I have a HTC touch Cruise for about one month now. Starting with last week it started to say that the "main battery is low, device will close" even if the battery is charged (even pluged in). I tried soft reset, battery out, hard reset, nothing. So I decided to reflash it. Now, it gets to the Windows start up screen but after I can hear the sound for turning off device, and the phone turns off for no reason and without a message.
The original language was french, and it was flashed with a english version and olipro spl.
Does anyone has a idea how I can recover my phone ? I have tried to load several roms, none of them worked.
Please help,
Thanks
I have the same 'Main battery is very low' problem on my TC, even when the battery is almost full. I have this issue on Bepe's ROM, ASerg's ROM and also on the official HTC WWE ROM.
It occurs frequently when I soft-reset. When it happens, I can only succesfully start my phone after completely charging it (LED turns green).
I think it must be a hardware problem in my TC. Switching the battery with another TC-battery did not fix it.
Can't you use your phone at all?
Seems like I got the same problem as you guys http://forum.xda-developers.com/showthread.php?t=402765
Any solution yet?
Is it the same on your side, that when you boot up with the Charger plugged in you don't get past the first splash?
Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks
If the accu not charge, I think he is dead. You need a new one. For flashing new rom, you need a good acco over 50 %. Than you go to bootloader modus and flash a WM5 Rom WM5Rom.
coolb4all said:
Hi All,
I've tried to upgrade the ROM of my QTEK S200.
It got completely stuck!!! I had to remove the battery. Now it stays black. Even a hard-reset does nothing. No bootloader, no white screen, nothing. It's like the device doesn't recognize the battery anymore. Same problem with another battery. When I connect the power supply, the light stays red for 5 seconds and then goes out again. No charging (orange) light.
Does this mean that the device was short-cutted (hardware problem) or can this be fixed with some manipulation?
Anybody an idea how I can fix the hardware (if broken) myself? Can't be to difficult if it just blew a fuse ;-)
Thanks
Click to expand...
Click to collapse
Yep, hes dead alrite, make a good paper weight sorry bro...
not the battery
of course I tried a new battery
same problem
Can you make a downgrade to WM5 ? Ist the battery charged now ?
DC Adapter 4,5 V
I had the same problem.
Remove the battery and connect the pin nr 1 (nearest to the cam) to + and the pin nr 5 to -. I think 3,7 to 5 V is ok. Then bootloader and connect to computer.
Don't blame me if anything goes bad ;-)
how to proceed?
I've tried to do as explained...
I've taken an old charger (5v) and connected the cables (black/white striped to 1 and black to 5). I'm not 100 percent sure about + and -, but normally black is always -, if I'm not mistakin'
What should happen? How should I proceed?
My device does nothing... No light. Power button does nothing, hard reset does nothing.
Does this procedure work with a QTEK S200?
Maybe the charger (old gsm) is too old or broken?
Maybe + is black...
Sooo many options ;-)
Worked on mine S200
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?
JustBored said:
Of course You must know if the adapter is working and +/-.
When I connected 1 to + and 5 to - I could operate the mobile as if the battery was mounted and working.
My problem began because the battery isn't charging in bootloader mode.
And I'm still stuck there... Because it's a G4 device flashed with G3 SPL... Anyone got a suggestion how to solve this?
Click to expand...
Click to collapse
I Did the same thing '''''HELP"""
What you should do
Keep the device on for 2 hours connect it to the electricity.
Install the original rom with the PDA connected like that to the PC, if it does not enter the Rom update continue trying by doing a hard reset with the stylus and pressing the left com button on the left side of the device, then retry the rom install, if it says unable to connect continue trying, using the procedure i explained before, thats what i did when the same stuff happen to me i was without my device working for a month, now i´m using WM6 with the Diamond Rom, so its possible, to do this you just have to keep trying.
my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?
srbwap said:
my prophet is block and after try of hard reboot is dont turn on.. its not turn on on any way, no detect charger ether ( no red led ) battery was almost full when its go off..
plz help, can i try 1-5 pins solution?
Click to expand...
Click to collapse
My friend. A few people have tried the pin method and one or two have succeeded. IMHO i would not try it, for fear of frying your phone, yourself or starting a fire.
Take out the battery for a good couple of hours. Take out SIm card and SD card. Put battery back in and try to charge for at least 5 hours, even if the light does not show (might just be LED issue).
Then see if you can start in boot loader, u now how to yes? (keep camera button pressed, soft reset with stylus, then let go of camera button after few sconds). What happens?
pins to power
I've tried connecting the extreme small pins to the (big) cables of the charger but nothing happens over here. The screen stays black.
To All,
Any hints on how to connect these cables to the pins, without the fact that they're constantly coming off the pins and constantly touching other pins?
You try and tell me about your experience ;-)
revive prophet revive ;-)
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))
coolb4all said:
I was just playing with my qtek when I noticed that after connecting and disconnecting it to the AC for 5 times or so (with red light going on and off for a second), it tries to startup, but drops dead after a fraction of a second. Damned ;-) No chance of going into bootloader.
Almost there ;-))
Click to expand...
Click to collapse
keep it plugged in for about 5 hours, dont play with it or turn it on lol, give a go unless u have done already and just havent said
Direct Connection to 220v doesn't work
The workaround of connecting the pins directly to the charger doesn't seem to work on a QTEK S200 G4.
Since mine is a G4, I wasn't lucky... I'm left with a cut charger cable.
I'll try to charge it for 5 hours but since no led is going on I don't think this will have any effect.
Listen keep it plug in to the electricity for 12 hours, then try to put it in bootloader mode by pressing the, com button on the left side of the device after you hard reset it, with the stylus after you manage to enter the bootloader mode, you only need to follow the steps described on several posts on the forum.
if nothing works connect the device and try to install the original rom, my device is a g3 so i´m not sure if the g4 works the same way.
Hi
suddenly from today i have a led light turned on inside my front speaker
i googled and found this
http://www.techdroider.com/2015/08/moto-g-3rd-generation-also-have-hidden-led.html
I have purchased the phone on 26th Oct 2015 from Flipkart.
No matter what I do the light wont go off. Even if i power off the phone the led stays.
Please let me know what to do.
justrajdeep said:
Hi
suddenly from today i have a led light turned on inside my front speaker
i googled and found this
http://www.techdroider.com/2015/08/moto-g-3rd-generation-also-have-hidden-led.html
I have purchased the phone on 26th Oct 2015 from Flipkart.
No matter what I do the light wont go off. Even if i power off the phone the led stays.
Please let me know what to do.
Click to expand...
Click to collapse
Disconnect your USB cable, is it still lit? The LED is a charging indicator in some ROMs but the fact that it is on when powered off is odd. If the LED is lit and no USB cable is connected and the power is off, this sounds like an electrical issue inside the device but to be sure I would do a full factory image flash and test it.
We all know it has an LED, have for some time... but it is hard wired to the charging circuit so when activated it only shows charging status and nothing else. If yours is one all the time, it could indicate a problem with the hardware.
acejavelin said:
Disconnect your USB cable, is it still lit? The LED is a charging indicator in some ROMs but the fact that it is on when powered off is odd. If the LED is lit and no USB cable is connected and the power is off, this sounds like an electrical issue inside the device but to be sure I would do a full factory image flash and test it.
We all know it has an LED, have for some time... but it is hard wired to the charging circuit so when activated it only shows charging status and nothing else. If yours is one all the time, it could indicate a problem with the hardware.
Click to expand...
Click to collapse
Hi
It glows without any cable attached. I will go ahead and file for a replacement.
that is scary can you take a snap of it ?? i want to see how it looks
nandakis4 said:
that is scary can you take a snap of it ?? i want to see how it looks
Click to expand...
Click to collapse
It looks white. Even mine just flashed up one day for 0.5 seconds. You can do it to. Just discharge your phone completely until it turn off automatically then goto a very dark room cause the light is to dim and then plug your phone. You will see it flashed up for one second
Does that mean a USB cable isn't required to make it glow
Since you can't touch the battery, I suggest you discharge it it completely . Keep it mines it can be dangerous though.
Hi
It glows even if i switch off the phone. I have asked Flipkart to replace my handset. But they were trying to say that i should take it up with the company. I was stern and asked them to replace it since it is just 15 days since i brought the phone. They have told me that they will send the engg. tomorrow. Will keep you guys posted.
http://imgur.com/Z168hK4
Awesome.. I want thay
Did you get this issue fixed ?
Same issue !!!
Even I have the same issue since yesterday .. LED is always ON even after powering off the device. Any Idea how to resolve this issue ??
Did you get any solutions for this ?? I am also facing the same issue , I did a factory reset. But the problem still exists.
justrajdeep said:
Hi
suddenly from today i have a led light turned on inside my front speaker
i googled and found this
I have purchased the phone on 26th Oct 2015 from Flipkart.
No matter what I do the light wont go off. Even if i power off the phone the led stays.
Please let me know what to do.
Click to expand...
Click to collapse
See here on XDA:
http://forum.xda-developers.com/mot...m-controls-t2951869/post57014759#post57014759
It's applicable also to Moto G 3rd gen.
If with
echo none >/sys/class/leds/charging/trigger
LED stays on, it must be an hardware failure.
I have the same problem! Since two days ago the front LED is always switched on!
Weird, it popped up just an hr ago in my moto g, gen 3 as well bought in India, via Flipkart and won't go away. It has a flickering (seemingly pseudo random) characteristic in periodicity as well as luminosity potentially indicating a short-circuit of led power-circuit behind front speaker(s) or worse, some fourier optical-transmission pattern. It flickers even when powered off and that says something about this LED behind front-speakers. A factory reset also did nothing to it.
Hey guys! I aslo facing the same problem.i tried every thing except Root. I have tried power off, battery 100% drain,factory reset but nothing can stop led. please suggest if any one have its solution
i have tried these apps, and one of the kernel for our device can turn it on without any app, but what i want is enable without any mod or app.
gunjan.kumar said:
Hey guys! I aslo facing the same problem.i tried every thing except Root. I have tried power off, battery 100% drain,factory reset but nothing can stop led. please suggest if any one have its solution
Click to expand...
Click to collapse
Hey man did you managed to solve this issue? My led started glowing a few hours ago, I have 3 months with the phone.
Hi all,
is the issue still solved? today my phone has started to show the same thing,even after it's powered off the led still glows mildly. it's been 5 months i'm using it. I've wiped data,cache,system parititions then flashed a stock LP rom but the issue still exists. From custom Kernel if the 'Battery Light' option is turned ON when the phone is being charged it glows brightly. It's really uncomfortable to see it's lit all the time. I wish I could have removed that LED light from there lol
Anyone please have a look
Hi!
I have the same problem with the white led. I contacted Motorola Support (in Canada) and I got to send my phone to a service center. I just got my phone back and they say it's not repairable because of a liquid damage to the main board. The thing, my phone never got wet!
I don't know if others who contacted Motorola got the same result...
I just had one start doing it too... if warranty won't replace it then I think I will damage the LED to try and disable it to hopefully rid of any extra battery drain.
EDIT: Well i'm not sure about this because i was thinking about drilling with a super small bit down to the LED to disable it, however i don't know how the earpiece speaker functions and whether it would damage it's function as well.