Related
I used the rom cooking kitchen to make some of my favorite roms even better. Basically I just deleated some of the programs I dont use and deleated some of the extra sounds. Everything went through without any problems and now after I flashed it the smart mobility screen comes up and shows the radio and other info but then freezes there. How can I fix this or go back to a different rom? HELP. Thanks again
hollywood said:
I used the rom cooking kitchen to make some of my favorite roms even better. Basically I just deleated some of the programs I dont use and deleated some of the extra sounds. Everything went through without any problems and now after I flashed it the smart mobility screen comes up and shows the radio and other info but then freezes there. How can I fix this or go back to a different rom? HELP. Thanks again
Click to expand...
Click to collapse
try and get the ship rom that came with ya phone i had the same prob with a o2 xda/mda wizard i got the rom whitch was 1.05 ok now
hope this helps
How can I install it, my usb wont connect to the device?
hollywood said:
How can I install it, my usb wont connect to the device?
Click to expand...
Click to collapse
read the hard spl manual
*MICROSD FLASHING*
***IMPORTANT***
Please make sure you have HardSPL on your device.
1. Get a 128MB MicroSD card (or whatever size you like) and format it (***please make sure you format it, but not just delete all contents on it)
2. find the ROM image you would like to use, normally namede RUU_Sign.nbh, and rename it to "KAISIMG.nbh"
3. Plug the card into the phone, then enter boot loader mode by pressing down the Power and Camera buttons simultaneously, and using the stylus at the same time to press the RESET button at the left side. Continue pressing the two buttons for a few seconds after pressing and releasing the reset button until the bootloader screen appears. (taken from Wiki)
4. You will first see a tri-color screen then the information on the card. Press power button to start flashing.
5. After all these are done, press the reset button located at the bottom of the phone to reset the device.
Thank you very much, back to normal!
Today i installed the Ezinput 2.1 on my phone, so i reboot. Then i find my phone not booting which means hard reset. So i go on the bootloader and hard reset and it says something about no image. Then i rememeber something would of affect it probably the HTC Asian Characters Support i installed before which made the phone recognize i had a CHT ROM instead of a WWE ROM when you go to 'Device Info '. So hopefully some people who has experience to be kind enough to help me please. Thanks in advance.
[email protected]
You dont hard reset lyk that, your device thinks your trying to flash a rom image thats why its saying that
HOLD VOL DOWN, THE ROUND OK BUTTON AND PRESS THE RESET BUTTON
Hello, well, after several searching ended up here... my first post (like all of us when in trouble)
When trying to enter the tri-color screen, we pressed several times power+volume down and reset button but the phone never gets there, no matter what you do and now it is stuck at the "boot" screen that says: "Touch pro" in white letters and in the right down corner, with red letters says:
R 1.02.25.19
G 52.33.25.17W
D 1.94.00.00
Now, what to do here? it doesn´t boot, no hard reset, no nothing, if i press the reset button re-powers and gets there again... help..!!!
Thanks.
Sergio.
squiros1976 said:
Hello, well, after several searching ended up here... my first post (like all of us when in trouble)
When trying to enter the tri-color screen, we pressed several times power+volume down and reset button but the phone never gets there, no matter what you do and now it is stuck at the "boot" screen that says: "Touch pro" in white letters and in the right down corner, with red letters says:
R 1.02.25.19
G 52.33.25.17W
D 1.94.00.00
Now, what to do here? it doesn´t boot, no hard reset, no nothing, if i press the reset button re-powers and gets there again... help..!!!
Thanks.
Sergio.
Click to expand...
Click to collapse
Do entering bootloader : http://wiki.xda-developers.com/index.php?pagename=Raphael_For_Beginners#bootloader (With the device turned off, press and hold the VOLUME DOWN and POWER buttons, then press the RESET button with the stylus)
Then flash new ROM, i hope it's helping
Already tried that...
erwinpiero said:
Do entering bootloader :
(With the device turned off, press and hold the VOLUME DOWN and POWER buttons, then press the RESET button with the stylus)
Then flash new ROM, i hope it's helping
Click to expand...
Click to collapse
That´s exactly why i ended with the phone stuck at the first time... i recently got this phone and i wanted to see the bootloader version and stuff to do a firmware update but now it´s just there all the time. Not even being recognized by the pc.
Thanks.
Had You try flash via SD Card?
erwinpiero said:
Had You try flash via SD Card?
Click to expand...
Click to collapse
Well, no, i don´t have an sd card available now... one thing i forgot to say is the phone, after it is on that screen, never turns off again unless you remove the battery... and yes, i have left it on for a day, same thing...
What is the procedure to do the sd card flash thing? it that needs to get to the tree-color screen forget it... that´s exactly what the phone doesn´t do...
Thanks.
Sergio.
Hello Sir, to flash using SD card, you can read it here http://forum.xda-developers.com/showthread.php?t=448008 see number 5.
HTC Fuze
I had the same problem. None of the hard resets worked on my phone. The screen would be stuck on my lock screen and unresponsive. It would not shut off unless the battery was taken out.
Now it's working fine, all I had to do was press the reset button and enter in the code a1b2c3.
Hope this helps.
nessab04 said:
I had the same problem. None of the hard resets worked on my phone. The screen would be stuck on my lock screen and unresponsive. It would not shut off unless the battery was taken out.
Now it's working fine, all I had to do was press the reset button and enter in the code a1b2c3.
Hope this helps.
Click to expand...
Click to collapse
Hi,
Interesting... i´m not the only one with that problem then.... code doesn´t do anything... still same screen....
...no bootloader...
erwinpiero said:
Hello Sir, to flash using SD card, you can read it here --- see number 5.
Click to expand...
Click to collapse
Hello,
Ok, well, the main problem here is that i can´t get into bootloader... the phone is stuck at the fist "Touch pro" screen and nothing else happens...
Anyone with a clue on this? is this phone bricked then...
you sure youre puttin it into bootloader correctly? these things are pretty hard to brick, and can be put through hell and back and still be able to put into bootloader. make sure the hold VOLUME DOWN + POWER, and at the same time RESET WITH THE STYLUS IN THE BOTTOM...youll want to HOLD ALL THREE untill you see the tri colour bootloader screen. keep trying mate, it should go
Finally got bootloader...
the-wrangler said:
you sure youre puttin it into bootloader correctly? these things are pretty hard to brick, and can be put through hell and back and still be able to put into bootloader. make sure the hold VOLUME DOWN + POWER, and at the same time RESET WITH THE STYLUS IN THE BOTTOM...youll want to HOLD ALL THREE untill you see the tri colour bootloader screen. keep trying mate, it should go
Click to expand...
Click to collapse
Finally, after several tries it got into bootloader... now the thing doesn't end here because for some reason when i try to upload the Raphael Hard_SPL the phone goes ok to 0% and in about a minute a communication error appears and that's it...
We are moving forward... at least.
Bootloader Info.
Tried to flash via microSD but the phone says not allow..i guess that's because the hard SPL is not installed and it has the stock... here's what the bootloader shows, i'm not being able to install olinex hardSPL...
RAPH100
SPL-1.94.0000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
PCBID 0x80
RID 0x0
ideas?
...no way to flash it back....
so... i guess there´s no way to get this back into business... when trying to flash always reports communication error at 0%...
You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.
Farmer Ted said:
You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.
Click to expand...
Click to collapse
ya i just noticed the RAPH100 in his info he posted and the t7272 in the header..mines a RAPH800 and bootloader HAS to have vol + power..anyway, i remember having an issue with something similar with my old vogue..have you tried flashing the shipped stock rom back on? if not, try flashing the stock back on it and if it goes, then try the unlock afterwards. dont fret bud, someone here will get you sorted out
here, i found this as im not well versed in raph100s. its a chart with raph100 roms. im sure some must be shipped stock roms and may be worth a try. sorry i couldnt help more, like i said hopefully someone who knows your device better may be able to help
http://wiki.xda-developers.com/index.php?pagename=HTC_Raphael_WM6.1_ROMs
How about flashing official ROM via microSD card?
patrick_spd4u said:
How about flashing official ROM via microSD card?
Click to expand...
Click to collapse
Download the official rom, right click on the exe and extract it somewhere, you'll get several files, rename RUU_signed.nbh to raphimg.nbh, move it to the root of your sd card and you should be able to install it. It should contain splash screen, radio and os.
No way to flash HardSPL...
Hello, thank you for your help! in fact the volume down+reset works perfect to get into bootloader but every time i try to flash hardSPL or stock rom via USB it says "communication error" and the phone displays a 0% bar...
Windows7 is detecting it as HTC USB Sync.
Thanks..
Farmer Ted said:
You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.
Click to expand...
Click to collapse
...will try it again...
Hi
In fact the most close to the rom i had on that cell is ruu_signed_1.90.401.1_wwe, downloaded it and will try it again later using sdcard... one thing i wonder is the SPL version which is 1.94.00.00 on my phone.
Sergio.
freakzone said:
Download the official rom, right click on the exe and extract it somewhere, you'll get several files, rename RUU_signed.nbh to raphimg.nbh, move it to the root of your sd card and you should be able to install it. It should contain splash screen, radio and os.
Click to expand...
Click to collapse
Hi all,
after installing volDeus BG tweakv 0.5 my phone died. i can't restart it and i can't perform a hard reset. i also tried the red reset button from the back - nothing. it's not even charging. i tried a different battery but didn't solve the problem. any help would be appreciated. i don't want to send it back for repair.
It happened to me after manilla, i made this factory reset and after that the phone worked fine.
Performing a factory reset using phone buttons
If you cannot turn on your phone or access the phone settings, you can still perform a factory reset by using buttons on the phone.
With your phone powered off, press and hold the VOLUME UP and VOLUME DOWN buttons.
While holding the volume buttons, press the END/POWER button briefly and then release it.
When you see a warning message on screen, release the VOLUME UP and VOLUME DOWN buttons.
Press the VOLUME UP button to perform the reset, or press any other button to cancel the reset.
thanks for reply. like i said, i can't perform a hard reset because the phone is not responding. when i press the volume up, down and power button nothing happens. i don't know what to do.
Ahhhhhh.. me 2
My hd was dead during flashing and still not working but a good thing......
I bought a new HD2.
But if some one have an idea plz let me know.
Thanks in advance
l3onard said:
thanks for reply. like i said, i can't perform a hard reset because the phone is not responding. when i press the volume up, down and power button nothing happens. i don't know what to do.
Click to expand...
Click to collapse
If you're unable to perform a hard reset with the hard keys as explained above, you don't have any other choice but to send it in for repair as far as I know...sorry.
I'd suggest first taking out the battery for a couple of hours and then try again.
de Wolfe said:
I'd suggest first taking out the battery for a couple of hours and then try again.
Click to expand...
Click to collapse
i'll try this. thanks.
de Wolfe said:
I'd suggest first taking out the battery for a couple of hours and then try again.
Click to expand...
Click to collapse
l3onard said:
i'll try this. thanks.
Click to expand...
Click to collapse
Also try this;
1. Remove the battery
2. Plug the USB cable to your computer and to your HD2
3. Push and hold volume down/up
4. Insert the battery
Normally the HD2 would start when doing this.
wardh said:
Also try this;
1. Remove the battery
2. Plug the USB cable to your computer and to your HD2
3. Push and hold volume down/up
4. Insert the battery
Normally the HD2 would start when doing this.
Click to expand...
Click to collapse
thanks but it's not working. maybe because i deactivated charging when connected to PC.
with the combination volume -, reset and power i managed to enter the bootloader. anybody help me to go on pls?
l3onard said:
with the combination volume -, reset and power i managed to enter the bootloader. anybody help me to go on pls?
Click to expand...
Click to collapse
1. L3nny, for future reference, Co0kie's Home Tab v1.8.5 already has the voldeus skinning function built-in, so there's no more need for it in the future... but since you've got it now... calm down and bear with me here...
2. Voldeus' skinning does not mess with your rom image at all, and any changes can be reversed with a HardReset (i've been there and done that). A HardReset does take 3 hands and a few tries to get it for the first time. The red button on the back is only a SoftReset, same as taking the battery out, so that's not gonna work. And since you've just seen the bootloader now, your previous HardReset attempt probably didn't have the correct buttons combination, so it never worked. Try again using this combo from TBoy2000's HowTo thread: remember it's pressing volumeUP AND Down together AND Power button. you need three thumbs
tboy2000 said:
1. With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
2. Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see this message on the screen:
"This operation will delete all your personal data, and reset all settings to the manufacturer default settings. Press VolUp to restore manufacturer defaults, or press other keys to cancel."
3. Release the VOLUME UP and VOLUME DOWN buttons.
4. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
Click to expand...
Click to collapse
good luck
atlaswing said:
1. L3nny, for future reference, Co0kie's Home Tab v1.8.5 already has the voldeus skinning function built-in, so there's no more need for it in the future... but since you've got it now... calm down and bear with me here...
2. Voldeus' skinning does not mess with your rom image at all, and any changes can be reversed with a HardReset (i've been there and done that). A HardReset does take 3 hands and a few tries to get it for the first time. The red button on the back is only a SoftReset, same as taking the battery out, so that's not gonna work. And since you've just seen the bootloader now, your previous HardReset attempt probably didn't have the correct buttons combination, so it never worked. Try again using this combo from TBoy2000's HowTo thread: remember it's pressing volumeUP AND Down together AND Power button. you need three thumbs
good luck
Click to expand...
Click to collapse
hard reset is not working. i don't think i do it wrong, because it's not the first time i try this.
i copied shell32.exe and aygshell.dll from voldeus' post an dput it on my sd card. i chose some settings, chose the wallpaper and soft reset. but the phone froze at start-up. i put out the battery and from that moment, i couldn't do anything.
if i can enter the bootloader does it mean i can install HSPL and maybe a stock or custom ROM? but if something goes wrong i loose my warranty!
please help me guys, i'm lost.
1) Maby your battery charge is too low ( maby, your usb port is broken and charging is not ON)
Try to connect your HD2 to charge
Its will be better if you will go to service centre.
sorry for my bad English
l3onard said:
hard reset is not working. i don't think i do it wrong, because it's not the first time i try this.
i copied shell32.exe and aygshell.dll from voldeus' post an dput it on my sd card. i chose some settings, chose the wallpaper and soft reset. but the phone froze at start-up. i put out the battery and from that moment, i couldn't do anything.
if i can enter the bootloader does it mean i can install HSPL and maybe a stock or custom ROM? but if something goes wrong i loose my warranty!
please help me guys, i'm lost.
Click to expand...
Click to collapse
Is your machine tied to a certain provider? If it is send it back and get a new one.You obviously have a faulty machine.Easy way to bootloader,
Hold volume down.
Take off back.
Press red button.
Bootloader appears flash radio or ROM
i tried with another battery and nothing changed. so i solved this problem already.
yes, it's an orange phone. what would be better: trying to flash a new ROM (if something go wrong i loose the warranty) or send it back for repair?
l3onard said:
i tried with another battery and nothing changed. so i solved this problem already.
yes, it's an orange phone. what would be better: trying to flash a new ROM (if something go wrong i loose the warranty) or send it back for repair?
Click to expand...
Click to collapse
New phone definitely.
l3onard said:
i tried with another battery and nothing changed. so i solved this problem already.
yes, it's an orange phone. what would be better: trying to flash a new ROM (if something go wrong i loose the warranty) or send it back for repair?
Click to expand...
Click to collapse
I dont know but i think that: to flash a new ROM you must enter in bootloader.
It is better to change a device for the new
Its a critical problem. This problem can appear again even if you repair your phone.
If you have official guarantee - you must change your device ( go to your service centre )
DUDE!~!!!!~! You're already in bootloader, just flash your original orange STOCK ROM already and be done with this!!! ALSO, you MUST take out your SD card, since that maybe the problem to begin with (having your core system files at the root of your SD is not a smart idea). If that DOESN'T work, then send the damn thing back to Orange for an exchange! Your choices are really simple, why are you wasting everone's time with this!
Good luck
i just wanted your opinion about my problem beeing a beginner in WM phones. i think always is better to ask a second opinion, especially when you are a newbie. if i wasted someones time i'm sorry.
anyway, thanks for the answers. i'll send it back to orange.
I wouldn't send the phone to repair.
1. enter bootloader-mode
2. mtty task29 search forum
3. enter bootloader again
4. flash orange original rom
5. after flashing perform a hard reset
Hi everyone,
i have a Haipai X720D, and after few errors i've make, i decided to reinstall it
i have download an flash it with http://forum.xda-developers.com/showpost.php?p=36025676&postcount=4
but my phone won't boot anymore, and i cannot connect it to the computeur
i think i've heard a method like pushing the volume+ button while power it on but i can't find it...
any help would be appreciate
up
- If you hold down HOME button + POWER button + volume UP button you will get into Recovery Mode.
- If you hold down HOME button + POWER button + volume DOWN button you will get into Download Mode.
If you want to flash a customROM go into Recovery mode, there you can find something like MOUNT USB or MOUNT SD. If you do that you will be able to connect to your computer.
When you're connected you can kopie your custom ROM .ZIP file into your Internal SD card after downloading it. If you did that you go back to Recovery Mode. There you can choose instal ZIP from SD card. Instal your previous downloaded .ZIP file from your customROM and there ya go.
Thanks for the help i will try tonight.
but home button is sensitive, it's not a physical button, i hope it will work !
hi,
whatever i try, my phone is'nt detected ....
i heard about a solution, by removing the screw, see :
http://forum.xda-developers.com/showpost.php?p=37014952&postcount=6
can someone explain me the secondn sentence
"2 - with a piece of wire to ground the point KCOLD connecting to a screw of the case"
thanks for the help
Nitrogin said:
hi,
whatever i try, my phone is'nt detected ....
i heard about a solution, by removing the screw, see :
http://forum.xda-developers.com/showpost.php?p=37014952&postcount=6
can someone explain me the secondn sentence
"2 - with a piece of wire to ground the point KCOLD connecting to a screw of the case"
thanks for the help
Click to expand...
Click to collapse
hello
can you tell me where is the point KCOLD? i have the same problem on my X720D.:highfive: