Related
I finally got the nerves to put the new radio and rom version on my HTC Touch pro.
It went wrong at 1%, and the recovery option was in a loop.
So I did exit the process after recovering/restarting like 12 times.
It did exit on a 262 error at 0% or 1%...
Ok let’s try one other rom; now I did first run the HardSPL Unsigned 190.1.3 again as advised before every rom update, and it was successful...
But when booting the phone it is stuck at the black TOUCHpro screen with the following red text at the right bottom.
R 1.02.25.19
G 52.33.25.17U
D 1.90.00.00
Now whatever I try, whatever rom version I use, it always tells me the phone is not connected by USB.
Seems like the USB driver or something is not loaded at this stage. Maybe when by some key combination I get the phone in the ROM/Boot loading menu I can try other rom version. But I could be completely on the wrong track here.
I was so happy with my WM6 phone, please help me so I can enjoy my phone again, hopefully not with the old rom and radio ofc, when possible.
Don't panic!
Put a the NBH file of the rom you want to flash on your storage card and rename it to RAPHIMG.NBH. Start the bootloader (reset and keep pressing the volume down button) and follow the directions on the screen. When it sais it flashed succesful reset again.
Of course this only work if you did install the hardspl...
Good luck,
Cheers,
Cacti
Ok found that when I go in bootloader mode manually by pressing the Volume-down and reset button at the same time it can connect to my PC.
But no matter what rom version I try, original, Stock or custom it stops at 0% or 1% .. Giving me any of these errors :
readme.doc said:
ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
Click to expand...
Click to collapse
Plz help me, I am using the original USB cable and did try a general one, no-USB hub, did remove my firewall/virus scanner software and all.
Put the NBH file on you storage card and rename it. Don't use rhe RUU...
Thanks le_cactus, the above message crossed yours..
I will try getting the new rom trough my MicroSD card, good thing I have no regular Diamond..
Diamond?
This is the HTC Touch Pro forum
Yhea I know, I have the TouchPro... aka as the Professional version of the HTC Diamond in the Netherlands.
Raphael is rarely used here, only by people who are into rom's and TF3D hacks and stuff...
Damn my CF/MD adapter does not seem to work, or my card reader, printer with card reader and my iPaq don't support 8GB cards..
Guess I have to go to the shop tomorrow for a smaller card with a new adapter or a card reader that accepts MicroSD to get my phone back to order.
Thanks for your advice and cooling down my panic moment.. "Bedankt !!!"
Thanks man for 14 euro's I did buy me a card-reader that is able to handle my 8GB microSD card and my problem is solved. Running on 405.3 with latest .28 radio drivers now.
**MY PHONE IS NOW WORKING***
Hey guys,
I am going to start by saying that I have read almost every single sticky, thread, wiki and anything else I could get my grubby hands on to try and solve my problem; but I fear I may have missed something, or done it wrong.
Now to my problem. My friend who had the same phone as me did a HardSPL flash a long time ago and gave me some new ROM. It worked for awhile but wasn't great so we changed to a different ROM. After awhile I got sick of this one and all of its bugs so about 3 days ago we got some with windows 6.5; unfortunately something happened; causing it to be highly unstable, so we switched AGAIN.
Now to my problem. It will not boot. If I just let it boot without doing anything *or if I hit keys* it goes to an hTc TyTn2 screen with the R; G; and D displayed. I tried to flash it via Micro sd card but all I get is a white screen with blue "loading..." and nothing; it will sit there indefinitely. I have been following cmonex's instructions to a "T" and I am stuck. I attempted to do the USB route and the phone will display the tri-colors and say USB, but my computer *Vista* isn't seeing the phone. I tried different USB ports etc. and nothing. Please let me know what you guys think; anything would be greatly appreciated.
~big3
I would recommend down-grading to xp. But if you can't try to explore the drive as a removable driver
Are you sure when you flashed it via MicroSD you had only one file named KAISIMG.nbh on the card?
This happened to me about a month ago, if it's still going to bootloader there is a good chance you can recover but the process is a bit intricate, especially to a newcomer like myself. I spent more time reading on how to fix this issue than I did on the entire process of flashing roms, mtty specifically. These are the threads I used to get running again, don't lose hope. I assure you the your answer is there.
http://forum.xda-developers.com/showthread.php?t=397157&page=4
http://forum.xda-developers.com/showthread.php?t=371154
http://forum.xda-developers.com/showthread.php?t=370169
I am sure. I even reformatted the sd card to a FAT32. It goes to a loading screen then freezes. I can also get it into the tri-color screen and have it say USB at the bottom, but when I try and flash it via USB; for some reason it starts at 0% and then crashes.
I am able to work with it in MTTY and I had to use a Task 8 command for anything to happen. I was told my friend already did a HARDSPL; is it possible that this was deleted/ corrupted?
Put your phone in bootloader mode what does it say?
Have you tried a Hard Reset yet?
Ta
Dave
hey everyone, My phone is temporarily working at this point!!!
My new question is, how do I know if my friend really put a HardSPL on my cell the first time. I know that one way to tell was through MTTY and boot command, but my cell didn't respond to that. My friend said he put a HardSPL on; would doing it again hurt anything?
big3 said:
hey everyone, My phone is temporarily working at this point!!!
My new question is, how do I know if my friend really put a HardSPL on my cell the first time. I know that one way to tell was through MTTY and boot command, but my cell didn't respond to that. My friend said he put a HardSPL on; would doing it again hurt anything?
Click to expand...
Click to collapse
Put your phone in bootloader mode and if it says "hard" next to "SPL:" it's got a hrd SPL version.
Ta
Dave
I am trying to flash a HardSPL to my phone; the computer see's the device but will not allow me to copy any files to it. When I go though the sync center, it begins to connect then says error. What should I do?
big3 said:
I am trying to flash a HardSPL to my phone; the computer see's the device but will not allow me to copy any files to it. When I go though the sync center, it begins to connect then says error. What should I do?
Click to expand...
Click to collapse
Try copying them via the SD card using a card reader if you have one.
Ta
Dave
tryd that, all it does is say loading and pretty much stays there indefinately.
Right, lets take a step back...
You don't have Hard SPL at the moment?
If not, the best guide for flashing Hard SPL is here : http://forum.xda-developers.com/showthread.php?t=433835
Follow through what mskip advises and let me know if you get stuck and at what point.
Ta
Dave
I get stuck at the very first step were you are supposed to copy the 3 different JumpSPL files. I even tried copying a word document and it said "the file Reference could not be copied. It may not exist or cannot be transferred."
My computer can access the phone, but I cannot transfer anything to its memory. I also tryed copying it to the sd card while it is in the phone and it gives me the same error. Active sync whont work either, just keeps saying error.
big3 said:
I get stuck at the very first step were you are supposed to copy the 3 different JumpSPL files. I even tried copying a word document and it said "the file Reference could not be copied. It may not exist or cannot be transferred."
My computer can access the phone, but I cannot transfer anything to its memory. I also tryed copying it to the sd card while it is in the phone and it gives me the same error. Active sync whont work either, just keeps saying error.
Click to expand...
Click to collapse
Try deleting and re-creating the partnership... Do you have Office installed, this might stop if working.
Do you have a Card Reader, put the card in there and put the files on the card that way.
Failing that MyMoblier let's you copy files, I think it works differently to AS.
Dave
i have deleted the partnership and created a new one, and it doesnt work. As for mymobiler; the website will not load for me on either my desktop or laptop.
one thing i just tryed which was interesting was to load the 3 JumpSPL files onto the sdCard and then copy them to the phone's main memory. It wouldnt allow me to do this. How do I remove the read/write protection on the phone?
big3 said:
Hey guys,
I am going to start by saying that I have read almost every single sticky, thread, wiki and anything else I could get my grubby hands on to try and solve my problem; but I fear I may have missed something, or done it wrong.
Now to my problem. My friend who had the same phone as me did a HardSPL flash a long time ago and gave me some new ROM. It worked for awhile but wasn't great so we changed to a different ROM. After awhile I got sick of this one and all of its bugs so about 3 days ago we got some with windows 6.5; unfortunately something happened; causing it to be highly unstable, so we switched AGAIN.
Now to my problem. It will not boot. If I just let it boot without doing anything *or if I hit keys* it goes to an hTc TyTn2 screen with the R; G; and D displayed. I tried to flash it via Micro sd card but all I get is a white screen with blue "loading..." and nothing; it will sit there indefinitely. I have been following cmonex's instructions to a "T" and I am stuck. I attempted to do the USB route and the phone will display the tri-colors and say USB, but my computer *Vista* isn't seeing the phone. I tried different USB ports etc. and nothing. Please let me know what you guys think; anything would be greatly appreciated.
~big3
Click to expand...
Click to collapse
did you ask this question in those threads? i just searched all your posts and im not seeing where you asked in those threads before you started a new thread.
didn't see where you tried to flash stock rom either, i recommend trying to flash it, and flash stock before you flash any cooked roms.
i never said I did any of the flashing. my friend did it all, and he claims to have done the hardspl. he then loaded new ROM onto the phone. Since he is no longer around, and everything has gone hay-wire, I am trying to fix it.
Here is my new situation; I can get the phone to fully load into the rom, but it does not have the HardSPL installed. The computer will recognize that the phone is plugged in, but active sync will not connect; just says error. If i go through "my computer" and try and copy files that way it says: "the file Reference could not be copied. It may not exist or cannot be transferred." I have tried to just re-flash it *because i really need it up and running* and the programs just say they cannot. I even used CID unlocker and it says it failed. I just don't know where to go from here.
Try doing a Hard Reset and see if your symptoms change. NOTE: Remove the SD Card.
Hi, i must be the dumbest person in here. I just bricked my used sprint touch pro 2. Well it all started when i did not get any sleep, and did not paying attention. My phone was fully unlocked. So i decided i could not wait to flash my phone. So i started to flash the phone, but after it was done i realized i only flashed the BLEEPING SPLASH SCREEN !!!!!!!!
So when i tried to turn the phone on, it loads to the splash screen only.
So i tried to connect it to my computer, but nothing. So i tried to hard reset, it goes to bootloader screen, then only to Touch pro 2 screen. Is there anything that i could do beside Cry, lol. HELP PLEASE.
Can you enter bootloader on your touch pro2?
If so, then its good news and its not bricked Download an official rom from HTC website (or here from the touch pro 2 forum), connect it to your computer whilst in bootloader (multi coloured screen) - make sure is says usb and not serial on ur devices screen and double click your downloaded rom.
It should flash succesfully and you will have your device back up and running in under 10 minutes.
Good luck.
Maybe i should elaborate more. when i said, when i connect it to the computer nothing. I meant nothing happens. Meaning it does not connect, or recognize the Usb, or computer. Help, THX
Ok, you know how to get ur device into bootloader right? what does it say on the screen (dont bother connecting it to your computer).
It jumps right from bootloader mode to the screen that ask me if i want reset all setting to manufacturer default, or cancel page.
soft reset = hold the power button and the volume button down and softreset
I think you are trying to to a hard reset
If you can stay in bootloader, it is possible to flash official stock rom from your sd card. It isnt too difficult to do so let me know and ill tell you how to do it, but have a look on the touch pro 2 forum, you will find how to do it there
Okay, i did a soft reset. And it is staying at the boot loader screen. So it is possible to fix this sprint phone?
Okay, i think i have an idea what you want me to do. You want me to put the phone in boot loader mode, then down load a .nbh file onto the root of the SD card. And while in boot loader mode it should flash the stock rom.
Is that correct?
Yes exactly that
Make sure you extract the nbh file from the stock rom using winzip or another utility. You must then rename it to something like xxxxx.nbh (you will need to get this from the tp2 forum or when i have time ill find it for u). COpy it to the root as you say, enter bootloader etc etc.
You will find how to do this in the tp2 forum.
Good luck.
Once you get into the bootloader (the tri-coloured screen) it should say "Serial" at the bottom. Then plug the USB cable in from your PC, and that should change to "USB".
If it does say "USB", then you should be able to go ahead and flash a ROM from the PC (no need to do it via SD unless you really want to). You don't need an ActiveSync connection.
Omg. I love you guys. You guys are the best in the whole amm world. I will be donating shortly. Thank you so much. It worked perfectly in boot loader mode to connect it to the usb. Than i was able to download the stock rom.
Now should i hard reset it or just leave it alone. Thanks a million.
Hey, good news.
I guess when you said before that it didn't say usb whilst in bootloader was because you weren't actually in bootloader no matter.
Glad you got it back up and running without having to flash via sd
If you flashed an official stock rom, don't bother hard resetting, no point, if you flashed a custom or cooked rom then normally advisable to HR after a flash but this does depend on the rom.
Cheers.
I had a StockSpl on my Htc touch pro and I wanted to flash an unsigned Hard-SPL from my MicroSD because I wasn't home and I didn't have the USB cable. After the screen loaded 100% the device restarted I took off the MicroSD and now it keep showing this tri-color screen:
RUUNBH
RAPH100
SPL-1.90.000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
Upgrade ROM code error
Please try again
Serial.
(I've also attached a picture)
If i try to flash again from MicroSD the same HSPL it loads until 100% then restart and start to load again until i get the MicroSD card off. Or if i try to flash other StackSPL or any other ROM it stays on Loading on a grey screen.
After I went home I tried to flash the HSPL again from my computer using the USB cable, it start to load 0% then it does nothing. I've tried to flash StockSpl and other ROMs from the computer too but it does the same.
I think i've tried anything but nothing seems to work ... if someone can help me pls ... i've searched the entire forum and there's someone that had almost the same problem here: http://forum.xda-developers.com/showthread.php?t=566796
but noone had any solutions.
You can't flash hard spl off your sd card; it's got to be done through a usb cable.
Just read through the hard spl thread; it's long, but your situation has probably been addressed. I did it almost 3 years ago, so I don't remember the tricks. That's the case with most posters, I'm afraid. Just read the thread.
can u pls tell me which thread?
this one?: http://forum.xda-developers.com/showthread.php?t=410150
or this one?: http://forum.xda-developers.com/showthread.php?t=448008
Either, but read the first one. You can also look in the unlocker thread. Hell, you may just want to buy the unlocker and run that. It will flash hard spl, and the directions may be better.
I just hope they aren't trying to HSPL(hard SPL) a CDMA device :S I've made the mistake to assume the person that was posting in this forum had a GSM device and they really screwed up after a third attempt at flashing HSPL!
Usually if I have a difficult time flashing my Fuze or TP(both GSM), I remove everything to include the battery, connect the USB to an available USB port on the computer then hold the volume down key while connecting the device to the USB cable. Probably not the most friendly way but it certainly will tell you if there is a problem with your USB port/cable or even device!
My htc raphael is GSM
I've tried to hold the volume down button but it's always the same
There's no problem with the cable just that I can't flash anything because I'm stuck with a stock-spl and I can't flash a hard-spl either. When I try to flash something from the computer it starts to flashing with 0% then nothing happends until the RUU gives me the 262 Error. And when i try to flash from my mSD it just stuck with a Loading screen.
Xadow said:
I had a StockSpl on my Htc touch pro and I wanted to flash an unsigned Hard-SPL from my MicroSD because I wasn't home and I didn't have the USB cable. After the screen loaded 100% the device restarted I took off the MicroSD and now it keep showing this tri-color screen:
RUUNBH
RAPH100
SPL-1.90.000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
Upgrade ROM code error
Please try again
Serial.
(I've also attached a picture)
If i try to flash again from MicroSD the same HSPL it loads until 100% then restart and start to load again until i get the MicroSD card off. Or if i try to flash other StackSPL or any other ROM it stays on Loading on a grey screen.
After I went home I tried to flash the HSPL again from my computer using the USB cable, it start to load 0% then it does nothing. I've tried to flash StockSpl and other ROMs from the computer too but it does the same.
I think i've tried anything but nothing seems to work ... if someone can help me pls ... i've searched the entire forum and there's someone that had almost the same problem here: http://forum.xda-developers.com/showthread.php?t=566796
but noone had any solutions.
Click to expand...
Click to collapse
Naughty Naughty..
I guess you realise now that you should ALWAYS read read read before modifying your phone in any way.
What EXACT file did you originally flash to your phone via microsd card and where did you get it from?
If you go into the bootloader screen and then connect the usb cable does it show "usb" at the bottom of the screen?
PLEASE STOP TRYING TO FLASH HARDSPL FROM MICROSD AS YOU CANT DO IT. If you could then it would be in my guide..
Mark.
mskip said:
Naughty Naughty..
I guess you realise now that you should ALWAYS read read read before modifying your phone in any way.
What EXACT file did you originally flash to your phone via microsd card and where did you get it from?
If you go into the bootloader screen and then connect the usb cable does it show "usb" at the bottom of the screen?
PLEASE STOP TRYING TO FLASH HARDSPL FROM MICROSD AS YOU CANT DO IT. If you could then it would be in my guide..
Mark.
Click to expand...
Click to collapse
Thanks for replying
Yes ... I did read the part with the SD flashing but i thought it's not a bit deal to flash from mSD since the flashing via activesync is so easy.
Well ... i extracted the RUU_Signed.nbh from the Hard-SPL found HERE and i copied it to the mSD (MicroSD) and renamed it RAPHIMG.nbh.
I restarted my phone holding the volume down button and it started to load until 100% then it restarted and showed the bootloader screen and after a couple of seconds start to flash the HSPL again so after it completed 2 or 3 times of flashing and restarted i took the battery and the mSD off (I DIDN'T TOOK THE BATTERY WHILE IT WAS IN THE PROCESS OF FLASHING). And when i started the phone again without mSD it showed the bootloader screen like it was waiting to get a .nbh file on mSD to start flashing again.
No matter what i do my phone start in bootloader and down it shows "Serial". If i connect the usb it shows "USB".
I tryed to do a hard reset and it seem to work but after it finish and the phone restarts is stuck with the same tri-colour screen.
Sry for trouble and thx again
I guess I missed the part in the OP where you said it was stuck in bootloader. That's not good. I would try flashing the stock raphael rom (assuming you have it). Have you tried that? I dunno, you may be stuck for good.
Xadow said:
Thanks for replying
Yes ... I did read the part with the SD flashing but i thought it's not a bit deal to flash from mSD since the flashing via activesync is so easy.
Well ... i extracted the RUU_Signed.nbh from the Hard-SPL found HERE and i copied it to the mSD (MicroSD) and renamed it RAPHIMG.nbh.
I restarted my phone holding the volume down button and it started to load until 100% then it restarted and showed the bootloader screen and after a couple of seconds start to flash the HSPL again so after it completed 2 or 3 times of flashing and restarted i took the battery and the mSD off (I DIDN'T TOOK THE BATTERY WHILE IT WAS IN THE PROCESS OF FLASHING). And when i started the phone again without mSD it showed the bootloader screen like it was waiting to get a .nbh file on mSD to start flashing again.
No matter what i do my phone start in bootloader and down it shows "Serial". If i connect the usb it shows "USB".
I tryed to do a hard reset and it seem to work but after it finish and the phone restarts is stuck with the same tri-colour screen.
Sry for trouble and thx again
Click to expand...
Click to collapse
As Farmer Ted said your best bet now is to download your ORIGINAL Rom (from your provider) and flash it from your pc with the usb cable attached. The phone had to be in SSPL mode before running the RUU which is why everything was packed in a single exe. You may have corrupted your SPL in which case you have bricked your phone but if you can manage to flash a Stock Rom then the Stock SPL should be reflashed and you can start again with the HardSPL by following the CORRECT instructions and not making up your own lol.
Good luck.
Mark.
When i bought my phone, the first thing i did was to dump the rom. So now i rebuild it from raw and tried to flash but it didn't work so i went to Orange site and i downloaded the official ROM then started to flash and ... IT WORKS
I think that the ROM was corrupted not the SPL, and since the SPL was stock it didn't allow me to flash other ROMs other then the official
Thanks for all guys I couldn't done this without your help
P.S: why did it allowed me to flash the official rom but the hspl not?
It didn't flash the hard spl because you did it all wrong; those rebuilt roms aren't exactly the same as the stock roms, so it's not surprising that wouldn't flash. Good job finding the original shipped one, though.
Now, just read mskip's instructions and you should be good to go. I think the trick is just to enter bootloader, then connect to your pc through the usb cable.
Hi, I recently updated MangoB2, and it was working fine, but I tried to play a video and it froze and went off, and came to connect to PC screen, and when I try to restore, it shuts the phone off and it restarts the phone. Plus, it also can't recover using windows phone support tool, please help!!!
CoffeeM said:
Hi, I recently updated MangoB2, and it was working fine, but I tried to play a video and it froze and went off, and came to connect to PC screen, and when I try to restore, it shuts the phone off and it restarts the phone. Plus, it also can't recover using windows phone support tool, please help!!!
Click to expand...
Click to collapse
My first question is, is there any ROM's available for your device. If so, boat into the tri-color screen & try flashing a ROM. Also, have you tried Hard resetting your device.
Yes I did try to hard reset, but it does it quickly, and says to restart my phone, and my phone is HTC T8788, also when i try to restore in Zune it stops at 16%,
CoffeeM said:
Yes I did try to hard reset, but it does it quickly, and says to restart my phone, and my phone is HTC T8788, also when i try to restore in Zune it stops at 16%,
Click to expand...
Click to collapse
Did you try booting into the Tri-Color Screen & flashing one of the ROM's from here?
Hold Volume down & press power, keep holding volume down until you see the tri-color screen (red/blue/green/white), when connected to PC it'll say USB at the bottom & windows should install a new driver. Than you run the flashing program from one of those threads.
I can't do it, it doesn't work, now it freezes on HTC white screen, and doesn't connect to restore either,
Nobody is going to help you if you aren't trying suggestions.... It should most definatly go into bootloader... It won't even have a chance to freeze nothing loads at that point.
Sent from my HD7 using XDA Windows Phone 7 App
I did try to flash, but this only works, RUU_Mondrian_Cingular_US_1.03.502.07_5.51.09.06_22.30.50_RELEASE other ones I get [error] 208, but still it get stuck at HTC screen, is it because I have to have nk.nbf file, if so can anyone tell me where and how I can get it working, I tried all night and still trying to fix, I really need it working!
The phone still gets stuck at HTC screen, even after flash, I tried everything, could it be because I have Windows Phone 7.5 Beta 2 in there.
CoffeeM said:
The phone still gets stuck at HTC screen, even after flash, I tried everything, could it be because I have Windows Phone 7.5 Beta 2 in there.
Click to expand...
Click to collapse
If it's still getting stuck, maybe you have a faulty SD Card or the ROM chip got corrupted somehow. You may have to send it in under warranty. My only other suggestion would be to try RSPL or HSPL (HSPL void warranty) & than try flashing a ROM again if RSPL/HSPL supports your model of the HTC Surround. I'd suggest RSPL as it's temporary & won't cause any warranty issues.
Instructions:
1) Boot into Tri-Color Screen with Volume down feature.
2) Connect to USB to PC.
3) Wait for Windows to install new hardware driver. (Should be done already as you tried flashing already)
4) Run DFT_RSPL_WP7FG1_LAUNCH.exe from ZIP attachment in thread linked below.
5) Wait for your device to reboot back into Tri-Color Screen on it own.
6) Flash ROM. Optionally, flash HSPL with DFT_HSPL_WP7FG1_INSTALL.exe from same zip, than flash the ROM.
NOTE: Using HSPL flashes it to ROM & if you are having hardware issue, this could completely brick the device. So, proceed with caution!
[DFT] HSPL / RSPL for HTC WP7 First Generation
It wouldn't be because of the Mango Beta, flashing the ROM should of reformatted the ROM chip & SD Card, erasing Mango.
I have the same problem, still gets stuck on HTC screen, could it be the SD card is not working, I try to put in restore so I can restore it starts normally but when it restarts the phone to continue to restore it gets stuck at HTC screen, and is there a way to check to see if the SD card is OK.
CoffeeM said:
I have the same problem, still gets stuck on HTC screen, could it be the SD card is not working, I try to put in restore so I can restore it starts normally but when it restarts the phone to continue to restore it gets stuck at HTC screen, and is there a way to check to see if the SD card is OK.
Click to expand...
Click to collapse
To check the SD Card, you need a Nokia device. Nokia devices can format WP7 SD Cards. Nothing else will recognize the format WP7 uses. Plus, you have to open the device up to get it out, which in most cases will void your warranty. One of the screws has a void sticker on it & if your try removing that screw, your warranty is void as they can see you tried removing the screw by the sticker being missing or damaged.
If possible, list all software I can try to restore or fix, or tweak to make work or reset something in the phone to work! Anything at all!
That's no problem for me, I bought from a friend! I have nothing to lose. And do you know the software to format the SD disk!
Oh wait, are you trying to restore after successfully installing a new ROM?
If so, don't restore, the restore isn't compatible anymore. You can reinstall all apps by finding them in the marketplace again (on device, not ZUNE PC). As long as you use same live ID on setup, the apps should be read as purchased.
CoffeeM said:
That's no problem for me, I bought from a friend! I have nothing to lose. And do you know the software to format the SD disk!
Click to expand...
Click to collapse
In order to format the SD Card, you need a Nokia Cell. I believe it's their meego/Symbian OS that can find the card. Hopefully you or a friend has one. Lucky for me my roommate has a Nokia Nuron if I ever needed to do this.
So I can't restore it anymore since I install new boot loader. Or it doesn't matter.
CoffeeM said:
So I can't restore it anymore since I install new boot loader. Or it doesn't matter.
Click to expand...
Click to collapse
Bootloader doesn't matter, if you flash a new ROM, it does as the restore won't be compatible with the new ROM. The restore must be made from the current ROM at least to my knowledge. It could be that maybe the restore is corrupt even.
There is also a tool that lets you do it in Windows. It was by Samsung or something. I'll try to find it and post it in here.
drkfngthdragnlrd said:
In order to format the SD Card, you need a Nokia Cell. I believe it's their meego/Symbian OS that can find the card. Hopefully you or a friend has one. Lucky for me my roommate has a Nokia Nuron if I ever needed to do this.
Click to expand...
Click to collapse
Sent from my LG-P999 using XDA App
drkfngthdragnlrd said:
In order to format the SD Card, you need a Nokia Cell. I believe it's their meego/Symbian OS that can find the card. Hopefully you or a friend has one. Lucky for me my roommate has a Nokia Nuron if I ever needed to do this.
Click to expand...
Click to collapse
a sony psp will also do this, provided you have the microsd to mspd converter.
But, why doesn't it work after flash, after many attempt still gets stuck at HTC screen, the phone is probable not repairable right, or there still may be a chance for me to get it back again!