I accidentally put The Orange SPV E650 ROM onto my unbranded HTS S710 instead of onto my SPVG E650 and am now unable to Flash it with the WM6.1 ROM that I had on in the past. SDA Application unlock says that the Phone can not be unlocked, does anyone know how to enable me to re-flash WM 6.1 onto my Vox?
Roland
exactly same happened to me, tried best but failure, had to take service center and pay 500 INR to get rid of this.
I am assuming you didn't flash uSPL to the device? You should be able to reflash it with an official ROM, uSPL and then your 6.1 ROM.
That is because the ROM of SPV E650 needs more steps to unlock it
I also have had experience with this ROM and found below steps to unlock it
1- Copy SP_AllowCertificateInstall.cab to your phone, Install it & reboot
2- Connect your phone to your pc with active sync. Click on SDA_ApplicationUnlock, reboot
3- And install PHMRegedit.cab to the phone. Open this Registry Edit and
navigate to HKLM\Security\Policies\Policies\
Click "Values" soft-key
Change "00001001" value to 1 (decimal) (recovery note: default is 2)
Change "00001005" value to 40 (decimal) (recovery note: default is 16)
Reboot device.
4- Now you can flash your phone with any ROMs (follow normal steps as instructions)
Just in case your phone still cannot be unlock, open Registry Edit and follow this
1- Navigate to HKEY_LOCAL_MACHINE/Security/Policies/Policies,
2- Value, Menu : New Value, DWORD, Value name : 0000101b, Value data : 1, Base : Decimal, Value type : REG DWORD,
3-Done. Reboot your phone
4- Flash with your favorite ROMs
Above is my experience with my 2 phones (Orange SPV E650 & HTC S710). Use this instructions at your own risk !
Good luck !
That Worked nicely, just app unlocked my S710 and flashed USPL to 1.35 and applied the IPL 1.35 patch.
Roland
Related
I have an spv c600 rom version 2.0.14.0 op version : 11.2.1.8.
All you need: 1 Orange Sim
To unlock do as follows:
1) go to http://spvunlock.rd.francetelecom.com/ and follows the steps (phone number may be fake, but imei has to be correct). You will receive a cab file in your mailbox. I got mine in half an hour, but it could take longer.
2) copy it in your phone and execute it
3) copy and execute cert.cab on your phone
4) execute spvservices.exe on your pc to remove sim lock and cid lock
Easier than expected. No need to boot strange modded roms or edit nbf files.
This is a patched SPL for HTC Elf devices (HTC Touch / HTC P3450 / Dopod S1, o2 Nova, etc...).
This SPL is based on original Elf 1.11 SPL but includes 3 patches:
g_cKeyCardSecurityLevel = 0 (set 32)
Does not check Model ID
Does not check signature*
(*) code must be formally signed i.e. contain properly-formated signatures on their places, however no checking are performed against them.
This means you can flash ANY ROM to your Elf after flashing USPL on it, no need to pay for CID unlock anymore!
Disclaimer:
This is free to use but at your own risk, I take no responsibility for any conflict, fault, or damage caused to your phone by this unlocking procedure. No warranties of any kind are given. Any commercial usage prohibited.
Instructions:
1. Unzip
2. Connect your phone to computer, make sure activesync is enabled (green icon)
3. Run elf-uspl.exe on your computer and follow instructions on screen:
Code:
*************************************************************
Please make sure Activesync is enabled (green icon in systray)
and hit ENTER to start...
STEP 1/3......50%......75%....100%
The next step will load a patched bootloader (SPL) on your device
it will make your device temporary SuperCID (seclevel=0), and will
avoid modelID and signature checking when flashing NBH files.
Hit ENTER to continue...
STEP 2/3.....15%.....25%...50%...75%.....100%
Phone screen should now be blank and the activesync icon gray
if not, the loading procedure has failed and you'll have to repeat again.
If all was OK hit ENTER and the standard "PDA Phone ROM Update Utility"
window will start, allowing you to flash patched SPL on your device.
Hit CTRL+C to Cancel or ENTER to continue...
Follow the steps on the wizard to flash the patched SPL, when this
step completes your device will reboot.
STEP 3/3 - Launching RUU, please wait...
Process is finished, congratulations!
If you find it useful don't forget to donate :)
*************************************************************
(c)2007 pof - XDA Developers
Hit ENTER to quit.
Update:
Some ROMs (specially O2 Nova) don't allow to run unsigned applications by default and some people have reported difficulties installing USPL. If you see a popup asking to run unsigned code, you need to rapi-unlock your phone manually, to do this download enable-rapi.zip and follow the instructions inside the file prior to installing USPL.
Notes:
1. I have only tested under XP, people says it works on Vista too.
2. Unzip the file, do not run it on the zipped folder. (Note: Better to unzip in c:\ folder with no spaces on the name).
3. This will only CID unlock your device, not SIM unlock.
4. On some devices STEP 2 fails the first time, just hit CTRL+C, softreset your device and start over again.
5. To create NBH files for Elf you should use HTC Rom Tool by Dark Simpson, because "nbhgen" doesn't create proper NBH files for elf.
6. You can use Artemis splash screen tool by jcaron safely on the Elf, the Artemis RUU is compatible with Elf-USPL and both devices have same splash screen format.
7. After flashing a full ROM (containing a SPL on it) you'll overwrite USPL, so you'll need to repeat the USPL flashing process again.
8. If you like it, use the paypal donate button on my signature
Enjoy!
UPDATE (thanks Noonski)
TO AVOID BRICKED ELF BE SURE TO CHECK THIS THREAD:
http://forum.xda-developers.com/showthread.php?t=320155
So new users can first check if their Shipped rom is around before taking the decision to flash USPL.
Also this makes them aware to submit new ones to the list.
And if they Get stuck with a 270 Error at 3% without actually having an original, it was they that made the decision themselves.
Thank you so much! Free CID unlock finally!
Congratulations!!!!
Work in HTC Herald ???
[]s FerSoft
fersoft said:
Work in HTC Herald ???
Click to expand...
Click to collapse
No, this one is only for Elf, but I'll publish a version for Herald soon, its on testing phase
Execellent and will try it right the way...thanks a million....
i did not get what you are saying
This will only CID unlock your device, not SIM unlock
can you please explain me in simple words after after using this tool on my HTC Touch can i use the sim from different service provider
Cool! I finally could update my Spanish Elf to the latest Dopod Asia ROM (WWE)
Thanks!
Greate! I just flash it successfully!
BTW:
pof:How can i flash the device that can not boot? my friend's device only boot in 3-color mode.
Great.. Thank Pro :-*
arifdreamworldera said:
i did not get what you are saying
This will only CID unlock your device, not SIM unlock
can you please explain me in simple words after after using this tool on my HTC Touch can i use the sim from different service provider
Click to expand...
Click to collapse
in simple words: No
there are two different areas in the ROM.
One regarding CID and one for SIM-Lock.
Works perfect in Windows Vista Ultimate 32bit.
Thx pof!
THNX!!!!
THANX a lot pof!!!
You will get a donation from me!
(as I promised here for Excalibur)
Am I right that I can also backup my original ROM and flash it back with that tools?
Thanks And Working Fine With Me .
Great job pof
Oh that's great news for all users HTC Touch,thanks a lot.
This is fantastic! Thanks pof!
Took me 3 attempts, but it worked out great (Vista didnt work though, XP did the third time )
Edit: My dutch Touch, is now a WWE Touch! Thnx again pof. Awesome work.
No success
I went through steps 1 and 2. Then started the RUU with the ELFUSPL hack from pof. But it always gives me the message "[270] UPDATE ERROR" and "Image file is corrupted". I downloaded it again from pof - no change.
Now I wonder if:
1. Is it ok if the ActiveSync icon remains gray (not connected) after the step 2 and during the step 3?
2. Is this method not appropriate for O2 Nova (German)?
Don't know what to do now. Would anyone be so kind and give me any hints, please?
----------------
O2 Nova, German version
How can i see my default settings ?
CID locked or CID unlocked ?
Or all Touch CID Locked default ? ( and i need this flash if i have upgrade "any" rom )
Thx all of your answers !
Follow the steps on the wizard to flash the patched SPL, when this
step completes your device will reboot.
Click to expand...
Click to collapse
this must be a typo then
thanks for sharing the information !
I dont think its a typo. The wizard regards the setup wizard, which is the series of checklist that you go through to get to the end desired result.
Kaiser Sim Unlocker v0.1
========================
Brought to you by jockyw2001
(c)2008 jockyw2001
You definitely save money by using this unlocker, so consider a donation for me to keep the R&D going
Click here to send your PayPal donation.
Download links:
Rapidshare
Megaupload
Note for WM6.1 users
================
Do not try this on 6.1! You will need to downgrade to 6.0
Note for Vista users
===============
This guide will explain how to change your drivers to the xp. You will have problems running the unlocker otherwise. Log in as administrator if you run the ROM update tool and unlocker. That also applies to XP users.
Instructions
============
(The instructions below take preference since they are more current than the readme in the package)
1. To verify you have installed the right HardSPL do this: power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-color screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.27.14.09"). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. You can download radio roms from XDA devs here.
3. Connect PC and Kaiser with a USB cable and keep it connected until the last step.
4. Power on the Kaiser and let it boot into Windows Mobile. On the PC make sure the activesync icon is green
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run KaiserCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished.
Note that you can also skip step 6. and proceed with step 7.
6. Power off your Kaiser and insert a 'strange' SIM, i.e. a SIM from another provider than the one your phone is locked to.
7. Once Windows Mobile has booted up it will (usually after you have entered the usual 4-digit PIN) show a window called "Simlock" and a textbox where you can enter a 8-digit unlockcode. Now perform a soft reset by pressing the reset button *but* at the same time keep the camera button pressed. If you did it well you will be back in bootloader mode and you see the tri-color screen. The best technique is to press and hold the camera button first and then shortly press the reset button with the stylus.
8a. right-click activeync icon and uncheck "Allow USB connections" from Connection Settings
8b. On your PC go into the "step2" directory and run "kaiser-simunlocker.exe". If all went well you will see the unlockcode on your monitor and your Kaiser is being restarted automatically.
8c. right-click activeync icon and check "Allow USB connections" from Connection Settings
You should see this:
Code:
=== Kaiser Sim Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to [email][email protected][/email]
Your Unlockcode = 12345678
[] Done, enter the unlockcode
[] And then flash your original radio
Press Enter to exit
Note: If you skipped step 6 then you should now also skip step 9. and continue with step 9x
9. Once Windows Mobile has booted up it will again show the "Simlock" window. When prompted (usually immediately after you have entered the usual 4-digit SIM PIN), enter the the 8-digit unlockcode and your phone is permanently SIM unlocked
Now proceed to step 10.
9x. (Only if you skipped steps 6. and 9.): Run \windows\simlock.exe on your Kaiser and enter the 8-digit unlockcode when you are prompted.
In order to see simlock.exe you have to open file explorer then click menu > and show all files. If you can still not find simlock.exe copy the attached one to the phone's "My Documents" directory and run it from there.
10. Download the original radio from here to the "step3" directory on your PC and flash it with KaiserCustomRUU.exe
That's all folks
Now you can look forward to some other great tools which I will release soon: "Kaiser SuperCID" and "Kaiser Radio Dumper"
Enjoy and ... donate to keep R&D going! Thx!
JockyW
Credits
=======
* Tom Codon and unkown for testing
* des, pof and olipro for SSPL and HardSPL
* arc and all the other great minds at XDA devs
* viperbjk, adfree and all other QC hackers at Modopo
* PURESKILLZZZ for supplemental instructions here
(c)2008 jockyw2001
[email protected]
Jan 19th 2008
Thanks jockyw2001... trying now, will post feedback
Thanks! Appreciate it: I thought it was just a hype, trying....
Just unlocked...Thanks!!
WoW! Great job JockyW!!!!
Will try it out when I get home!
Nice works my friend...!
Keep up it and don't forget supporting niki device
great great and greater
il conna try it by first daylight thanx and great affoert regards
Great!! Thanks!! Keep up the good work!
gonna try as soon as my battery is over 50%.. will post result
THNX MAN
Instructions followed to the letter here and no dice. At step two i get an error, it reads: "\\.\WCEUSBSH001: No such file or directory cannot connect"
Any help would be appreciated, my OS is Vista Ultimate x64.
kamikaze_decoy said:
my OS is Vista Ultimate x64.
Click to expand...
Click to collapse
Bug detected !!!
Can it apply to all models? such as UK...Thanks...
kamikaze_decoy said:
Instructions followed to the letter here and no dice. At step two i get an error, it reads: "\\.\WCEUSBSH001: No such file or directory cannot connect"
Any help would be appreciated, my OS is Vista Ultimate x64.
Click to expand...
Click to collapse
See if u can find a PC with XP
I stay far away from Vista and never tested it on Vista.
But maybe this helps.
bwqipzbpd said:
Can it apply to all models? such as UK...Thanks...
Click to expand...
Click to collapse
Yes, and goodluck!
Can I use different radio since my original radio is not available for download (my original radio is 1.27.12.29) ?
I use a Kaiser on the UK Orange and I have flashed my phone to Dutty's Rom.
Thank you so much.
Im a UK Orange user. When I spoke to HTC a few months back, the guy I spoke to suggested that Orange are actually using a modified version of the radio rom.
Has anyone using a Kaiser on the UK Orange tried a different radio rom?
Or has the UK Orange radio rom actually been dumped, so we can upload go back to it after unlocking our "beautifully powerful phone"
benz710 said:
Can I use different radio since my original radio is not available for download (my original radio is 1.27.12.29) ?
Thank you so much.
Click to expand...
Click to collapse
You can, but each radio has it's pros and cons. Maybe you should wait until I release my radio dumper. No release date for it yet, but I think in 1-2 wk
i have a question on last step where u have to flash back your radio in "step3 folder", for example, if i need to flash back KAIS_Radinly_1.27.12.17_CustomRUU, but in this zip file has CustomRUU.exe and RUU_signed.nbh, should i put this two files in to "step3 folder", and then click on KaiserCustomRUU.exe (step3 folder). OR it doesn't matter which *.exe files i click, because they are same files, but different filename.
waichai said:
i have a question on last step where u have to flash back your radio in "step3 folder", for example, if i need to flash back KAIS_Radinly_1.27.12.17_CustomRUU, but in this zip file has CustomRUU.exe and RUU_signed.nbh, should i put this two files in to "step3 folder", and then click on KaiserCustomRUU.exe (step3 folder). OR it doesn't matter which *.exe files i click, because they are same files, but different filename.
Click to expand...
Click to collapse
If KAIS_Radinly_1.27.12.17_CustomRUU is a .exe then delete KaiserCustomRUU.exe and run KAIS_Radinly_1.27.12.17_CustomRUU.exe
Hi,
On Step2 it give the error:
\\.\WCEUSBSH001: Permission Denied
cannot connect to \\.\WCEUSBSH001
I'm using XP SP2.
Any sugestions ?
jockyw2001 said:
If KAIS_Radinly_1.27.12.17_CustomRUU is a .exe then delete KaiserCustomRUU.exe and run KAIS_Radinly_1.27.12.17_CustomRUU.exe
Click to expand...
Click to collapse
jockyw2001,
is that mean i don't have to use file in "step3 folder" file?
hi there ..... i'm newbie here, i've upgraded my O2 mini from WM 2003se to WM 6.1(WWE_02 then WWE_03) succesfully, but now i want it back to WM2003se, i did an Uninstallation on WM6.1(WWE_03), but it just went from WWE_03 to WWE_02, i could never get it back to WM2003se.
is there any advice for me to get it done???
please help......
Download the wm2003se ROM and then follow the cotulla's instruction
Uninstallation
*Enter bootloader mode on device (Press POWER + CAMERA + RESET, you will see Serial/USB at top and 1.0X at bottom)
*Connect via USB to PC
*Install ORIGINAL 1.12 or 1.13 ROM. No big storage etc. Install original one!!
[YOU *MUST* REPLACE ROMUpgradeUt.exe TO MaUpgradeUt_noID.exe]
*Now you can flash any other old custom roms.
NOTE: This is ONLY ONE right instruction how to uninstall my rom, otherwise you can have problems with new rom.
kudtz said:
Download the wm2003se ROM and then follow the cotulla's instruction
Uninstallation
*Enter bootloader mode on device (Press POWER + CAMERA + RESET, you will see Serial/USB at top and 1.0X at bottom)
*Connect via USB to PC
*Install ORIGINAL 1.12 or 1.13 ROM. No big storage etc. Install original one!!
[YOU *MUST* REPLACE ROMUpgradeUt.exe TO MaUpgradeUt_noID.exe]
*Now you can flash any other old custom roms.
NOTE: This is ONLY ONE right instruction how to uninstall my rom, otherwise you can have problems with new rom.
Click to expand...
Click to collapse
thank you... i've read the manual instruction too, but could anyone give me link where i can download wm2003se ROM?????
sorry my mistake,.....double post
use magician wiki
http://wiki.xda-developers.com/index.php?pagename=HTC_Magician
Dear forum members,
In the following A, B, C and D sections is described the flashing process
of the Non NoDo unbranded ROM: RUU_Spark_Vodafone_FR_1.09.707.07_Radio_5.50.09.15_22.23.50.09U_by_ansar
This is an 7004 based platform ROM and can used for chevron unlock
It supports the following keybord languages:
English (United States), French (Canada), French (France), French (Switzwrland)
German (Germany), Italian (Italy) and Spanish (Spain - International)
A. Pre-Requisites
If your Tropy 7 is flashed with the ROM of the following release:
1. RUU_Spark_Vodafone_FR_1.08.161.01_Radio_5.50.09.15_22.23.50.09U
then you can flash the following Non NoDo unbranded ROM and when you like you can comeback to your previous ROM
In case your Tropy 7 is flashed with a different of the above 1 ROM but your Firmware version at your phone settings>about>more information
is of the form xxxx.yy.zzzzz.161 i.e. with characteristic value 161
then you can also flash the following NoDo unbranded ROM, but you can comeback only to one of the above 1 ROM
B. Downloading
You must download the following 2 ROMs:
1. Download this zip ROM file: RUU_Spark_Vodafone_FR_1.09.707.07_Radio_5.50.09.15_22.23.50.09U_by_ansar
2. Download this zip ROM file: RUU_Spark_Vodafone_FR_1.09.707.07_Radio_5.50.09.15_22.23.50.09U_Signed_by_ansar
Extract the downloaded zip ROM files with an unzip / 7zip utility in separate folders of your choice
C. Flashing Process
In order to successfully flash the provided ROMs you must follow these steps:
1. Flash the ROM of the above (B.1.) extracted zip ROM file
2. After flashing Tropy 7 will automatically enter again in bootloader mode
3. In the screen of your computer the ROMUpdateUtility will report an ERROR[270]
4. Ignore it and exit from ROMUpdateUtility
5. Now flash the ROM of the above (B.2.) extracted zip ROM file
6. After flashing your Tropy 7 will boot normally
7. Exit from ROMUpdateUtility and proceed with your brand new ROM
If you do not want them you can delete all operator apps, in order to have more free RAM
Beware, in WP7 deleting an application means it is deleted from ROM
D. ROM Flashing Instructions
In order to flash a ROM follow these steps:
1. Press and hold power-on/off button to power-off the phone
2. Press and hold volume-down button and then press power-on/off button to enter bootloader mode
3. When your phone enters the tricolor screen bootloader mode, release volume-down button
4. Connect your phone to your windows 7/vista/xp pc/laptop with a usb cable
5. Verify that your phone will be identified and relevant drivers will be installed by windows os of your pc/laptop
6. After completion of (D.5.) above, check the usb message connection on your phone screen
7. To flash the ROM go to your pc/laptop folder where the downloaded zip ROM file is extracted
8. Double click on the ROMUpdateUtility.exe file and strictly follow the instructions on your pc/laptop screen
Till next version enjoy!!!
Regards, ansar
ansar you are great
but i desperatly searching for a rom suitable fro my trophy SFR using mango (officla update through zune)
searching for mango v2 ROM (with tethering support)
details
PC40100 SS-DC (4K)
SPL-4.6.22.50.0(129185) MNG
MicroP (LED) 0x09
TOUCH A1 (V10,20)
OS version : 7.10.77.20.68
FW version : 2250.21.40600.163
Hardware revision number: 0003
Radio soft Version : 5.69.09.05a_22.50.50.21U
Radio hard version: A.102.0.D4
bootloader : 4.6.2250.0 (129185)
chip soc ver : 2.2.5.0
will be a great pleasure if you reload file anywhere than rapishare .. i.e 4shared or hotfile .. i need it