Database Info

Does it mean its bricked?

So i just flashed my vox with dr.gonzo's new 1.0 rom...and I did it the same way i've been doing it for months now (since his first rom 0.1) and it all went good, but when it was suppose to reboot turned off but never turned back on....I turn it on manually and i see the htc logo, it vibrates and then black screen... nothing happens afterwards...please dont tell me its bricked...please.....

If you're not able to get it into the bootloader to run an RUU then I suggest that you flash a signed HTC ROM, flash USPL and then re-flash New Guava v1.0

how do i flash a signed htc rom? when i turn it on, the htc logo comes on, then vibrates, and then a black screen.... when i try a hard reset, it asks me to confirm by pressing send. i press send (correct me if i'm wrong, send is the green 'phone' button right?) and it loads up the htc logo, vibrates and then shuts off. I've never had a bricked phone before, this all just doens't make sense i did the same steps that i've always done.

Seriously? Your phone is not bricked.
If you've flash a ROM before, it's the exact same procedure - what you can try and do is load into the bootloader by holding the camera button and plugging in a USB cable, it will start into the tri-color screen and should show USB is connected then you can flash a signed HTC ROM.
If the ROM is corrupt, this is your best way of "recovering" your phone, if the ROM was flashed properly, after getting into the bootloader, run ruurun 0 and ResetDevice to boot it back into OS.

oh ok, i haven't tried that yet (bootloader mode that is). Now you say i do this by plugging the usb and holding the power button and camera button? is that how it works? h4waii, you just lightened up my day by giving me some hope!

That is how you can enter the boot loader.
1). Turn off and unplug the Vox from external power/USB cable
2). Press and hold the camera button
3). Insert external power/USB cable
4). Continue to hold camera button until you enter the tri-color screen
At this point, you should have a "USB" text label on the bottom left hand side indicating USB is detected - you can then run an RUU from a signed HTC ROM to update it.

press and hold the camera button alone? i tried that, it doesn't power up the unit though?

Yes it does. Hold camera and plug in your USB cable (making sure it's also plugged into your computer).

ok i got it to the triband screen, but when i ran dr.gonzo's rom it got to 3% and said its corrupt. so i'm gonna do what you said and flash a signed htc rom. hopefully it works....

Yes, 3% because SPL is not patched to allow an unsigned ROM to be loaded, flash an HTC ROM to it, once that is complete you can run USPL to re-flash New Guava.
It will work, don't need to hope

you are a godsend! literally have no idea how depressed i was yesterday! being a university student money is very tight right now so was a total shock when i realized i bricked my $350 phone....I wish i had money cause i'd send you some for being so helpful but I dont... So just please understand i REALLLY appreciate your help, thank you.

That's what we're here for. Glad to be of service.

Htc Kaiser Dead After Flash Finshed

AFTER UNLOCK NO VOICE OR SPEAKER WORKING I JUST FLASHED WITH
(RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27.04.15_Test) NOW PHONE DOESNT
POWER UP OR BOOT MODE BLANK SCREEN
I TRY TO CONNECT TO THE COMPUTER ASKING DRIVER (DATE INTERFACE)
I NEED YOUR HELP TO GET BACK LIVE
PLEASE
THANKS

How did you unlock it? Did you CID unlock? HardSPL version? Can you get to the bootloader by holding down the camera button and power button and soft reset at the same time?
From the sound of things you loaded a CID locked rom onto your locked phone. This is only a guess though based on the fact that the ROM you loaded included a compatible radio.

Just a tip, next time don't use all caps. It's considered shouting and inappropriate. We understand your urge to get it fixed so we'll help even without the caps
Answering Alibaba0101's questions will help a lot. Also, have you tried taking the battery out and putting it back in?

The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS

lxa786 said:
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
Click to expand...
Click to collapse
I don't see the step where you flashed your original radio back after doing the SIM unlock. The radio that you is a special "patched" radio, and the phone will not successfully boot into Windows with it flashed.
Go into the bootloader (hold Camera during power on), and flash a compatible radio. If you haven't flashed a cooked ROM yet, then just hit up the Kaiser Wiki and grab the original ship radio for your phone.

Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly

austinsnyc said:
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
Click to expand...
Click to collapse
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.

Boot Loader
Same here I just hold down camera button and soft reset works every time.

hi I need your more help how can I get phone on boot mode phone dead not responding I tried more then 10 time by pressing camera and power button phone still blank screen.
No display show so how can I flash the phone
Any idea to flash the phone dead mode?
thanks

If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.

This has gotten people in the past, so sorry if it sounds dumb.
The Camera button has two settings Full Press and Half Press. Press until it stops then press again. You need to be pushing the Camera Button down all the way to get into Bootloader.
Also I never need to press the power Power Button As well.

I may be wrong but, when the phone is on, you can press the Camera and Soft Reset buttons. When the phone is off, you press the Power, Camera, and Soft Reset buttons to go directly into boot loader.

i tried but screen still blank no light nothing when i put usb into the phone asking driver (data interface)?

Can not go in bootloader help?
Tytn 2 is dead .

Ok last night I try to install the new hyperdragon III BlackStone rom everything is fine untill it finish and it cant load in to window, the computer keep asking me for the data interface and the tilt keep restart and the screen only shows hyperdragen III. I was running hyperdragon III opal (10/11/08) I tried MMTY and reinstall the OE rom but no luck, please help!!

Tytn2 Dead or not??
Tytn 2 is dead if you see data interface driver when put in usb cabel install v3 motorola driver and you will see data qualcomm usb driver i device manager .... this mean that totaly erased memory in tytn2 and its dead,only with jtag can flash again.

Please, tell me how can y do it. I have the same problem....

Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Click to expand...
Click to collapse
I don't see any step about using the white screen fix so I'm guessing you didn't successfully install HardSPL and then after that you tried flashing a ROM whilst being oblivious to the fact that Hard SPL wasn't installed, so you most likely bricked your phone

AllTheWay said:
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Click to expand...
Click to collapse
Dead HTC KAISER
Hello My friends
After along search and Googling on the net without finding any solution. at last I did took a Risk to solve and save my DEAD HTC KAISER . what i did is I ressembled the HTC KAISER , to see if my USB data input was defect, but it was Good, now .......he he.. what i fond avery smal Batterie planted on the motherboard , i took it of the the board , end waited 1 hour . then i place it back , assembeled my HTC KAISER back
Taaaaraaaaa my HTC KAISER Power Led went ON ,,, YES ..Friends . is charging .
after 1/2 hour , I swish the HTC on ,,,, heeeee Is working......flash it with the new ROM wm 6.5 ...really it went Perfect.. end My HTC KAISER... ALIVE AGAIN.
Greatins , and hoppe this will Help you..........Good Luck .
on youtube you can find videos how to dissembele your HATC KAISER.
thanks to XDA-Developers , for this great Forum.

ericc191 said:
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
Click to expand...
Click to collapse
my kaiser boots up but after the att thing the screen gos black do you know how to fix this

Help Cant Reach Boot Loader Mode

my uni stuk at da screen where it says press 0 or x, my desktop pc tell me that usb device not recognized i try all method nothing cant switch on my phone to reach the boot loader mode so cant run mtty utility
i cant charge my battery also its not showing the orange light which comes when u put the uni to charge so i guess cant charge it
mtty not have usb choise
when i make hardrest the screen give me press 0 or x n whatever i press it jus goes blank after that dont go the boot loader mode
i have used the mtty utility earlier 1-2 times but this time i am not able to reach the boot screen so i cant use it
i tried the UNI_ExitBootloader.exe but that also not working
c
i try 2 rest an hard reset 1000000 time
i tried everything nothing working ???????????????????????????????????????????????
pllllllllllllllllllllllllz help 2 make my uni a live
Reply With Quote

mandy_bikerboy said:
my uni stuk at da screen where it says press 0 or x, my desktop pc tell me that usb device not recognized i try all method nothing cant switch on my phone to reach the boot loader mode so cant run mtty utility
i cant charge my battery also its not showing the orange light which comes when u put the uni to charge so i guess cant charge it
mtty not have usb choise
when i make hardrest the screen give me press 0 or x n whatever i press it jus goes blank after that dont go the boot loader mode
i have used the mtty utility earlier 1-2 times but this time i am not able to reach the boot screen so i cant use it
i tried the UNI_ExitBootloader.exe but that also not working
c
i try 2 rest an hard reset 1000000 time
i tried everything nothing working ???????????????????????????????????????????????
pllllllllllllllllllllllllz help 2 make my uni a live
Reply With Quote
Click to expand...
Click to collapse
Try to remove the SDCard and reset the device. if almost persist try the solution proposed in wiki thats says how to exit from bootloader mode.

one thing i just noticed i cant hard reset my phone, when i press the soft keys and reset button nothing happens when i soft reset it nothing happens then also but if i press and hold both the soft keys it lights up and show press o to restore default and x to continue.
whatever i click nothing happens screen goes all black again after that no boot loader mode where u get the serial on the top of the screen and version on bottom cant c anything at all can anyone help in me in making my uni work again or have i wrecked it
i tried mtty but it is not showing me usb coloumn tried exit bootloader but it also does not work it says cannot open usb port make sure usb connection disabled in active syn and make sure usb canle is connected properly
when i attach my uni the pc shows usb device not recognized
PLEASEEEEEEEE HELPPPPPPPPPPPPPPPPPP

Hi
When you want to flash a new ROM you have to remove your SD card. I had the same problem.
Remove it, go to bootscreen mode. Re-flash the ROM.
***Do not worry. These problems arise now and then***

i had done that without sd card and sim card still nothing happened

mandy_bikerboy said:
i had done that without sd card and sim card still nothing happened
Click to expand...
Click to collapse
Hi
I can not tell this is the problem, but what you are telling is somehow a usb break problem.
Try to get your exec to a repair center to have a look at it...

Help, trying to flash.

i was following this guide:
http://forum.xda-developers.com/showthread.php?t=448008
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer
3. Goto the Roms Folder and rename the .nbh file to RAPHIMG.nbh
4. Copy the RAPHIMG.nbh file to the root of your microSD Card
5. Remove Sim Card and Restart phone
6. Plug the microSD Card into the phone
7. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears
8. Follow the onscreen instructions to start flashing
9. Once phone finishes flashing and says Update Complete, reset with the stylus
10. When it gets to the screen where it configures the stylus, HARD RESET
(hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)
11. Follow onscreen instructions to set up your New Rom
fine upto step 8, it goes to the tricolour but then it just stops and it says
RAPHL100
SPL-1.90.0000
MICRO-RAPH (LED) V13
MICROP-RAPH (KEY) V5
PSOC-RAPH STAGE_CVT V0X36
and it just crashes....anyone help me?
FORGOT TO ADD:
It goes to a grey screen and says ' no image file'

This is the guide you should have used.
Sounds like you tried to flash your phone before you Hard SPL'd it.
Good luck!

IMO, USB isn't the best way to flash, because of
- not installed USB drivers for device in bootloader mode
- accidental desktop sleep or usb unplug
SD flash though
- corrupt SD card
- those microSD cards accidentally get dislodged and thus bad flash
i think that the best way is to flash via USB and make sure all drivers are installed... don't touch the computer or phone when it's flashing (maybe move the mouse a bit to prevent screensaver etc.)

I have downloaded kaiser-HardSPLv1, i ran it on the pc.
and i got to step 2, it said
http://img297.imageshack.us/i/htc.png/
my phone turns of, then turns back on again and i dont see the tri colour help please!

iraqi4life said:
I have downloaded kaiser-HardSPLv1, i ran it on the pc.
and i got to step 2, it said
http://img297.imageshack.us/i/htc.png/
my phone turns of, then turns back on again and i dont see the tri colour help please!
Click to expand...
Click to collapse
Your phone is NOT a Kaiser, its a raphael.
You really should have read the guide I pointed you to.
It had the link to the correct SPL for your device.
A little time to read would save you hundreds of $
You may find a fix ( there is a hit and miss solution for this) but you really need to search, read and learn.
Start with this thread.

ah okay thanks alot man, i appreciate you're help.
ive done all that, i get the error {262} it stops at 0% for a few mins then displays the 262 error, i have turned of firewall and ive searched the forum, but no avail?

Okay, i tried to do the hard spl with the sim card and memory card out
but still no avail, ive turned off the firewall and then i ran
RaphaelHardSPL-Unsigned_190_1_3 but still can 262 error, please help this is very frustrating!
what happens is that i run through the steps on the RRU, then the phone goes to a black screen, and the progress bar appears, stays at 0% for 2-3 mins then error 262 appears
please help!!

Okay, i have now successfuly hard SPL my phone.
however, i have inserted a ROM in my micro SD hard, pressed volume down and then clicked reset, however i can only see the tri-colour screen and it still says no image .
please help!

OMG
i think i have bricked my phone,
i turn it on and it goes to the TOUCH PRO screen, then nothing happens

ive done it! it worked on the other pc!!! yay
i am using the energy rom standard.
and also, which one has the theme which has it like this:
http://lh3.ggpht.com/_obTK4UolmtY/Sjo8vSiryNI/AAAAAAAAAPg/XBDAHTFuBJw/NRG_3.0_Today.jpg
does it work with the raphael ?

HTC Touch Pro T7272 Stuck at Startup

Hello, well, after several searching ended up here... my first post (like all of us when in trouble)
When trying to enter the tri-color screen, we pressed several times power+volume down and reset button but the phone never gets there, no matter what you do and now it is stuck at the "boot" screen that says: "Touch pro" in white letters and in the right down corner, with red letters says:
R 1.02.25.19
G 52.33.25.17W
D 1.94.00.00
Now, what to do here? it doesn´t boot, no hard reset, no nothing, if i press the reset button re-powers and gets there again... help..!!!
Thanks.
Sergio.

squiros1976 said:
Hello, well, after several searching ended up here... my first post (like all of us when in trouble)
When trying to enter the tri-color screen, we pressed several times power+volume down and reset button but the phone never gets there, no matter what you do and now it is stuck at the "boot" screen that says: "Touch pro" in white letters and in the right down corner, with red letters says:
R 1.02.25.19
G 52.33.25.17W
D 1.94.00.00
Now, what to do here? it doesn´t boot, no hard reset, no nothing, if i press the reset button re-powers and gets there again... help..!!!
Thanks.
Sergio.
Click to expand...
Click to collapse
Do entering bootloader : http://wiki.xda-developers.com/index.php?pagename=Raphael_For_Beginners#bootloader (With the device turned off, press and hold the VOLUME DOWN and POWER buttons, then press the RESET button with the stylus)
Then flash new ROM, i hope it's helping

Already tried that...
erwinpiero said:
Do entering bootloader :
(With the device turned off, press and hold the VOLUME DOWN and POWER buttons, then press the RESET button with the stylus)
Then flash new ROM, i hope it's helping
Click to expand...
Click to collapse
That´s exactly why i ended with the phone stuck at the first time... i recently got this phone and i wanted to see the bootloader version and stuff to do a firmware update but now it´s just there all the time. Not even being recognized by the pc.
Thanks.

Had You try flash via SD Card?

erwinpiero said:
Had You try flash via SD Card?
Click to expand...
Click to collapse
Well, no, i don´t have an sd card available now... one thing i forgot to say is the phone, after it is on that screen, never turns off again unless you remove the battery... and yes, i have left it on for a day, same thing...
What is the procedure to do the sd card flash thing? it that needs to get to the tree-color screen forget it... that´s exactly what the phone doesn´t do...
Thanks.
Sergio.

Hello Sir, to flash using SD card, you can read it here http://forum.xda-developers.com/showthread.php?t=448008 see number 5.

HTC Fuze
I had the same problem. None of the hard resets worked on my phone. The screen would be stuck on my lock screen and unresponsive. It would not shut off unless the battery was taken out.
Now it's working fine, all I had to do was press the reset button and enter in the code a1b2c3.
Hope this helps.

nessab04 said:
I had the same problem. None of the hard resets worked on my phone. The screen would be stuck on my lock screen and unresponsive. It would not shut off unless the battery was taken out.
Now it's working fine, all I had to do was press the reset button and enter in the code a1b2c3.
Hope this helps.
Click to expand...
Click to collapse
Hi,
Interesting... i´m not the only one with that problem then.... code doesn´t do anything... still same screen....

...no bootloader...
erwinpiero said:
Hello Sir, to flash using SD card, you can read it here --- see number 5.
Click to expand...
Click to collapse
Hello,
Ok, well, the main problem here is that i can´t get into bootloader... the phone is stuck at the fist "Touch pro" screen and nothing else happens...

Anyone with a clue on this? is this phone bricked then...

you sure youre puttin it into bootloader correctly? these things are pretty hard to brick, and can be put through hell and back and still be able to put into bootloader. make sure the hold VOLUME DOWN + POWER, and at the same time RESET WITH THE STYLUS IN THE BOTTOM...youll want to HOLD ALL THREE untill you see the tri colour bootloader screen. keep trying mate, it should go

Finally got bootloader...
the-wrangler said:
you sure youre puttin it into bootloader correctly? these things are pretty hard to brick, and can be put through hell and back and still be able to put into bootloader. make sure the hold VOLUME DOWN + POWER, and at the same time RESET WITH THE STYLUS IN THE BOTTOM...youll want to HOLD ALL THREE untill you see the tri colour bootloader screen. keep trying mate, it should go
Click to expand...
Click to collapse
Finally, after several tries it got into bootloader... now the thing doesn't end here because for some reason when i try to upload the Raphael Hard_SPL the phone goes ok to 0% and in about a minute a communication error appears and that's it...
We are moving forward... at least.

Bootloader Info.
Tried to flash via microSD but the phone says not allow..i guess that's because the hard SPL is not installed and it has the stock... here's what the bootloader shows, i'm not being able to install olinex hardSPL...
RAPH100
SPL-1.94.0000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
PCBID 0x80
RID 0x0
ideas?

...no way to flash it back....
so... i guess there´s no way to get this back into business... when trying to flash always reports communication error at 0%...

You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.

Farmer Ted said:
You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.
Click to expand...
Click to collapse
ya i just noticed the RAPH100 in his info he posted and the t7272 in the header..mines a RAPH800 and bootloader HAS to have vol + power..anyway, i remember having an issue with something similar with my old vogue..have you tried flashing the shipped stock rom back on? if not, try flashing the stock back on it and if it goes, then try the unlock afterwards. dont fret bud, someone here will get you sorted out
here, i found this as im not well versed in raph100s. its a chart with raph100 roms. im sure some must be shipped stock roms and may be worth a try. sorry i couldnt help more, like i said hopefully someone who knows your device better may be able to help
http://wiki.xda-developers.com/index.php?pagename=HTC_Raphael_WM6.1_ROMs

How about flashing official ROM via microSD card?

patrick_spd4u said:
How about flashing official ROM via microSD card?
Click to expand...
Click to collapse
Download the official rom, right click on the exe and extract it somewhere, you'll get several files, rename RUU_signed.nbh to raphimg.nbh, move it to the root of your sd card and you should be able to install it. It should contain splash screen, radio and os.

No way to flash HardSPL...
Hello, thank you for your help! in fact the volume down+reset works perfect to get into bootloader but every time i try to flash hardSPL or stock rom via USB it says "communication error" and the phone displays a 0% bar...
Windows7 is detecting it as HTC USB Sync.
Thanks..
Farmer Ted said:
You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.
Click to expand...
Click to collapse

...will try it again...
Hi
In fact the most close to the rom i had on that cell is ruu_signed_1.90.401.1_wwe, downloaded it and will try it again later using sdcard... one thing i wonder is the SPL version which is 1.94.00.00 on my phone.
Sergio.
freakzone said:
Download the official rom, right click on the exe and extract it somewhere, you'll get several files, rename RUU_signed.nbh to raphimg.nbh, move it to the root of your sd card and you should be able to install it. It should contain splash screen, radio and os.
Click to expand...
Click to collapse