My qtek after a reset always go to the bootloader screen (USB v1.0).
I have to take off the battery and wait for a few seconds to power it up again, but it always start as i've done a hard reset.
When it starts again, i have to align the screen, and when it is installing the ext rom, it goes to the bootloader screen AGAIN!!!
If i cancel the instalation, it is recognized by my pc (active sync comunicates fine) but when i want to flash it to correct the possible problems it lost comunication. Goes to bootloader screen but no comunication.
HELP PLEASE !!!!!!
AFTER UNLOCK NO VOICE OR SPEAKER WORKING I JUST FLASHED WITH
(RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27.04.15_Test) NOW PHONE DOESNT
POWER UP OR BOOT MODE BLANK SCREEN
I TRY TO CONNECT TO THE COMPUTER ASKING DRIVER (DATE INTERFACE)
I NEED YOUR HELP TO GET BACK LIVE
PLEASE
THANKS
How did you unlock it? Did you CID unlock? HardSPL version? Can you get to the bootloader by holding down the camera button and power button and soft reset at the same time?
From the sound of things you loaded a CID locked rom onto your locked phone. This is only a guess though based on the fact that the ROM you loaded included a compatible radio.
Just a tip, next time don't use all caps. It's considered shouting and inappropriate. We understand your urge to get it fixed so we'll help even without the caps
Answering Alibaba0101's questions will help a lot. Also, have you tried taking the battery out and putting it back in?
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
lxa786 said:
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
Click to expand...
Click to collapse
I don't see the step where you flashed your original radio back after doing the SIM unlock. The radio that you is a special "patched" radio, and the phone will not successfully boot into Windows with it flashed.
Go into the bootloader (hold Camera during power on), and flash a compatible radio. If you haven't flashed a cooked ROM yet, then just hit up the Kaiser Wiki and grab the original ship radio for your phone.
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
austinsnyc said:
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
Click to expand...
Click to collapse
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Boot Loader
Same here I just hold down camera button and soft reset works every time.
hi I need your more help how can I get phone on boot mode phone dead not responding I tried more then 10 time by pressing camera and power button phone still blank screen.
No display show so how can I flash the phone
Any idea to flash the phone dead mode?
thanks
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
This has gotten people in the past, so sorry if it sounds dumb.
The Camera button has two settings Full Press and Half Press. Press until it stops then press again. You need to be pushing the Camera Button down all the way to get into Bootloader.
Also I never need to press the power Power Button As well.
I may be wrong but, when the phone is on, you can press the Camera and Soft Reset buttons. When the phone is off, you press the Power, Camera, and Soft Reset buttons to go directly into boot loader.
i tried but screen still blank no light nothing when i put usb into the phone asking driver (data interface)?
Can not go in bootloader help?
Tytn 2 is dead .
Ok last night I try to install the new hyperdragon III BlackStone rom everything is fine untill it finish and it cant load in to window, the computer keep asking me for the data interface and the tilt keep restart and the screen only shows hyperdragen III. I was running hyperdragon III opal (10/11/08) I tried MMTY and reinstall the OE rom but no luck, please help!!
Tytn2 Dead or not??
Tytn 2 is dead if you see data interface driver when put in usb cabel install v3 motorola driver and you will see data qualcomm usb driver i device manager .... this mean that totaly erased memory in tytn2 and its dead,only with jtag can flash again.
Please, tell me how can y do it. I have the same problem....
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Click to expand...
Click to collapse
I don't see any step about using the white screen fix so I'm guessing you didn't successfully install HardSPL and then after that you tried flashing a ROM whilst being oblivious to the fact that Hard SPL wasn't installed, so you most likely bricked your phone
AllTheWay said:
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Click to expand...
Click to collapse
Dead HTC KAISER
Hello My friends
After along search and Googling on the net without finding any solution. at last I did took a Risk to solve and save my DEAD HTC KAISER . what i did is I ressembled the HTC KAISER , to see if my USB data input was defect, but it was Good, now .......he he.. what i fond avery smal Batterie planted on the motherboard , i took it of the the board , end waited 1 hour . then i place it back , assembeled my HTC KAISER back
Taaaaraaaaa my HTC KAISER Power Led went ON ,,, YES ..Friends . is charging .
after 1/2 hour , I swish the HTC on ,,,, heeeee Is working......flash it with the new ROM wm 6.5 ...really it went Perfect.. end My HTC KAISER... ALIVE AGAIN.
Greatins , and hoppe this will Help you..........Good Luck .
on youtube you can find videos how to dissembele your HATC KAISER.
thanks to XDA-Developers , for this great Forum.
ericc191 said:
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
Click to expand...
Click to collapse
my kaiser boots up but after the att thing the screen gos black do you know how to fix this
Good Day!
i made a very stupid mistake. i tried to update my Magician with Wizzard ROM.
The process went good, all the steps had been done perfectly, but my MDA crashed totally. The only think, that's happening when i'm pressing on/off button is a once instant flash of display.
I know, that's is too naive from my side to think that there is any hope, but anyway: is there any way how to solve this problem?
pls help me
i was trying to upgrade my magician rom but it stopped in midway. it is showing a dark display and mention Serial on to and v1.00 at bottom.
pls help me how to give life to my pda. have tried to soft and hard reset but didnt work. thanks
do u able to start bootloader (POWER +CAMERA hold and press reset)
Cotulla said:
do u able to start bootloader (POWER +CAMERA hold and press reset)
Click to expand...
Click to collapse
I am having the same problems as bplb71....
No way to do a HardReset or Leave bootloader.... It got stuck
Now what??
Cotulla said:
do u able to start bootloader (POWER +CAMERA hold and press reset)
Click to expand...
Click to collapse
found a mgician and it starts but hangs o the align screen
the thing you need to press keeps moving arround the screen for 20 min and then i stopped
i am also having the same problem.,, cant enter the bootloader or hard reset ,,,,,magician is stuck now,,, what should i do now???? i am worried.
happend to me to
i have same problem but when i let battery run out and then plug into wall it boots normally but then it asks to restarts after setup and back to square one help plz
Hi,
Newbie here....A pola200 came to me for password...incoming and outgoing call working..how ever there is a password..wats the best way to remove the password...Or how do i go abt hard resetting it
Thanks in advance
cliffrock
Well as i see there is no one answering me the question....
I found my own solution:
Hard Reset:
On the 02 Orbit2, make sure the phone is powered on and then press AND HOLD the Windows and OK buttons down at the same time, THEN use your stylus to press AND RELEASE the reset button (while you CONTINUE to hold down the Windows and OK buttons). You should get a grey-ish/white screen explaining how to complete the hard reset or how to cancel the operation.
If you cannot see anything on your screen due to the OS being totally messed up (in other words, as long as it's not hardware failure), then you need to put your device into bootloader mode (4-color screen) so that you can flash the ROM (either what you already are using, or a newly cooked one - either way you need to have a ROM image file on your computer to complete the flashing process).
Bootloader Mode:
To enter bootloader mode, press AND HOLD the camera button and then press AND RELEASE the soft reset with your stylus. When the screen is showing the 4 color bands, plug in the USB cable between your computer and phone flash the ROM.
Click to expand...
Click to collapse
Br
cliffrock
Thanks man, working good.
Very thanks
Hello
I had HTC Diamond before and now i bought HTC Touch Pro.
It has original O2 rom and I am trying to flash a new one. But I cannot enter bootloader. I did Hard-SPL but since i cannot enter bootloader I cannot check if it was succesful or not. I tried all the button combinations (like vol down + enter + reset etc...) but it was unsuccesfull. And i even tried to copy EnterBootloader.exe to the phone and run it. But the screen just goes black and thats all. And when I was trying to do HARD-SPL the screen also went only black. I never seen the three color screen. Please help me!
Thanks
Moved as not ROM Development.
Well, you're probably doing it wrong. Hold volume down, then soft reset. Keep holding vol down until the tricolor screen appears. Don't hold the reset button down; just push it and release it.
Im doing it right. Im sure
so u re trying to flash via card or not, if you're trying to flash via PC dont forget to connect with active sync before, if you are trying to connect with SD card dont forget to do a clean format of it before
I remembered that I actually had the issue once (no idea why, it only happened on one rom about a year ago). Try doing a hard reset, then go into bootloader (instead of pushing vol up and re-booting). If that doesn't work, then start the boot process, and when it hits the alignment screen, try to go into bootloader.