I have an HTC Touch Cruise. The first problem occurred when I dialed into a system with a touch tone menu. For some reason I couldn't access the menus. It was working fine earlier in the day.
Now it cant even dial out, the phone makes the tones, I hit send and its just blank. Also, when someone calls the phone will ring, I can hit answer but I can't hear them and they can't hear me.
I am on my home network, I have lots of bars, etc.
I have tried a soft reset and even a hard reset.. same deal. I also tried changing settings in the registry for DTMF HKLM,"Drivers\BuiltIn\RIL","EnableDTMFSupport" I have changed it to 0 and back to 1... neither setting works.
Thanks,
P
Related
Is there a setting to silence the phone on an incoming call when the phone is locked? Pressing the volume up or down WON'T work with me.
Thanks in advance.
i just tried on my phone several times from different numbers and it works fine for me.. both buttons too
Were you using any program such as manic AutoKeylock? or you just held the end call button to lock it?
Maybe I need to reset it but I didn't install any programs.
just end button i did not think i needed a program to autolock my phone
silence
Hi,
when somebody calls me i would like to silence the ringtone and not hangup. (on sonyericsson you press the side key for volume)
pressing volume up or down doesn't work for me either. is there a place in settings where you have to enable this feature? (i sure couldn't find it )
I would like to confirm that a hard reset fixed the problem! Pressing volume down while phone is locked SHOULD silence the phone by default.
Could be some software glitch that messed it up in the first place.
Figured out the problem. It seems to me that when there is an active connection, i.e EDGE is connected and it is showing in the near the cell signal, you WON'T be able to silence it by pressing a volume down.
If you go to connection manager and disconnect Edge by pressing 6, then lock it and let somebody call you, you WILL be able to silence it!
I have tried the above three times to confirm it. Seems pretty messed up if you ask me!
If you know how to solve the problem, please let me know.
Anybody figured out the problem (Read above)? I will paypal you $20 if you can get this to work!
Really, why did they mess it up like that when my previous phone, SDA, worked!
It's a very strange problem.
After upgrading to wm6, when I started a call on the today screen appeared a "full screen" notification from where I could activate the loud-speaker or mute the call. Then I tryed to install a .cab to emulate the htc touch style. From that moment, when I start a call the past "full screen" notification area does not appear any more, so I have to enter the menu to mute the call or activate the loud-speaker. I removed the application but nothing changed. Then I hard-resetted the treo 750v, and the problem was solved, but when I launched the restore of my spb backup of yesterday, the today palm application desappeared again
I think it's a stupid registry value, but I don't know which value to change, could someone help me?
There is no installed application and no today plugin activated.
Thanks in advance and excuse my poor english.
I too also share the same problem, I installed WM6, and then I thought i try to use the HTC home today plugin to make my phone look a bit nicer, problem was it made it look kinda stupid. I couldnt use the phone number lookup field on the today screen as the HTC today took up all the space, also I noticed that when I place a call, the phone connection screen and the screen that stays on showing the duration and the mute and loudspeaker options had been removed . The best thing I could think of at the time was just to uninstall the plugin for HTC Home, however that didnt resolve the problem, I know the person who posted here before mentioned that you can fix this problem with a hard dreset, but is there any other alnernative method as I am fed up of resetting this device now.
Please help me!
Cheers guys.
The Fagla Bahstar
Similar problems here. Had to hard reset as my power button would not work at all. The hard reset was the only way I could fix it...
Does nobody knows the registry key to change?
Yea i am having the same problem. I wish i didn't try the htc home. Any fix for this?
I really don't want to hard resert my phone. Its got to be in the registry.
Someone has to have an solution? I tried looking, but maybe someone who knows the phone a bit more in depth, can help.
try this thread.
info on how to get HTC home to work properly.
http://forum.xda-developers.com/showthread.php?t=355198
i'm looking for a way to have the touchscreen on my smartphone disabled when a call comes in. I usualy have the phone in my pocket. When a call comes in and i'm taking the phone out my pocket, i accidentely touch the screen. And that's mostly not in the "accept" spot off the screen
So i would like to accept or decline the call by pressing the hardware keys only with the touchscreen disabled.
Been searching the forums and googled my way over the internet. Without luck so far.
Any ideas?
regards, Jeen
S2U2 uses a slide to answer feature, very nice.
Installed s2u2 and it sure looked great... until the first soft reset (after nightly backup). After the soft reset the phone freezes every time a call comes in, having to soft reset again. Whenever a call comes in (when phone is locked or switched off) the normal s2u2 lock screen pops up without the call notification and that's it. Phone freezes and soft or hardware keys don't work anymore.
I even uninstalled SPB Mobile Shell to see if that was conflicting with s2u2. No luck.
Couldn't get rid of this problem so i uninstalled s2u2. Shame, i liked it...
Any other options to answer my original question?
regards Jeen
Hello,
My LG GM750 (with stock WM6.5) doesn't ring anymore, nor does it vibrate when set to "ring and vibrate" - it vibrates though when I set it to vibrate only. Reminders don't ring/vibrate either. G-alarm pops up an error message that the sound file cannot be played. WMPlayer does not even start. When I try to make settings in Wireless Manager / Phone Settings, the OK button in the corner of the screen does not work (the settings window just stays on the screen).
During phone calls everything is ok and other applications can play sounds.
I have installed quite a lot of applications, but everything worked just fine for at least one month, then it suddenly stopped ringing: G-Alarm, SPB Mobile Shell, mRing, S2U2 (with caller ID) etc.
The same problem happened to me some time ago and the only way I could fix it was by doing a hard reset (soft reset is useless).
Any ideas on how would I be able to fix it this time without performing a hard reset and taking it all over from the beginning and hoping it will not happen again?
Thank you!
hi,
sorry for this lengthy message. But pls, experts look into this.
my father was having an Imate jama 201. 3 yrs ago, he kept inside since it did not work properly for him. That time i did not know what the problem was. Now i have caught hold of that.
The phone switches on properly. The welcome screen is seen. If there is no Sim card, it displays a msg. When i put a Sim card, it displays the operator name as well as the G- GPRS symbol. But when i click the start button or any key, it operates very very slowly.
In the navigation buttons i can only press the down button to go down a menu, but that too, by pressing the left key along with it. The right selection button( long rectangle near back button,) does not respond when i click it. But if the phone back light goes out, the phone responds back by coming back again to the home screen, on clicking that button.
I dont know whether this is a software or a hardware problem. The phone, very rarely is able to work without any sluggishness. I am able to view the preloaded gifs and images in the pictures menu and even go to camera mode.
I am able to receive calls and messages, but since the buttons don't respond properly, i am not able to answer them. The ring tone is loud enough to hear when i get a call.
I have no important data in it, so i am willing to flash it irrespective of any data loss, if required.
I am ready to answer any of your queries regarding this issue.
Thanks in Advance
You should try to make a hard-reset!
actually, most of the keys in it wont work properly. You just press randomly some keys in it, only a letter appears. i am able to go till the hard reset menu, but not able to enter the number: 1234