Was asked to re-post in upgrading and wm6
I had my 8125 flash a bad rom and was stuck on splash screen.
fixed it with mtty1.42
connect in bootloader mode with usb
choose usb connection not com1, or com2
you will get a white screen press enter
then you see cmd>
type format will show you what you can format
you want to format the os part starts with a b cant remember exactly
once its formated flash a rom and you should be good to go if you have any questions just let me know.
Related
My qtek after a reset always go to the bootloader screen (USB v1.0).
I have to take off the battery and wait for a few seconds to power it up again, but it always start as i've done a hard reset.
When it starts again, i have to align the screen, and when it is installing the ext rom, it goes to the bootloader screen AGAIN!!!
If i cancel the instalation, it is recognized by my pc (active sync comunicates fine) but when i want to flash it to correct the possible problems it lost comunication. Goes to bootloader screen but no comunication.
HELP PLEASE !!!!!!
Help me, task 2a to mtty.exe result is:
Cmd>task 2a
Format ALL start
backup SPL OK
backup MISC configuration OK
SPL start start block=288, total block of CE=1760
Write 0xFF start page=0x4800, total page=0x1B800
SPL version and MFG TAG are same, skip it.
restore SPL OK
restore MISC configuratoin OK
restore MFG configuratoin OK
Format ALL end
again im writen:
Cmd>boot
InitDisplay: Display_Chip=1
Fill RSVD information for block 288 to 309
TAG NOT FOUND !!! NOT CLEAR STORAGE !!!
Card inserted
Cmd5 CMD_TIMEOUT
SD 2.0 LC card
SD Init OK
SDFATChkConf: RhOpenFile() failed KAISCONF.txt
OSSIPreLoad ++
OSSIPreLoad failed, CE is NONE
OEMIPLInit clear 10MB ext RAM
OEMGetUpdateMode
IPLMSG:0x2:ERROR: Failed to open storage partition.
it's possible revert this process?
Hmm, not sure why you wanted to do that since your WM partitions are formatted now. See here
Flash a new ROM if you have one matching your CID or flash any ROM if u have HardSPL.
pda is stopped, screen black, green led is on not avanced.
no input signal.
Not possible flash another ROM, pda no connecting (connecting DATA SERVICES, no drivers)
Emblema said:
pda is stopped, screen black, green led is on not avanced.
no input signal.
Not possible flash another ROM, pda no connecting (connecting DATA SERVICES, no drivers)
Click to expand...
Click to collapse
Remove battery, put it in again, press power and camera button simulaneously. Device should enter bootloader mode (tri colour).
Now you can flash a ROM.
jockyw2001 said:
Remove battery, put it in again, press power and camera button simulaneously. Device should enter bootloader mode (tri colour).
Now you can flash a ROM.
Click to expand...
Click to collapse
not respond, battery is removed 60 min., black screen e green led forever
Emblema said:
not respond, battery is removed 60 min., black screen e green led forever
Click to expand...
Click to collapse
Did you disconnect USB cable? Device must be disconnected else you can not enter bootloader mode.
jockyw2001 said:
Did you disconnect USB cable? Device must be disconnected else you can not enter bootloader mode.
Click to expand...
Click to collapse
Yes im disconnected usb cable, press simultaneily power+camera+stylus effect is screen black e green led.
It looks like you've got a brick since you can not enter SPL Bootloader mode anymore
I'm afraid you will have to send it in for service: http://service.htceurope.com/Wizard.aspx
:-(
tank for help.
im send to warranty
task 2a erases the FLash instead of Bad Blocks so now yr Kaiser do not have the OS.Put it in bootloader and flash the ROM and yr device will b alive.Search for my thread somewhere in Kaiser section for task 2a.
therefore I can send it in attendance or succeed to see what I have made?
Succeed to arrange it I alone?
Tanks
Emblema said:
Succeed to arrange it I alone?
Click to expand...
Click to collapse
As I mentioned before, you can only fix it when you can enter the bootloader. Either by pressing and hold camera button and then power on button, or press both camera and power button at the same time and then press soft reset with stylus. Even if you don't get a tri-color screen, check if you can still connect with MTTY. If not send it to service.
Ok tanks,
object not enter to bootloader mode.
im send to assistance.
Tank all for help me!!
Have I screwed myself here? I went into bootloader mode, ran mtty.exe and ran 'task 2a'. Now I can't get back to bootloader mode (screen stays black). Any workarounds? I think I'm bricked.
- J
my uni stuk at da screen where it says press 0 or x, my desktop pc tell me that usb device not recognized i try all method nothing cant switch on my phone to reach the boot loader mode so cant run mtty utility
i cant charge my battery also its not showing the orange light which comes when u put the uni to charge so i guess cant charge it
mtty not have usb choise
when i make hardrest the screen give me press 0 or x n whatever i press it jus goes blank after that dont go the boot loader mode
i have used the mtty utility earlier 1-2 times but this time i am not able to reach the boot screen so i cant use it
i tried the UNI_ExitBootloader.exe but that also not working
c
i try 2 rest an hard reset 1000000 time
i tried everything nothing working ???????????????????????????????????????????????
pllllllllllllllllllllllllz help 2 make my uni a live
Reply With Quote
mandy_bikerboy said:
my uni stuk at da screen where it says press 0 or x, my desktop pc tell me that usb device not recognized i try all method nothing cant switch on my phone to reach the boot loader mode so cant run mtty utility
i cant charge my battery also its not showing the orange light which comes when u put the uni to charge so i guess cant charge it
mtty not have usb choise
when i make hardrest the screen give me press 0 or x n whatever i press it jus goes blank after that dont go the boot loader mode
i have used the mtty utility earlier 1-2 times but this time i am not able to reach the boot screen so i cant use it
i tried the UNI_ExitBootloader.exe but that also not working
c
i try 2 rest an hard reset 1000000 time
i tried everything nothing working ???????????????????????????????????????????????
pllllllllllllllllllllllllz help 2 make my uni a live
Reply With Quote
Click to expand...
Click to collapse
Try to remove the SDCard and reset the device. if almost persist try the solution proposed in wiki thats says how to exit from bootloader mode.
one thing i just noticed i cant hard reset my phone, when i press the soft keys and reset button nothing happens when i soft reset it nothing happens then also but if i press and hold both the soft keys it lights up and show press o to restore default and x to continue.
whatever i click nothing happens screen goes all black again after that no boot loader mode where u get the serial on the top of the screen and version on bottom cant c anything at all can anyone help in me in making my uni work again or have i wrecked it
i tried mtty but it is not showing me usb coloumn tried exit bootloader but it also does not work it says cannot open usb port make sure usb connection disabled in active syn and make sure usb canle is connected properly
when i attach my uni the pc shows usb device not recognized
PLEASEEEEEEEE HELPPPPPPPPPPPPPPPPPP
Hi
When you want to flash a new ROM you have to remove your SD card. I had the same problem.
Remove it, go to bootscreen mode. Re-flash the ROM.
***Do not worry. These problems arise now and then***
i had done that without sd card and sim card still nothing happened
mandy_bikerboy said:
i had done that without sd card and sim card still nothing happened
Click to expand...
Click to collapse
Hi
I can not tell this is the problem, but what you are telling is somehow a usb break problem.
Try to get your exec to a repair center to have a look at it...
i was following this guide:
http://forum.xda-developers.com/showthread.php?t=448008
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer
3. Goto the Roms Folder and rename the .nbh file to RAPHIMG.nbh
4. Copy the RAPHIMG.nbh file to the root of your microSD Card
5. Remove Sim Card and Restart phone
6. Plug the microSD Card into the phone
7. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears
8. Follow the onscreen instructions to start flashing
9. Once phone finishes flashing and says Update Complete, reset with the stylus
10. When it gets to the screen where it configures the stylus, HARD RESET
(hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)
11. Follow onscreen instructions to set up your New Rom
fine upto step 8, it goes to the tricolour but then it just stops and it says
RAPHL100
SPL-1.90.0000
MICRO-RAPH (LED) V13
MICROP-RAPH (KEY) V5
PSOC-RAPH STAGE_CVT V0X36
and it just crashes....anyone help me?
FORGOT TO ADD:
It goes to a grey screen and says ' no image file'
This is the guide you should have used.
Sounds like you tried to flash your phone before you Hard SPL'd it.
Good luck!
IMO, USB isn't the best way to flash, because of
- not installed USB drivers for device in bootloader mode
- accidental desktop sleep or usb unplug
SD flash though
- corrupt SD card
- those microSD cards accidentally get dislodged and thus bad flash
i think that the best way is to flash via USB and make sure all drivers are installed... don't touch the computer or phone when it's flashing (maybe move the mouse a bit to prevent screensaver etc.)
I have downloaded kaiser-HardSPLv1, i ran it on the pc.
and i got to step 2, it said
http://img297.imageshack.us/i/htc.png/
my phone turns of, then turns back on again and i dont see the tri colour help please!
iraqi4life said:
I have downloaded kaiser-HardSPLv1, i ran it on the pc.
and i got to step 2, it said
http://img297.imageshack.us/i/htc.png/
my phone turns of, then turns back on again and i dont see the tri colour help please!
Click to expand...
Click to collapse
Your phone is NOT a Kaiser, its a raphael.
You really should have read the guide I pointed you to.
It had the link to the correct SPL for your device.
A little time to read would save you hundreds of $
You may find a fix ( there is a hit and miss solution for this) but you really need to search, read and learn.
Start with this thread.
ah okay thanks alot man, i appreciate you're help.
ive done all that, i get the error {262} it stops at 0% for a few mins then displays the 262 error, i have turned of firewall and ive searched the forum, but no avail?
Okay, i tried to do the hard spl with the sim card and memory card out
but still no avail, ive turned off the firewall and then i ran
RaphaelHardSPL-Unsigned_190_1_3 but still can 262 error, please help this is very frustrating!
what happens is that i run through the steps on the RRU, then the phone goes to a black screen, and the progress bar appears, stays at 0% for 2-3 mins then error 262 appears
please help!!
Okay, i have now successfuly hard SPL my phone.
however, i have inserted a ROM in my micro SD hard, pressed volume down and then clicked reset, however i can only see the tri-colour screen and it still says no image .
please help!
OMG
i think i have bricked my phone,
i turn it on and it goes to the TOUCH PRO screen, then nothing happens
ive done it! it worked on the other pc!!! yay
i am using the energy rom standard.
and also, which one has the theme which has it like this:
http://lh3.ggpht.com/_obTK4UolmtY/Sjo8vSiryNI/AAAAAAAAAPg/XBDAHTFuBJw/NRG_3.0_Today.jpg
does it work with the raphael ?
Once again I turn to fellow WinMo community for help.
This started when I was flashing new Energy ROM. After done flashing, the comp said it was done. But the phone was stuck on the tricolor screen. On the background, gone in a flash was 'page missing'.
Sorry that was all I can make out in that flash second.
But weirdly the phone wouldn't startup. I tried to do a hardreset and it took me to 'TRIGGER RAMDUMP MODE' instead of the hardreset screen.
Any ROM I flash completes on desktop but phone stays in tricolor screen.
Now....I can disconnect the USB cable and do a softreset and it starts. But then when I get a call, I can take the call but can never come out of it. It stays blank after the call and wont respond. I have to soft reset again.....
Please help me fix this.
Thanks in advance