Do your phones also have the dust behind the touch screen problem? or is it only M88s? within that, is it only my M88? lol
I had to tape up every hole on my phone and just use a bluetooth headset. The dust builds up pretty quickly if there are any open holes and you leave the phone in your pocket. I have opened it and cleaned it 3 times already now (experimented trying to figure out which hole lets dust in). There is a little foam seal around the screen but it just doesn't seem to do the job.
Even right now all taped up there are a few errant pieces of dust annoying the hell out of me. They are hard to notice with the screen on but they still annoy me... You can NEVER get all of them off of there when you take it apart and clean it but you have to try when it gets bad.
Same problem on my M88
I have similar case, how do you can open the front cover?
Thanks
Rodolfo
I have the same problem,
Can you post a video how to do the job cleaner please?
thnak´s
Javier.
Related
Hello,
I have invinsibleshield for my HTC Touch Cruise (full cover) and so far I have been very happy with the protection it provides.
Unfortunately yesterday something strange has happened. When I took out the PDA from my pocket (trousers) I noticed one spot underneath the cover, on the device display. It seems that it is some liquid under the shield. The device itself works fine, so I assume that LDC is not broken.
What could have happened??? There is only one solution - IS absorbed some sweat and transported it below the surface? WOW! Now, the case is how to get rid of it. I tried drying and the spot is much smaller now, but it still exists. Any ideas (except keep your butts dry ) ???
P.S.
Is there any way to make IS not so sticky? On the touchscreen area it's quite frustrating.
Get a pin and pierce a pin-hole where the bubble is (gently, gently, easy does it!). Air or liquid will come out when you press the bubble down after piercing (gently)!
I tried but it doesn't work. It that there is no enough liquid just to get rid of this through the hole.
I hope that the display will not be damaged because of so long contact with my swat. How the hell it is possible that it got inside and cannot be removed/evaporate not!!!
I really don't have a solution for that short of removing the shield. Some shields a repositionable. Check on your shield vendor's website to see what they say about that.
Try placing one of those silicon bead bags on it and leaving it for a while, it should absorb the moisture
I just started developing this odd creaking noise near the bottom and sides of my S4G. Even with a Seidio Active case wrapped around it, the creaking can be felt and heard when hitting the bottom buttons.
The fix is pretty easy. You just need to decrease the amount of movement the back cover has.
I had some .010 mil fiber (fish) paper laying around so I cut a small square that covers the sim card and microsd card area. You can probably use something else, but hey, why not use some insulated paper if you have it.
Lay the paper on top of the area and then slowly place the back cover back on. No holes are in that area above the sim and microsd, so no worries there. You should see an immediate improvement
I needed more than that to stop the creaking/screen movement.
Pathetic we have to go to these lengths
jlevy73 said:
I needed more than that to stop the creaking/screen movement.
Pathetic we have to go to these lengths
Click to expand...
Click to collapse
What did you have to do?
I tried used two squares of paper, but that made the back bulge out a little too much to my liking.
GideonX said:
What did you have to do?
I tried used two squares of paper, but that made the back bulge out a little too much to my liking.
Click to expand...
Click to collapse
I took a post-it and folded it twice. Then placed it on the bottom right area and closed up the cover. For me when I press down on the bottom right side of the screen the whole screen sort of depresses a bit. Only way I could get rid of that was to place the paper in that region. Problem solved.
Post it would have been my backup method
Sent from my HTC Sensation 4G
buy another battery, i recently got an anker also had the creaking problems, noticed the anker is a TINY bit thicker than the stock battery and it removed that problem completely. and that anker battery was DIRT cheap
I just lined the case with some scotch tape. from the bottom to about 3/4 of the way up. I just went around the antenna nubs and the usb hole.
Posted this in another thread, but felt it was valuable here too...
Got the creaking here also, definitely a design flaw. Being obsessive with my devices i couldnt live with it!
I do not recommend putting paper in the cover to fill the gap, as this is just expanding the cover further making it even MORE loose when the paper is not in there. Also i wouldn't recommend it because the paper pushes the back cover out a little more, you may loose a connection for the ground. Which is the little metal springy thing, half way up the right hand side. Obviously its not a good idea to 'push' the cover further away from this ground spot. I have heard that people have had issues with screen responsiveness due to a static build up from not grounding properly.
What i did to fix this problem was a bit of a kitbash of sorts.
Mine was creaking on the bottom right area, like most. The problem is there is too much play between the little black catches on the battery cover and the latch on the handset. Instead of filling up the gap between the phone and the cover (Ala paper, card in the cover) I closed it!
What you need to do is get some very thin plastic film. Like that on kids toy packaging etc. Not the thicker stuff though. This stuff would be under 1mm thick. It came as a viewing window in the box my new wallet came in. So you can sorta imagine what im talking about.
I cut a piece about 10mm long and as wide as one of the two little black catches. I applied a VERY thin coat of super glue to one end of the film. Just enough to cover the area under the catch. Then i carefully placed the film with the superglue on it under the catch, and then quickly applied some pressure to it with some tweezers. Then i carefully cut the excess off with a pair of finely tipped nail scissors.
The result is that it now PULLS the screen/phone INTO the cover more by making the little black catch thicker. Not the opposite (paper method), which pushes the cover out, creating a further problem of adding more paper under the cover over time as the cover expands/loosens to compensate. Not to mention a possible grounding loss and resulting damage.
Hope this helps some people that have had multiple replacements or could not be bothered replacing for such a cosmetic issue. (Like me). It definitely works, just got to get your surgeon on and be accurate with your placement of the film.
Apply this to what ever side creaks the most, and bam its gone. Nice. Solid phone... again.
If anyone wants more specific details etc, im all ears.
Regards,
Matt.
will try it with an double side film ...
i mean a film that hold back cover and phone together ;-) i think doing paper in there will do damage with time
I contacted HTC and they sent me another/new one. No more creaking!
RaptorRVL said:
I contacted HTC and they sent me another/new one. No more creaking!
Click to expand...
Click to collapse
Back cover or whole phone?
I have the same problem too. And it just seems to get more and more "cracking"
Hi xda, so I got tired of having dust under my screen and decided to try to fix this myself, I used many disassembly videos and this http://forum.xda-developers.com/showthread.php?t=1479734&highlight=dust as guides, initially I didnt open my phone completely, and used a hair dryer to heat and loose the glue, I guess that wasnt enough, then I finally separated the glass from the screen and procedeed the cleaning, everything good.
Then when I pushed the glass and realized there was a little space between the glass/lcd and the plastic frame (look at pic), tried to put the back cover in again and noticed the right side of the phone, the plastic one was kinda lifted and barely fitted my back cover again, reopened and realized this (look at pic) it seems that the main frame and plastic frame (pic again) got a bit separated, when I was trying to lift the glass i heard some cracks there, I tried pushing it gently but I dont want to damage the lcd, next thing im gonna do is disassemble it completely and hit gently the lifted side of the frame with a hammer so it fits flush again, before doing this, Do you have any sugestion or advice? Has this happened to you?
Also since I dont have a proper heat gun and I'll be using a hair dryer I would thank you if you know and can tell me what areas of the lcd are glued to the main frame, pic attached, if you know you could use paint to point them.
Im a bit worried about the tension the phone is getting with the cover on, I hope only the main frame is getting it... as the phone is pushed to its side (0.5-1mm maybe) I cant plug my headphones and i get slightly worse overall signal. Thank you in advance for any help.
Dom42 said:
Hi xda, so I got tired of having dust under my screen and decided to try to fix this myself, I used many disassembly videos and this http://forum.xda-developers.com/showthread.php?t=1479734&highlight=dust as guides, initially I didnt open my phone completely, and used a hair dryer to heat and loose the glue, I guess that wasnt enough, then I finally separated the glass from the screen and procedeed the cleaning, everything good.
Then when I pushed the glass and realized there was a little space between the glass/lcd and the plastic frame (look at pic), tried to put the back cover in again and noticed the right side of the phone, the plastic one was kinda lifted and barely fitted my back cover again, reopened and realized this (look at pic) it seems that the main frame and plastic frame (pic again) got a bit separated, when I was trying to lift the glass i heard some cracks there, I tried pushing it gently but I dont want to damage the lcd, next thing im gonna do is disassemble it completely and hit gently the lifted side of the frame with a hammer so it fits flush again, before doing this, Do you have any sugestion or advice? Has this happened to you?
Also since I dont have a proper heat gun and I'll be using a hair dryer I would thank you if you know and can tell me what areas of the lcd are glued to the main frame, pic attached, if you know you could use paint to point them.
Im a bit worried about the tension the phone is getting with the cover on, I hope only the main frame is getting it... as the phone is pushed to its side (0.5-1mm maybe) I cant plug my headphones and i get slightly worse overall signal. Thank you in advance for any help.
Click to expand...
Click to collapse
I wanted to try it myself, but didn't have the guts. Sorry to hear your problem.
The guide said "5. Clean off all the crappy double sided tape from the factory."
It seems to me that you have put the same double tape. I suggest you remove the LCD again, clean the old tape and apply a new one.
Good Luck!
Edit: Does your touchscreen work well?
elvisypi said:
I wanted to try it myself, but didn't have the guts. Sorry to hear your problem.
The guide said "5. Clean off all the crappy double sided tape from the factory."
It seems to me that you have put the same double tape. I suggest you remove the LCD again, clean the old tape and apply a new one.
Good Luck!
Edit: Does your touchscreen work well?
Click to expand...
Click to collapse
Dont be afraid of trying, i was also scared at first but bah, 1. There's no official htc support in my country 2. I dont trust repair houses. 3 I wont wait 2-4 weeks for something relatively easy. So why dont try by yourself?
"Clean off all the crappy double sided tape from the factory" I dont have double sided tape at hand right now, getting it in 2 days, however thats not the problem, the glass sits flush and tight even with the old tape, the problem is that as i said my phone somehow got wider and the back cover is hard to put. Thanks, im gonna need good luck.
Oh and yes my touchscreen works perfectly.
Dom42 said:
Dont be afraid of trying, i was also scared at first but bah, 1. There's no official htc support in my country 2. I dont trust repair houses. 3 I wont wait 2-4 weeks for something relatively easy. So why dont try by yourself?
"Clean off all the crappy double sided tape from the factory" I dont have double sided tape at hand right now, getting it in 2 days, however thats not the problem, the glass sits flush and tight even with the old tape, the problem is that as i said my phone somehow got wider and the back cover is hard to put. Thanks, im gonna need good luck.
Oh and yes my touchscreen works perfectly.
Click to expand...
Click to collapse
There's no HTC support in my county either. Maybe it got wider because of the heat. Even though the glass sits tight I suggest you change the old tape, cause that's what let dust in the first place. The guide said also smth about silicon, did you apply it?
Was it difficult to remove the LCD with the hairdryer? I don't have a heatgun.
LOL, seems I'm the one doing the questions now.
elvisypi said:
There's no HTC support in my county either. Maybe it got wider because of the heat. Even though the glass sits tight I suggest you change the old tape, cause that's what let dust in the first place. The guide said also smth about silicon, did you apply it?
Was it difficult to remove the LCD with the hairdryer? I don't have a heatgun.
LOL, seems I'm the one doing the questions now.
Click to expand...
Click to collapse
No it didnt got wider because of the heat, when i was trying to open it i forced the bezel/metal main frame (4th pic) so it unclipped. Getting the double tape tomorrow. No way im gonna put silicon, ill put just 4 tiny squares of doublesided tape, i would rather clean it monthly than that, also i keep it always clean, it just had the dust before (second hand).
Yes, it was very difficult to remove the LCD, dont even try this without a heatgun, i was lucky to not mess something else duh i even crushed the LCD cable a bit, but it works normally. Only solution now is to get a new main frame.
Dom42 said:
No it didnt got wider because of the heat, when i was trying to open it i forced the bezel/metal main frame (4th pic) so it unclipped. Getting the double tape tomorrow. No way im gonna put silicon, ill put just 4 tiny squares of doublesided tape, i would rather clean it monthly than that, also i keep it always clean, it just had the dust before (second hand).
Yes, it was very difficult to remove the LCD, dont even try this without a heatgun, i was lucky to not mess something else duh i even crushed the LCD cable a bit, but it works normally. Only solution now is to get a new main frame.
Click to expand...
Click to collapse
Thanks for the advice. I hope you manage to fix your phone
I've noticed a lot of dust accumulating around my case and the sides of my phone after i take it off, the dust seems to be stuck inside of the sides of the screen and inside of the speakers. Is this going to be a problem?
huntaz556 said:
I've noticed a lot of dust accumulating around my case and the sides of my phone after i take it off, the dust seems to be stuck inside of the sides of the screen and inside of the speakers. Is this going to be a problem?
Click to expand...
Click to collapse
Short answer, no.
Clean out your pockets.
Sent from The Deathstar
Some canned air usually does the trick - some cases attract more lint and dust than others, but keeping pockets clean never hurts =P
Alright, thank you. I just wanted to make sure my phone was okay
Well after a few minutes cleaning the top speaker grill lightly with a tooth brush, anti-bacterial / disinfectant i was shocked that the thing just fell off
iStasis said:
Well after a few minutes cleaning the top speaker grill lightly with a tooth brush, anti-bacterial / disinfectant wipe i was shocked that the thing just fell off
Click to expand...
Click to collapse
Does anyone know if this would be fixed under warranty and if not the best way to restick it down?
I would try heating up the glue and sticking it back down.. heat gun would be best.. just be careful of how much you heat it up. Also.. in the future I wouldn't use a toothbrush. You maybe pushing dirt down into the grill. Something like silly putty might work better. I meant to add that when I get mine, I'm going to try a car/electronics attachment that came with my shark vacuum. It has tiny hose parts that might be able to suck debris out of the grill instead of pushing it down in there. I think they sell attachments like that for small shop vacs and other vacuums but I'm not sure.
DOTC said:
I would try heating up the glue and sticking it back down.. heat gun would be best.. just be careful of how much you heat it up. Also.. in the future I wouldn't use a toothbrush. You maybe pushing dirt down into the grill. Something like silly putty might work better.
Click to expand...
Click to collapse
Thanks for the tip the 1st few times i used a softish toothbrush and was ok, silly putty ive seen aimed for tech stuff and more jel like would work better i think next time and had used the tooth brush before ok i just think i removed the adhesive bond when cleaning it with the wipes as the phones not been expose to any heat for it to warm up enough for the grill to slide off.
Fingers cross Razer would good will a return / repair for me as now the speaker is a bit tinny and while holding the plastic tightly to the phone its not great abover 70% volume level but looking at the speaker grill in the middle its torn away a patch. This maybe to allow the sound out as it was a neat cut in the material thats left. Still wouldnt want to superglue resin (self repair) it until razer come back and say if they will fix it for me or not.
https://www.amazon.com/Scotch-Adhesive-Transfer-Tape-Clear/dp/B00HD27UJC
This stuff would be good.
Cheers i did compile a post and closed the wrong tab went away from my desk. Im waiting for someone in Razer to agree to the repair under warranty but if not ill be getting some tape hopefully i can find some thin and strong enough to go between the plastic thats come off and the non sticky adhevsive tape thats still there. Im not 100% sure if i should tape around the little square cut out or not. i was thinking small path between the left edge and camera/sensor and then a small bit to e right between camera and the torn away patch and then the last strip to the right of the pacth. its odd the patch is thereand its alot thiner than the rest of it.
Applying some pressure to the patch part i can only assume its the speaker as when covering it up the phones quiter. just unsure why its a patch? when playing last night with the bit that fell off theres some vibration so thinking where the patch is i just secure it down with the tape where i can.
Also may get a screen protector to remove the lip between the screen height compared to the plastic that fell off as this is not smooth and is a little sharp. - I may flag this with razer as a design flaw which could have lead to the problem as if it was sunken down it wouldnt have moved out of place
Something like this almost seems better. https://www.amazon.com/Innovative-C...&sr=8-4&keywords=cleaning+gel#customerReviews