Related
I've XDA neo ,and it's Rom version is old and german one , I want to update using AKU 3.3.13
I start it , but it lasted more than 40 minutes without any result , so I disconnect the pda , and restarted it ,but it stopeed at O2 screen ,the first screen at all ,where typed :
IPL 2.15.0001
SPL 2.15.0001
GSM 02.19.21
OS 3.0.0.0
I don't know what to do now ,plz help me to solve this problem
many thanx for ur reading my ask
What ROM (the update) where you trying to isntall? Was it an official one, or a cooked ROM?
Try to enter bootloader (the three colour screen) bu pressing and holding the com manager button and performing a soft reset.
If this works, download the latest version of active sync and install it, and once that has completed, restart your computer.
Download a WM5 NVID (No Vendor ID) ROM from here and unpack/unzip it into the root of a harddrive (i.e.: C:\WM5ROM\).
Now, put the device in bootloader mode, and within ActiveSync DISABLE connect through USB (Tools->Connection Settings->Uncheck Allow Connect through USB) and plug the device into the computer.
Now run the RUU from the WM5 ROM you downloaded earlier.
Your device should now work.
Many Thaaaaaaaaaaanx
At Last i've got my pda again
it worked very well,thank you very much for your help
by the way , the link for the rom which u've put in ur reply doesn't work but i get the oficial rom 2005 from another website and applied ur steps and everything is going ok
thank you very much
No problem.
The reason the link didn't work is because the FTP server doesn't allow direct access. You learn something new everyday.
how to install hard spl without windows running in kaiser?
can i use some Mtty commands to make this possible?
this should probably be posted in the threads pertaining to HardSPL, and to answer your question i think not. you have to run the KaisSSPL/JumpSPL in order to temporarily overwrite the SPL on the device. and you cannot just overwrite it by flashing HardSPL as you would a rom or we would have done that from the get go and have it included on every rom.
my kaiser has some problems and can not load windows , thats why i need to change spl and try to use other soft to recover problem.
i have problem with processor communication via I2C with PM7500 chip.
may be i have to brick it firs deleting boot and going to serial connection with processor? (like command task 2a - but in my spl this command not working)
thank you
actualy there is no issue for you.
you can not change spl without WM6.
i've got the same probleme.
let me know if you find a solution.
i thought that my tytn ii was bricked. now is alive. Read "Radio Hell" threads... check in what status is your tytn ii... (obviously at your own risk)....
first try with "solved radio hell thread", but if you erased all by mistake this thread helped me too:
http://forum.xda-developers.com/showthread.php?t=394584&highlight=oemsbl
rumensat said:
how to install hard spl without windows running in kaiser?
can i use some Mtty commands to make this possible?
Click to expand...
Click to collapse
pressing green key not working in 1.93 spl
mtty commands for formating not working with this spl
mtty command don't work for me.
nicx said:
mtty command don't work for me.
Click to expand...
Click to collapse
MTTY should work, just make sure you have unchecked "allow usb connections" in activesync.
rumensat said:
may be i have to brick it firs deleting boot and going to serial connection with processor? (like command task 2a - but in my spl this command not working)
Click to expand...
Click to collapse
which spl version is installed? write down all information shown on tricolor bootloader screen
jockyw2001 said:
which spl version is installed? write down all information shown on tricolor bootloader screen
Click to expand...
Click to collapse
RUUNBH
KAIS130
SPL-3.28.0000
CPLD-8
Serial / USB
rumensat said:
pressing green key not working in 1.93 spl
mtty commands for formating not working with this spl
Click to expand...
Click to collapse
hi,
i had rom radio 1.64.06.04.
for me this command work fine:
Try this from MTTY:
set 16 0
task 8
maybe that's will work for you.
set 16 0 -this command doing nothing
task 8 - reboot unit
at all there is no chance to brick this **** at all
I LIKE TO BRICK THIS **** AND TO START WITH SERIAL DRIVERS
i take off battery in every second when load rom and no chans for me to destroy stupid boot
I remember loading the original HTC ROM when in deep sh*t trouble... no need to have it booted to OS, only to tricolor screen
then you will boot to OS, install SOFT-SPL, then HARD-SPL and your custom ROM, Radio, splash...
i can not boot to Os , i have never seen OS in this unit
rumensat said:
i can not boot to Os , i have never seen OS in this unit
Click to expand...
Click to collapse
when you turn on the device, what do you see? tricolor screen? or white screen? or
you cannot boot to OS even after flashing a stock official HTC rom?
when turn device it is start load windows, after first screen go melodi which i see in rom named LB (low battery), and phone sw off.
i can load any original rom with success, but same story.
i thing problem is in I2C communication between proc and PM7500 chip , register for batt value is nor readable.
thats why i like to remake soft and take off power controll from it, but can not flash hard spl
rumensat said:
when turn device it is start load windows, after first screen go melodi which i see in rom named LB (low battery), and phone sw off.
i can load any original rom with success, but same story.
i thing problem is in I2C communication between proc and PM7500 chip , register for batt value is nor readable.
thats why i like to remake soft and take off power controll from it, but can not flash hard spl
Click to expand...
Click to collapse
Isn't it easier to apply for a warranty replace then?
here in Bulgaria HTC dont have service
Anyway I have seen some note that jocky is going to make the SPL flashable via SD memory card... maybe worth waiting then
BTW have you tried different battery?
Hi,
if your Magician boot in Serial/USB Mode (bootloader) after first install confirmation, you have a problem...
After 1 Min. easy work on PC you can load your OS without more Serial/USB mode screen. (I think all people there have this problem have testet the WM 6.1 rom)
Requipment: Multi-Port/USB TTY (if this don't work, try THIS ONE)
1. Deactivate USB Connection in the ActiveSync Connections Settings
2. Reset your Magician in Bootloader Mode (Power+Camera+Reset at same time)
3. Put the USB Cable in PC and Magician
4. Run Multi-Port/USB TTY and select Port like "\\.\WCEUSBSH001", or "\\.\WCEUSBSH002" and click OK
5. Type "set 14 0" (without " quotes) and Enter-Key on your Keyboard
6. Remove your Battery for 3 Sec.
7. Thats all.
Sorry for my bad english, but i think every body understand the 6 steps.
thanks
the method is working
thanks
working...
working
fix this problem but i cant get WM 6.1 rom can you help for any way?
sticky please:::
I'm sorry, but i have not found a method to get WM6.1 on my Magician.
Maybe there is a Problem with the ROM/Radio version.
I'll test any possibilities and post the working option, if i have find it.
At Moment on my Magician are:
ROM-Version: 1.13.01 GER (Vodafone)
Radio-Version: 1.13.0
Protokoll-Version: 1337.43
I think, the only way to "upgrade" to any ROM (NOT 6.1) is this here: http://forum.xda-developers.com/showthread.php?t=247994
If my supposition is right, became with try to update 6.1 Rom some things in the Bootloader changes.
what kind of problems you have with installing my ROM?
If you want, you can separate installation by two steps:
1)Install 1.12 radio
2)Install ROM
of course your device should be CID unlocked.
Cotulla said:
what kind of problems you have with installing my ROM?
...
of course your device should be CID unlocked.
Click to expand...
Click to collapse
1. RUU.log
Code:
19:54:11:359 [msg] : Version : [1.5.0].
19:54:11:359 [msg] : Config Info : [776571],[1],[1],[0].
19:54:15:656 [msg] : Current Not in CE Mode or in CE Mode but ActiveSync Not Connected.
19:54:21:937 [msg] : Disconnect ActiveSync .... [2]
19:54:22:078 [msg] : Current in BL Mode. Open Port : [\\.\WCEUSBSH002] OK.
19:55:12:781 [err] : BL Get Device Data Error.
2. How to unlock CID?
I have carried out some ROM updates without problems.
Only after the attempt to install WM6.1 no more update works.
Dark Angel [gEb] said:
1. RUU.log
Code:
19:54:11:359 [msg] : Version : [1.5.0].
19:54:11:359 [msg] : Config Info : [776571],[1],[1],[0].
19:54:15:656 [msg] : Current Not in CE Mode or in CE Mode but ActiveSync Not Connected.
19:54:21:937 [msg] : Disconnect ActiveSync .... [2]
19:54:22:078 [msg] : Current in BL Mode. Open Port : [\\.\WCEUSBSH002] OK.
19:55:12:781 [err] : BL Get Device Data Error.
2. How to unlock CID?
I have carried out some ROM updates without problems.
Only after the attempt to install WM6.1 no more update works.
Click to expand...
Click to collapse
thnks Dark Angel
this is my problems and cant updates to any rom
2. How to unlock CID?
I have carried out some ROM updates without problems.
Only after the attempt to install WM6.1 no more update works.
Click to expand...
Click to collapse
it's seems it can't connect to bootloader...
Cotulla said:
it's seems it can't connect to bootloader...[/
QUOTE]
can wrait ok bootloader ?
Click to expand...
Click to collapse
@stb2xxx: How language is(are) your Magician? German?
Magician locked in usb mode
Hi Dark Angel, excuse me for my bad english, I used Multi-Port/USB TTY and other and I can't select: "\\.\WCEUSBSH001", or "\\.\WCEUSBSH002" because they are invisible do you have an idea for me? thanks!!
JPM15 said:
I can't select: "\\.\WCEUSBSH001", or "\\.\WCEUSBSH002" because they are invisible do you have an idea for me? thanks!!
Click to expand...
Click to collapse
You must deactivate the USB Connection in the ActiveSync Connections Settings at first, because the ActiveSync stays the USB connection opened and the Multi-Port/USB TTY cant find it.
I tried several times, but after using this method to fix the problem of serial/USB, I upgraded successfully without any problem
Thanks guys for your support.
Attached you find all you need to flash cooked ROMs on your Dash3G (Maple).
The sspl/hardspl are confirmed to work fine on the HTC Maple platform (Dash3G, SNAP S520, SNAP S521). Any phone that says MAPL1XX under the battery should work just fine with the sspl and hardspl. This has been tested by oOkBa yesterday night. His cooked roms flash extremely fast and he noticed no problems except for the splash screens. Apparently HTC changed the format slightly. Should be easy to tackle and has nothing to do with the sspl/hardspl.
Now for the bad news ... It will not work on the HTC Cedar platform (GSM/CDMA, HTC Ozone XV6175, Verizon). Running the sspl on an Ozone will definitely brick it. Also the HTC Willow platform (SNAP S511, Sprint) is not supported. Please see this post for more info and how you can help.
There are 2 packages both contain a SSPL, HardSPL, patched ROM updater and the original Maple SPL. The first package is based on SPL 1.17 (tested by oOkBa) and the second is based on SPL 1.19 (tested by Gawain1986)
Instructions:
1. remove SD and SIM cards (don't forget otherwise the sspl is likely not to work!!)
2. connect your device to your pc with a USB cable and wait until it is synced
3. extract the file "Dash3G HardSPL by JockyW.zip" and execute "auto.bat"
4. follow all instructions given on screen: first the sspl is copied to the device and executed. You must confirm running JumpSPL on the device: first time you must click Yes to allow it to run, you also must click the trackball to continue execution of JumpSPL. The device display will turn dark and after that the romupdate tool will install the hardspl on your device. (the identification string in the tri-color bootloader screen is "1.17.hard")
5. if you have difficulties to install 1.17 then try 1.19
6. to test the sspl and the hardspl you can flash the attached splash.nbh
Once the HardSPL is installed on your device you can flash any Maple cooked or original ROM.
Have fun,
JockyW
Excellent work!! JockyW is the man! Please donate to a great cause! This now opens the door to amazing possibilities! Thank you thank you!!
ookba said:
Excellent work!! JockyW is the man! Please donate to a great cause! This now opens the door to amazing possibilities! Thank you thank you!!
Click to expand...
Click to collapse
couldnt of said it better myself..
oo..
my Snap 526 is MAPL110..
should i gib it a shot?
but i need a plan b in case something goes wrong.. any idea how to hard reset the snap with the scrollball?
I have the same mapple, ithink it's ok.
before running this file, do we have to dump the rom? and do we have to use the spl backup kit berfore?
(sorry for all these questions)
First of all, there's really no need to run this yet until there are custom ROMS to flash. If you want to simply test or prep, go for it. I can confirm it works in a MAPL100 so I don't see why any other device with MAPL1XX should be an issue. I will build some factory ROMS as well as some custom cooks in the next days for you guys to play with and test.
see i dont think alot of the new people understand the process.
the spl does nothing more than ENABLE ur device for a rom, thats it!
nothing fantastic, its not a completely diff o.s. on ur device..just preps it for whats to come.
what happend with my device today was a fluke!
i was testing and working at the same time..i could have missed a step, one of my work programs on my laptop could have set something off..i dunno.
Bricking usually isnt a part of getting a SPL for a device..just ALOT of testing. SO now is the another part of the process..the waiting process. Waiting for a rom cooker to successfully establish something, test it, and release it.
in this game..u need patience.
So I;ve been trying this and it seems something is going wrong...
Ik run auto.bat, JumpSPL gets copied and started, the device screen goes black, and when I reconnect the USB cable to get the "Smartphone Sync" driver working, my Windows 7 install tells me that there is something wrong with the USB device.
It will then refuse to use any driver I try to add to the device.
Any thoughts?
PS. It's a SNAP S521 (MAPL110)
EDIT: Windows XP x64 has the same problem.
Gawain1986 said:
Ik run auto.bat, JumpSPL gets copied and started, the device screen goes black, and when I reconnect the USB cable to get the "Smartphone Sync" driver working, my Windows 7 install tells me that there is something wrong with the USB device.
Click to expand...
Click to collapse
First, this has not yet been tested on Win7. Second, it should not be necessary to unplug and replug the cable. Try again and just wait a minute or so to allow Win7 to install the driver. Other thing you can do to make sure the driver is already installed is to put the phone in bootloader mode and connect it by usb cable.
ps: it is normal the display turns dark after running the sspl
ok, i understand there are 3 steps. but I would like to know how to do the first one:
dumping my rom.
First I entered the bootload by holding the volume down button and turning the device on...
It said:
Code:
MAPL110
SPL-1.19.0000
MicroP-Maple (LED) v6
ENGID 0x2
PCBID 0x80
PanelInfo 15-0x2
I connected it to the computer and it recognised the Qualcomm phone immediately and settled on the HTC USB Sync driver.
Then I restarted the phone and connected it again, ran auto.bat... it ran SSPL again and I waited.
So after I tried waiting for 5 minutes, WIndows 7 did not see a new device, it stayed with it's normal RNDIS driver.
So I took the plunge and ran the RUU, which told me it could not connect to the phone.
I unplugged the phone and replugged it and it said there was an error regarding the USB device.
Can it be that because my SPL version is higher than the HardSPL or SSPL, that it's getting into conflict with itself?
Hi,
First thanx for your hard working.
I got some trouble when trying to install the Hard SPL.
My SNAP from france, S521 Mapl100 under the Battery; Just HTC no operator
I launched the auto.bat
The device display turned dark and tri-color bootloader screen said "1.19.hard
The flashing process start and stuck at 0%
Unplugged the USB and the phone restart well.
Is this Hard SPL
Enter bootloader. If you see "1.17.Hard" the HardSPL is succesfully installed and you can flash any cooked and official roms in the near future.
Fabtwone said:
Hi,
First thanx for your hard working.
I got some trouble when trying to install the Hard SPL.
My SNAP from france, S521 Mapl100 under the Battery; Just HTC no operator
I launched the auto.bat
The device display turned dark and tri-color bootloader screen said "1.19.hard
The flashing process start and stuck at 0%
Unplugged the USB and the phone restart well.
Is this Hard SPL
Click to expand...
Click to collapse
Gawain1986 said:
Can it be that because my SPL version is higher than the HardSPL or SSPL, that it's getting into conflict with itself?
Click to expand...
Click to collapse
Please first try it on WinXP before we draw wrong conclusions.
Good work jocky - nice to see you about again
Thread Stuck.
Dave
jockyw2001 said:
Please first try it on WinXP before we draw wrong conclusions.
Click to expand...
Click to collapse
Did that immediately after I posted... it just keeps telling me the USB device is "malfunctioning" somehow...
Gawain1986 said:
Did that immediately after I posted... it just keeps telling me the USB device is "malfunctioning" somehow...
Click to expand...
Click to collapse
Ok, if there are similar problems i can try to build a sspl based on 1.19
Please dump it and attach (see first post for the link to the dump kit)
To anyone who has problems, please look up your current SPL version.
(press volume down and power on).
Is there anyone who succesfully flashed the HardSPL where the old SPL version was 1.18.00 or higher?
jockyw2001 said:
Ok, if there are similar problems i can try to build a sspl based on 1.19
Please dump it and attach (see first post for the link to the dump kit)
Click to expand...
Click to collapse
Here you go...
http://www.mediafire.com/?sharekey=cb564520d236e90090a82c7bb0fad7ade04e75f6e8ebb871
Gawain1986 said:
Here you go...
http://www.mediafire.com/?sharekey=cb564520d236e90090a82c7bb0fad7ade04e75f6e8ebb871
Click to expand...
Click to collapse
Try the attached sspl which is based on your v1.19 SPL.
Run sspl.bat (preferrably in XP)
I'm sorry, but the new 1.19 SSPL is not working either. The phone stays in the black screen and both Windows XP x64 and Windows 7 x86 keep telling me the USB device is malfunctioning.
I have had some experience with unlocking my previous Tornado, VOX, Kaiser and X1 and I'm pretty sure I need to see a tri-color scren when invoking JumpSPL.
So maybe that's the problem?
Hi.
In short: After normal using my Diamond just reset himself and screen was snowing, some pixels etc.
When I'm going to bootloader screen is ok, without snowing or something and says:
DIAM100 64M
SOL-2.07.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
Serial
When I plugged usb cable SERIAL changing to USB - so far so good...
I'm using VISTA, I hear sound when I plugging Diamond, ROM Update Utility see device because starting to install Hard SPL but progress is stuck on 0%...
Windows Mobile Device Center cannot see device.
Windows doesn't see device as a removeble disk so I CAN'T COPY NOTHING to my device...
What to do?
I was trying many different HardSPL but nothing... always 0%
Please help....
Hi
You need to read this about HSpl : http://forum.xda-developers.com/showthread.php?t=409425
And this about flashing on Vista : http://forum.xda-developers.com/showpost.php?p=1116596&postcount=1
Additional info here : http://forum.xda-developers.com/showthread.php?t=416211