My qtek after a reset always go to the bootloader screen (USB v1.0).
I have to take off the battery and wait for a few seconds to power it up again, but it always start as i've done a hard reset.
When it starts again, i have to align the screen, and when it is installing the ext rom, it goes to the bootloader screen AGAIN!!!
If i cancel the instalation, it is recognized by my pc (active sync comunicates fine) but when i want to flash it to correct the possible problems it lost comunication. Goes to bootloader screen but no comunication.
HELP PLEASE !!!!!!
Related
I attempted to upgrade my Orange SPV M500 (HTC Magician).
The tool failed, and did not install anything.
However, my phone has remained stuck on the "Bootloader", displaying a white screen with "serial" if it's not plugged into the Pc, or "USB" when it is.
I've tried different reset techniques, having the battery out for long periods.
My phone booted up once, then silly me I tried the same tool again, and am back stuck!!
I bet it's something simple to press to get it to boot normal - but I just can't see it.
Please help. I know I'm in the right place to ask.
Paul.
Bootloader
you can try camera + record + reset button to get it out off boot loader mode
if it doesn't work you have to flash it
If this doesn't work, just download the correct rom, and run the update program, this will hopefully sort the problem out if pressing the buttons doesn't work.
hope this helps
Mark
How to hard reset
Clear Storage does not help because it not start Windows at all
(i ve save some stupid file in Start UP menu)
i cant figure how to hard reset after pressing two buttons and on/off
becase 3-color screen appears
and nothing happened
hELP
and can i again flash it with same ROM (andot PPE) or i must use another
and what is the procedure.
do i have to use SDA unlocker, TeraTermPro, etc etc
on 3-color screen after i done GSMUPDATE
there is message
on ROmUpdate after verifying
it is error
Cant connect to your Smartphone
HEEEEEELP
Just turn off your phone, press both the soft keys and turn it on back
Hello,
I am fairly new to loading roms, but I have done it already several times successfully both on keiser and wizard,
now Yesterday I wanted to try Dutty's V1 rom and I did, now when it completed it started to boot, with the htc splash screen customized with Dutty's name etc, then it asked me to calibrate the pen, you know the normal stuff.....then it stopped booting it will get stuck into a white screen,
and it stays there, it will not active sync, it starts fine, I read: R 1.65.16.24
g 25.83.40.02W D 3.5Dutty's . then it gets into this white screen and stays till the backlite goes off, if I tap the screen the backlite goes back on, and one time I was able to hold the off button and I got even a message saying " if you disconnect them you might lose some data, continue yes or no". Tapping no or yes made no difference.
Please Help, I need to enter bootloader in some way, please help !
can you enter bootloader mode?
keep the camera button pressed and soft reset with ur stylus....or turn off ur phone and keep the camera button pressed and press the power button of ur device...
if you can enter bootloader mode...just reflash dutty's rom or maybe flash some other rom and you should be fine
Once it started to calibrate the stylus is when you Hard reset.
Please Help, I need to enter bootloader in some way, please help !
Click to expand...
Click to collapse
You definately need more lecture.
i was following this guide:
http://forum.xda-developers.com/showthread.php?t=448008
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer
3. Goto the Roms Folder and rename the .nbh file to RAPHIMG.nbh
4. Copy the RAPHIMG.nbh file to the root of your microSD Card
5. Remove Sim Card and Restart phone
6. Plug the microSD Card into the phone
7. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears
8. Follow the onscreen instructions to start flashing
9. Once phone finishes flashing and says Update Complete, reset with the stylus
10. When it gets to the screen where it configures the stylus, HARD RESET
(hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)
11. Follow onscreen instructions to set up your New Rom
fine upto step 8, it goes to the tricolour but then it just stops and it says
RAPHL100
SPL-1.90.0000
MICRO-RAPH (LED) V13
MICROP-RAPH (KEY) V5
PSOC-RAPH STAGE_CVT V0X36
and it just crashes....anyone help me?
FORGOT TO ADD:
It goes to a grey screen and says ' no image file'
This is the guide you should have used.
Sounds like you tried to flash your phone before you Hard SPL'd it.
Good luck!
IMO, USB isn't the best way to flash, because of
- not installed USB drivers for device in bootloader mode
- accidental desktop sleep or usb unplug
SD flash though
- corrupt SD card
- those microSD cards accidentally get dislodged and thus bad flash
i think that the best way is to flash via USB and make sure all drivers are installed... don't touch the computer or phone when it's flashing (maybe move the mouse a bit to prevent screensaver etc.)
I have downloaded kaiser-HardSPLv1, i ran it on the pc.
and i got to step 2, it said
http://img297.imageshack.us/i/htc.png/
my phone turns of, then turns back on again and i dont see the tri colour help please!
iraqi4life said:
I have downloaded kaiser-HardSPLv1, i ran it on the pc.
and i got to step 2, it said
http://img297.imageshack.us/i/htc.png/
my phone turns of, then turns back on again and i dont see the tri colour help please!
Click to expand...
Click to collapse
Your phone is NOT a Kaiser, its a raphael.
You really should have read the guide I pointed you to.
It had the link to the correct SPL for your device.
A little time to read would save you hundreds of $
You may find a fix ( there is a hit and miss solution for this) but you really need to search, read and learn.
Start with this thread.
ah okay thanks alot man, i appreciate you're help.
ive done all that, i get the error {262} it stops at 0% for a few mins then displays the 262 error, i have turned of firewall and ive searched the forum, but no avail?
Okay, i tried to do the hard spl with the sim card and memory card out
but still no avail, ive turned off the firewall and then i ran
RaphaelHardSPL-Unsigned_190_1_3 but still can 262 error, please help this is very frustrating!
what happens is that i run through the steps on the RRU, then the phone goes to a black screen, and the progress bar appears, stays at 0% for 2-3 mins then error 262 appears
please help!!
Okay, i have now successfuly hard SPL my phone.
however, i have inserted a ROM in my micro SD hard, pressed volume down and then clicked reset, however i can only see the tri-colour screen and it still says no image .
please help!
OMG
i think i have bricked my phone,
i turn it on and it goes to the TOUCH PRO screen, then nothing happens
ive done it! it worked on the other pc!!! yay
i am using the energy rom standard.
and also, which one has the theme which has it like this:
http://lh3.ggpht.com/_obTK4UolmtY/Sjo8vSiryNI/AAAAAAAAAPg/XBDAHTFuBJw/NRG_3.0_Today.jpg
does it work with the raphael ?
Once again I turn to fellow WinMo community for help.
This started when I was flashing new Energy ROM. After done flashing, the comp said it was done. But the phone was stuck on the tricolor screen. On the background, gone in a flash was 'page missing'.
Sorry that was all I can make out in that flash second.
But weirdly the phone wouldn't startup. I tried to do a hardreset and it took me to 'TRIGGER RAMDUMP MODE' instead of the hardreset screen.
Any ROM I flash completes on desktop but phone stays in tricolor screen.
Now....I can disconnect the USB cable and do a softreset and it starts. But then when I get a call, I can take the call but can never come out of it. It stays blank after the call and wont respond. I have to soft reset again.....
Please help me fix this.
Thanks in advance