Related
Hi all,
I always find flashing with a card is a lot faster than using a software because I can do this anytime with just one little card. I didn't find this in wiki so might as well just make one. tested by myself.
***IMPORTANT***
Please make sure you have HardSPL on your device. And also make sure you have more than 50% of battery left or you can plug in a charger just to make sure there is no power failure. I am not sure if SIM unlocked is necessary prior to performing these steps, so hopefully someone (maybe pof) can help me with this. DO THIS AT YOUR OWN RISK.
1. Get a 128MB MicroSD card (or whatever size you like) and format it (***please make sure you format it, but not just delete all contents on it)
2. find the ROM image you would like to use, normally namede RUU_Sign.nbh, and rename it to "KAISIMG.nbh"
3. Plug the card into the phone, then enter boot loader mode by pressing down the Power and Camera buttons simultaneously, and using the stylus at the same time to press the RESET button at the left side. Continue pressing the two buttons for a few seconds after pressing and releasing the reset button until the bootloader screen appears. (taken from Wiki)
4. You will first see a tri-color screen then the information on the card. Press power button to start flashing.
5. After all these are done, press the reset button located at the bottom of the phone to reset the device.
DISCLAIMER
I take no responsiblity for any conflict, fault, or damage caused by this flashing procedure. No warranties of any kind are given.
vip_snoopy said:
Hi all,
I always find flashing with a card is a lot faster than using a software because I can do this anytime with just one little card. I didn't find this in wiki so might as well just make one. tested by myself.
Click to expand...
Click to collapse
Thanks for the finding.
I'll test the card method when i have something fo flash
added to Wiki
Has anyone actually tried this method ?
Was wondering if anyone has tried this method for flashing on of helmi's roms or even the stock htc rom on a tilt and if so which rom did you use
Thanks in advance
And eep the GREAT work up guys
Works a treat
Yes, it works fine. I've flashed HTC stock, Helmi, and Dutty's just fine with this method.
/av
I did this but my kaiser just sits on the boot loader. When you say to make sure hardspl in on the device do you mean to place the hardspl.exe on the root of the device?
vip_snoopy said:
Hi all,
1. Get a 128MB MicroSD card (or whatever size you like) and format it (***please make sure you format it, but not just delete all contents on it)
2. find the ROM image you would like to use, normally namede RUU_Sign.nbh, and rename it to "KAISIMG.nbh"
Click to expand...
Click to collapse
are we supposed to copy the renamed file "KAISIMG.nbh" to the MicroSD card before proceeding to step 3 ??
mp3news said:
are we supposed to copy the renamed file "KAISIMG.nbh" to the MicroSD card before proceeding to step 3 ??
Click to expand...
Click to collapse
YES.................
Well should i try this or not. im downloading htc rom right now. post you back in 20 mins
xdaking said:
Well should i try this or not. im downloading htc rom right now. post you back in 20 mins
Click to expand...
Click to collapse
Update in Progress......
xdaking said:
Update in Progress......
Click to expand...
Click to collapse
Nice nice nice all done
very nice ive flashed the Duttys Hybird with SD card and everything works 100% thanks to pof, vip snoopy and all the developers.
just need to get rid of orange splash screen thats all i want to do now
thank you again
jamespaulritter said:
I did this but my kaiser just sits on the boot loader. When you say to make sure hardspl in on the device do you mean to place the hardspl.exe on the root of the device?
Click to expand...
Click to collapse
hard spl is a dos file you have to run on command prompt while device is connected via activsync (green icon) if you can not power up the device forget about HSPL
HardSPL is a 4 min tiny operation and will save you from bricking your device
If you have low signal, goto settings-> phones -> and select GSM and BAND manualy. this will bring the 4 bars of signal nicely. internet is more faster too
vip_snoopy said:
Hi all,
I always find flashing with a card is a lot faster than using a software because I can do this anytime with just one little card. I didn't find this in wiki so might as well just make one. tested by myself.
***IMPORTANT***
Please make sure you have HardSPL on your device. And also make sure you have more than 50% of battery left or you can plug in a charger just to make sure there is no power failure. I am not sure if SIM unlocked is necessary prior to performing these steps, so hopefully someone (maybe pof) can help me with this. DO THIS AT YOUR OWN RISK.
1. Get a 128MB MicroSD card (or whatever size you like) and format it (***please make sure you format it, but not just delete all contents on it)
2. find the ROM image you would like to use, normally namede RUU_Sign.nbh, and rename it to "KAISIMG.nbh"
3. Plug the card into the phone, then enter boot loader mode by pressing down the Power and Camera buttons simultaneously, and using the stylus at the same time to press the RESET button at the left side. Continue pressing the two buttons for a few seconds after pressing and releasing the reset button until the bootloader screen appears. (taken from Wiki)
4. You will first see a tri-color screen then the information on the card. Press power button to start flashing.
5. After all these are done, press the reset button located at the bottom of the phone to reset the device.
DISCLAIMER
I take no responsiblity for any conflict, fault, or damage caused by this flashing procedure. No warranties of any kind are given.
Click to expand...
Click to collapse
Dear I Have an XDA Atom Life Its Stuck on Logo.
Can You Tell Me How To Flash Via Memory Card.
Bcoz Phone System Is Not Match As Per Your Post .
WBR
Bluffmaster
bluffmaster said:
Dear I Have an XDA Atom Life Its Stuck on Logo.
Can You Tell Me How To Flash Via Memory Card.
Bcoz Phone System Is Not Match As Per Your Post .
WBR
Bluffmaster
Click to expand...
Click to collapse
His quote "DISCLAIMER
I take no responsiblity for any conflict, fault, or damage caused by this flashing procedure. No warranties of any kind are given."
and why would you try something in a Kaiser post for your ATOM? Not quite the same phone.
vip_snoopy said:
1. Get a 128MB MicroSD card (or whatever size you like) and format it (***please make sure you format it, but not just delete all contents on it)
Click to expand...
Click to collapse
Just to clarify this step, for those who may be confused (like I was):
You can format the card using Windows XP and just select "quick format". That was enough to get this process working for me.
To the original author: THANKS! This process allowed me to flash here @ work, where USB flashing fails due to firewall software we have to run.
-Brett.
A couple of shortcuts
1. This will work with any card that's formatted with FAT32. It doesn't need to be blank or freshly formatted. Flashing won't affect (or be affected by) the other data that's on the card.
2. You don't need to use the stylus to start the process. Start with the device off - all the way off. Then press the power and camera buttons at the same time and you should go right into the boot loader.
One last thing. When the update completes you'll see "Update Complete" and "UPDATE SUCCESS". At that point none of the keys work. You will need to do a reset with the stylus. My first flash, I let this screen sit a long time before I was sure that the flash had completed. No need.
Is there a way to flash to an OEM rom with the card? Otherwise, I'll have to wait until tonight.
Thanks.
hi plz help me
i flashed sum touchit rom to my phone and im just stuck in wot i think is bootloader mode
its shows on the tri colour screen
IPL: 3.04.0001
SPL: 1.11.0000
plz help me im ready to make dontations to whoever can fix this problem
HEEEEEEEELLLLLPPPPPPPP
I too am having the same problem. It just sits at the tri-coloured screen basically saying either "Serial" or "USB" (depending if its still connected to the 'puter).
Any ideas how to solve this one? I have the microsd card freshly formatted FAT32 with KAISIMG.NBH clearing sitting on the root of the storage card.
Seems like it's waiting a file to be transferred via USB or some other connectivity method rather than looking on the MicroSD card.
i am ...
really stuck i need sum1s help badly.. plzplzplzplzplz
I have a qtek9000 and a 2gb sandisk sd card. i downloaded
http://vidmes.com//Uni/ROMs/BeastyLeo/2.07.04.BL/Vanilla.rar
and installed it with no problems, system rebooted (before reboot i inserted sd card in) and started installing some cabs and finally rebooted once more.
My problem:
after startup i have this error message ""sddaemon cannot be opened. Either it is not signed with a trusted certificate or one of it's componets cannot be found. You might need to reinstall or restore this file"
and when i check programs i see there are programs that are installed but the icons are blank, and they wont launch.. i also tried rom ranju, same thing...
What am i doing wrong? I serached but i couldnt find any links, if it is posted somewhere, can u please send me a link at least
thnx
RE:
Did you unlocked your mobile, goto the sticky note on WM6 that tells you how to unlock your phone first
for the sddaemon message, goto \windows\startup
yo will find a shortcut for sddaemon, just remove it
Thanks
swunk said:
I have a qtek9000 and a 2gb sandisk sd card. i downloaded
http://vidmes.com//Uni/ROMs/BeastyLeo/2.07.04.BL/Vanilla.rar
and installed it with no problems, system rebooted (before reboot i inserted sd card in) and started installing some cabs and finally rebooted once more.
My problem:
after startup i have this error message ""sddaemon cannot be opened. Either it is not signed with a trusted certificate or one of it's componets cannot be found. You might need to reinstall or restore this file"
and when i check programs i see there are programs that are installed but the icons are blank, and they wont launch.. i also tried rom ranju, same thing...
What am i doing wrong? I serached but i couldnt find any links, if it is posted somewhere, can u please send me a link at least
thnx
Click to expand...
Click to collapse
Hi,
Sounds to me as though you have not cleared your storage after having flashed the roms...... did u hold the two soft keys on the keyboard whilst pressing the reset button and then selecting 0 to clear the storage.
Failing that I wouls use MTTY to restore your DOC.
@mehegazy: if my device is locked how did i install wm6 at all? i can install wm6 and wm5 without a problem, and i can install programs manually...works perfect. problem seems to be with specific roms that install programs automated at startup.. Also removing the shortcut from the startup actually doesn't resolve the problem, cause that means that program is not working...
@beast0898: i ve cleared the storage, that can't be the problem..
Funny thing is, after reboot it installs some programs and resets without a problem. But i see that some programs are installed and some of them has blank icons that do not launch..
Also is there a wm6 rom that actually modified for the best performance of system + without apps?
thanks all for helping
Hi,
I'm sorry about this post but there seems to be an anormous amount of information which doesn't make a lot of sense to me.
All I want to do is upgrade my palm treo 750 from win5.0 to 6.1.
I've downloaded the rom but it doesn't upgarade. So I need to figure out a way to flash this phone so it can be upgraded to any roms.
I have tried the Cheetahunlocker which doens't work. It gets stuck on 0% then times out.
Could someone please give me some basic instructions on the best way to do this on the treo.
I've done this on the TYTN2 whith no issues however on this phone, it seems to be a lot harder.
Thanks in advance.
Your device needs to be unlocked. You can do this by calling ATT and getting unlock code or by using Magic_Unlocker.
search
Also you will need to have the HardSPL installed which is Step 1 only of the CheetahUnlocker
I just did it yesterday so I know it works.
After you get the phone unlocked, name the ROM .nbh file CHEEIMG.nbh and then put it on the SD card
The start the CheetahUnlocker process as it enters the HardSPL process it will go ahead and run the CHEEIMG file and flash your ROM
(it works ! ) DON"T CHANGE THE RADIO !!!!
After doing that be sure and reclaim your ROM space - search web for Removing Ext ROM and do that process, hard reset and you are ready to go
Takes about 15 min!
jcrompton said:
After you get the phone unlocked, name the ROM .nbh file CHEEIMG.nbh and then put it on the SD card
Click to expand...
Click to collapse
Thanks for your info.
sigh..
The rom is an exe file...
I downloaded 7-zip, extracted the rom to a folder.
Looking through it, I am unable find the ROM.nbh file!
CHEEMING.nbh is already there..
What am I doing wrong?
Thanks.
artii said:
Thanks for your info.
sigh..
The rom is an exe file...
I downloaded 7-zip, extracted the rom to a folder.
Looking through it, I am unable find the ROM.nbh file!
CHEEMING.nbh is already there..
What am I doing wrong?
Thanks.
Click to expand...
Click to collapse
Sorry I forgot it was already named CHEEIMG.nbh -- just use it like I said above.
Copy it to the SD card, put the SD card in the device and after you have used Magic_Unlocker , connect via Active Sync and start the CheetahUnlocker process. This will start the three step CheetahUnlock process (really all you need is step one which will put the HardSPL in place) as that process fails the CHEEIMG file on your SD card will get flashed.
Hope this makes sense
Bottom line is that you will be doing an SD flash of the CHEEIMG.nbh file but it takes HardSPL for that to work. Step one of the CheetahUnlocker installs HardSPL (that will be all you need of that process)
remember!
THE SD FLASHING METHOD TAKES A REALLY LONG TIME. SO LONG YOU MIGHT THINK IT'S BROKEN. BUT IT'S NOT!!!!
caps with bold and red= great way to emphasize an important point.
Thanks for the info but I'm still running into trouble.
I copied the file to the SDcard but when running the cheetahunlocker, it give the same error at 0% ( error 206) something about the connection..
I notice that active sync turns off when the cheetah unlocker goes to the coloured screen.
Edit:
Also, should I be moving the CHEEIMG.nbh or just copying it to the SD card?
Thanks.
artii said:
Thaks for the info but I'm still running into trouble.
I copied the file to the SDcard but when running the cheetahunlocker, it give the same error at 0% ( error 206) something about the connection..
I notice that active sync turns off when the cheetah unlocker goes to to the coloured screen.
Click to expand...
Click to collapse
Did you run the MagicUnlocker first?
Is the CHEEIMG.nbh file in the root of your SD card? Try re-formatiing your SD card (FAT32 important!) and then putting the CHEEIMG.nbh file in place on the root of the SD card.
After starting the CheetahUnlocker the TriColor screen should come on and then it should go to a standard White boot scan. It will ask if you want to flash and you will be asked to confirm by pushing the Power button.
If you can ever get Step One to complete on teh Cheetah Unlocker you should be able to confirm that the HardSPL is installed by turing off Today screen (Red, end button) , then hold the left side button while then pushing the reset button. You will get a tricolor screen that lists your SPL version. If it is HardSPL on an unlocked device and there is a CHEEIMG.nbh file on an inserted SD card it will then automatically go to a White boot screen .....
If any of this sounds foreign to you then you need to familiarize yourself in the Wiki re SD flashing
PS do you have the NetFramework 2.0 installed on your PC? When you start the CheetahUnlocker are you getting the Treo device confirmation to install the 2 boot exe files that let the Treo go to the boot screen (you have to answer yes to both of these) - are you making it that far?
Yes I ran the unlocker which worked fine.
I formatted the SD card, copied the CHEEMING.NBH to it so it's the only file there.
No I run the CheetahUnlocker.exe , yes to disclaimer , then STEP 1 - I click FLASH SPL, then next, next etc.. I hit Update - next - next then the phone msg comes up asking if I want to run jumpSPL.exe - I hit yes and it goes to the tri colour screen, the active sync dissapears, the screen on the pc stays at 0% and then I get the error 260: Connection, check cable etc..
How is it suppoed to maintain a connection when Active sync turns off?
I did check and framework2.0 is present.
Thanks.
artii said:
Yes I ran the unlocker which worked fine.
I formatted the SD card, copied the CHEEMING.NBH to it so it's the only file there.
No I run the CheetahUnlocker.exe , yes to disclaimer , then STEP 1 - I click FLASH SPL, then next, next etc.. I hit Update - next - next then the phone msg comes up asking if I want to run jumpSPL.exe - I hit yes and it goes to the tri colour screen, the active sync dissapears, the screen on the pc stays at 0% and then I get the error 260: Connection, check cable etc..
How is it suppoed to maintain a connection when Active sync turns off?
I did check and framework2.0 is present.
Thanks.
Click to expand...
Click to collapse
I'm not sure exactly what is happening in your case but I do know that once a device of any kind enters the bootloader - Active Sync dies - AS is part of the OS and that no longer exists after the bootloader starts, I.e. Windows Mobile isn't really running any longer. the AS connection just gets it started.
I'm not too sure either.
I've unlocked the phone which worked fine.
When I run the cheetahunlocker, it doensn't get past the first step.
Should I be running Hardspl first?
What rom works best with the Treo 750? Link please!!!
What rom are you wanting to use? I have Treo750_WM6.1_WWE_Lite, looking for a more stable rom. Please list some or link them.
I tried both roms
the lite one and the normal one. I must say that the normal one is more stable - with the lite I had to do a reset at least one per day. with the normal version I did not do a reset at all...
Hi, did you resolve this CONNECTION issue? I'm having exactly the same problem.
Anyone?
hey everyone... i have a problem similar to these i think. I'll explain
i've done the magic_unlocker and i can do the 1st step of the cheetahunlocker. treo reset automatically and when i try to flash the rom the trilinear screen doesn't change to the blue screen which is the screen of the rom flash
anybody now why?
i have cracked my head the hole day and a still can't do it :S
artii said:
Yes I ran the unlocker which worked fine.
I formatted the SD card, copied the CHEEMING.NBH to it so it's the only file there.
No I run the CheetahUnlocker.exe , yes to disclaimer , then STEP 1 - I click FLASH SPL, then next, next etc.. I hit Update - next - next then the phone msg comes up asking if I want to run jumpSPL.exe - I hit yes and it goes to the tri colour screen, the active sync dissapears, the screen on the pc stays at 0% and then I get the error 260: Connection, check cable etc..
How is it suppoed to maintain a connection when Active sync turns off?
I did check and framework2.0 is present.
Thanks.
Click to expand...
Click to collapse
If it goes into the bootloader then you should be good to go. Both 750s i unlocked did this. However, if done correctly, the phone should go to a light blue screen where you will press the power button and flashing should begin.
na1kkkk said:
hey everyone... i have a problem similar to these i think. I'll explain
i've done the magic_unlocker and i can do the 1st step of the cheetahunlocker. treo reset automatically and when i try to flash the rom the trilinear screen doesn't change to the blue screen which is the screen of the rom flash
anybody now why?
i have cracked my head the hole day and a still can't do it :S
Click to expand...
Click to collapse
Are you doing the SD method or Desktop? DO the SD method and it should begin flashing right away after the 1st step of cheetahunlocker.
Now, Idk what the heck is wrong with my G1, but it is doing it. -_-
Ok, heres the WHOLE story so sit back and relax...
When I dound this app on atrackdog advertisment it said you could tether your G1 so you could give internet to like your computer or any other wireless picking devices. Now I thought "Hey, why don't I do this?" and so I did. When I launched the program, it said I needed a Root G1. Now, I tryed doing something with my Ipod once and I bricked it. Had to send it back to Apple and got a new one. Anyway, back to the story. I went to the XDA forums thingy were it showed you How To get root on a G1. So guess what I did? You know! lol I tryed to root my G1. Now I got threw ALL the steps were it said "You know have a rooted G1" and I was like YAY, but it ended up not working. I tryed 2 tethering apps that both said I still didnt have a rooted G1. Now that made me p.o'ed. So I try to fix it by downloading updates, renaming them update.zip and etc... ALL OF THEM did not work! I mean come on! The files were RC33 updates I found on the web. I talked to a guy on T-MObile Forums (a MOD named Chris) and he tryed to help me. He went on vacation for the weekend so I will try to fix it myself by asking you guys Back to the story, he told me (chris) that I need towait for a automaticly update during the day. Well I waited and got one. Everytime I try to update it it does the normal rutine. Resets, goes to the box unpacking software to the G1, swirly line, starts to load, and poof! I get a screen that has a tringle with a explimation mark in it. I ushally pressed the alt-l to see the list, aand then pressed alt-s to download from sd. Didnt work (probily becouse it is not coming from the sdcard, but from online ) so I reset phone. Chris (the mod) told me to wait on the screen becouse it might be just loading on there for the update. Well I waited for 3 hours and it stayed on the ! mark! So now I am stuck with a G1 that says it is and isnt rooted (maybe bricked, hope not becouse it still works...) and I REALLY need help!!!
Now I have restarted (meaning master reset) the thing 3 times already! I will do it again ONLY IF this is the only way it will work.
Please Help ASAP!
Yikes. Wall of text FTL. You should have sat down and distilled your entire narrative into a few cohesive sentences. It makes it easier for folks to help you if they can understand what yer sayin'.
Josh27 said:
(probily becouse it is not coming from the sdcard, but from online )
Click to expand...
Click to collapse
You can just put a standard update.zip onto the sdcard (use an external card reader) and Alt-S as normal. If for some reason you can't get the update.zip to work (for example if you already replaced the keys with testkeys) then the absolute end-all-complete-start-from-scratch is to use the DREAIMG.NBH file. Follow steps 1 through 6 in "Preparing to get root" at this thread. After that, you can apply official updates normally.
I suggest you not attempt to root your phone after you recover it.
you need to revert back to RC29, follow the instructions in this thread.
http://forum.xda-developers.com/showthread.php?t=442480
1. Format your phone's SD card to FAT32 mode:
* Hook your phone up to your computer using a USB cable and then wait for the notification to show up in your title bar of your phone.
* Click the notification, and then click "Mount".
* A new removable disk should show up on your computer. Right click it and select Format, and select FAT32 as the file system type.
2. Download and unzip the RC29 or RC7 image file. Copy the DREAMIMG.nbh file to the SD card. (RC29 for US, RC7 is for UK)
3. Turn the device power off.
4. Hold Camera button, and press Power button to entry bootloader mode. You should see a gray/white screen with instructions to flash your phone with the update on your SD card. If you don't see that, make sure you followed the instructions properly.
5. As per the on-screen instructions, press the Power button to start upgrade procedure. DO NOT DO ANYTHING TO INTERRUPT THIS PROCESS.
6. After it is finished, perform the restart your phone.
then you can up date to RC30 then to RC33 manually or just wait for the
phone to get the updates on its own.
* Note *
If you do not know how, or why..... DO NOT PROCEED...
CBowley said:
* Note *
If you do not know how, or why..... DO NOT PROCEED...
Click to expand...
Click to collapse
perfect sense!
untermensch said:
you need to revert back to RC29, follow the instructions in this thread.
http://forum.xda-developers.com/showthread.php?t=442480
1. Format your phone's SD card to FAT32 mode:
* Hook your phone up to your computer using a USB cable and then wait for the notification to show up in your title bar of your phone.
* Click the notification, and then click "Mount".
* A new removable disk should show up on your computer. Right click it and select Format, and select FAT32 as the file system type.
2. Download and unzip the RC29 or RC7 image file. Copy the DREAMIMG.nbh file to the SD card. (RC29 for US, RC7 is for UK)
3. Turn the device power off.
4. Hold Camera button, and press Power button to entry bootloader mode. You should see a gray/white screen with instructions to flash your phone with the update on your SD card. If you don't see that, make sure you followed the instructions properly.
5. As per the on-screen instructions, press the Power button to start upgrade procedure. DO NOT DO ANYTHING TO INTERRUPT THIS PROCESS.
6. After it is finished, perform the restart your phone.
then you can up date to RC30 then to RC33 manually or just wait for the
phone to get the updates on its own.
Click to expand...
Click to collapse
is DREAIMG.NBH file NOT ---> DREAMIMG.nbh
I can not count how many times that file has been called dreamimg.nbh lol
May i ask a question about updating after returning to original firmware. Since we can only revert back to original UK version firmware and i got my phone in aussie, would i get back my stg firmware after updating to the newest firmware?
Hello Friends.
My English is not very good but let me indicate the beginning'll try to explain.
I bought the device from last year's TR TURKCELL un rom convert was 6.5.
My job, I had to return 6.5 to 6.1 sees. I tried to go back a lot of things but I think the name of the error RUU_signed.nbh file with the name change CHEEIMG.nbh want to install after the following issue has occurred.
How do I do if I've stayed if the bootloader. Now red, green, blue and white colors on the screen there. When a screen comes up gray. when I press the camera, restart button does bootloder screen.
On Screen
Palm TR
IPL-0.20
Palm TR
SPL-0.24 0000
Writes...
USB and PC hardware in the device is visible. Can not connect to the bootloader in the Active SYNC.
I researched the Internet to the device I need to take the original rom. A lot like the original Treo750_Cingular_ROM called Treo750_2.23_ROW_WM6 ROM file I tried did not take. As enhancements on a PC via USB, but does not do installation DesktopUpdater. I tried with SD card, makes installation , BOOT Ok GSM gives OK, but gives FAİL Errors on OS install. At the end of the installation gives the error bar. I'm normal with FAT32 formatted SD was snow. SD card would install the original file 1.16RWE_CHEEIMG.nbh. camera, I would hold the restart button. to install the device, while 1% is automatically rebooted. I also want to install the self-RADIO reboot is 7%.
As far as I understand with; device when large files at 1% at small-sized files when closing at 7% has been reopened
devicereset, Hard-SPL, Treo750_OS5_2_19199WWE_STD, Original 1.16RWE.nbh, Treo750_2_23_ROW_DE_DesktopUpdater, completefixed, I tried almost everything, but the installation does not do..
I need this device too. I am electronics technician. Heard called JTAG recovery method.
Luckily the apology, that I am open for any ideas. but you'll help me. Tek Tek at a descriptive writer, you'll be happy. I trust you. As of this minute to thank every one, wish to express my respect and greetings
Based on your bootloader screen you have not successfully HardSPL'd your Treo. You need to do that first, and then flashing ROMs with the SD card is possible. You can't flash a ROM using the SD card without doing this.
You also can't downgrade a ROM using the regular installation packages because the install package will see the current ROM (if I understand you correctly, WM6.5) is a newer ROM than what you are trying to install. I think I remember seeing a post someplace where you can edit one of the files in the installer package to get it to work, but you would have to search to find it and even so, it's probably much more difficult to do than just doing the Hard SPL.