Related
1st off I DID use the search button.... 2nd HELPPP ME!!!
Waaah :'( I have a most intriguing problem I was running pdaviet 4.0.0.6 Touch for almost 2 weeks now without a single glitch.. the phone fell on my carpet and went to bootloader screen and eversince then it has never recovered I tried a hard reset it didn't work when I was pressing the send button it did nothing I did some forum searches and tried putting back the nvid RUU and it said that the update was succesfull and the progress bar on the phone moved accordingly but it went back to the bootloader screen ... then I tried pdaviet temp rom that was in the package still no go I can tell it works somehow because the USB lights up in the bottom left when I plug the usb cable and the progress bar that moves, but I'm getting desperate IPL and SPL info is in my sig...
same same... but i dropped mine before flashing the new PDAVIET touch rom.. still went fine..
now, it still flashes... RUU says its successful.. but PDA just reboots back to bootloader..
i can charge my phone fine in bootloader.. i can see the USB come on when i connect it to my computer.. other than that, can't do anything...
i've tried everything the past 2 days.. looks like i'll have to send it back to dopod.. will let u guys know what happens... probably something got damaged..
struck at bootloader
I tried WM6 (4.0.0.6 touch) from WM5 AKU 2.2 but it failed in between with some write message,which was bit strange as I didn't touch any key on laptop during that time and no program was being run at that time. (I am using VISTA Home premium). I got my phone into bootloader but it does not connect to my laptop...so cant upgrade back to AKU 2.2. In Windows Mobile Device Center, I cant see my device connected. So is it particular to Vista or my phone got bricked?
I am yet to try on Windows XP, which I have to arrange.
Please advise.
i had the sam problem.i installed this : try to install the 2.20 nvid rom
just go into bootloader mode-you dont need active sync connection and start the upgrade-search for 2.20 nvid rom download it and recover your device
charliess said:
i had the sam problem.i installed this : try to install the 2.20 nvid rom
just go into bootloader mode-you dont need active sync connection and start the upgrade-search for 2.20 nvid rom download it and recover your device
Click to expand...
Click to collapse
I tried the same but when I run ROMUpdateUtility_No_VenderID, I get a message 'Update Error, 260' which tells further that PDA is not connected to laptop., although it is very much connected. However LED on PDA does not blink as well.
When I plug in this phone to Wall adaptor, LED does show up.
'USB' appears at Bottom Left corner of PDA when connected to laptop and certainly its getting recognised by Vista as it starts installing Driver as soon as this is connected to laptop.
Please suggest.
I am stuck in the same situation, although I have a G3, running 2.20 on IPL & SPL
Working now
I tried on XP (I was trying on vista before)..I had to install Active Sync as it was not installed on that PC, then run RUU update for AKU 2.2 and update was successfull. Now will try Touch 4.0.0.6 again but this time on XP.
Hope this time I wont have any problems.
Possibly the fastest phone brick in history... I did everything wrong...
AT&T Tilt, Windows Vista host machine
I ran the SSPL, NOT the Hard-SPL...
16% thru it failed
Rebooted, tri color screen, but not the same extact screen I had seen after running the SSPL on my Tilt.
Hard Reset, said yes take me to factory settings, back to same tricolor screen
Plugged it into a XP box, drivers installed, plugged in USB (it shows USB connection on the screen) Activesync of course wont go green
Loaded both the Kraiser rom and the Cingular rom, both fail at 1% and reboot the device and same invalid device ID..
Any ideas, aside from I'm a r-tard?
I ran the Hard-SPL on my HTC and it worked as it should. I'd say give that a shot, THEN try flashing the ROM of your choice.
-Mc
Problem is, when I run hard spl it expects activesync to be running, but in bootloader mode AS doesnt connect so Hardspl wont load =/
- Disable activesync usb connections
- Connect to bootloader with mtty and type the following commands to know your CID and Model ID:
Code:
Cmd>task 32
Cmd>info 2
Cmd>getdevinfo
Paste the output here, and also tell me which SPL version you have on your device.
Also, does the tri-color shows "RUURUN" or similar in the screen?
You should flash a ROM matching your CID to fix it.
Cmd>task 32
No card inserted
Level = FF
Cmd>info 2
HTCSCWS__001Ùü¤HHTCE
Cmd>getdevinfo
GetDevInfo: Get CID OK
HTCSKAIS1*00CS_0HTCE
Cmd>
Device screen says
RUUNBH
KAIS1*0
SPL-1.56.0000
CPLD-8
Flash this ROM, should bring it back to life.
I'm leeching it now, 40% done, also FYI, I've posted on the Official ROM forum new links to most utilities and ROMs hosted on my servers off the rapidshare, to share free of charge.
Ahh, life saver =) Thanks, I'll be sure to add that rom to my list of full Kraiser roms on my web server, now to correctly flash it back with the HTC rom.
Thanks!
Same problem as TS. Bigger problem ... does anyone have the Dutch ROM?
Tnx!
I got the same problem as Palmore. After 16%, stuck, then bricked. I am downloading the ROM pointed by POF (thanks man!!) hopefully will unbrick it. Now, how do we get the HTC Kaiser ROM on this thing? Anyone?
It's on my phone. Tell me how do dump it and I ll send it to you.
Wouter
Lukstra said:
Same problem as TS. Bigger problem ... does anyone have the Dutch ROM?
Tnx!
Click to expand...
Click to collapse
ludovich said:
I got the same problem as Palmore. After 16%, stuck, then bricked. I am downloading the ROM pointed by POF (thanks man!!) hopefully will unbrick it. Now, how do we get the HTC Kaiser ROM on this thing? Anyone?
Click to expand...
Click to collapse
Run the Hard-SPL utility on your PC, and follow the instructions (sticky on this forum)
It will allow you to flash any ROM after that, I've flashed the AT&T Rom, the HTC rom and back and forth, pulling cabs out of the AT&T rom for the items I like (IM utility etc)
Palmore said:
Possibly the fastest phone brick in history... I did everything wrong...
AT&T Tilt, Windows Vista host machine
I ran the SSPL, NOT the Hard-SPL...
16% thru it failed
Rebooted, tri color screen, but not the same extact screen I had seen after running the SSPL on my Tilt.
Hard Reset, said yes take me to factory settings, back to same tricolor screen
Plugged it into a XP box, drivers installed, plugged in USB (it shows USB connection on the screen) Activesync of course wont go green
Loaded both the Kraiser rom and the Cingular rom, both fail at 1% and reboot the device and same invalid device ID..
Any ideas, aside from I'm a r-tard?
Click to expand...
Click to collapse
If you are a r-tard, it must be catching - same situation here at 16% and 1% now......
andydempsey said:
If you are a r-tard, it must be catching - same situation here at 16% and 1% now......
Click to expand...
Click to collapse
LIFE SAFVER
nispen said:
It's on my phone. Tell me how do dump it and I ll send it to you.
Wouter
Click to expand...
Click to collapse
Hi Wouter,
I bought a new Kaiser today (yes now I have two of them ).
I will see if I can dump the Dutch ROM myself and see what happens next.
Thanks for your help anywhy!
- Lucas
Bricked
Ok, so here is my situation. I have a Tilt and Vista.
I ran HardSPL and I am at the tri-color screen. I have:
KAIS1*0
SPL-1.JumpSPL
CPLD-8
USB (in the middle of the screen)
I tried disconnecting and reconnecting it several times. I cant get HardSPL to run again (it hangs at the first section looking for ActiveSync) I tried restarting Vista several times. I can NOT turn off my device, as holding down the power button does not appear to work.
I have tried just running a couple of .exe roms (AKU 0.7.0 ROMS) and I get the connection error [264]. I cant re-establish my ActiveSync connection. In device Manager I have Microsoft USB Sync for the mobile device, but I cant get ActiveSync (Mobility Center) to see it.
I have tried opening MTTY to run "boot" but it says USB Port Can NOT be opened.
I just need some direction here, as it seems like everything hinges on my ActiveSync connection. I have been up and down the Wikis for Hermes and all the similar ones, and I think I am SOL.
I WILL GLADLY DONATE if thats what it takes for someone to help me. Thanks guys, I cant wait for my HTC Rom to work.
Vista Problem.
First off, i had the same problem as you so i just found an XP box to use.
Second, even with XP i still managed to **** up because i did not read the directions all the way through. This device is totally different so make sure you read all the directions.
If you have no access to an XP machine then u can just "obtain" a copy of XP and dual boot just for flashing your device.
If you have no idea what I am saying then read some more. the hermes forums have some great information when it comes to flashing via Vista.
For all you guys that just saved between $300.00-$500.00. How about sending POF like %5 or %10 of what he just saved you...
I'm just sayin'
Later, Lew
Have you installed the XP activesync drivers under Vista? The Hermes Wiki mentions somewhere how to do that.
Jabbs19 said:
Ok, so here is my situation. I have a Tilt and Vista.
I ran HardSPL and I am at the tri-color screen. I have:
KAIS1*0
SPL-1.JumpSPL
CPLD-8
USB (in the middle of the screen)
I tried disconnecting and reconnecting it several times. I cant get HardSPL to run again (it hangs at the first section looking for ActiveSync) I tried restarting Vista several times. I can NOT turn off my device, as holding down the power button does not appear to work.
I have tried just running a couple of .exe roms (AKU 0.7.0 ROMS) and I get the connection error [264]. I cant re-establish my ActiveSync connection. In device Manager I have Microsoft USB Sync for the mobile device, but I cant get ActiveSync (Mobility Center) to see it.
I have tried opening MTTY to run "boot" but it says USB Port Can NOT be opened.
I just need some direction here, as it seems like everything hinges on my ActiveSync connection. I have been up and down the Wikis for Hermes and all the similar ones, and I think I am SOL.
I WILL GLADLY DONATE if thats what it takes for someone to help me. Thanks guys, I cant wait for my HTC Rom to work.
Click to expand...
Click to collapse
Best Forum Ever
I
I got it working. I had to pull the battery out of the phone to get it out of bootloadr, it was just plain stuck. Then, in Vista, I needed to F8, disable driver enforcement, I replaced the wceusbh.inf in device manager, and relaunched HardSPL and there she was! Now for the BigStorage.
Thanks to all that helped, I will be donating pof for sure
Sorry for my english, i'm french...
It is possible use hardspl with vista ?
And save my actualy ROM (SFR: vodafone) before flash ?
My phone is a HTC V1615 (P4550)
Thanks
yes you can use HardSPL with Vista. During the process, the instructions say to unplug and then reconnect the USB. When you do this, just make sure the drivers are fully installed after you reconnect, before you continue forward.
As far as saving your ROM, you may have to go to your carrier's webiste, and download a copy of the original ROM for a backup. It might be somewhere in this forum, as well, but you would have to search for it.
Hope that helps....
Thanks for your explications
For the original ROM i search it...but without result.
Thanks again
Vista
Go to this page for a tutorial and the files you will need for flashing with Vista
http://www.mrvanx.org/cms/index.php?...23&Itemi d=27
Hrm link changed finding it again.
Ok here is working link.
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
I'm not having a WSOD, but at this point, at least that would be something happening. I've gone through the Vista-to-XP driver switch and everything else I can get my hands on, but can't get anything to happen after I unplug the USB cable and plug it back in. I've restarted Vista several times, tried a few different versions of the ActiveSync drivers, but I can't get passed the tri-color/USB screen. If I had another box to use I would install XP, but I don't at the moment. Any of you Vista Ultimate guys that have pulled this off, what did you do?!?
I've flashed on Vista. You have to be aware of a few things:
a) When the Flash process starts, the Rom Updater does not recognize the phone as a Kaiser, but is talking to the unit as a piece of hardware using the USB interface. Therefore, the mrvanx procedure must be followed strictly, since these are the drivers that will be invoked during the initial phase.
Before you plug and unplug, check Device Manager->Mobile Device to see that the driver "Microsoft USB Interface" has loaded properly. (It may be called "HTC USB Interface" too).
b) If you are running Vista 64 bit, the drivers must be signed, as mentioned in the mrvanx tutorial. Alternatively, you can restart Vista without driver signature enforcement (F8 while booting up, select this option) before flashing.
Hi my Qtek 9000 doesn't work anymore after installation of Ranju_v77_WM61_19900_19900_1_0_2.
it never finished it.
but when i try to recovery on qtek or with the pc, with the Ranju installation program.
it also said don't look weird if you only got usb with the version number on your pda screen.
that window comes after if the installation failed, but when i try to back it up the program stops working.
so now i can't use my pda please help me.
Greetz, (n00b)
pommie said:
Hi my Qtek 9000 doesn't work anymore after installation of Ranju_v77_WM61_19900_19900_1_0_2.
it never finished it.
but when i try to recovery on qtek or with the pc, with the Ranju installation program.
it also said don't look weird if you only got usb with the version number on your pda screen.
that window comes after if the installation failed, but when i try to back it up the program stops working.
so now i can't use my pda please help me.
Greetz, (n00b)
Click to expand...
Click to collapse
Hi,
The answers you seek are in the WIKI.
Hold the backlight + power button whilst resetting the device. This will put you back into bootloader mode, you can then reflash the Rom.
I would also advise that you SuperCid your device before flashing any Roms, if you haven't done so already.
Again this is documented in the Wiki.
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
Cheers,
Beasty
my screen show me serial v1.01 and if i put the usb cable in it shows me usb v1.01
on my pc it installed as microsoft usb sync, but it won't connect on windows mobile device center.
so i can't use mtty even if i unselect usb in windows mobile device center i still can't select usb in mtty ive tried few times to delete and reinstall on my pc but still does not work.
pommie said:
my screen show me serial v1.01 and if i put the usb cable in it shows me usb v1.01
on my pc it installed as microsoft usb sync, but it won't connect on windows mobile device center.
so i can't use mtty even if i unselect usb in windows mobile device center i still can't select usb in mtty ive tried few times to delete and reinstall on my pc but still does not work.
Click to expand...
Click to collapse
The problem is Vista!
Search the forum and you will find a post with a fix (old drivers) for Vista, or just use a Windows XP or previoous MS OS to flash your device.
I would suggest XP if you plan to keep flashing in the near future
do i need to super cid my htc universal in order to upgrade to ranju v77. my universal is branded dopod 900 and can use with any simcard. thanks
lucky for me, i also got a pc with xp sp2 but my pda works with ranju v77 thnx man.
only from nokia phones i can't send file with bluetooth, phones like samsung works fine
dear all,
first at all: I´m completely new here, so hello.
I finished reading the Wiki twice, also the guide from 'mskip' (Flashing your First GSM Raphael Rom (For Noobs)). very good and sounds very easy.
now I downloaded this file: RaphaelHardSPL-Unsigned_190_1_3
when I´m trying to flash, it results in a "error 202: connection". could the windows mobile device manager be a reason, because here is just an explanation with activesync. as I use win7 64bit, activesync will not run.
I also checked lots of posts here, but did not get a right answer which could lead to a solution.
btw I have the "MDA Vario IV"-version.
greetings, tris
EDIT:
Update: Now I downloaded "TAEL ROM v6.28244 RC2".
Connected mobile to PC, waited until it is connected via 'windows mobile device manager'.
Proceeded with the update (my image is 1.69.111.6) until the screen turned black and a progress bar is shown (0%). now error 262 appeared. have to unplug USB cable, reinstall battery and restart. old system is still working. what am I doing wrong? btw, same error on my laptop with win7 32bit with fresh installed 'windows mobile device manager'.
EDIT2: okay, and same on my other laptop with winXP and activesync.
You need to flash hard spl before doing anything else. Try putting the phone into bootloader (hold volume down, then soft reset), then connect it to your PC once it's in the tricolor screen and run the hard spl exe.
After that, just flash roms off your sd card. Make sure it's FAT 32 format, rename the ruu_signed.nbh to RAPHIMG.nbh, put it on the sd card root, and then go into bootloader and follow the instructions.
volume down and reset done. phone switched to tricolor screen. then I started 'RaphaelHardSPL-Unsigned_190_1_3', phone switched to gey screen with progress bar. 30 seconds later after 0% progress: error 262 appeared
EDIT: also when trying to update via bootloader, my image (1.69.111.6) will be left blank, I can´t see the version number which is currently installed.
I just hope you have a GSM TP/RAPH...
RAPH300 -> "T-Mobile MDA Vario IV"
but why do you ask? do I have the wrong software?
Just hear of those bad incidents with CDMA phones and GSM ROMs is all...
What does it display on the bottom of the screen when you boot into the tricolor screen/bootloader before you connect it to your PC and then after?
first serial, later USB
oh my god! *facepalm* okay for all the noobs out there: look at your phone. if you use HardSPL for the first time, you have a short timeframe to confirm "unsigned access to bootloader" via touchscreen. if you don´t do so, you will result in connection error 202 / 262.
thank you all, it works