Related
Ok, i've had a problem with it, first i removed the protector that was as large as the device and made the screen very ugly, then i got the one from the box and putted it on, every air-bulb was gone when i kept rubbing etc.
1 stayed, under that bulb there was something white, i found out it was a 'piece' of dust.
It was kind of annoying so i removed the screen-protector, now when im trying to put it on i get lots of 'dust-bubbles',
Anyone has an idea of how to do it or should i just leave my diamond without the screen protector?
Protection
Personally i prefer to have a screenprotecter on my device. I can recommend invisible shield. its very durable and will not be scratched. check it out on www.zagg.com
If you remove the protector, then there will alway be dust next time, because the dust get stuck to the protector glue. (I have also remove mine several times)
I have tried zagg, but I can't recommend it. It is a little sticky (which they also says on their homepage) and I don't like that. The floating feeling is gone. It is also not that invisible.
I have selected to buy a new original protector, and will use that.
The trick to get it on without bobbles is to start on the long edge and then slowly add it. (Keep the 'paper' on as long a possible).
(Michael
willyy1991 said:
Ok, i've had a problem with it, first i removed the protector that was as large as the device and made the screen very ugly, then i got the one from the box and putted it on, every air-bulb was gone when i kept rubbing etc.
1 stayed, under that bulb there was something white, i found out it was a 'piece' of dust.
It was kind of annoying so i removed the screen-protector, now when im trying to put it on i get lots of 'dust-bubbles',
Anyone has an idea of how to do it or should i just leave my diamond without the screen protector?
Click to expand...
Click to collapse
The original is washable. Wash it and dry it with a paper towel that sucks in the water bubbles, wipe dry and clean your screen and reapply it.
By the way, this goes to Accessories forum.
mhfalken said:
If you remove the protector, then there will alway be dust next time, because the dust get stuck to the protector glue. (I have also remove mine several times)
I have tried zagg, but I can't recommend it. It is a little sticky (which they also says on their homepage) and I don't like that. The floating feeling is gone. It is also not that invisible.
I have selected to buy a new original protector, and will use that.
The trick to get it on without bobbles is to start on the long edge and then slowly add it. (Keep the 'paper' on as long a possible).
(Michael
Click to expand...
Click to collapse
Where can you buy a new one, i need it really fast because my phone is without protection right now and no i am affraid of pressing it to hard to leave a permanent mark..
tnyynt said:
The original is washable. Wash it and dry it with a paper towel that sucks in the water bubbles, wipe dry and clean your screen and reapply it.
By the way, this goes to Accessories forum.
Click to expand...
Click to collapse
I did this and the dust keeps coming at the protector and my phone and there will be bubles because the dust gives it a 'height-problem'..
I bought invisible shield for mine, its pretty nice after say 4 days from install.
For first 2 days it might seem really bad but it gets much better.
I somehow scratched it without even noticing it, so I sent picture to zagg and they sent me new one. Even though scratch was very minor.
mhf
hi. this my first post on this web site
excuse me for my bad english
i have a diamond and i remove orginal screen protecter because i write sms with letter recorgnizer and the area that i write words on the screen become white and scratch. i remove orginal and buy a new one that for iphone. i cut it for my phone size and apply it. its sooo much stiky and i have a problem like orginal one.i wnat to remove it and when i do it a tiny layer of glue stand on my diamond screen. i can't clean it. and it give a bad scene to my diamond.
what's your idea. i give u a pichture from my diamond screen.
Perhaps you could use isopropyl alcohol, usually it will remove glue without damaging the plastics surface (in that case: your display). DON'T USE nail polish remover, acetone or even benzine, it will remove the glue too - but your display would look "milky". You can get isopropyl alcohol at the pharmacy.
Tell us if that helped you
mhf said:
hi. this my first post on this web site
excuse me for my bad english
i have a diamond and i remove orginal screen protecter because i write sms with letter recorgnizer and the area that i write words on the screen become white and scratch. i remove orginal and buy a new one that for iphone. i cut it for my phone size and apply it. its sooo much stiky and i have a problem like orginal one.i wnat to remove it and when i do it a tiny layer of glue stand on my diamond screen. i can't clean it. and it give a bad scene to my diamond.
what's your idea. i give u a pichture from my diamond screen.
Click to expand...
Click to collapse
You might be interested in this thread: http://forum.xda-developers.com/showthread.php?t=421229
I didn't get a screen protector with mine... I mean, I had a shipment protector with a little tab for peeling off, but nothing came with it for long term use. It's a Sprint, did they just not include one?
the exim screen protector is very good and smooth
I always use the Brando screenprotectors. See their online shop. They ship worldwide for only $ 3,00 shippingcosts.
It is very easy to install, easy to clean, 100% garanteed scratch free and very durable.
iixnullxii said:
I didn't get a screen protector with mine... I mean, I had a shipment protector with a little tab for peeling off, but nothing came with it for long term use. It's a Sprint, did they just not include one?
Click to expand...
Click to collapse
I've got a Sprint Diamond too, and didn't think I got a protector either, but it was in the separate bag that has the manuals. It should have come with one...Wish it woulda come with an extra one too, oh well.
I had the same problem with misalignment and dust bubbles with the HTC protector on my first few tries...i did however fix the problem...
Take the protector off and clean off the phone...use a microfiber cloth to get all the dust and oil off...after its super clean...take the protector and wash it off with some mild soap...rub the soap in with your fingers and get it clean. Be sure to note which side is down. After its clean, hold it around the edges and let the water bead off...i blew on the protector to get residual water off...some water is ok...actually helps with the install...the basically carefully apply it still holding the sides making sure not to leave finger prints. Start from the top and work your way down... i used a credit card pushed against the microfiber cloth to squeegie the protector down...be carefull with the few drops of water. After you have it down...there might be little bubbles or what looks like water spots where water is trapped under the screen...dont worry...just use your phone and leave it alone. Once it heats up from the excessive phone use it will start to dry up and the protector will come out very nice and smooth. Mine is flawless and i did the wash with soap apply and remove at least 3 or 4 times to get it right...Just be patient
I use screen protector from martinfields, what do you say about, anyone have one??
I think the best in market
My HTC one got a nasty scratch in it last week, so I ordered a Martin Fields.
It arrived this morning and I've got it on without any problems. So far I've noticed:
- It's not a perfect fit like the HTC one was. The hole for the speaker at the top is larger than the hole in the phone. It's not bad though.
- The visibility of the screen does seem better than the HTC protector, but I don't know if it's just the placebo effect of having a more expensive protector.
- It was _easy_ to put on, no bubbles at all
- The protector for the bottom buttons is awful. The circle is just the right size to completely hinder using the touch wheel and it's obvious that you've got a piece of plastic on there.
- It seems smoother than the original HTC one when using the stylus.
So far I'm impressed with it. I didn't bother with the camera hole or bottom hard buttons. The in box HTC one was fine for me, but when I got a scratch on it (my stylus somehow developed a sharp edge), it annoyed me.
I'm using the one supplied as standard with a uk CompactIV and it's great- you can hardly tell it's thereand the sensitivity seems fine.
I have 24 diamond screen protectors. Because i bought 24 diamonds and sold them all without screen protectors so i am sorted untill i buy another phone.
After using the martin fields one for a couple of days, I think it's great.
The screen looks much brighter and clearer through it (I thought the HTC one was great, but I do notice the difference). Plus the smoothness is brilliant, theres pretty much no friction for the stylus or fingers
where can i purchase the htc screen protector? the original that comes in the box...
Just thought I would warn others that after only a week of owning my cool TP I noticed a scratch on the screen and button area. A very straight score down the middle. Lucky I had my screen protector fitted else I would have been very upset.
Replaced the protector a week ago and today noticed a similar score down the screen though less deep. I then realised that this was due to a piece of grit in my pocket that had slipped between the case and the screen and scratched it as I pulled it out of the case.
I have now ordered a proper fully closed case to give full protection and hope this is a warning to others!
Definitely invest in a screen protector, they don't spoil the look of the device or impede it's usability in any way, they are easy to apply and could save you a lot of tears! Then use a decent case!
am using martin fields protectors.... it is tough enough that when i dropped my phone on the stairs, the rest of the body is scratched except the screen area and hkey areas where it is protected.
i frequently use my fingernails too. i don't trust other screen protectors... used it for my previous Axim v51 and X500 ... device gave out before the protectors.. meh.
alpha01 said:
am using martin fields protectors.... it is tough enough that when i dropped my phone on the stairs, the rest of the body is scratched except the screen area and hkey areas where it is protected.
i frequently use my fingernails too. i don't trust other screen protectors... used it for my previous Axim v51 and X500 ... device gave out before the protectors.. meh.
Click to expand...
Click to collapse
Yes I was definitely satisfied with the Martin Fields solution, which I've reviewed on my Diamond. Will order one for my new TP as well.
The review is in Hebrew and was published here (with some photos)..
http://www.pocketpcfreak.com/archive/00007709.htm
=====
Saar
I saw someone scratch the screen protector on their Touch Pro right in front of me, he had just put the screen protector on it and put it into his case, it was one of those that holds it right on your hip... Took it back out, exactly what you're talking about, a nice line right across the screen.
If using the case provided, the ribbon inside is attached so that you can insert the phone from both ends. If you feel inside, one side will be folded over and therefore sticks out quite abit which feels quite abraisive, whilst the other side of the case is much smoother because the ribbon is not folded. Inserting the phone from the other side, reverses which side sticks out more. I ensure that the screen side is always slid in with the smooth side facing the screen. So far, this has been ok.......................
I have just got hold of the HTC Touch Standard belt pouch (PN: PO S322) and it fits perfectly with a standard belt clip.
Velcro so the Sliding magnetic keyboard sensor does not go T^Ts up!!
anyone know where i can get extra protectors for my tp?
Personally, I always keep my TP in my pocket, without a case. The only time I ever use a case is if I'm putting the phone into a bag or box with other gear which might scratch it. Also, I never put keys etc into the same pocket as the TP, only a handkerchief. I've kept phones this way for many years and never got a single scratch on my screen. The inside of your pocket is generally a nice soft place for your phone. Case not necessary! In fact, all the case does is muffle the speaker and make it harder for you to hear the phone ringing.
In fact, until I got my TP I never even used screen protectors. The only reason I'm using one now is because it came in the box!
auriken said:
anyone know where i can get extra protectors for my tp?
Click to expand...
Click to collapse
Where are you based?
ardsar said:
If using the case provided, the ribbon inside is attached so that you can insert the phone from both ends. If you feel inside, one side will be folded over and therefore sticks out quite abit which feels quite abraisive, whilst the other side of the case is much smoother because the ribbon is not folded. Inserting the phone from the other side, reverses which side sticks out more. I ensure that the screen side is always slid in with the smooth side facing the screen. So far, this has been ok.......................
Click to expand...
Click to collapse
I haven't noticed the difference in the sides. I have been using this case for about a month and haven't seen any signs of scratching to the screen (although I have a screen protector on) or any other part.
auriken said:
anyone know where i can get extra protectors for my tp?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=428279
ardsar said:
If using the case provided, the ribbon inside is attached so that you can insert the phone from both ends. If you feel inside, one side will be folded over and therefore sticks out quite abit which feels quite abraisive, whilst the other side of the case is much smoother because the ribbon is not folded. Inserting the phone from the other side, reverses which side sticks out more. I ensure that the screen side is always slid in with the smooth side facing the screen. So far, this has been ok.......................
Click to expand...
Click to collapse
I agree with you. I always feel where the smooth side is and make sure that its the one facing the screen when I'm sliding my TP inside the leather case. So far I never had any scratches on mine.
I have noticed a small cut in my plastic (I haven´t taken of the large piece of plastic that came on then phone). From the middle of the screen and down to the edge.
I don´t get it! That folded ribbon ain´t sharp, it´s just wide, how the heck can it leave a cut like a scalpel? The other smooth side has a sharp thing in the seam, that could possibly cut but I really don´t think so.
I´m scared now, because there is a cut but nothing in the pouch can cut!
I just ordered one of these and recived it today.
Top pouch tbh
ebay
Item number: 270278860452
Mr.Sir said:
I have noticed a small cut in my plastic (I haven´t taken of the large piece of plastic that came on then phone). From the middle of the screen and down to the edge.
I don´t get it! That folded ribbon ain´t sharp, it´s just wide, how the heck can it leave a cut like a scalpel? The other smooth side has a sharp thing in the seam, that could possibly cut but I really don´t think so.
I´m scared now, because there is a cut but nothing in the pouch can cut!
Click to expand...
Click to collapse
Exactly!! Same happened to me. A very straight deep cut, saved only by the screen protector. I could only assume that a piece of grit got trapped between the sleeve and the phone. This wouldn't happen in an ordinary case, the pouch fits very tightly against the screen and this is where the danger lies. I have stopped using it.
Do your phones also have the dust behind the touch screen problem? or is it only M88s? within that, is it only my M88? lol
I had to tape up every hole on my phone and just use a bluetooth headset. The dust builds up pretty quickly if there are any open holes and you leave the phone in your pocket. I have opened it and cleaned it 3 times already now (experimented trying to figure out which hole lets dust in). There is a little foam seal around the screen but it just doesn't seem to do the job.
Even right now all taped up there are a few errant pieces of dust annoying the hell out of me. They are hard to notice with the screen on but they still annoy me... You can NEVER get all of them off of there when you take it apart and clean it but you have to try when it gets bad.
Same problem on my M88
I have similar case, how do you can open the front cover?
Thanks
Rodolfo
I have the same problem,
Can you post a video how to do the job cleaner please?
thnak´s
Javier.
Ran across this today searching for cases for the Epic. Anyone using one? Its interesting in that it locks the slider during normal use and hinges open if you want to use the keyboard.
http://www.pdair.com/catalog/product_info.php?cPath=10100000_10000000_11001061&products_id=31414
Now this looks like quite a nice case for functionality.
Now if they just took off the whole part in the back for the clip and form fit the corners a bit more and offered it in more colors that'd be nice.
This may be the best thing I can do for now, I have been scouring for a jelly case to slip over the epic, since I never use the keyboard
Now, if somebody has the ability to cleanly cut aluminum and wants to sell a matched set consisting of this case with a hole cut in the back for the hump on the extended battery the other guy is selling to poke through... (strokes credit card and sighs)
It's hard to tell from the pics... does the case snap onto the lower half, or does the phone just rest inside?
How firmly does it secure the phone when the case is closed? Does the power button still cause the two halves to separate a little, or are both held firmly in place from both sides?
bitbang3r said:
Now, if somebody has the ability to cleanly cut aluminum and wants to sell a matched set consisting of this case with a hole cut in the back for the hump on the extended battery the other guy is selling to poke through... (strokes credit card and sighs)
It's hard to tell from the pics... does the case snap onto the lower half, or does the phone just rest inside?
How firmly does it secure the phone when the case is closed? Does the power button still cause the two halves to separate a little, or are both held firmly in place from both sides?
Click to expand...
Click to collapse
There are videos on you tube. The bottom looks like a very snug press fit. Top must be looser to allow for the hinge to work.
Sent from my SPH-D700 using Tapatalk
...
I had a similar case for my old HTC Titan. I LOVED it. Being a pretty serious phone abuser, that case kept my phone together!
-Rob
I used to have a similar case for my Treo and they are extremely well made. I irregularly dropped my phone from about 5 feet in the air onto hard linoleum and it never suffered any indignities. These come in both black and silver so if you want a different color you would want the silver so you could send it out to be powder coated.
I just ordered one.
Mine came last night.
The good: locks the slider firmly closed. No wobble or "play" at all when pressing the power button. Phone easy to remove (for GameGripper purposes).
The bad: Feels terrifyingly slippery compared to the Seidio ActiveX. Obstructs "slide down" gesture for notifications.
The seemingly fatal (a big one): my "back" fake hardkey keeps randomly going berserk... but ONLY that specific one. The foam in the top half seems to be confusing the capacitive sensor.
Sent from my SPH-D700 using XDA App
Update: I've had the 'search' fake hardkey freak out a few times on me, too.
Another problem: it's definitely affecting reception. 4G and GPS barely work with the case in place.
Sigh. So close. So agonizingly close. It's awesome to not have the phone shear and jiggle apart every time I hit the power button, and the fact that it allows the phone to be easily removed for the Game Gripper without really compromising the slide-out keyboard's usability is very cool.
I'm really convinced that this case went straight from plastic prototype to mass production before anyone actually tried to use it in an area with 4G service, high humidity (presumably what's screwing up the foam and touchscreen), and who didn't just assume that the GPS was dysfunctional because Samsung sucks.
Sigh. Too expensive to throw away, and really nice in ways that ultimately don't matter because the touchscreen-button problem makes it totally unusable
The plot thickens: more touchscreen observations:
* Oddly, there's NO FOAM around the lower part of the screen where the phantom-pressed fake hardkeys are.
* Last night, it went completely berserk with phantom button presses on cue when I rubbed the latch a certain way.
This suggests that the problem's root cause might extend to the electrical conductivity of the case itself. It's strange, because I wasn't able to find reports of the same problem for users of Monaco cases for other phones (like the Droid). Lots of complaints about signal attenuation, but no reports of touchscreen problems.
I'm seriously tempted to buy some liquid electrical tape and coat the inside of the lid to see whether it helps. The problem DOES seem to go away when the lid is no longer in contact with the screen. However, if it's happening because the sensor is acting kind of like a Hall Effect sensor and the case is acting like a Faraday cage, nothing short of making the case (or at least the top lid) out of plastic is likely to fix the problem. Still, it's worth a try since I really like the case itself, and my alternative is to basically chuck it.
Update: as an experiment, I wrapped black electrical tape around the bottom lip of the top part. It helped a lot. I think I might have also found a contributing cause: cat fur. I think wisps of cat fur might be bridging the metal case & screen and carrying static electricity to the sensor. Oddly, though, some of its *worst* back-arrow spasams have occurred with the phone laying on the desk, untouched, 3 feet away.
I'm still trying to think of a good way to plastic-coat the case without making it look bad & get a nice, even black rubbery coating on it.
Sent from my SPH-D700 using XDA App
How thin is it compared to the other plastic cases?
Very interested in getting the Monaco Aluminum Case, which is very similar to this one. My last concern, how thin is it compared to Seidio Innocase Surface?
I'm going to receive my HTC One soon, and I ordered a screen protector for it that requires the use of a liquid solution while applying (Kind of like Invisible Shield). I'm worried, however, that a little bit of the liquid may go into my speakers and mess them up. Is there a chance this will happen? You can't pull out the battery of the One, so I'm afraid some electricity will be flowing and the speakers will get messed up.
Sewrizer said:
Nothing to worry about, apply that liquid only on the screen, apply the screen protector over it then with a credit card or something similar shaped press on the bubbles and sweep in the opposite direction of the speaker (so that the liquid won't get beneath). they recommend using a liquid because liquids they are incompressible(thus, being able to remove the bubbles) so you can pretty much use water instead of that. you don't have to use the liquid, but if you apply the screen protector without a layer of water, you won't be able to get rid of some of the bubbles.
A few physics to explain, you don't need to read this.
In presence of water, between the screen and the protection, will develop cohesion which will make it really hard to remove the screen protector. (the example of cohesion is in laboratories, where scientists put a liquid between those very thin pieces of glass and analyse it at the microscope. it is impossible to pull one piece of glass off the other one due to that force, the only way they do this is by sliding)
hope i helped
Click to expand...
Click to collapse
Thanks. If, by any chance, some of the liquid leaks a bit into the ear piece, will that affect the phone?