Database Info

P3600 Full Body InvisibleShield finally available

Figures they'd come out with it a week before I'm thinking of picking up an Imate Ultimate 8150. But it's out for those of you interested link below.
P3600 Full Body Invisible Shield
http://www.shieldzone.com/item_description/HTCP3600I.html

Nice!! It's listed for the P3600i, but I guess it's exactly the same as the P3600.
Anybody tried it already?? Better than a regular silicon cover?

How does this work?
If it is stretched all over the PDA, how is it joined/sealed? What about removing the batter cover or using the thumb wheel? Is it fixed like cling-film?
Also, the screen is recessed from the surround so if it is stretched around the housing and screen, then there would seem to be a gap between the screen and this cover, so what will the sensitivity of the screen be like?

PaulusUK said:
How does this work?
If it is stretched all over the PDA, how is it joined/sealed? What about removing the batter cover or using the thumb wheel? Is it fixed like cling-film?
Also, the screen is recessed from the surround so if it is stretched around the housing and screen, then there would seem to be a gap between the screen and this cover, so what will the sensitivity of the screen be like?
Click to expand...
Click to collapse
If you followed the link and watched the installation video showing it being applied to an ipod you wouldn't have asked.........suggest you try that first.

Andych said:
If you followed the link and watched the installation video showing it being applied to an ipod you wouldn't have asked.........suggest you try that first.
Click to expand...
Click to collapse
looks like it would be a least 3 pieces - one for the screen, then one for the keys, and one for the back - which does not protect the sides. And the video doesn't show how it fits on the phone, it shows how it fits on the front of a ipod - so don't be a smart a*s. He was asking how it fits on this phone not an ipod dumb a*s.

earl00 said:
looks like it would be a least 3 pieces - one for the screen, then one for the keys, and one for the back - which does not protect the sides. And the video doesn't show how it fits on the phone, it shows how it fits on the front of a ipod - so don't be a smart a*s. He was asking how it fits on this phone not an ipod dumb a*s.
Click to expand...
Click to collapse
Get life....yes the clip shows it being fitted to an ipod......if you gothered to watch the clip you would have seen that the piece for the back also does the sides as they wrap around.....apart from the size etc the actual method of applying this will be the same.
Next time smart a*s do your homework rather than mouthing off.

Oh yes all my questions answered if only I had watched the ipod video.
Now All I need is an m700 that is exactly the same shape as an ipod, with all the buttons in the same place, with a flush screen, and well, all very ipodish, and then it will all be clear.
So this will be no more than a screen protector on the PDA. It will not protect the buttons or lower raised section of the housing. Also won't protect the sides (too many buttons), and it seems that the tight curves will be a problem for this cover. I can see this peeling off the m700 in a very short time
If you know so much about it, then can you explain how it will work with a recessed screen? Will I be able to tap it all over with a key and not damage the phone, and if I throw it in a box of coins, will all the phone be safe from scratches and chips - just like the ipod?

PaulusUK said:
Oh yes all my questions answered if only I had watched the ipod video.
Now All I need is an m700 that is exactly the same shape as an ipod, with all the buttons in the same place, with a flush screen, and well, all very ipodish, and then it will all be clear.
So this will be no more than a screen protector on the PDA. It will not protect the buttons or lower raised section of the housing. Also won't protect the sides (too many buttons), and it seems that the tight curves will be a problem for this cover. I can see this peeling off the m700 in a very short time
If you know so much about it, then can you explain how it will work with a recessed screen? Will I be able to tap it all over with a key and not damage the phone, and if I throw it in a box of coins, will all the phone be safe from scratches and chips - just like the ipod?
Click to expand...
Click to collapse
Lets get this straight....I haven't used this product...however when I saw the "link" I went to the manufacturers site to get a better understanding of it....
I watched the video and while it was of it being fitted to an ipod I got a basic understanding of how it could be fitted to a P3600i.
I didn't think it was "cling wrap", I understood that there would be several sections involved....including one for the recessed screen (yes, just like a normal screen protector) and I too would be skeptical of it protecting all parts of the phone.
There is a tendency in these forums for people to not search out information but to ask seemingly dumb questions.....
As this product is new for this model....why not just ask if anyone has tried it or ask the manufacturer for more information.....or is that too hard to do????

NOT FULL BODY...JUST SCREEN ONLY

The site says full body not Screen only, that's a separate option...
I would really like to know if and how exactly this works on 3600.
I actually have silicon case and screen protector for mine, but this would make it considerably smaller...

Bought and use the InvisibleShield
Folks,
I bought it and had it send to Holland. Took about 1 to 2 weeks but ok I am not in a hurry.
The full body covers basically all the shiny black plastic plus the screen. The rest (middles of the sides and the front keys) are not covered. Also offcourse the camera, speakers etc are not covered. However, and this is probably the difference between P3600 and P3600i the front camara is covered by the shield blurring the image. Now I have already put it on the camera but the next time I would use a hole puncher to add the extra hole. I probably will use a sharp hobby knife to cut an extra hole (on the other hand I never use video conferencing).
The plastic is more stronger and thicker then normal screen protectors. Haven't tried to scratch it on pupose and guess what I am not going to do it. If a scratch forms by accident I will mention it here.
The screen takes some getting used to with the new cover. The plastic does not "slide" as easy as the original screen protector or the screen itself. Maybe this is just in the first period.
The application process it pretty easy if you just take the time. Takes about 30 minutes if you do it slowly. Only 2 minor bubbles on the back but those are not really an issue, the rest is perfect.
Hey for 20 euro's I think it is a good deal. No horrible rubber case or GPS blocking metal case for me anymore. Only downside is that if the phone is dropped now there is no protection. This is only against scratches.
Lifetime guarantee so lets see how often I have to send it back.
All in all recommended so far (but that is just after 1 day of use)

I want to see it
Post a picture please

Isn't it invisible?..

See the invisible sheet
Well actually it is quit difficult to see but here are some picures. The picture from the side shows you some edges.

Edges
The edges that you can see in the pic don't seem to line up perfectly, how were the dimensions on the rest of the edges?
i've been thinkin of getting one of these since i saw them for ipods but that messy edge is scaring me away a little, also how are you finding the screen protector after a little more use?

Edges reply
Well the edges are more because of my talent I think. The reason why I showed you this is because at least you can see something. For the rest it alligns perfectly.
After using it for a while it still seems a great product. I accidentaly dropped the thing but no scratch at all. What you do notice is the slightly more pressure you need when using the stylo. Also the screen protector is not as smooth as the original screen making the sliding a little more difficult. Also the plastic sticks to your ear while calling. But all in all still recommended.

I just put it onto the white one...
...and it is invisible. You can see it only on buttons' silver surrounding, on white parts only the edges are visible if you try really hard. I haven't got a good enough camera to show it, sorry.
It has a sticky feeling about it (maybe needs to dry more?). I don't like it on the screen - feels sticky and thick. I'd say use a decent screen protector instead.
It came WITH the cut-out for a camera (it's 3600i shield, I've got 3600), so it fits like a glove.
Oh, it's not a stress-free, low pressure 15 minutes application like they advertise it. It's fekkin pain in the ar$e one hour job, you're swetting your ar$e off. And - I guess - you can never get it perfect at the end. There will always be a bubble or misaligned edge somewhere (or is it me?).
Long term use review to follow.

sabestian said:
...and it is invisible. You can see it only on buttons' silver surrounding, on white parts only the edges are visible if you try really hard. I haven't got a good enough camera to show it, sorry.
It has a sticky feeling about it (maybe needs to dry more?). I don't like it on the screen - feels sticky and thick. I'd say use a decent screen protector instead.
It came WITH the cut-out for a camera (it's 3600i shield, I've got 3600), so it fits like a glove.
Oh, it's not a stress-free, low pressure 15 minutes application like they advertise it. It's fekkin pain in the ar$e one hour job, you're swetting your ar$e off. And - I guess - you can never get it perfect at the end. There will always be a bubble or misaligned edge somewhere (or is it me?).
Long term use review to follow.
Click to expand...
Click to collapse
Any update to report? I'm thinking about buying one and would like your oppinion since you've now had it for a while.

Dimitri- said:
Folks,
I bought it and had it send to Holland. Took about 1 to 2 weeks but ok I am not in a hurry.
The full body covers basically all the shiny black plastic plus the screen. The rest (middles of the sides and the front keys) are not covered. Also offcourse the camera, speakers etc are not covered. However, and this is probably the difference between P3600 and P3600i the front camara is covered by the shield blurring the image. Now I have already put it on the camera but the next time I would use a hole puncher to add the extra hole. I probably will use a sharp hobby knife to cut an extra hole (on the other hand I never use video conferencing).
The plastic is more stronger and thicker then normal screen protectors. Haven't tried to scratch it on pupose and guess what I am not going to do it. If a scratch forms by accident I will mention it here.
The screen takes some getting used to with the new cover. The plastic does not "slide" as easy as the original screen protector or the screen itself. Maybe this is just in the first period.
The application process it pretty easy if you just take the time. Takes about 30 minutes if you do it slowly. Only 2 minor bubbles on the back but those are not really an issue, the rest is perfect.
Hey for 20 euro's I think it is a good deal. No horrible rubber case or GPS blocking metal case for me anymore. Only downside is that if the phone is dropped now there is no protection. This is only against scratches.
Lifetime guarantee so lets see how often I have to send it back.
All in all recommended so far (but that is just after 1 day of use)
Click to expand...
Click to collapse
Same question for you... Any updates? Thank you...

Definately recommended
After using it a few months I still think it is definately worth the few euro's. Ok it sticks a bit when calling for a long time and I think I even managed to get a small scratch on it but I sort of abuse the fact that I have the shield. Store it with keys, never use a case etc.
No I have bought some useless accessoires such as aluminium case (blocks GPS) and the remote for mediaplayer but the shield I would really recommend.
Cheers,
Dimitri.

Screen getting small scratches

Despite being careful, my screen is increasingly getting scratched. The scratches are only noticeable when the device is off (thank goodness).
If there are any other persons with the same problem, please post here.

I guess that you did not use a screen protector, right?

Correct. I also own a TyTn II and have no issues with the screen whatsoever. Of all the devices I have owned over the years, only this TC has been an issue.

I was noticing the same so applied the included screen protector... I usually don't bother as I don't like them and the device is a throwaway after a year anyway so it's not a big deal. But in this case I figured if it was like that after a few weeks then after 6 months I'd probably not be able to see the screen!

I've had a few Palm devices before i switched to WM and i noticed this scratching as well......Luckily i'm using the included protector.
I have to say on my previous Palms i didn't have this problem, also while using a protector, which makes me suspect that the stylus is the real problem here.
Any thoughts on this?

I use the screen protector, and also got some spares. I also cover the whoel device with a liquid "screen" protector to helpthe faces from getting ruined. So far so good

Problem with the Touch Cruise (Polaris...) is, that the screen is - unlike the Kaiser's - flat and not indent. This means, its exposed to EVERYTHING it touches. Thus chances are higher you'll get one or two scratches once in a while.
Second thing which I can only cite other ppl on other forums: those Polaris allegedly have a softer top layer to be able to operate the unit using only your finger. This would support catching scratches as well...
I'd use the protector. It's a shame having scratches on that mirrored surface.

Schaggo, can you indicate what other forums people are commenting about the screen?
I am interested in your view that the top layer is softer than most others.

i agree that the stylus is the problem ... to much thin... , i tried one from nintendo ds , it's much more rounded and it slide better ( sorry for my english...)

vdavide said:
i agree that the stylus is the problem ...
Click to expand...
Click to collapse
Yeah, I'm using one from my old IPAQ !

ou guys use other styluses? I use my finger, thats what the Touch series should be made for I know it doesnt really work, the fonts are way too small...
Hicksville, I cannot judge what the other ppl say because I used the protector right away. Nothing ever touched my screen without the protector applied. But as I got it, the top film seems to be made of a softer material than the one of other WM devices. Reason for that is the reason for the "Touch" in the devices name: to make the touch layer register the actual point, where the finger tries to point at. If the top layer would be harder/stiffer it allegedly cant tell where exactly the finger tried to hit the screen because the area involved ('touched' eg. pressed down) would be bigger than with a soft top layer. Thats what I got and which makes some sense.
And logically a soft surface is more prone to be 'hurt' than a surface made of hard material. So I guess this might be connected. But I have to repeat, these are all assumptions by users and in no way official statements.

I've been using my phone w/o a screen protector, and I haven't gotten any scratches. Like schaggo I mainly use my finger. I did however test the screen by applying a lot of pressure with the stylus in a sweeping motion, and I didn't get any scratches (don't ask me what possessed me to try this). I later tried a much more conclusive scratch test on a CDMA Touch unit in a store on both the screen and the body and got no scratches! Yes, I applied a lot of pressure, (However, someone else had managed to put a scratch on the CDMA Touch's screen, but that scratch was really deep and probably done with a really sharp object; on the other hand, I did my testing with my TC stylus). I coudln't scratch both the body or the screen using a lot of pressure from my stylus and my nails. Maybe some of you exposed the TC to coins or keys inadvertantly?

That's pretty gutsy to test it on your own device. I am using the screen protector and I have a few scratches on that which is fine. When the time comes, I'll replace it with a new protector. As far as the rest of the case, I have been very careful so far with my device and haven't gotten any scratches anywhere on it. I think that suede/rubber whatever feel of the device is nice but I think it will scratch.

hambola said:
That's pretty gutsy to test it on your own device. I am using the screen protector and I have a few scratches on that which is fine. When the time comes, I'll replace it with a new protector. As far as the rest of the case, I have been very careful so far with my device and haven't gotten any scratches anywhere on it. I think that suede/rubber whatever feel of the device is nice but I think it will scratch.
Click to expand...
Click to collapse
Yes, very gutsy, I pushed hard enough to watch the screen sink it and rise back up very slowly...I don't know what I was thinking, but hey it turned out well w/o any scratches. The plastic on the screen is a lot stronger than your typical screen protector, so that fact along with my tests pretty much confirmed it for me. Furthermore, I don't like the look of screen protectors and I'm worried that they'll hinder touch flow.
As far as the casing, it seems bulletproof. But I'm like you, I keep it in the oem suede/microfiber case whenever its not being held to my ear for a phone call, and I've never put it in a pocket with anything else.

Actually with the suede comment I was talking about the body of the actual device. I'm not sure what that is but it has a nice texture to it. I haven't used that pouch that came in the package. Not a big fan of it. Head on over to the acc forum to see which cases people like. As far as the screen protector goes the original one does not hinder touch capabilities. Also in the acc forum they discuss different screen protectors, you might wanna check out one of those as well.

The Diamond screen-protector

Ok, i've had a problem with it, first i removed the protector that was as large as the device and made the screen very ugly, then i got the one from the box and putted it on, every air-bulb was gone when i kept rubbing etc.
1 stayed, under that bulb there was something white, i found out it was a 'piece' of dust.
It was kind of annoying so i removed the screen-protector, now when im trying to put it on i get lots of 'dust-bubbles',
Anyone has an idea of how to do it or should i just leave my diamond without the screen protector?

Protection
Personally i prefer to have a screenprotecter on my device. I can recommend invisible shield. its very durable and will not be scratched. check it out on www.zagg.com

If you remove the protector, then there will alway be dust next time, because the dust get stuck to the protector glue. (I have also remove mine several times)
I have tried zagg, but I can't recommend it. It is a little sticky (which they also says on their homepage) and I don't like that. The floating feeling is gone. It is also not that invisible.
I have selected to buy a new original protector, and will use that.
The trick to get it on without bobbles is to start on the long edge and then slowly add it. (Keep the 'paper' on as long a possible).
(Michael

willyy1991 said:
Ok, i've had a problem with it, first i removed the protector that was as large as the device and made the screen very ugly, then i got the one from the box and putted it on, every air-bulb was gone when i kept rubbing etc.
1 stayed, under that bulb there was something white, i found out it was a 'piece' of dust.
It was kind of annoying so i removed the screen-protector, now when im trying to put it on i get lots of 'dust-bubbles',
Anyone has an idea of how to do it or should i just leave my diamond without the screen protector?
Click to expand...
Click to collapse
The original is washable. Wash it and dry it with a paper towel that sucks in the water bubbles, wipe dry and clean your screen and reapply it.
By the way, this goes to Accessories forum.

mhfalken said:
If you remove the protector, then there will alway be dust next time, because the dust get stuck to the protector glue. (I have also remove mine several times)
I have tried zagg, but I can't recommend it. It is a little sticky (which they also says on their homepage) and I don't like that. The floating feeling is gone. It is also not that invisible.
I have selected to buy a new original protector, and will use that.
The trick to get it on without bobbles is to start on the long edge and then slowly add it. (Keep the 'paper' on as long a possible).
(Michael
Click to expand...
Click to collapse
Where can you buy a new one, i need it really fast because my phone is without protection right now and no i am affraid of pressing it to hard to leave a permanent mark..
tnyynt said:
The original is washable. Wash it and dry it with a paper towel that sucks in the water bubbles, wipe dry and clean your screen and reapply it.
By the way, this goes to Accessories forum.
Click to expand...
Click to collapse
I did this and the dust keeps coming at the protector and my phone and there will be bubles because the dust gives it a 'height-problem'..

I bought invisible shield for mine, its pretty nice after say 4 days from install.
For first 2 days it might seem really bad but it gets much better.
I somehow scratched it without even noticing it, so I sent picture to zagg and they sent me new one. Even though scratch was very minor.

mhf
hi. this my first post on this web site
excuse me for my bad english
i have a diamond and i remove orginal screen protecter because i write sms with letter recorgnizer and the area that i write words on the screen become white and scratch. i remove orginal and buy a new one that for iphone. i cut it for my phone size and apply it. its sooo much stiky and i have a problem like orginal one.i wnat to remove it and when i do it a tiny layer of glue stand on my diamond screen. i can't clean it. and it give a bad scene to my diamond.
what's your idea. i give u a pichture from my diamond screen.

Perhaps you could use isopropyl alcohol, usually it will remove glue without damaging the plastics surface (in that case: your display). DON'T USE nail polish remover, acetone or even benzine, it will remove the glue too - but your display would look "milky". You can get isopropyl alcohol at the pharmacy.
Tell us if that helped you

mhf said:
hi. this my first post on this web site
excuse me for my bad english
i have a diamond and i remove orginal screen protecter because i write sms with letter recorgnizer and the area that i write words on the screen become white and scratch. i remove orginal and buy a new one that for iphone. i cut it for my phone size and apply it. its sooo much stiky and i have a problem like orginal one.i wnat to remove it and when i do it a tiny layer of glue stand on my diamond screen. i can't clean it. and it give a bad scene to my diamond.
what's your idea. i give u a pichture from my diamond screen.
Click to expand...
Click to collapse
You might be interested in this thread: http://forum.xda-developers.com/showthread.php?t=421229

I didn't get a screen protector with mine... I mean, I had a shipment protector with a little tab for peeling off, but nothing came with it for long term use. It's a Sprint, did they just not include one?

the exim screen protector is very good and smooth

I always use the Brando screenprotectors. See their online shop. They ship worldwide for only $ 3,00 shippingcosts.
It is very easy to install, easy to clean, 100% garanteed scratch free and very durable.

iixnullxii said:
I didn't get a screen protector with mine... I mean, I had a shipment protector with a little tab for peeling off, but nothing came with it for long term use. It's a Sprint, did they just not include one?
Click to expand...
Click to collapse
I've got a Sprint Diamond too, and didn't think I got a protector either, but it was in the separate bag that has the manuals. It should have come with one...Wish it woulda come with an extra one too, oh well.

I had the same problem with misalignment and dust bubbles with the HTC protector on my first few tries...i did however fix the problem...
Take the protector off and clean off the phone...use a microfiber cloth to get all the dust and oil off...after its super clean...take the protector and wash it off with some mild soap...rub the soap in with your fingers and get it clean. Be sure to note which side is down. After its clean, hold it around the edges and let the water bead off...i blew on the protector to get residual water off...some water is ok...actually helps with the install...the basically carefully apply it still holding the sides making sure not to leave finger prints. Start from the top and work your way down... i used a credit card pushed against the microfiber cloth to squeegie the protector down...be carefull with the few drops of water. After you have it down...there might be little bubbles or what looks like water spots where water is trapped under the screen...dont worry...just use your phone and leave it alone. Once it heats up from the excessive phone use it will start to dry up and the protector will come out very nice and smooth. Mine is flawless and i did the wash with soap apply and remove at least 3 or 4 times to get it right...Just be patient

I use screen protector from martinfields, what do you say about, anyone have one??
I think the best in market

My HTC one got a nasty scratch in it last week, so I ordered a Martin Fields.
It arrived this morning and I've got it on without any problems. So far I've noticed:
- It's not a perfect fit like the HTC one was. The hole for the speaker at the top is larger than the hole in the phone. It's not bad though.
- The visibility of the screen does seem better than the HTC protector, but I don't know if it's just the placebo effect of having a more expensive protector.
- It was _easy_ to put on, no bubbles at all
- The protector for the bottom buttons is awful. The circle is just the right size to completely hinder using the touch wheel and it's obvious that you've got a piece of plastic on there.
- It seems smoother than the original HTC one when using the stylus.
So far I'm impressed with it. I didn't bother with the camera hole or bottom hard buttons. The in box HTC one was fine for me, but when I got a scratch on it (my stylus somehow developed a sharp edge), it annoyed me.

I'm using the one supplied as standard with a uk CompactIV and it's great- you can hardly tell it's thereand the sensitivity seems fine.

I have 24 diamond screen protectors. Because i bought 24 diamonds and sold them all without screen protectors so i am sorted untill i buy another phone.

After using the martin fields one for a couple of days, I think it's great.
The screen looks much brighter and clearer through it (I thought the HTC one was great, but I do notice the difference). Plus the smoothness is brilliant, theres pretty much no friction for the stylus or fingers

where can i purchase the htc screen protector? the original that comes in the box...

Best Scratch Guards: Best Skins Ever vs Invisible Shields vs Ghost Armor vs Body Guar

Every gadget owner loves their devices be it Cell Phones, Laptops, GPS, Gaming Consoles, etc. and would never want our devices to get scratchy, dirtily, peel off or loose their color and shine. For this some of us freaks keep cleaning out devices or cover them with cheap looking low quality plastic guard just to see it getting peeled off soon and getting all scratches just to buy another one in few weeks. This is because many of us are unaware of some of the finest Body Scratch Guards which themselves can never attain a scratch.
Yes, that’s true and this article is about Top 4 Body Guards covering not just the screen but the complete body of your device, that I came across. I’ll just be giving my honest reviews about all four of them and leave the rest on you to decide which you prefer.
you can find the comparison here:
http://winmo.techparaiso.com/best-s...isible-shields-vs-ghost-armor-vs-body-guardz/

Well based on peoples experience here....http://forum.xda-developers.com/showthread.php?t=398021
I can safely say Invisible shield is not a good solution. Generally anything that adheres to your device runs the risk that your finish will lift off if you ever decide to remove the shield.

band27 said:
Well based on peoples experience here....http://forum.xda-developers.com/showthread.php?t=398021
I can safely say Invisible shield is not a good solution. Generally anything that adheres to your device runs the risk that your finish will lift off if you ever decide to remove the shield.
Click to expand...
Click to collapse
i would still like to see some screenshots of bestskinsever for diamond as nothing is available anywhere.

want the best protector? Buy a psp HORI Protector, cut to size. 100% invisible and only a knife will scratch it. 2 for .99 on ebay

I'd also love to hear people experience with Best Skins Ever. I'm a sucker and always buy the zagg.com stuff, price = quality after all... but would be willing to grab a BSE skin based on peoples reviews, as the markup on zagg.com is ridiculous.
One thing, I dislike with the zagg.com skins is, after a while the protector appears as if it has a gasoline like stain in the middle of it, symmetrical to about half an inch away from the edge of the screen on all sides. So basically a mini rectangle on the inner portion of the display. Any else experience this? and does the BSE have this tendency?
P.S. Don't forget BodyGuardz

I've been using Invisible shield by Zagg since I bought my Diamond and I completly agree with Lokosis. I also feel the corners are becoming a bit rough, it looks like someone can just pull it off.
* Doesn't fit into my HTC pouch anymore (see picture attached).
* Attracts a lot of dust.
* Don't need a bulky case anymore.
* Gives the back cover a shiny effect.

well yesterday i received my best skins for diamond. i must say delivery was really fast but a little disappointed. i'll tell you why later.
also i'll be posting the pics of my diamond soon.

I bought a full cover from invisible shield about a week and a half ago but am still waiting for it to be shipped to me since I live in Australia and there is not stock here.
Didn't realize there was a cheaper alternate to it. I've got to say I'm a bit worried after just reading that post that says it can damage the screen when you remove it after a while...but hopefully I will never have to remove it

AdamHC said:
I bought a full cover from invisible shield about a week and a half ago but am still waiting for it to be shipped to me since I live in Australia and there is not stock here.
Didn't realize there was a cheaper alternate to it. I've got to say I'm a bit worried after just reading that post that says it can damage the screen when you remove it after a while...but hopefully I will never have to remove it
Click to expand...
Click to collapse
nothing to wory dude. even i first bought IS and den after an hour got to know about BSE so i ordered that too. i'd a talk with IS ppl and they say that when i receive the item, then i should take out the screen guard, put it in envelope and send it back to there address. thats it. they said they dont need the box of spray or anything. just the invisible shield in an envelope. and as soon as they receive it, they'll refund you the money. sending it back in envelope is much cheeper and you save alot. so order BSE now and wait for IS to arrive and send it back

invisible? are you blind?
Well, it's a good screen protector, but it's definitely not invisible...
Are you blind guys?
I just got the screen one and not the whole case skin because I own an o2 Ignito which has a lovely-grippy-rubber-feeling-matt-black back cover, although it is not as sexy as the standard Diamond my wife has.
I was honestly quite disappointed because it is expensive and honestly looks crap compared to cheaper alternatives.
Have you ever tried Vikuiti by 3M guys?
I have it on my Orbit (it's a PSP screen protector, I opened the Orbit and cut the film on the proper size of the display, once re-assembled you can't see any edge at all) it's impossible to leave fingerprints and it is anti-reflection.
The Diamond one is gloss finishing instead, it costs € 8 on eBay (german seller but ships worldwide)

The invisible shield finally arrived. It wouldn't stick to my screen...lol
Well it stuck to the screen, just that the edges are supposed to bend and protect the sides too and no matter how long i held the edges in their positions for they would just unpeel themselves after a couple of minutes. Gave up on the screen, the rest all went on easily and without any visible bubble thingies. I'm not sure if I really care enough to get a new screen protector for the screen, I was more worried about the back of the phone to be honest
Still kinda dissapointed that the screen protector ended up failing for me

AdamHC said:
The invisible shield finally arrived. It wouldn't stick to my screen...lol
Well it stuck to the screen, just that the edges are supposed to bend and protect the sides too and no matter how long i held the edges in their positions for they would just unpeel themselves after a couple of minutes. Gave up on the screen, the rest all went on easily and without any visible bubble thingies. I'm not sure if I really care enough to get a new screen protector for the screen, I was more worried about the back of the phone to be honest
Still kinda dissapointed that the screen protector ended up failing for me
Click to expand...
Click to collapse
i really don understand where u guys fail. i understand that d edges don stick up but it takes half an hour effort to do it. its easy but takes times and u constantly hav to make it stick.
rest both BSE and IS are great. the point is to make it wet properly and den apply.
the only issue i had is that the IS solution went in my front camera screen and has made it blurred.
rest both are the same according to me.
also to be noted that you do not need to use IS spray. instead you can even put your IS in soapy solutions and apply it like BSE.
the aim is to 1st attch is properly on front screen. let it dry and then bend the edges.

sunnyin86 said:
i really don understand where u guys fail. i understand that d edges don stick up but it takes half an hour effort to do it. its easy but takes times and u constantly hav to make it stick.
rest both BSE and IS are great. the point is to make it wet properly and den apply.
the only issue i had is that the IS solution went in my front camera screen and has made it blurred.
rest both are the same according to me.
also to be noted that you do not need to use IS spray. instead you can even put your IS in soapy solutions and apply it like BSE.
the aim is to 1st attch is properly on front screen. let it dry and then bend the edges.
Click to expand...
Click to collapse
I used enough of the solution, got it lined up perfectly with the phone. It was the edge bits that have to be bent to protect the sides where I went wrong. Just couldn't get them to stick and stay stuck properly for some reason

AdamHC said:
I used enough of the solution, got it lined up perfectly with the phone. It was the edge bits that have to be bent to protect the sides where I went wrong. Just couldn't get them to stick and stay stuck properly for some reason
Click to expand...
Click to collapse
it takes alot of time for sure. for half an hour i kept trying and thought maybe the adhesive wasnt strong enough. but there are two things, 1st you have to use alot of spray to smoothly allign it on screen and then this excess spray avoids the sides to stick onn. so patience, repeated efforts and only when the solution dries up, that is when it starts to stick onn. very tough for sure but in the end it pays off.
BUT the diff bet IS and BSE is that BSE only covers the screen and does not cover the sides so there is no bending problem like IS.

sunnyin86 said:
it takes alot of time for sure. for half an hour i kept trying and thought maybe the adhesive wasnt strong enough. but there are two things, 1st you have to use alot of spray to smoothly allign it on screen and then this excess spray avoids the sides to stick onn. so patience, repeated efforts and only when the solution dries up, that is when it starts to stick onn. very tough for sure but in the end it pays off.
BUT the diff bet IS and BSE is that BSE only covers the screen and does not cover the sides so there is no bending problem like IS.
Click to expand...
Click to collapse
In that case I think I might buy one of the BSE. I think that trying to protect the sides is simply too much effort and is tedious. Besides that, the sides are fairly scratch resistant and you can't even see those scratches if them do occur without having to look for them anyway. I really think IS should have skipped trying to protect them or made a second piece to go around the outside.

both are sam so betteer to opt for bse. am loving it.

more pros n cons on bse please......
i found that they didn't provide spray bottle....

mygreatdiamond said:
more pros n cons on bse please......
i found that they didn't provide spray bottle....
Click to expand...
Click to collapse
its best not to have spray. as spray gets into front camera and spoils it. best to use simple soap water.

BodyGuardz vs BestSkinsEver
Hello,
Here is my experience. I had a InvisibleSHIELD on my iPod Classic and it was great so I was considering buying one but after reading some of the the feed back it seemed that the product was good but the fit for our diamonds and even the iPhone (which i am now looking for) was not great.
I then heard about BestSkinsEver and because it was so cheap decided to go ahead and try it. I got it over 2 months ago and when I received it I applied it immediately. I have done a few of these so and since I am some what of a perfectionist I applied it to the best I could. It looked OK but after a few weeks the corners started peeling. Also due to the way the backing is placed it puts stress in areas which causes other areas to lift off (this is mostly on the corners). I ended up using a nail clipper to start clipping areas that were peeling off. After about 2 months it started to peal even more so I decided to go back to the reviews and see what was available. After doing some research I decided to go with the 12 piece BodyGuardz. It came in a set of 2 which is nice when i transfer the phone to my wife.
So all of this is to tell you that my first impressions of the BodyGuardz is well as good as I felt when I put the InvisibleSHIELD on my first iPod Classic. For me it did take a while (about 2-3 hours) to apply. This was not done in one sitting but instead because it was a 12 piece I applied each piece with 10 minute intervals allowing for tackiness to set in and so it would be easier to handle as I continued with the many pieces. First major thing I noticed and was really happy about was the BodyGuardz stickiness was considerably more than the BestSkinsEver. It stuck to the corners almost right away. Although throughout the process I did press down on the corners it was quite a bit easier as the BestSkinsEver did not have good stickiness. Also on a side note when i removed the BestSkinsEver it came of like a sticker which i know from my previous iPod is not normal and it usually takes a lot more effort to get it off carefully. Overall I am very happy at my first impressions of the BodyGuardz and the quality of the material seems to be better than the BestSkinsEver. Not to mention the 12 piece may seem like a lot of work but having individual pieces allows for no stress on the film in weird areas allowing it to sit flat with no parts lifting off (so far, i'll update in a month or two). Which is not the same case for the BestSkinsEver and from what I hear the InvisibleSHIELD. Newayz I hope this review helps someone.
Justin

Mr. Makk said:
its best not to have spray. as spray gets into front camera and spoils it. best to use simple soap water.
Click to expand...
Click to collapse
I never sprayed the device only the shield itself. I would not recommend spraying the device. That said I do like the spray on the shield as it is a bit more even but you can use any spray bottle. I got one with Bodyguardz but there was not enough fluid in it so i had to fill it up with my own solution newayz.

Nillkin Fresh: Review

Hey everybody, got a new case review. This one is the infamous Nillkin Fresh, which is Nillkin's second generation of flip covers. To be honest, I got this case because it works with the iloome ScreenMate tempered glass protector I got, which didn't work with any of my other cases.
I got the yellow color, and it looks very nice. The flip has a darker yellow than the snap on part, which looks perfectly fine to me. The flip doesn't stay down for the first few days, and it doesn't have a lock mechanism. But, with a few days use, the flap does stay down on itself. Now, at first it wasn't working with my tempered glass protector, so I just kept stretching the fake leather out, and eventually it stays. I just clamped it so it stayed stretched. This is a very simple case, and if you don't drop your phone a lot (like me) this is a really nice case, it has a soft lining on the inside of the flip, almost like micro-fiber, and it helps keep fingerprints away. I do like this case, but it's not perfect. You can also use it as a stand, just fold it back and slide it into the slot. I absolutely HATE this feature, as the slot sticks out from the back of the case, so I can't use it with the Orb Charger. I forgot to take pictures of it, but it is REALLY annoying. Overall, aside from that one thing, it's a really nice case. :laugh:

Just to add on to OP, mine's the light blue one, a really sweet colour.
Has a microfiber (or whatever you call that) lining, prevents the screen from getting scratched.
The thickness. When paired with apps like Proximity AutoLock. you simply flip the cover and BAM, the phone locks itself. (Disclaimer: The app takes up quite a lot of battery though.)
Thickness again.
Thickness compared to a bumper. (if you haven't realized yet, I like blue )
The back plastic has got this pearly, glittery effect, too subtle to notice unless you're staring at it.
The front is a leathery kind of texture. Not real leather, of course.
It does destroy the edge swiping experience, with the exception the left hand side center (shown in the pic). May cause full screen SPs to bubble up too, but I have no idea, I don't use full screen ones.
How it looks. Mine has yet to become seasoned, so it'll topple if I don't support it. It has a hook that'll hook the front cover.
The headphone jack.
Those with a dbrand skin might want to take note, it kinda leaves a mark on the skin, but if you don't use the case for long enough, the mark'll go away.
I'd recommend it 8/10 overall as it makes it hard to use the phone using your left hand with the front flap, also, it makes my phone feel like a tank. But the front protection is great if you're not using a screen protector. But be careful of oil stains, they're almost impossible to remove from the inner lining. Washed it once, dried it and it feels like new again.
Edit, does anybody know how the hell do I resize the pictures? They're HUGE.

jiayit said:
Just to add on to OP, mine's the light blue one, a really sweet colour.
Has a microfiber (or whatever you call that) lining, prevents the screen from getting scratched.
The thickness. When paired with apps like Proximity AutoLock. you simply flip the cover and BAM, the phone locks itself. (Disclaimer: The app takes up quite a lot of battery though.)
Thickness again.
Thickness compared to a bumper. (if you haven't realized yet, I like blue )
The back plastic has got this pearly, glittery effect, too subtle to notice unless you're staring at it.
The front is a leathery kind of texture. Not real leather, of course.
It does destroy the edge swiping experience, with the exception the left hand side center (shown in the pic). May cause full screen SPs to bubble up too, but I have no idea, I don't use full screen ones.
How it looks. Mine has yet to become seasoned, so it'll topple if I don't support it. It has a hook that'll hook the front cover.
The headphone jack.
Those with a dbrand skin might want to take note, it kinda leaves a mark on the skin, but if you don't use the case for long enough, the mark'll go away.
I'd recommend it 8/10 overall as it makes it hard to use the phone using your left hand with the front flap, also, it makes my phone feel like a tank. But the front protection is great if you're not using a screen protector. But be careful of oil stains, they're almost impossible to remove from the inner lining. Washed it once, dried it and it feels like new again.
Edit, does anybody know how the hell do I resize the pictures? They're HUGE.
Click to expand...
Click to collapse
You could just use a photo editor and re-crop?
Sent from my Nexus 4, the only phone approved by Patrick Star

N4ever said:
You could just use a photo editor and re-crop?
Sent by a giant douche
Click to expand...
Click to collapse
While we're doling out advice, I recommend that you change the text you quote so everyone doesn't have a second column of gigantic images...

N4ever said:
You could just use a photo editor and re-crop?
Sent from my Nexus 4, the only phone approved by Patrick Star
Click to expand...
Click to collapse
You could have said that without quoting the images all over again....

I have this case too, just never got around to finish writing my review. Mine is mint green (though some product pictures may appear turquoise).
Having a front cover in addition to the case is definitely nice, as I can drop it into my bag without worrying about what is going to hit against the front screen. Also very handy when talking on the phone with the flap covering the screen.
It's not slim as a ringke slim but not thick either, and the phone looks nice in it. I liked that it didn't have an actual lock to keep the cover on because it was easier to flip open.

It's so annoying when your holding it open. No comfortable way to do it.
Sent from my Nexus 4, the only phone approved by Patrick Star

Are the buttons easy to press?
Sent from my Nexus 4 using Tapatalk 4 Beta

Tbh it's quite hard. And trying to take a screenshot with both buttons is a nightmare. But I don't take that many screenshots anyway and the power button is not really that hard to press, it's just that their opening hole for the power button is a tad too small.

jiayit said:
Tbh it's quite hard. And trying to take a screenshot with both buttons is a nightmare. But I don't take that many screenshots anyway and the power button is not really that hard to press, it's just that their opening hole for the power button is a tad too small.
Click to expand...
Click to collapse
I can see the volume rocker is exposed when you open the case. The power button looks a bit hard. In my current case(looks like the ringke slim) i had to cut off the bar at the top to gain easy access to power button.
Sent from my Nexus 4 using Tapatalk 4 Beta

The way everything folds is just uncomfortable.
Sent from my Nexus 4, the only phone approved by Patrick Star

I got this case last week, black one. The plastic base is super cheap, there are at least two defects and the frame around the power button is simply bent. Although my flip cover actually rests perfectly on the screen, the plastic part makes noises everytime a little pressure is applied to the sides.
Went straight to the litter bin, I'd rather use my phone naked than inside this thing.
Just my two cents.

Fabriciohss said:
I got this case last week, black one. The plastic base is super cheap, there are at least two defects and the frame around the power button is simply bent. Although my flip cover actually rests perfectly on the screen, the plastic part makes noises everytime a little pressure is applied to the sides.
Went straight to the litter bin, I'd rather use my phone naked than inside this thing.
Just my two cents.
Click to expand...
Click to collapse
Seems like you got a manufacturing defect.. Why didn't you ask for a refund?

Hung0702 said:
While we're doling out advice, I recommend that you change the text you quote so everyone doesn't have a second column of gigantic images...
Click to expand...
Click to collapse
Sent by a bigger douche who calls people out
Sent by an even bigger douche
Sent from my Nexus 4, the only phone approved by Patrick Star