Greetings all!
I was wondering if anyone knows the solution to my problem.
When i try to access live messenger or the weather update on my TP through 3G i get the connection error. When using it through WiFi it updates in less than 5 seconds.
Anyone know of any prossible solutions?
Thanks in advance
I had the very same problem, but it actually disappeared after a weeks use.
I really didn't do anything to solve it.
I have the same problem with my TD2.
Same here, works when I first soft reset but say a hour or two later it does not connect it says cannot connect to wap.cingular.com try again at a later time.
If you are on AT&T your settings should be as such;
Go to Settings\Connections\Connections, click on "Advanced" and "Select Networks", in the drop down boxes, set both to MediaNet and "X" out of there.
Go back to the Tasks tab and select "Manage Existing Connections" then click "Proxy Settings". Make sure that "This network connects to the internet" is selected and "Uses a proxy" is unselected.
Also clear out any proxy servers already listed.
You should be all set.
Related
I previously posted a question, but received no replies. Just wondered if anyone can now help me. There is wi-fi at work which I am able to connect to. However, whenever I do so, the 3G, GPRS takes over and connects that way. I cannot understand why or get around it. I am on o2. My colleague is on T mobile - I set his wi-fi link up in exactly the same way and he has no problems whatsoever. I am desperate for your suggestions.
Are you using push mail by chance? I found that M$ push will try to connect to GPRS even when WiFI connection is established. IE goes through the WiFi connection (obvious speed difference) but push mail won't let me kill GPRS.
Haven't found any solution to this yet.
Any chance you have tried turning the radio off!! Of course you wont be able to receive/make calls)
Just a suggestion though
I had same problem but managed to solve it (I have a Qtek9100 a.k.a Wizard with WM 5.0)
You must go to "Settings", select the "Connections" tab bellow and the click on the "Connections" icon. Once there you must select the "Advanced" tab bellow and click "Select Networks" button where you'll find a drop-down (combo) box responsible for the programs that automatically connect to the Internet.
You'll probably find there the connections you set for the GPRS and MMS. All you need to do is create a new one (can call Wifi or whatever) and select it.
That's it. hope you can do it
I have a Cingular 8525 with WM5, using the lastest version of Activesync. I do not have wifi or 3g internet connection on my cell phone. Everything is synced and seems to be working fine but PIE doesn't work.
My Network management settings are:
Programs that automatically connect to the Internet should connect using: "My ISP"
Programs that automatically connect to a private network should connect using: "My ISP"
Under Connections it reads: My ISP, and for select a modem it says "Cellular Line"
How do I enable my phone to use pocket internet explorer when cradled? The reason is that my RSS reader cannot update because IE cannot connect.
Save me! I spent the last 4 hours trying to fix this problem.
Hi,
I had the same problem some time ago.
In ActiveSync\File\Connections I had to tick "This computer is connected to: The internet". Now it works.
xunkn0vvnx said:
I have a Cingular 8525 with WM5, using the lastest version of Activesync. I do not have wifi or 3g internet connection on my cell phone. Everything is synced and seems to be working fine but PIE doesn't work.
My Network management settings are:
Programs that automatically connect to the Internet should connect using: "My ISP"
Programs that automatically connect to a private network should connect using: "My ISP"
Under Connections it reads: My ISP, and for select a modem it says "Cellular Line"
How do I enable my phone to use pocket internet explorer when cradled? The reason is that my RSS reader cannot update because IE cannot connect.
Save me! I spent the last 4 hours trying to fix this problem.
Click to expand...
Click to collapse
Change "cellular line" to "cellular line GPRS" from the scroll down box.
The saga still continues to no avail...
i clicked "This computer is connected to the internet"
and also selected "Cellular line GPRS"
What do I enter for Access point name, username, password, etc.
This is getting really annoying.
xunkn0vvnx said:
The saga still continues to no avail...
i clicked "This computer is connected to the internet"
and also selected "Cellular line GPRS"
What do I enter for Access point name, username, password, etc.
This is getting really annoying.
Click to expand...
Click to collapse
Follow the screen shots in order 1-4. access point: wap.cingular(lower case) User: [email protected](all caps) Password: CINGULAR1 (all caps)
8125
2.25.11.1
Still nothing, when I right click and try to connect it says
"Cannot Connect
The current connection cannot be used for your request. Please end the current connection and try again."
xunkn0vvnx said:
Still nothing, when I right click and try to connect it says
"Cannot Connect
The current connection cannot be used for your request. Please end the current connection and try again."
Click to expand...
Click to collapse
Is AT&T your carrier? When did all this begin happening? The settings I've given you are to be made directly on your device, and not from a PC. Try "auto pick" instead of ISP GPRS, and see if that helps.
hotdog53 said:
Is AT&T your carrier? When did all this begin happening? The settings I've given you are to be made directly on your device, and not from a PC. Try "auto pick" instead of ISP GPRS, and see if that helps.
Click to expand...
Click to collapse
One more thing to try: go to your connections settings, tap on advanced (at bottom) select MediaNet from scroll box, tap "proxy" the box that says it uses a proxy to connect should be unchecked (empty) The top box should be checked. You haven't done any internet connection tweaks in the registry have you?
0 internet registry tweaks, do you think you could link me to the cab that should be able to fix this for me?
Either way, and despite whether or not this gets fixed, thank you, thank you, for helping me.
xunkn0vvnx said:
0 internet registry tweaks, do you think you could link me to the cab that should be able to fix this for me?
Either way, and despite whether or not this gets fixed, thank you, thank you, for helping me.
Click to expand...
Click to collapse
Sorry man, I don't have the cabs for this fix. I remember reading about someone having the same problems and a cab fix was requested. Can't remember where I read about it. I recommend a forum or google search for the cab fix...I'm pretty sure you'll find what you need.
Ok here is the weird thing... I am running SPB mobile, and when I sync my weather is able to update for New York, NY. Doesn't that mean it must be getting an internet connection through PIE? DOes SPB mobile mess with the registry?
Anybody? Lately I've been using WiFi to update my phone but Id rather have it work when it is cradled.
any reason why the above should not work "out of the box". i have been tethering fine with my BJ1 but got my FUZE yesterday and it's not working. Says "waiting for network" then "remote party has ended this connection".
i did try installing the modem drivers from the CD, did not help.
what is the most common cause of ICS not working with vista over USB?
thanks in advance.
did you uncheck enable advanced network functionality? Its checked as defualt. Uncheck it and try again.
more ICS help needed
hondaguyjoe said:
did you uncheck enable advanced network functionality? Its checked as defualt. Uncheck it and try again.
Click to expand...
Click to collapse
i tried that, still does not work.
in VISTA i briefly see the RNDIS network connection go to enabled but quickly goes to disabled when the handset says "remote party has ended..."
on the FUZE i have
Settings | Connections | Wireless Manager | Data Connection = On
and the only thing i changed during my trouble shooting is
Media Net | Select a Modem = Cellular Line (GPRS, 3G)
settings also have wap.cingular as it should, and don't know what the preset password is - i haven't touched it. should i use the password that i know worked on the BJ1?
also, in WiFi Settings, does the Remote NDIS network adapter settings play into this? i put it on DHCP and it also says "connect to work" - should that be "internet"?
thanks
raywright1 said:
i tried that, still does not work.
in VISTA i briefly see the RNDIS network connection go to enabled but quickly goes to disabled when the handset says "remote party has ended..."
on the FUZE i have
Settings | Connections | Wireless Manager | Data Connection = On
and the only thing i changed during my trouble shooting is
Media Net | Select a Modem = Cellular Line (GPRS, 3G)
settings also have wap.cingular as it should, and don't know what the preset password is - i haven't touched it. should i use the password that i know worked on the BJ1?
also, in WiFi Settings, does the Remote NDIS network adapter settings play into this? i put it on DHCP and it also says "connect to work" - should that be "internet"?
thanks
Click to expand...
Click to collapse
Ok Im having the same problem I guess I should of tried it before opening my mouth lol
on my 8525 running WM6.1 it works flawlessly PC connection is set to usb and network connection is to media net.
On the fuze I get the same error you do something like connecton to host failed....
so now I'm on the please help me list with you!
I spoke to someone a rep friend of mine and he said they disabled the ability to tether. You need to have the tethering plan in order for it to work.
Hmm, seems like somebody's going to need to hack around that
jasongw said:
Hmm, seems like somebody's going to need to hack around that
Click to expand...
Click to collapse
Yeah really! looks like I wont be getting rid of my tytn any time soon its going to suck to swap out sims everytime I want to tether to my laptop.
I had a similar issue:
An unlocked and custom-ROM Wizard worked with ICS just fine. My new Samsung Epix kept spitting out the dreaded "The remote party has ended this connection" almost immediately upon clicking Connect in ICS.
I see you already have MediaNET pointed to wap.cingular
I found I had to add the username and password:
[email protected]
CINGULAR1
I also set GPRS Authentication for MediaNET to CHAP.
I am internet sharing 3G beautifully over Bluetooth with Vista64.
ICS problems (cont'd)
cjones277 said:
I had a similar issue:
MediaNET pointed to wap.cingular
[email protected]
CINGULAR1
GPRS Authentication for MediaNET to CHAP.
Click to expand...
Click to collapse
this is consistent with my BJ1 settings and works fine on that device. i have the same settings on the fuze.
did you do anything on the Vista side?
did you have to install the drivers from the CD?
any other settings that i should know about?
I had the same problem. This workaround seems to be working for me, though:
0. Make sure phone is NOT connected to computer
1. Go to Start -> Programs -> Internet Sharing
2. Set the PC Connection to USB and the Network Connection to Media Net
3. Click Connect
4. Connect USB cable to computer
ITNV said:
I had the same problem. This workaround seems to be working for me, though:
0. Make sure phone is NOT connected to computer
1. Go to Start -> Programs -> Internet Sharing
2. Set the PC Connection to USB and the Network Connection to Media Net
3. Click Connect
4. Connect USB cable to computer
Click to expand...
Click to collapse
This is what I do on my 8525 but on the fuze no luck :-(
Im going to try and do a hard reset and stop it from installing the at&t stuff and see if it works.
ITNV said:
I had the same problem. This workaround seems to be working for me, though:
0. Make sure phone is NOT connected to computer
1. Go to Start -> Programs -> Internet Sharing
2. Set the PC Connection to USB and the Network Connection to Media Net
3. Click Connect
4. Connect USB cable to computer
Click to expand...
Click to collapse
Network connection drop down seems to be absent in internet sharing on my Fuze... hmmm...
Well the hard reset with no extra stuff installed did not work :-(
I hope some HTC wizard can figure this out.
I think this is a Windows Mobile registry settings issue, not an HTC issue. They set it this way at the request of AT&T.
Got this from:
http://forum.xda-developers.com/showthread.php?t=437796&page=2
This may actually fix both the missing Network drop-down and the "Remote party has ended the connection" issue. Its for Sprint, but worked for me. Just substitute MediaNET for Sprint.
After my first post, I had to do a Hard Reset and then the issue jamorgan2008 is having (Network drop-down not showing). I didn't have this the first time. I looked up the Registry Key and it had Cingular ISP as the ForceCellConnection value. I deleted it and am back on again. As such, this may also fix your issue as well, hondaguyjoe. Do you have the Network option in Internet Sharing or just PC Connection? You may need a Mobile Registry Editor for this.
See below:
Originally Posted by mcgowanbl View Post
This works with standard $15/month Sprint PCS Vision plan.
No you do not need to purchase Phone As Modem plan.
No they will not charge you extra because there's no way for them to known you tethering to a pc.
I have two Touch Diamonds (not Pro's).
One for my wife and one for me.
My Internet sharing (Start\Programs\Internet sharing) only has one drop down menu, "PC Connection".
My wife's has two drop downs "PC Connection" AND "Network connection".
Now I bought her's two days after mine at the same Sprint store.
Her Internet connection shares Internet via USB connected directly to a PC without issue.
Mine doesn't since I have not been able to set the missing "Network connection" drop down menu option to the appropriate setting of "Sprint". Instead it either say Waiting for network or error 67 invalid username and password (something like that)
I deleted the key: (not just the value)
[HKEY_LOCAL_MACHINE\Comm\InternetSharing\settings]
ForceCellConnection
Now I got the second drop down menu "Network connection", restarted the phone and now it works like a champ.
cjones277 said:
I think this is a Windows Mobile registry settings issue, not an HTC issue. They set it this way at the request of AT&T.
Got this from:
http://forum.xda-developers.com/showthread.php?t=437796&page=2
This may actually fix both the missing Network drop-down and the "Remote party has ended the connection" issue. Its for Sprint, but worked for me. Just substitute MediaNET for Sprint.
After my first post, I had to do a Hard Reset and then the issue jamorgan2008 is having (Network drop-down not showing). I didn't have this the first time. I looked up the Registry Key and it had Cingular ISP as the ForceCellConnection value. I deleted it and am back on again. As such, this may also fix your issue as well, hondaguyjoe. Do you have the Network option in Internet Sharing or just PC Connection? You may need a Mobile Registry Editor for this.
See below:
Originally Posted by mcgowanbl View Post
This works with standard $15/month Sprint PCS Vision plan.
No you do not need to purchase Phone As Modem plan.
No they will not charge you extra because there's no way for them to known you tethering to a pc.
I have two Touch Diamonds (not Pro's).
One for my wife and one for me.
My Internet sharing (Start\Programs\Internet sharing) only has one drop down menu, "PC Connection".
My wife's has two drop downs "PC Connection" AND "Network connection".
Now I bought her's two days after mine at the same Sprint store.
Her Internet connection shares Internet via USB connected directly to a PC without issue.
Mine doesn't since I have not been able to set the missing "Network connection" drop down menu option to the appropriate setting of "Sprint". Instead it either say Waiting for network or error 67 invalid username and password (something like that)
I deleted the key: (not just the value)
[HKEY_LOCAL_MACHINE\Comm\InternetSharing\settings]
ForceCellConnection
Now I got the second drop down menu "Network connection", restarted the phone and now it works like a champ.
Click to expand...
Click to collapse
Works great!!! Posting now from my MBP via Fuze!
Sweet thanks this board is great!! *sent from my note book via fuze"
New issue I have the 3G icon with 2 bars but when I connect to the notebook it switches to edge. I can browse on the device with 3G but once I press connect it goes to edge.
Any ideas?
Thanks
hondaguyjoe said:
New issue I have the 3G icon with 2 bars but when I connect to the notebook it switches to edge. I can browse on the device with 3G but once I press connect it goes to edge.
Any ideas?
Thanks
Click to expand...
Click to collapse
Im not seeing this issue with bluetooth... perhaps you are in a poor reception area. Are you using a usb cable or bluetooth?
What are you using to edit the registry with?
Arius1 said:
What are you using to edit the registry with?
Click to expand...
Click to collapse
Search Google for PHM Registry Editor.
I have the Fuze version on at&t network. I've disabled 3G on AT&T's side so there is no way to connect through there.
Nevertheless, my phone ALWAYS tries to connect to the 3G network and i've disabled 3G connections using Nodata.cab, advancedconfig, diamondtweaks.
Still, the warning signs always come up:
"there is a problem connecting to the gprs service in your registered home network warning"
and this occurs, when I turn on the phone and many other times.
Is there a way to disable this warning? I know I cant connect, its because i disabled it!!!!
anyone? it comes up like 50x a day andi have to click OK to make it go away every single time
Have you unchecked the auto update setting for the weather program? Doing this worked for me.
did that, but didnt fix the problem. anything else that can be auto updating or trying to contact the 3G network?
Go to start -- settings -- connections -- connections --advanced -- select network.
Here I think you can change the defaults so that when ever a program tries to use internet it will either use wifi (if available) or nothing....
I have blocked the wireless internet access on all my lines and this is how I solved the problem of getting gprs disconnect warnings.
Hope this helps.
Is it possible to just disable this warning?
I'm switching between my personal and business SIM cards quite often, and I have the data connection disabled on the business card, while on personal I have a data plan, so I want to be always-online.
I disabled aGPS and now i dont get the warning as much. (remember, i disabled GPRS from att side).
when i start my phone, i get 1 warning (i used to get 3?)
maybe i'm on the right track...
But the point is not to disable features so they don't auto-connect to the Internet.
The point is for the OS to try to onnect automatically, but when it failes - it doesn't have to scream that to your face every 5 minutes.
I'm bumping this thread cause I did the same thing and want to know how to disable the message as well.
still no answer to this
Translating from Dutch, so bear with me:
Go to Personal > phone > network settings and put the band on GSM.
Note that you won't be able to use the 3G + H data connections then.
my father has the same problem on his Diamond, need help!
bump, i have the same problem as well
any solutions?
i have a solution.
download > install > and run NOGPRS.cab aka No Data. that will shut it up. i just had the same problem and i did that and now i havnt gotten any... i think i might get like one if i turn the phone on and off and what not, but other then that its fine.
Solution to GPRS warning message
Go to settings > Connections > Connections > advanced > select networks >
now check both options to 'my work network'
click ok
and reboot
the irritating message will go away.
until you again reinstall the sim into your phone and it will automatically reconfigure the settings.
Just repeat the above process.
solution
1. Tap Start.
2. Tap Settings.
3. Tap Phone.
4. Tap the Network Tab.
5. Tap the Network Selection Drop down.
6. Tap Manual.
7. Tap the desired network.
8. Tap Ok.
.. So every time I reboot it wants to take me to the connection settings (I've already set up my GPRS/3G and it works fine), and the phone always thinks I'm roaming.
Also, according to my providers webpage (It's Simyo in Spain) they keep sending me config SMS's but they don't seem to be received.
Can anyone help? Thanks
By the way I have Googled this and found lots of references to the connection wizard but I can't find it. If I go to settings -> connections -> connections, then I just get "Simyo" with 'add connection' and 'manage connections' below it, and a similar set of links for 'my work connection'
Never mind, I found the connection setup, it just wasn't showing in the settings menu of Bell UI.
Sorry, I'll mark this solved now.
[edit: Oh I can't change the thread title...]