Database Info

Wont Boot

I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks

Drunknasty said:
I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Click to expand...
Click to collapse
if your device is G3, unlocking is required to flash any rom, before upgrade your device, it is recommended to flash an official WM5.0 rom (in your case T-Mobile rom) with IPL and SPL 2.xx then flash again.
in general there are many probabilities for your issue.
((Where is TNT1.1?? did you mean 1.0?? ))

My Bad meant 1.0
So to get it straight.... I will need to unlock my phone each time?
Oh and to correct myself again, when flashing with the T-mobile ROM it says UPGRADE ONLY. And the read me file says its the wrong RUU. But it is the same file from Tmobile I used when I first got the phone. But I will try again.
Are there any other suggestions?

You need to read the "how to flash" sticky.

I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.

Try another ROM.

Sounds like you need the "Wizard Love" rom. I dont have the link handy but I am sure someone else does.
Drunknasty said:
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Click to expand...
Click to collapse

Already got it. Thanks I am trying to load it now. But the only thing is that the last time it failed and I can understand what the error says. I know the number is 300 but can read the language.
But I will let you guys know when this load completes.
Thanks again for all the assistance.

No worky worky. The load completed and then boots the splash screen shows and then stays there.
Any ideas?

Try to remove the battery and let it out for at least half an hour. Then put it back in and see what it does then.

I thought the same thing too. So when it got done last night, out of frustration, I removed the battery and left it there to wait on when I get off work today. I will report back on what happens.
Again I would like to thank you guys for helping me. I really do appreciate it!

STEP 1 install the original manufacturer ROM
T-mobile UK
http://www.tm-phonedownloads.com/download_manager_mda_vario.html
T-mobile US
http://www.t-mobile.com/wmupgrade/
Search for the original rom for any other
instructions on how to use the original rom can be found here
http://support.t-mobile.com/knowbase/root/public/tm23294.htm?&A2L.SERVICE=AboutUpgrading
Put it in the bootloader mode.. ( three color screens )
hope this helps..
cheers
Praneet

Ok I did that and it gave me ERROR 296: UPGRADE ONLY
Then it tells me that the NBF file cannot be used for my PDA Phone. Please get newer NBF file.
Is there any way I can get the Tmobile splash and IPL\SPL number back to original, it doesnt need to boot all the way into WCE but atleast show the same numbers and splash during boot up?
Or any other way to get this thing to work?
Thanks guys
BTW it is a HTC Wizard from T-mobile.

If you are getting an error 300 you need a newer rom update utility, and regardless if your phone is a G3 or G4 it needs to be unlocked before you flash any rom.. LOAD a OFFICIAL cingular ROM onto your device before going any further, then unlock your phone either via www.imei-check.com or through some of the tools offered here...

Which one should I down load from Cingular? Even though I have a Tmobile phone?

what ipl and spl are you using and what radio are you using. Just post all the numbers from the bootloader

As soon as I get home, I will post them.
Thanks

Ipl 1.01
Spl 3.08
Thanks

Drunknasty said:
Ipl 1.01
Spl 3.08
Thanks
Click to expand...
Click to collapse
uh oh. someone tell me if I'm wrong, but I think this is bad. it's the result of flashing a g4 with g3 or the other way around... keep searching, and good luck.

flash the original t-mobile rom. your phone doesn't appear to be unlocked. good luck

Flashing Radio ROM

I want to flash my current radio rom (1.27.12.11) to 1.27.12.17. but if i open the EXE of the file i get the flash window. and if i click update. it shows me that my current image is version 1.56.404.6 and if i want to update it to 1.00.000.0 ... so whats up? is that normal?
and is this safe to do?
i have an unbranded HTC TyTN 2

Hi
That's normal. The version number relates to the whole ROM, but as you are only flashing the radio that question and version comparison is meaningless.
Just flash and you will see the radio rom version change to the new one and everything else remains the same.
Regards
Phil

its stuck at 0%... my AS connection dissapeared.. what now?
i managed to reboot it correctly, but my AS disconnects at the colour screen... why is that?

On this topic, I want to flash this new radio also, but I don't trust Vista, my Sync connection is always doing crazy things, its my vista that toast.
So can I Flash a Radio just using the SDcard method?
And how?
Thanks
Oh, btw, HI all, my First post, and 1 month with my Kaiser!
And a noob question, whats the difference from a TouchFlo rom to a non-Touchflo?...

Hi
i managed to reboot it correctly, but my AS disconnects at the colour screen... why is that
Click to expand...
Click to collapse
ActiveSync will disconnect at the coloured screen as it isn't ActiveSync in use at that point.
You also likely need HardSPL installed, if you haven't already please see the top threads in this forum for info as to how it all works.
Regards
Phil

Well im trying to install HardSPL. but when it comes to the tricoulour screen i have to unplug and plugin back my USB. AS disconnects as it should. and RUU starts. now it says make connection trough AS.... how? i cant get it to connect anymore and i need to reset my device in order to be connected again..
*edit* nevermind it worked. just ignore and go to update and click update

I had the exact same problem with Windows Vista. Tri-colour screen and Hardspl wouldn't continue.
Everything worked until the Unplug-replug part, and thats where is all stopped.
Had to soft reset device to get it back.
Still haven't figured it out.
Question to Seniors, if my Kaiser is "Free" or "Open", do I need hardSPL?
Or is HardSPL for getting around unsigned roms?
EDIT:
Ok did some reading, and understand HardSPL a bit better now...
One problem was the USB with thought a HUB, and not directly connected. Second problem was Vista not finding some driver, needed a reboot, Strang, ... anyway.
ITs on!!!
I think I got it Flashed on my Kaiser, but how do I KNOW, is there a way to check?
Edit: Figured this out too, My TriColour is now different, the USB was up top, its not lower and it says something about SPL by pof..
Hope you have more luck Imperium, I now have Radio .17 on my Kaiser.

stock on 0% flasahing rom

hello everybody
i started to flash a new rom
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06[No_CubeV2]
and i think i followd all the instractions but after starting the flashing it stock on 17% after removing the battery as the program said it wont go over 0%
firs i installed kaiser-HardSPLv1 and after that i started to flash the rom and its not working.
pls tell me what to do to save my nice phone
dannt

speebman said:
hello everybody
i started to flash a new rom
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06[No_CubeV2]
and i think i followd all the instractions but after starting the flashing it stock on 17% after removing the battery as the program said it wont go over 0%
firs i installed kaiser-HardSPLv1 and after that i started to flash the rom and its not working.
pls tell me what to do to save my nice phone
dannt
Click to expand...
Click to collapse
"think" you followed all the directions?

sorry for my bad english or leak of knolge in this part of the world i just read so much regarding this subject ant the more i read the more i got confused
so i just sow the first logical faq and followd him, plz i need my phone all my life is in their, help me.
danny

speebman said:
hello everybody
i started to flash a new rom
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06[No_CubeV2]
and i think i followd all the instractions but after starting the flashing it stock on 17% after removing the battery as the program said it wont go over 0%
firs i installed kaiser-HardSPLv1 and after that i started to flash the rom and its not working.
pls tell me what to do to save my nice phone
dannt
Click to expand...
Click to collapse
Things that will help others help you:
1. where are you located?
2. who is your provider
3. what ROM WERE you on?
4. ok - you had a phone that was working - and you did:
a. what did you do first?
b. second?
c. etc.
Your message KINDA indicates that you flashed a ROM and had issues - so you THEN flash HARDSPL? was that successful?
Bill

im from israel but my phone is from uk i think, my original rom was the HTC 6.1
i just run the kaiser-HardSPLv1 program and then i started flashing the rom duty 6.1 rom and it stoped at 17% like the program said i removed the batery and started the flashing prosse again but now it doesny even go above 0%, now im stock in the tri color screan
its writen
kais130
spl-3.28.0000
cpld-8
and usb in the littel whait screan

speebman said:
im from israel but my phone is from uk i think, my original rom was the HTC 6.1
i just run the kaiser-HardSPLv1 program and then i started flashing the rom duty 6.1 rom and it stoped at 17% like the program said i removed the batery and started the flashing prosse again but now it doesny even go above 0%, now im stock in the tri color screan
its writen
kais130
spl-3.28.0000
cpld-8
and usb in the littel whait screan
Click to expand...
Click to collapse
you don't have hardSPL installed..! surprise, surprise

u don't have hardspl flashed from bootloader info u provided. flash hardspl be4 flashing any roms.
please search and read; this has been answered many times.
p.s. use the new hardspl by jocky which is a sticky in this forum.

speebman said:
im from israel but my phone is from uk i think, my original rom was the HTC 6.1
i just run the kaiser-HardSPLv1 program and then i started flashing the rom duty 6.1 rom and it stoped at 17% like the program said i removed the batery and started the flashing prosse again but now it doesny even go above 0%, now im stock in the tri color screan
its writen
kais130
spl-3.28.0000
cpld-8
and usb in the littel whait screan
Click to expand...
Click to collapse
OK - I do not think that you got the HARDSPL installed on your phone correctly - BECAUSE - I believe that it would say OLIPOF or JOCKY on it and it does not.
I have not seen the new HARDSPL 328 and 329 but it LOOKS like to me that you did not successfully get the HARDSPL on your phone.
Personally - I would scan the message boards for GSLEON3 (user name) and send him a private message - there are many others that can help you and he or others MAY come trolling by and take pity on you - but at the moment he is the one that helps people in your situation the most from what I have seen.
I would NOT continue to work on it myself as you can definitely mess your phone up permanently. Does your phone still go into boot loader mode? If so - can you flash the required HARDSPL onto your phone?
Find a message that GSLEON3 has left and then lik on his name and send him a private message - he is very nice - BUT - he is VERY busy - continue to be nice and he will most likely get you back and running.
Bill

first of all thank u for the help
but, wich one i need? 28 or 29?
and how do i do this spl if i cant copy them to my device.
danny

speebman said:
first of all thank u for the help
but, wich one i need? 28 or 29?
and how do i do this spl if i cant copy them to my device.
danny
Click to expand...
Click to collapse
Danny -
Deep cleansing breaths here ok?
1. personally - I would PUT BACK what ever you had on your phone and get it running again - trying at this point to get ot to go to a different ROM is not a good idea right at this minute.
2. 28 and 29 from what I read makes no difference - users try each one to see which one works better on THEIR flashed ROM.
3. What I would do is look for the HARDSPL that goes with what you had loaded to begin with - or the actual SPL that came with your original ROM and put that one back.
I would be stuck here because I have to use JUMPSPL on my phone because I get the white screen - but I THINK that (don't quote me because I do not do it this way) if you don't get the white screen you can just flash the HARDSPL to your phone without JUMPSPL (having to be able to copy something to your phone.
HOWEVER - if you cannot or do not know how to continue from reading the WIKI - you MUST request help from a professional - I have already recommended one. (GSLEON3)
Bill

my active sink is not seeing the devais, maby MTTY? wil help

speebman said:
my active sink is not seeing the devais, maby MTTY? wil help
Click to expand...
Click to collapse
Based on your current track record, I wouldn't suggest you use MTTY as you have a VERY HIGH probability of bricking your phone (ie: it won't ever be usable again).

so im fu--.

Can you get the phone into the bootloader mode? Turn the phone off (pull the battery if you have to) then press and hold the camera button while you turn the phone on. You should get to a tri-color screen (this is the boot loader). Now plug in the USB cord and see if it switches from saying Serial to USB. If so, you can try flashing AN OFFICIAL ROM THAT WAS MEANT FOR YOUR PHONE (ie: Don't try to put an offical AT&T rom on an Orange). When you run the RUU program it will tell you that you need to have ActiveSync working, but don't worry about that. If your phone in bootloader shows USB, you can continue on.
BUT AGAIN... You need the Official rom that was meant for your device. Since you are not HardSPL'd you have to do it this way.
If you don't understand any of that, or have questions, don't just try it hoping you get it right...
As stated previously, it would be well worth you time to get someone like GSLEON to assist if you can.

mfrazzz said:
Can you get the phone into the bootloader mode? Turn the phone off (pull the battery if you have to) then press and hold the camera button while you turn the phone on. You should get to a tri-color screen (this is the boot loader). Now plug in the USB cord and see if it switches from saying Serial to USB. If so, you can try flashing AN OFFICIAL ROM THAT WAS MEANT FOR YOUR PHONE (ie: Don't try to put an offical AT&T rom on an Orange). When you run the RUU program it will tell you that you need to have ActiveSync working, but don't worry about that. If your phone in bootloader shows USB, you can continue on.
BUT AGAIN... You need the Official rom that was meant for your device. Since you are not HardSPL'd you have to do it this way.
If you don't understand any of that, or have questions, don't just try it hoping you get it right...
As stated previously, it would be well worth you time to get someone like GSLEON to assist if you can.
Click to expand...
Click to collapse
thank you!!!!!!1
i have flashed to my priviuas rom the original 6.1 htc rom and now its ok!!!
tnk

speebman said:
thank you!!!!!!1
i have flashed to my priviuas rom the original 6.1 htc rom and now its ok!!!
tnk
Click to expand...
Click to collapse
Cool. Glad that worked for you.... NOW, your next task is to read and understand ALL the steps before you try flashing a custom rom. HardSPL that sucker (but understand and follow EVERY step before you try that) and then you should be good to go...

my only problem is that their are so many strings of information and so many threads even wiki is confusing.
i will try to do this after i will make some order it all of this.
tnx again 4 the help
danny

speebman said:
my only problem is that their are so many strings of information and so many threads even wiki is confusing.
i will try to do this after i will make some order it all of this.
tnx again 4 the help
danny
Click to expand...
Click to collapse
Yes it is, but if you read this sticky at the top, it should help (start with noob guide which is the first link I think):
http://forum.xda-developers.com/showthread.php?t=369282

speebman said:
my only problem is that their are so many strings of information and so many threads even wiki is confusing.
i will try to do this after i will make some order it all of this.
tnx again 4 the help
danny
Click to expand...
Click to collapse
Not to be mean but if you have red Wiki and looked at threads here and they "don't make sense to you". You really have no business flashing a rom. If you don't understand what you are doing sooner or later you will brick your phone from your lack of knowledge and it will be no ones fault but your own.
I am really surprised people were willing to repeat what has been typed out hundreds and hundreds of times on these forums.
Welcome to XDA

weird.... now stuck in bootloader

hey all, i turn my tilt off every night for a few hours and this morning on my way to work, all i got was the bootloader screen, thought something was wrong turned it off removed battery and after waiting 5 or 10 mins put the battery back in and everything worked fine. later on during the day i shut off my phone again and its back in bootloader again upon powering up this time i cannot exit. dont know what to do.

Take out your MicroSD card, then hard reset.

will not hard reset, tried about 20+ times

Bad flash.. For solving you need to search the forum, then reflash whit a good rom.

is it possiple that my version if hard spl is corrupted?

We wouldnt know, you never mention it. What does the bootloader say? What are the text on it?

flashed with a shipped rom still showing bootloader

kais1*o
spl-3.29.hard
cpld-8

http://forum.xda-developers.com/showthread.php?t=394839&page=31

Nightlife said:
Ok, keeping in mind my rookie status, this is what my phone says on the boot screen (after installing [June 02] L26_Kaiser_Diamond_V5 (Hybrid 3.29.707); could someone humor me and tell me if this is correct? Did I install the "screen freeze" fix correctly after flashing the above rom?
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
Thank you in advance...
Click to expand...
Click to collapse
kyphur said:
No, the SPL Line should read "SPL-3.28.Hard" or "SPL-3.29.Hard".
Go back to the new HardSPL thread and read the FAQ carefully, everything has been condensed and all of the info you need is there.
Also, your question really belonged there not here..
Click to expand...
Click to collapse
---------------------------

im sorry but im confused, what am i suposed to see here?

ive tried flashing a different version of hard spl ...no luck......different roms no luck, no change

What exactly did you do from here:
http://forum.xda-developers.com/showthread.php?t=396922
And what exactly happend?

all i can do is run the hard spl files and it wont change anything, windows mobile wont start so i cant jump spl or acces the phone, my sim and my micro sd are not in the phone

RUU error (262) update error

Hello guys...
Iam not new, and i have already flashed my first(it was wasted not by my fault)KAISER, it was one year ago and i did it with HARDSLPv1, and lately added some new roms cooked by sakajati(respect)...
Yesterday i bought new one(but one year old) so i tried to flash him as well, i have used HARDSPL 1.93, and then i tried to put Sakajati"s 4th feb ROM, but i come across one big trouble, everytime i try to put it on i encounter the same RUU error:
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue. Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
what to do...????
i am very afraid that i destroyed my Kaiser...???
what it means that Wince is destroyed...
Please help me, i am desperate...

Iam not new,
Click to expand...
Click to collapse
But the solution could be found here (search)
If you see the tri color screen everythng is ok, just win mobile is destroyed. Try to flash a rom from your sd card

Thank you very much...
I hope it will work, i really did search for about an hour and tried to put rom on sevral times, but i didnt find nothing 100% secure, i dont want to indanger the unit any more that i did...
thanks again, i will try it tommorow morning at my job, thats where my SD card is...
)))

greganovak said:
Thank you very much...
I hope it will work, i really did search for about an hour and tried to put rom on sevral times, but i didnt find nothing 100% secure, i dont want to indanger the unit any more that i did...
thanks again, i will try it tommorow morning at my job, thats where my SD card is...
)))
Click to expand...
Click to collapse
Part of the problem is that 1.93 is a jump spl and should be used to upgrade to Hard spl 3.29 or 3.56, not as an spl on its own. You need to run jump spl 1.93 from your device and make sure you are connected to your computer, when you see the bootloader you need to unplug your USB, count to 10 and plug your USB back in then flash a hard spl to your phone! Again 1.93 is not a Hard Spl by itself, it is only a middle man to flash a Hard Spl.

I think the best would be to flash a stock rom at first, cause therefore you don't need an other bootloader. Then flash Hardspl (3.29 if you have a kaiser or 3.56 if you have a tilt) and then flash any rom you want

i obviusly have a lot to learn, mate how do I asses if I have TILT or KAISER, what is the main difference...
[email protected]: i have already DL the stock rom before i posted the tread, i hoped on that resolution if there were no answer...
in about 10 hours from now i will get my hands on my tilt/kaiser and hope to arranged the mess i done; I drop by in any case at that time and notify you about condition and my successes...
p.s.:sorry for my poor english...

greganovak said:
i obviusly have a lot to learn, mate how do I asses if I have TILT or KAISER, what is the main difference...
[email protected]: i have already DL the stock rom before i posted the tread, i hoped on that resolution if there were no answer...
in about 10 hours from now i will get my hands on my tilt/kaiser and hope to arranged the mess i done; I drop by in any case at that time and notify you about condition and my successes...
p.s.:sorry for my poor english...
Click to expand...
Click to collapse
It realy doesnt make that much of a difference, I have a tilt and I use 3.29 and I would recomend it to anyone over 3.56 so flash either one, they will both work! And your english is great so no need to say sorry!

greganovak said:
i obviusly have a lot to learn, mate how do I asses if I have TILT or KAISER, what is the main difference...
[email protected]: i have already DL the stock rom before i posted the tread, i hoped on that resolution if there were no answer...
in about 10 hours from now i will get my hands on my tilt/kaiser and hope to arranged the mess i done; I drop by in any case at that time and notify you about condition and my successes...
p.s.:sorry for my poor english...
Click to expand...
Click to collapse
A Tilt is a At$T branded Kaiser, a TyNT II is a HTC branded Kaiser. Tilt has a different keyboard and OEM rom., only differences. People say use 3.56 if you have a Tilt because that is an AT$T Spl, but I use 3.29 on My Tilt and it works great so it doesn't really matter.

hey...
nothing seems to work...
I have tried to put default rom dl from here: http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs but the problem is that it is not bootable from SD, that has to be because the USB conection isnt on (i selected the 3.34.721.2) so i given up that way
Then i flashed the HARD spl 3.29(have kaiser) via SD steb by step first with this instruction: http://forum.xda-developers.com/showthread.php?t=433835; and it dint go through
so i tried with this instruction: http://forum.xda-developers.com/showthread.php?t=420683
it didnt work either, they are the same I know(noticed later);
So problem is that i stuck at WHITE screen that says "LOADING..."
nothig else...???

finally i manage to load/boot the htc rom from xda-wiki site, but i have to chose another one

I have tried to put default rom dl from here: http://wiki.xda-developers.com/index...me=Kaiser_ROMs but the problem is that it is not bootable from SD, that has to be because the USB conection isnt on (i selected the 3.34.721.2) so i given up that way
Click to expand...
Click to collapse
Hey man, nice to see that your device rewakes, you can flash every rom from sd card, simply rename the nbh file to kaisimg.nbh than restart into bootloader and it will automatically take the one from the card

Unfortanly, althought i would like you to be right, you are not. When i tried to do it via SD, i stuck at white screen saying LOADING...(blue) and nothih further... and i tried also the Cmonex_s Hard SPL3.29_SD which also stucks at same screen
So now (after updatig with default rom) that i have basicly normal working device i startet from the top. Using @mskip"[email protected] tutorial called: Flasing your first rom (for noobs); it all goes well, till i start to update RUU(sakajati 4 feb) if it matters, and i tried both (spls 1.56 and 1.93), it stops updatig at 17% and notrhin else then works just puting back the HTC default rom from wikiXDA side(thank god for that)
i am thinking of MTTY, although i dont know what it does guys here almoste all say it fix bad rom flash, but i am not sure if thats my main problem, i rahter think it has something with spls...
if someone has some good advice i will be very grateful...

greganovak said:
Unfortanly, althought i would like you to be right, you are not. When i tried to do it via SD, i stuck at white screen saying LOADING...(blue) and nothih further... and i tried also the Cmonex_s Hard SPL3.29_SD which also stucks at same screen
So now (after updatig with default rom) that i have basicly normal working device i startet from the top. Using @mskip"[email protected] tutorial called: Flasing your first rom (for noobs); it all goes well, till i start to update RUU(sakajati 4 feb) if it matters, and i tried both (spls 1.56 and 1.93), it stops updatig at 17% and notrhin else then works just puting back the HTC default rom from wikiXDA side(thank god for that)
i am thinking of MTTY, although i dont know what it does guys here almoste all say it fix bad rom flash, but i am not sure if thats my main problem, i rahter think it has something with spls...
if someone has some good advice i will be very grateful...
Click to expand...
Click to collapse
Hi,
I couldn´t flash my Kaiser via SD at the first time and tried something that worked.
The SD´s are formatted in Fat16 usually, try to format to Fat32... It seems like a stupid thing, but worked for me.
Reagards and good luck.

SD must be formated FAT32, to work, also I sugest a smal card, 512 or something like that, SHDC usual doesn't work

I have 1GB SD and its not shdc, so thats ok.and i have done it right now, like you two guys said so i formated it with FAT32 but still no succes.
I guess that this tree lines in red/green/blue screen arent right:
KAIS130
SPL-3.02.0000
CPLD-8
i thing this SPL has to da something to do with all this mess a have done
I have flashed a couple of roms( i had three devices) and i flashed a few for my friends and all was OK till now, and i dont know what else to do...

greganovak said:
I have 1GB SD and its not shdc, so thats ok.and i have done it right now, like you two guys said so i formated it with FAT32 but still no succes.
I guess that this tree lines in red/green/blue screen arent right:
KAIS130
SPL-3.02.0000
CPLD-8
i thing this SPL has to da something to do with all this mess a have done
I have flashed a couple of roms( i had three devices) and i flashed a few for my friends and all was OK till now, and i dont know what else to do...
Click to expand...
Click to collapse
Yes, you still have a stock spl on there. It needs to be hard spl'd before you flash anymore. Check out the stickies at the top of the forum.

hi again...
Well, I respect the "rules" of forum, thats why i wouldnt ask for insructions that are already written(thanks for the authors) with that i mean stickys, because i read them, almost all...
But I still tried once again, and I came across the same thing, i stuck at 17% when loading RUU or if i choose the VIA SD i stuck at white screen with blue text saying (LOADING...)...
nothing else helps than loading the dafault ROM by HTC... as i already said once again...
if i manage to solve the problem i will be in touch; what do you thing about MTTY
Edit 1:
i have done everything as it says in the instruction, and just like some of you "replyed" me...
but i always stuck at 17%when loading RUU, when i flash it with SPL 1.56 or 1.93 i never get stuck at white screen it always apeare the mentioned SPLs nimbers and some other text in yellow but when i then load RUUs i stuck at excatly 17% nothing less nothing more
edit 2:
yupi....yupi
i made it...
http://forum.xda-developers.com/showthread.php?t=354061 here is my lifesavior...
those instruction were the one that helped my problem...
it is very nice to ba a part of this community....