Ok so I have a little problem with my HTC Diamond. In options I set to turn-off the backlight after 10s of inactivity which is standard. The problem is that after those 10s I can see that the screen backlight is fading out but it doesn't fade out completly - if you look from an angle it might appear that it's off but if you look at the front of the phone or simply in the dark you can see that the backlight is still on only set to something near 10 or 5%. As you know the battery just sucks in this device and I don't want the backlight to drain it so any ideas or tips on this matter? Of course I can put the phone to sleep mode but I'd just prefer to make the backlight turning off so I can take a look at the screen to for example check the time without having to press any buttons...
Same problem here
After those 10s the screen is not turning off completly, just fading to 5, 10 %. The screen with all the info, the home page let us say, is still visible and drains the battery. I also could just press the power button to turn is completly off, but I would also prefer it to do this manually after ten second.
Did you find a solution to this problem yet?
Help Battery Drain
Same thing here, and my Backlight is stuck to 100% i think,
anyone found a solution to this? any hints?
Guys, i assume youve set the "turn off device if not used for xxx mins" correctly whilst in battery and external power correctly?
If you have, what roms are you using as you give us no information to help any further
Hello,
I had the same problem with ROM 2.03.421.2, date 12/24/08.Back then I had SPB mobile shell installed and a very few applications and I couldn't find the problem. I made a hard reset so now, with nothing installed, the device also enters standby. You should take care because it is possible that the device is not entering standby either and it is making calls. When I had this problem my friends were complaining that I kept calling them and not talking. It is strange as I'm sure I put the device to sleep with the power button. But still, somehow, it was making calls...
Related
When my phone rings, the screen turns on. It doesn't matter if I lock ir or not. The Answer and Ignore buttons are still pressable on the screen. Is there any registry setting I can change to make it so the screen stays locked when the phone rings?
I still want to have the option of pressing the Answer and Ignore physical buttons on my phone, but I keep accidently hitting answer or ignore on my screen when pulling the phone out of my pocket.
Thanks
If you install ACs Slide 2 Unlock then you will need to slide to answer or ignore a call. Should stoip the accidental pressing of on screen buttons.
That is not an option. It cuts my standby battery life down to half a day. w/o it I can standby w/o recharging for about a week including phone calls. I probably only talk on the phone a few hours a week though.
BTW I failed to mention that I am on WM6.1
What exactly what you like to do?
If you use a regular dialer the phone will turn on anyways.
If you want something else, like S2U2.. you'll have to accept it's requirements.
Tho, I'm not aware of the battery drain issue. my phone's running S2U2 and it's fine.
try playing with the preferences.
AT&T Fuze screen issue - bottom menu-area of screen is flickering almost constantly
(Forgive me for the length of this post. I am just trying to provide as much information as possible! If anyone has encountered this same or similar issue, your help is greatly appreciated).
I need help! (professional and otherwise) ...with my AT&T Fuze (rebranded Touch Pro).
I am developing a game for Windows Mobile called Scrobble (http://forum.xda-developers.com/showthread.php?p=3206316&posted=1), and I left it running overnight.
My screen is set to turn off after 1 minute, and my device set to sleep after 5 minutes when plugged in to external power.
I had the Fuze plugged into wall outlet power to recharge. I left it lying, like I always do, face down on a black soft-leather CD case (so the glowing charging light doesn't bother me).
I left it alone for the 7.5 or so hours I was asleep. When I woke up in the morning and picked it up, the screen was on. It usually is not on, and I don't think I pressed the button to activate the screen.
When I looked at the screen, the Scrobble program was still running, and the bottom menu portion of the screen was flickering. Scrobble has two menu buttons at the bottom -- "Turn" and "Game" -- with a SIP keyboard icon in between them (same as nearly all WM apps).
In any other program, or the Today screen, the menu portion of the screen flickers (the brightness constantly and rapidly fluctuates consistently... like a fluorescent light that is on its last leg).
I did a full power off and power on, and during the "world phone" screen and the the AT&T 3G "power up" animation, the flicker was -not- there. But as soon the Windows Mobile loading/splash screen appeared, the flicker returned, in the exact same spot.
And I can see the ghost "Turn -- [SIP] -- Game" menu in the flicker. But I don't think it's burnt into the display, because it's not there during the first two loading/splash screens.
Currently I have the battery completely removed from the device and will leave it out for a while. If that doesn't work I will do a hard reset.
Any help would be greatly appreciated!! (This device is about 2 months old -- does HTC provide any support for it directly?).
Fixed
Phew! My screen flicker issue is no more.
I'm not sure if it's because I took the battery out and let it sit and think about what it had done for ~22 hours, or if it's because it just went away after a while (with the battery out for 22hrs). But either way, my Fuze is back to normal!
So if anyone leaves theirs on overnight and wakes up in the morning to a flickering ghost of a menu at the bottom, my suggestion is to fully reboot it, then take the battery out and leave it out overnight!
(It's kind of nice going a full day without any phone calls!!).
good for you.. you dont need a new phone giving you damage issues already... glad to hear that its gone
Thanks you for this post. I am going through the same thing with my ATT Fuze. This time it is Tomtom that I left running overnight with the screen turning on and off. I can add that the flicker and ghost is there the second the phone powers on. I have already hard reset and took the battery out for a few mins, but the flickering still there. Now I will take the battery out for several hours and hopefully it will be normal again.
I had a similar issue this week. I was using the phone all day, getting emails and phone calls, no problems. I get home and go to charge my phone and it doesn't appear to be charging. I flip on the screen and the whole screen is flickering on and off like it's not getting enough power. I charged the device over night, hard reset, pulled battery for 24 hours and still it won't go away. I just got the device thru amazon so I already reordered a replacement.
I've never left my screen on for hours at a time and I sometimes run into that same issue. The bottom of the screen flickers, and I can see a ghost image of my left and right soft keys when doing things that pull up a dark grey or black screen, like adjusting the volume. I usually try a few soft resets, and if that doesn't work I turn it off and take the battery out for a while. From what I am reading it seems to be correlated with extended periods of screen usage, but my screen has rarely been kept on for more than 30 minutes at a time.
Not to beat a dead horse or anything, but I was just having the same problem with my Fuze: the bottom quarter of the screen was flickering, but without the ghosting you spoke of. Out of curiosity, I went into my "Power Settings" menu, and for some reason the "auto adjust backlight" was unchecked, and the brightness settings were maxed out. I checked "auto adjust backlight" and the flickering stopped. Not sure why, but thought I'd add it to the thread.
kart_racer3 said:
Not to beat a dead horse or anything, but I was just having the same problem with my Fuze: the bottom quarter of the screen was flickering, but without the ghosting you spoke of. Out of curiosity, I went into my "Power Settings" menu, and for some reason the "auto adjust backlight" was unchecked, and the brightness settings were maxed out. I checked "auto adjust backlight" and the flickering stopped. Not sure why, but thought I'd add it to the thread.
Click to expand...
Click to collapse
Yeah I did notice that it's only really noticeable when the screen is set to max brightness. Setting it on auto adjust cleared it up for me also.
proj3ktpat said:
Yeah I did notice that it's only really noticeable when the screen is set to max brightness. Setting it on auto adjust cleared it up for me also.
Click to expand...
Click to collapse
thx guys...helped me out too...
Just sent my unit in for repair (under warrenty) due to the screen flicker issue, lets see what happens when it comes back.
I just started to experience the flicker today. Has be somewhat concerned. The device is only two weeks old.
However, it seems to have stopped by itself while I was searching the forums for an answer. If it returns, I'll try the 'remove battery' method and see if that helps.
Also, I love Scrobble! Shame it doesn't work on QVGA displays. Or, at least, didn't on my Wizard...
Related thread
Hey guys there's a thread with the same exact issue and a screenshot on the first post.
http://forum.xda-developers.com/showthread.php?t=535099
Seems to be something related to the Hardware 3D Acceleration driver for Windows Mobile, I get this problem only once 3d has been activated.
If Sense/TF3D is turned off, I never see this problem. It only comes up once a game or Sense has been launched.
I can also boot into Android without 3D activated and not have this problem, but if I run Sense then go into Android I get the flicker from a Windows Mobile screen while in Android.
protwitness: That doesn't seem to be the case (for me, at least.) I don't run TF3D and it still happens. I can't really discern what the trigger is, but I have a feeling it has something to do with the screen brightness auto adjustment. (Sometimes, I'll turn my phone on when it's dark and it jumps to full day-light brightness for some reason.)
I've adjusted to it and it doesn't really bother me any more.
Hi guys, I find this quite annoying and wish there is a mod for this. I don't know about other HTC Touch Pro owners but i find my fone quite sensitive.........it's "EASILY" turned on by a single "SHORT" press of the power button.
I didn't even hold it for 1 second, if i suddenly press or tap on it really quick, for not even a second, it turns on.
In case ppl don't understand and tell me that maybe my fone was on in the first place but just have the backlight off, and with a single tap on the power button, the backlight goes back on again. I knew that already. But what the problem really is, is that it's totally off, and when i tap the power on button, it turns on, i.e it vibrates and shows the welcome screen and all that other startup animation.
Is there a way to increase the delay of the finger-press on the power button? Coz it's so annoying that it gets turned on when i don't want it to, especially since this fone's weakness is that it hogs battery even though i've already applied tons of tweaks etc to lower the performance and increase battery life......
Oh and i have another problem, i find the signal kinda weak, is there a program or tweak to increase the signal?? Coz on my old phone Sony Ericsson W950i, the signal is great and I never have bad signal problems with it. But using HTC Touch Pro, i have this problem. This only happens when i'm at Uni, but it's not like they have bad reception or signal blockers there like how schools or colleges have. Just that when i'm inside buildings and there're tons of other buildings around, i can't send the txt coz of bad signals and it's bloody annoying, but using my W950i works fine.....
also I noticed that when i type a txt message using the hardware keyboard, it seems to fail to send most of the time, but only when i'm in UNI. But if i switch to the software keyboard, the one that you use ur fingers or stylus, then when i send the message it often works compare to using hardware keyboard.......any ideas?
Problem No 1: Try Touch Lock Pro
Problem No 2: Try to burn the newest RadioROM.
thx but i'm not trying to lock my phone, so i don't think TouchLock Pro is what i need.......
My Raphael turns also on after pressing the power button for a little few moment. With touchlock Pro you can prevent that you mistake your Raphael. I hope you can understand what I write in my "own" english
Ok so i've got it installed now and went through all the settings but couldn't find anything that can delay the power-on button press, I still have this problem. The app is a screen-lock app, there aren't any options regarding to power-on delays.......
plz tell me what settings etc to use.
I've never said that you can fix your problem with TouchLock Pro. With this you prevent to use your Raphael when you press your power button accidentally.
ya but that's only useful when my fone is on and it locks the phone but i'm trying to prevent my fone from turning on in the first place if i accidentally press the power on button for not even 1 second, because then it will turn on and i don't want that.
same problem here...the phone I thought I had turned off was back on, because accidently it got touched by something else in my luggage.
The only solution which to me is unsatisfactory, is to take out the battery so that it cannot power up.
C'mon...there has to be a better solution than this, no???
jewelkobayashi said:
same problem here...the phone I thought I had turned off was back on, because accidently it got touched by something else in my luggage.
The only solution which to me is unsatisfactory, is to take out the battery so that it cannot power up.
C'mon...there has to be a better solution than this, no???
Click to expand...
Click to collapse
wow yay finally someone else other than me also report having the same problem, boy am i glad to know that i'm not the only one having this problem, i thought it was just something wrong with my fone and not all HTC Touch Pros....
i can't believe there aren't any results on Google, no forum discussions or solutions to this whatsoever. Also, nobody seemed to report this problem or come up with a solution on XDA as well as other forums i use like PPCgeekz or WMusers etc.........which is odd considering how this problem is quite annoying, that if u suddenly power on the fone by accident, it can drain battery life and god knows HTC Touch Pro has a crap battery life.............
I think that htc has done a bad job testing the powerbutton on the tp2.
There are some other things like weith, thikness and batterylife that could be improved but the powerbutton issue is realy a BIG bug.
Why they didn't make a slidebutton or a timeout between push and activation?
A dobble tap on the powerbutton could also be a solution.
The next rom shoold have a improvement about this button.
People, please react on the powerbutten problem so someone can fix this.
Thanx
jewelkobayashi said:
same problem here...the phone I thought I had turned off was back on, because accidently it got touched by something else in my luggage.
The only solution which to me is unsatisfactory, is to take out the battery so that it cannot power up.
C'mon...there has to be a better solution than this, no???
Click to expand...
Click to collapse
Leaving the Touch Pro (Raphael) for some minutes without battery will stop the clock. So, when you put back on the battery and power up the device, the clock will display the wrong time. The time when you remove the battery.
This is hardware related.
Can produced different symptoms though.
Facts Behind the Power Button
If take a look at the inside of the powerbutton, there are 2 points making contact when you press the button. If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "QuickShutdown" message.
But, if water/alchohol/liquid gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
As a result, despite the fact that you hit hibernate/sleep/suspend on the hardware power button = yes, the screen fades to black. But IT IS STILL ON. That explains the battery being drained.
Solution:
Open the phone hardware. Clean the power button connector manually.
Disassembling Instructions:http://www.pdacenter.ru/razborka/htc-touch-pro/
Power Button Connector: http://kudryashovda.ru/content/ne-rabotaet-knopka-vklyucheniya-na-htc-diamond
off / on / off on
i heart everyone talking about the sleep of death and to be honest, i havent really experienced this, but i definatley do have an intermitent power on and off button problem on my touch pro 2.
i read on some other forum that it could possibly be the slider that is casuing the problem. but to be honest, the button its self feels fine and looks fineand when i does work it works a treat. i havent had any water damage done to it what so ever. so im not sure , i am new too all this self help mobile stuff. so please excuse my ignorance. Ive doen the usual hard reset, button works for a few hours then calls it a day. soft rest, was working up until this week. i cant get ot to boot up again, while fiddling with the batter and a power lead. but the power button is so intermitent its driving me nuts. id be so grateful if anyone could shine any form of light on this. thanks in advance
My XDA Serra (Touch Pro) will let me view the screen for about 20 seconds before it switches off. Not just a backlight dim, but a full switch off. If I keep poking the screen it will stay on, but then I end up selecting something on screen.
My settings for the screen make no difference and it's making the thing unusable. Anyone know of a decent backlight / power management software that can take it by the scruff of the neck and make it behave?
Thanks.
66mustang said:
My XDA Serra (Touch Pro) will let me view the screen for about 20 seconds before it switches off. Not just a backlight dim, but a full switch off. If I keep poking the screen it will stay on, but then I end up selecting something on screen.
My settings for the screen make no difference and it's making the thing unusable. Anyone know of a decent backlight / power management software that can take it by the scruff of the neck and make it behave?
Thanks.
Click to expand...
Click to collapse
Check your power off button isn't stuck pushing down forcing phone to turn off. It has reportedly happened on a number of other devices
No, I just checked. Seems to be OK. Thanks
Have you tried flashing another rom?
If not try that, and if that doesn't work, the lock button must make contact somehow as fallen spartan says.
Solved.
I had to uncheck all the power management crap, soft re-set, and then. Re-check the settings I wanted.
Don't you just love WM...?
I've had an odd problem with my 820 almost since getting. I'm hoping one of you geniuses have some advice.
When I turn it on it works perfectly, sometimes for hours. Then the screen goes blank, and then random pixels begin to appear, starting at the top of the screen. Outdoors rather than random pixels the screen goes almost totally green. Strangely, if part of the screen is obscured the green only covers rhe exposed area.
Pressing the on button repeatedly usually brings back the lock screen and reset (on+down) fixes the problem for another few hours.
By the way, eventhough I can't see the screen the touch sensor works. For instance I can hold theon button and then swipe downwards to turn off the phone. I can also answer and hang up using earphones.
My daughter who purchased the phone said it worked fine until the amber update. I had hoped the black update would fix the problem but no change. I found some posts from people with the same problem who sent the phone in to be fixed and got it back in the same condition. I really don't want to go through the hassle unless I expect to get it back fixed. I'd rather try fixing it myself.
My question is whether this is a firmware problem an whether it is likely that re-installing the stock black rom would do any more than the ota install that occurred automatically did (or didn't do).
Any ideas?
Nobody?
By the way it seems to happen only, or mostly when in standby.
I installed an app that displays a clock and doesn't allow the phone to go into standby mode,
and the problem doesn't appear to occur (unless I forget to leave the app on top).
I would set the phone to standby = "never" but the option isn't available on my phone, though
I understand that there are those with the standby = "never" option.
Any idea if I can set standby = "never" with keyboard commands, perhaps?