Hi all,
i was cleaning the keypad, home key was stuck and i broke the ribbon cable. long story short, i need to remove the mainboard. i did find a post on Modaco on how to open the sp5 but its not working for my case for some reason.
I actually have managed to open the whole case and see the whole mainboard + exposed lcd but it looks like the mainboard is jammed from one end (base of sim slot/keypad ribbon cable). i dont see any plastic latches, dont see any screws but something is holding onto the mainboard. dont want to pry it too hard, it might rip the base or the mainboard.
Any suggestions?
Try here:
http://sdadisassembly.blogspot.com/
Step #8
Holy Macaroli. there was a screw under the warranty sticker i never found until i saw the previous post! Thank you!!!!!!!!
AtlzBest26 said:
Holy Macaroli. there was a screw under the warranty sticker i never found until i saw the previous post! Thank you!!!!!!!!
Click to expand...
Click to collapse
I'm surprised you got it open enough to even start asking about the removing the mainboard if you hadn't gottent the warranty void screw.
BTW:
Warranty's now screwed.
LoL...dont care about warranty since the phone is now over 2 yrs old anyway.
And i had my baby lessons from the modaco forums..
ok that T5 screw is jammed stuck and looks like its gots its sides rubbed out from previous times (it was repaired under warranty so those techs mustve messed up the screw). philips flathead and t5 torx is not working, any other options?
AtlzBest26 said:
ok that T5 screw is jammed stuck and looks like its gots its sides rubbed out from previous times (it was repaired under warranty so those techs mustve messed up the screw). philips flathead and t5 torx is not working, any other options?
Click to expand...
Click to collapse
The techs who stripped the head probably used lock-tight.
If nothing else has worked (because of lock-tight), then my wildy stupid and dangerous idea would be to break a small guage drill bit (not driver bit), file off the rough edges and place in the drill chuck backwards. Drilling a hole in revers should spin the screw out. Or allow a different driver to fit.
I wouldn't actually recommend this....
I was gonna do a DIY, but no need.
Note: Doing the below Voids Warranty do it at your own risk.
And wear one of those anti static thingys around your wrist!
Raphael Service Manual.
http://www.touchpro.cz/data/download/4/htc_raphael_sm_a10__generic__01_dec_08.pdf
And Marks guide for replacing the camera but it works pretty well with the service manual to ripping your raphael apart.
http://www.mediafire.com/file/h2mmw... Camera removal photo guide v1.1 by A Mak.pdf
Site that has parts for the Raphael.
http://www.gsm4world.us/shop/touch-raphael-c-210_405.html?osCsid=eea3575cd78bee70a7707c419282d2b7
--------------
Navi Key buttons Fix.
Repair manual says it has to be baked to remove? well hey its only stuck on there with double sided tape. So order up a new one and slap it on there!
No more face getting scratched or cut up.
-----------------
Slide Mechanism not firm enough for you? Well Tone like you tone stuff at the gym, or when your printer runs out of toner.
Rip your phone apart following one of the manuals above.
Get to the slide mechanism part and youll notice there are three coils, take them off and bend them to your liking, reinstall. DONE.
Hi,
I wonder if someone can offer any suggestions... The end of my stylus has broken off and left the metal part right inside the phone. I've tried with jewellers screwdrivers and tweezers to get it out, to no avail.
Any suggestions?
Have a look at the Polaris Wiki and get the service manual to disassemble the case.
Happened to me yesterday .Get a needle,press point of needle againt stylus.then push it out.took me 2seconds.
If the needle trick doesn;t work I somehow used a needle to prize the chamber open via the side and then freed the stylus by sliding it down. It hasn't damaged my polaris in any way. Sorry can;t be more specific but it wasa while ago!
Another way would be to take a bit of wire or a cocktail stick, apply a small drop of super glue to the end and press it onto the broken end of the stylus (being careful not to touch the sides of the polaris)
Then wait a few seconds for it to dry and pull it out!
Dear Nordberg !
try to put some glow on the top of the rest of ur stylus and put it back in ur PPC, let it a few minutes then try to pull it slowly and u will have a one piece stylus ......
Alright, I did send sms on my bicycle which resulted in I did drop the phone on the ground. Luckily I had ad NILLKIN glass screen protector, which did save most of the phone . I have ordered a new Nillkin screen protector from Aliexpress. And I hope to patch up this phone so it looks good again. How would you have done ?
As you can see at the bottom in the pictures there is physically damage, you can you see the screen bleeding thru also the huwawei logo is damaged.
My idea is UNDER the NEW Nillkin screen protector I will try to mask these "holes" so the screen is not beelding thru anymore. What material should I use to patch up these holes.. also.. how to repar the logo ? can I print it out on my computer printer ? it might look **** on paper but UNDER the glass protector it might look a lot better.
All creative ideas are appreciated, I have high hopes the phone will look good again..
And hopefully my phone will surrive until the M8 release.
Just to let you know desipite the glass look damaged like this the phone is still fully functional!!
ouch i can feel with you.
How about some black film, black paper or everything else that is black and thin
Yes some black material for sure.. Black film would be perfect in guess.. Just wonder where to get it also some black glue at the sides also..
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
alexre123 said:
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
Click to expand...
Click to collapse
Nice man might be a very good alternative! But how easy is it to change it really?
Do I need a heat gun for that?
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Or...if you have the courage go for it ) - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Joke man, don't do it yourself if you don't have experience
alexre123 said:
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Click to expand...
Click to collapse
I have done some smartphone repair myself, I changed the USB board on my old Galaxy Note 1.
I bought a smartphone repair kit with a few tools and very small screwdrivers. To change the glass is probably not much harder, but I need to know if I need a heat gun since I do not own any yet Hopefully it is not needed..but I would assume so...
I might also add the reason I bought a screen protector was that the original glass underneeth have a small crack too that goes accross the entire screen but it s quite invisible besides from certain angels.. so to change that screen to would actually be amazing..and it would make the secondary value when I sell this when M8 is released be a lot higher..
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
alexre123 said:
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
Click to expand...
Click to collapse
Yes the Nillkin glass did its job but I think I was unlucky, that the bottom of the phone got under my bicycle tire.. it felt like it...
I recommend Nillkin, IT has very good Oleophobic coating, which makes the whole device a lot more enjoyable to use, but be careful whren you put it on non 100% straight surfaces it will slip onto the floor.
Alright it is more or less decided I will buy a new front cover with glass, I will make sure to get original parts with gorilla glass. Since the ebay link you linked to are chipped from china I guess I can just order straight from alixpress instead...
I have heard singapore post have quite fast shipping compared to china post.
just one question is hard to see in the videos.. but do I really need to disassembly every component all the circuits boards just to change the front screen ? do I need to open the case at all when using the heat gun/hair dryer ?
If as in the every component and circuit board has to be disassembled it is over my competence probably... unless I am super careful..
Mutch better if you want to purchase an original front to replace it. Don,t know if you really need to take all the components of for replacing the front screen, but you can make some research on it or you can ask on other forums, maybe are others with more experience.
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
blackinfinity said:
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
Click to expand...
Click to collapse
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
ehhm... good luck OP
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
blackinfinity said:
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
Click to expand...
Click to collapse
Sorry but you are like 10 year old child..
So u wanna change your ''front Screen Outer Glass Lens'' ??? (that is damn long name for glass )
You have so much hopes ? OK .. go on .. I leave you to it ..
I wish you very best of luck ..
''''IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT''
DDDDDD this was so funny :laugh: :good:
Fingers :fingers-crossed:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
blackinfinity said:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
Click to expand...
Click to collapse
And I will give you one last advice ; that my detailed post above I explained you how difficult it is .. YOU want to change glass only ??
And what you think, you can just do it without stripping phone apart ?? Are you magician ? You would have to open phone anyway !
And replacing glass on your screen, do you have any idea how you gonna do it? Removing glass from LCD is x10 TIMES hard that my instructions above man !
So you basically adding even more, harder work to hard work ..!
Do you even have
1.LCD separator heat machine ??
2.Cutting line wire ??
3.Cleaning alcohol chemicals ??
4.Optical clear adhesive glue ??
5.Ultraviolet curing lamp ??
Come oon man ...
I told you I wish you very best of luck..
This guy want to do the exact same thing - https://www.youtube.com/watch?v=O8HNBtl9MwI
You have the all process here - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Take a look and decide if you want do it yourself and risk to mess things up or go with the phone and the replacing part to a service and let someone who did this before.
Hi guys
Sadly I have a cracked display...so there are no spare parts available and the shops in Germany would like to have something around 500€.
I changed in the past some Sony-Displays and thought about doing myself. I found on aliexpress some U12+Displays.
Sadly I didnt found a single "manual" or how to, to do this right - anyone can help?
Best regards
Maybe these vids from JerryRigEverything can help you out.
Good luck!
Sent from my HTC U12+ using XDA Labs
https://tinyurl.com/htcu12
Just replaced mine
majomathes said:
Hi guys
Sadly I have a cracked display...so there are no spare parts available and the shops in Germany would like to have something around 500€.
I changed in the past some Sony-Displays and thought about doing myself. I found on aliexpress some U12+Displays.
Sadly I didnt found a single "manual" or how to, to do this right - anyone can help?
Best regards
Click to expand...
Click to collapse
I just replaced mine yesterday and it was more difficult than any other one I've done in the past. Anyway I never found one single video on YouTube that showed the screen removal and pretty much had to play it by ear. There are a few videos that show the disassembly of the U12+ and each stops before removing the screen. My advice is to remove everything from the frame, I managed to piece together enough from the videos to know there are 15 screws to remove, one video said 14 but there's one more that's hidden until you've gotten under the motherboard holding the front facing cameras. Knowing I wanted to keep it simple I didn't remove all of the antenna wires, there's one at the bottom that's under the speaker cover that I left attached so I only disconnected it from the motherboard. Then the other I only disconnected near the vibrator, leaving it connected at the motherboard, so each piece had one wire that stayed connected. Meanwhile you'll have to undo every other plug on the device and with a little persuasion everything fell out. (Don't attempt to remove the button/pressure sensing strips along the sides!) Once you are down to the frame, and for me the ear piece speaker, I used a heat gun to soften the bond between the glass and the frame. It doesn't loosen up very easily, they are really bonded together. I got most of it and then began to chip away at the broken glass. You'll want a good heat gun for this part. I had to set mine to 300F to really get it to loosen up and then work mm by mm around the edge getting all of the glass and glue out of the track. This probably took me a half hour or more. I used E6000 glue but only because I would have had to order B7000 or any other recommended glue. E6000 is a good glue but just because many of the other videos I watched used B7000 I would have liked to use it too.
To install the new screen I used a syringe filled with my glue to follow the small glue track around the edge of the frame. Don't worry about squeeze out because this glue is very forgiving and wipes away easily with IPA Alcohol and a rag. I followed the old glue placement, adding a little extra near the bottom corners and a dab around the ear piece speaker holes. Then it's just reversing the process to assemble the electronics. Now here is another word of warning, the plugs are so small and some are not easy to align but be sure they snap into place and are flat when installed. I made the mistake of not getting the display plug flat and had to do a partial disassembly to correct the issue.
I didn't glue the back on but think I might today just to try and achieve the waterproof level the phone shipped with. You may have to glue yours but I had previously broken the back and already replaced it and the replacement came with a double sided adhesive strip that was still pretty sticky. If I remember correctly the original back was glued on and probably wouldn't have stuck if I had tried to just replace the back as I did.
One other note. After being disassembled and pulling the battery my finger print scanner didn't want to work. In fact it didn't even show up in the menu when I went looking for it but restarting the phone again caused it to show up. My advantage with the double sided adhesive was I was able to test everything and use the phone for a full day before committing to gluing the back on. Now that I know everything is working, the phone is charging and it all seems good I can glue the back on.
Best of luck