I have been having some problems today trying to connect with activesync. I plug my Kaiser in via USB, it starts to connect and I get the transfer arrows (top bar) for a second then it disappears back to a 'G'. Activesync continues to try and connect and my phone just sits there. Can someone help me please?
Related
this is my 3rd PPC and i am completely desperate about his problem which i never had before. i can not connect my JAMin trough USB or Bluetooth or Infrared, my activesync turns green but after 2 minutes trying to connect it says that can not get connected, also i have tried on my laptop and i get something else when i cradle with infrared or USB my windows crashed while sync. i have no Idea thought it is because of my Antivirus and AntiHackers i have installed on both computers but i get the same error even if i disable them, I have tried activesyc 4.1 and also 4.2 but same result again,
Any Idea????
--
Do you set IP-Protocol for the Network connection with the Windows mobile device in network connections?
activesync
sent you a PM hope this helps
Thanx s2tephen,
i have Uninstalled my Antihacker firewall and it did worked perfectly,
just close any firewall
and try again
it did work with me
Hi guys,
Hope you can help me with this one
I can't ActiveSync with my PC & Laptop. The computer re-starts everytime I connect my JamIn.
I used USB cable & bluetooth to Sync, I got same issue of re-starting with both.
Please help
Thanks
hey what's up?
Just wondering if anybody has had any problems with active sync lately. For some reason I can only plug my mda to the computer one time, and if I unplug it active sync won't recognize the mda again until after I restart the whole computer.
if anyone had the same problem I read through the site some and just go to connections to usb-pc and uncheck advanced networking.
I have tried everything, but activesync does not read my Tornado. I get to bootloader, (No device detected). Disconnected, reconnected, turn phone on and off. Reinstalled activesync multiple times. Tried on 3 different PC's and still no luck. SOmeone please help me. This post is part of the other 2 posts that I made.
Active sync will not show connected in bootloader mode. But as long as you have USB connection enabled in AS settings, then you are connected.
You will see USB in your phone above left softkey
My screen on my Fuze has suddenly stopped working and I would love to be able to connect to activesync with just my hard buttons if possible?
At the moment, it defaults to USB connection and that does not allow me to sync data onto my computer...my question is this:
Is it possible to connect to ActiveSync using a combination of buttons without the use of the screen? Please I need this as it is very important, thank you in advance!
okay, I was able to connect using memory and this picture:
http://wmpoweruser.com/wp-content/uploads/2008/09/ics.jpg
LOL, now that Ive connected through activesync, I can use my mobiler as my screen is broken!
Need assistance getting USB connection to PC working. (I believe this will be the first step to loading a working ROM since my HD2 is bricked right now.)
Details
1) The HD2 boots to Win Mo 6.5. From there I have been running Android 22 from the SD card. The phone locked a week ago and now when I pull the battery and put it back in, pressing the power button starts to the Pink T-Mobile screen ("stick together") and goes no further - I never see the additional text details in the lower left (radio version and other info, I believe).
2) I have used the Vol up/Vol down/Power botton to do a hard reset. This had no effect on my problem.
3) I can open the Red Green Blue White screen using Vol Down/power button. It shows "Serial" in the white area when USB is not connected. It shows USB in teh white area when the USB cable is connected to a computer.
The red area shows the following 4 lines:
"PB81120 HX-B3"
"SPL-2.08.HSPL 8G XE"
"0x05"
"CotullaHSPL 0x40"
The above leads me to believe that I am still in a position where I can recover from this problem. BUT I can't get either of my 2 computers to connect properly via USB.
I have 2 computers - Win 7 and Win XP.
On my Win 7 - I have installed Drivers so that it no longer warns me that there is a missing USB driver - the most nagging was a Qualcomm driver. I have installed installed Windows Mobile Device Center. When I connect the HD2 to the Win 7 box via USB it WMDC never recognizes my HD2 but I do get the beeps telling me the computer knows a USB device has been attached.
On my Win XP - I have installed ActiveSync. I also have eliminated all messages of missing drivers. ActiveSync also does not recognize the HD2 when plugged in - but again, the computer beeps saying it knows a USB device was connected.
In both cases I have tried the USB connection from both the T-Mo "stick together" screen and from the Red Green Blue White screen and the PC never recognizes the HD2.
-thanks