If the answer is one this site already I apologize to everyone but I have been searching for 3 days now and no joy.
I will try to keep is short and simple.
I have been flashing for the last year now and have never had trouble until now. Flashed Duttys ROM released on June 5th I believe. Went great but still had old HardSPL on my phone. Followed the steps to flash latest SPL 3.29 and it never took. As a matter of fact something happened to the USB and my pc was unable to recognize the device. So I was stuck for the moment and had to leave that way until I had more time.
Received a phone call and when I hung up it went to white screen with call graphics at the bottom, missed call, received call, etc. I soft reset the phone and then the Tri-Color screen came up and this is the info:
KAIS130 MFG
SPL-1.0.0lIPof
CPLD
I am assuming this is the first HardSPL that I loaded. So then I preceed to flash via SD and it says that the flash completed and was successful. However when I soft reset the phone goes back to the Tri-Color sceen and does not load the image I just flashed.
Anyone have any ideas how I can get this phone working again? I am open to any and all suggestions.
Thank you in advance
does the bootloader show ruunbh on top?
ok this should be an easy fix! the poster above asked the right question!
lets start from scratch now though ok,
-first download SSPL.KAIS and save it to your memory card.
- Download Which ever hardSPL you would like to use.
- run SSPL.KAIS from SD card and then flash New HardSPL, check to make sure it flashed right by going into bootloader should say what ever SPL you just flashed.
- If that flashed correctly then proceed to flashing the HTC WM6.1 shipped ROM, which can be found on the forum! Make sure its a NON-cooked rom...
- If that flashed correctly then pick which ever custom rom you would like and flash that, make sure that flashed correctly and if so your done
Austinsnyc,
Thanks for the speedy reply. Sorry just a few questions and one statement.
The phone is in the Tri-Color screen state constantly. The only way I can load the bootloader is if I rename a ROM to KAISIMG.nbh. Then is something akin to ROM, radio, etc and when that flashes they will have an OK next to them. Alright with that said a few questions.
Do I have to rename the SSPL.KAIS file, it does not run as is? When loaded on the the card, Tri-Color comes up and then for a brief second is says, Loading.....No Image File.
Do I load both files on the card at the same time and do I have to rename them? i.e. KAISIMG.nbh
Thank you for your help
thesire said:
does the bootloader show ruunbh on top?
Click to expand...
Click to collapse
No it doesn't. I will say KAISIMG.nbh, the ROM I renamed to load. Then is list all the features of that ROM, i.e. OS, SPL, radio. I flash it and it says success but still will not load.
Thank you
culleyps said:
No it doesn't. I will say KAISIMG.nbh, the ROM I renamed to load. Then is list all the features of that ROM, i.e. OS, SPL, radio. I flash it and it says success but still will not load.
Thank you
Click to expand...
Click to collapse
MTTY
cmd>set 16 0
cmd>boot
Can MTTY be run form the SD card?
I didn't clarify so well, I cannot use usb connectivity to the PC. Everyting needs to be done off the SD card.
Thank you
culleyps said:
Can MTTY be run form the SD card?
I didn't clarify so well, I cannot use usb connectivity to the PC. Everyting needs to be done off the SD card.
Thank you
Click to expand...
Click to collapse
okay read more about mtty for clarrification. as long as it says usb when u hook up to computer in bootloader u should be fine. but first read on mtty before running cmds.
thesire said:
okay read more about mtty for clarrification. as long as it says usb when u hook up to computer in bootloader u should be fine. but first read on mtty before running cmds.
Click to expand...
Click to collapse
thesire,
I will research the this more. It does say usb on the phone with plug in otherwise when unplugged it says serial. When plugged in I can't see usb in the drop down in MTTY. I will keep reading.
Btw, it now says RUUNBH in the top right hand corner.
Thanks
culleyps said:
thesire,
I will research the this more. It does say usb on the phone with plug in otherwise when unplugged it says serial. When plugged in I can't see usb in the drop down in MTTY. I will keep reading.
Btw, it now says RUUNBH in the top right hand corner.
Thanks
Click to expand...
Click to collapse
that means you have bad data blocks which can also be cleared using mtty.
I must be very thick, I can't get MTTY to connect. Every time I plug in the USB to my Vista OS pc is says it can't recongize the device and it has malfucntioned. I know the USB is working, it was up until I was having this problem at least.
So I start MTTY and look for USB in the drop down for Port but only COM 1 & 2 show up.
So any other suggestions you or anyone else may have is greatly appreciated.
Thanks for your patience
with Vista you need to use Mtty 5.13 which can be found in the FrankenKaiser radio from hell thread. There is also a guide on how to install the old XP drivers to WindowsMobileDeviceCenter that helps a bunch with USB issues. Also I think you miss understood me the tri-color screen is the Bootloader screen!!!
USERNAME said:
that means you have bad data blocks which can also be cleared using mtty.
Click to expand...
Click to collapse
I don't think it means bad blocks for sure.
Ok. I have read just about everything I can find on MTTY, old XP drivers (which I already have installed) and I still can not get anything to work. When I plug in the phone via usb, pc says it cannot recongize the device and it must have malfunctioned. I have tried MTTY 5.13 numerous times and still cannot get usb to show up and have been unseccessful with all my attempts to connect via a COM port.
Is there any place in NYC, Brooklyn or Queens that I can take this phone too and someone with more experience can fix this for a fee of course? I just and need to get my phone working again.
So I have another question since I have been unable to get anywhere with the dang thing.
I am unable to get my laptop/pc to recognize the phone, I can't even get drives to load. Been searching and reading and still looking for a solution to this issue. If you know where is answer is in this forum could you please point me in the right direction?
Aslo, if someone is willing to spend the time with me to solve this issue get the phone running again, I will be more the happy to donate generously.
I think this can be solve quickly if I could get the time with someone.
For the folks that have replied, I can't thank you enough it has been a great learning experience.
Thanks
Same problem here. Please help!
I am having exactly the same problem. PANIC!
I am a complete noob to all this, but managed to flash Duttys Rom.
(Ruu_Signed_Duttys_WM6.1_Official_5.2.19209_1_58_16_27 [FIX])
I was incredibly pleased with the results.
The phone ran better than ever till this morning. The sound stopped working, I soft reset and now I cant get past the tri-coloured (boot loader ?) screen.
KAIS130
SPL-3.29.Hard
CPLD-8
SERIAL
I cant hard reset, it just goes back to the tri-colour screen.
Help!
If I am not being clear or more info is needed please let me know.
5manarmy said:
I am having exactly the same problem. PANIC!
I am a complete noob to all this, but managed to flash Duttys Rom.
(Ruu_Signed_Duttys_WM6.1_Official_5.2.19209_1_58_16_27 [FIX])
I was incredibly pleased with the results.
The phone ran better than ever till this morning. The sound stopped working, I soft reset and now I cant get past the tri-coloured (boot loader ?) screen.
KAIS130
SPL-3.29.Hard
CPLD-8
SERIAL
I cant hard reset, it just goes back to the tri-colour screen.
Help!
If I am not being clear or more info is needed please let me know.
Click to expand...
Click to collapse
Does it say RUUNBH in the top right corner?
Hi.
All I can see on the screen is as follows.
------------------------------------
KAIS130SPL-3.29.Hard
CPLD-8
Serial
------------------------------------
I have absolutely no idea where to go from here.
Cold sweat....
5manarmy said:
Hi.
All I can see on the screen is as follows.
------------------------------------
KAIS130SPL-3.29.Hard
CPLD-8
Serial
------------------------------------
I have absolutely no idea where to go from here.
Cold sweat....
Click to expand...
Click to collapse
The best thing for you to do is contact GSLEON3 to see if he can help you out.
Thanks for your response.
I somehow seem to have gotten somewhere.
I just repeatedly kept trying to hard re-set, taking the battery out, connecting USB.... and then it hard-reset.
They say the definition of insanity is doing the same thing and expecting different results.
I wonder if you can recommend a stable ROM? I love the speed and battery life of the one I installed but dont like the idea of being between meetings and having a phone in limbo.
Thanks again.
Related
I want to start out by saying I'm really sorry if I'm asking something stupid but I am a complete newbie and do intend to learn as much of this on my own as I can....
I took my brand new AT&T Tilt and I connected it to my Vista Laptop when it was charged fully and used the built-in Windows Mobile Device Center to do a quick connect (like a guest connect where files can be transferred but stuff isn't synched) and ran kaiser_HardSPL which gave me a white screen rather than the expected tri-color screen.
I found the solution for the white screen and did a reset by pushing the stylus into the small hole space on the bottom of the Tilt and then connected it again to my laptop and copied over JumpSPL1.56-KAIS to the phone. I then ran that app from the phone and the tri-color screen showed up. When 'USB' showed up on the screen I disconnected the USB cable for about 10 seconds and plugged it back in. The text 'USB' stayed on the screen and nothing happened after that. I then used the stylus again to reset the PDA again and I am now at my current step.
Am I ready to put a ROM on now? I'm so new to this and I definitely want to learn just not sure what's next....is my CID unlocked? Did everything go correctly or did I miss out on some important step?
What should I do next if I want to put a new ROM on? Whatever help anyone can give me would be very much appreciated.
Looking forward to becoming an active and contributing member to this great community!
Gas Addict said:
I want to start out by saying I'm really sorry if I'm asking something stupid but I am a complete newbie and do intend to learn as much of this on my own as I can....
I took my brand new AT&T Tilt and I connected it to my Vista Laptop when it was charged fully and used the built-in Windows Mobile Device Center to do a quick connect (like a guest connect where files can be transferred but stuff isn't synched) and ran kaiser_HardSPL which gave me a white screen rather than the expected tri-color screen.
I found the solution for the white screen and did a reset by pushing the stylus into the small hole space on the bottom of the Tilt and then connected it again to my laptop and copied over JumpSPL1.56-KAIS to the phone. I then ran that app from the phone and the tri-color screen showed up. When 'USB' showed up on the screen I disconnected the USB cable for about 10 seconds and plugged it back in. The text 'USB' stayed on the screen and nothing happened after that. I then used the stylus again to reset the PDA again and I am now at my current step.
Am I ready to put a ROM on now? I'm so new to this and I definitely want to learn just not sure what's next....is my CID unlocked? Did everything go correctly or did I miss out on some important step?
What should I do next if I want to put a new ROM on? Whatever help anyone can give me would be very much appreciated.
Looking forward to becoming an active and contributing member to this great community!
Click to expand...
Click to collapse
Quick question, and I'm not trying to be funny or anything, but did u read?
Thanks for the quick reply -- I did read the different threads that I thought would be dealing with this but was unsure of what to do after I did the white screen fix. The white screen fix said there was a way to test if it worked by checking a splash screen but when I ran that it said make sure you've already done HardSPL first otherwise it can brick your phone so I wasn't sure if I did actually do that step properly or not (of installing HardSPL).
I'd appreciate any help you could give me. Thank you again for taking the time to read my post!
Bronx31 said:
Quick question, and I'm not trying to be funny or anything, but did u read?
Click to expand...
Click to collapse
I can answer that!
I apologize for missing something obvious -- could anyone please point me to which thread I should look at?
Thank you.
No your device is still not ready.
http://forum.xda-developers.com/showthread.php?t=354061
You're on the right track. From what I gather you can indeed flash something at that stage on SSPL or continue on to flash HardSPL (which is what I believe you intended to do!). Get back to the stage you were at and, from the thread in which you found JumpSPL, flash HardSPL onto your phone. After that point you are totally ready to become a slave to dutty's roms...
Look here and ye shall find: HardSPL will not install - WHITE SCREEN: SOLVED
Well, first correctly install HardSPL, then go on flashing a ROM. You may find my FAQ usable. See my signature.
Nono... one more step to go.
After disconnect and connect usb flash hardspl then softreset.
bmueller77 said:
Well, if you correctly installed HardSPL which sounds like this, go on flashing a ROM. You may find my FAQ usable. See my signature.
Click to expand...
Click to collapse
Laurentius26 said:
Nono... one more step to go.
After disconnect and connect usb flash hardspl then softreset.
Click to expand...
Click to collapse
Already corrected it. But you were faster ^^
Thank you to all of you -- you're all being very helpful!
I ran the flash-hardSPL (ran the file in that folder called KaiserCustomRUU) and it gets all the way to where it is updating the rom image to the kaiser-hardSPL version and it shows 0% on my phone and 0% on the PC and after about a minute or so it says ERROR [262] : UPDATE ERROR ... it instructs me to remove my battery for 3 seconds, put it back in and try again.
I've done this twice now and keep getting the same error -- any ideas on what I'm doing wrong?
Thank you once again.
The only thing I can think about is that your phone is simlocked.
Do you have the usb cable connected straight to the pc or do you use a usbhub?
Gas Addict said:
Thank you to all of you -- you're all being very helpful!
I ran the flash-hardSPL (ran the file in that folder called KaiserCustomRUU) and it gets all the way to where it is updating the rom image to the kaiser-hardSPL version and it shows 0% on my phone and 0% on the PC and after about a minute or so it says ERROR [262] : UPDATE ERROR ... it instructs me to remove my battery for 3 seconds, put it back in and try again.
I've done this twice now and keep getting the same error -- any ideas on what I'm doing wrong?
Thank you once again.
Click to expand...
Click to collapse
Oh yes, that's true. I didn't realize I had to unlock my phone before I could start this process...I guess I confused it with CID unlocking or something.
I must have missed the part in the newbie FAQ about phones needing to be sim unlocked for all this stuff to work.
I guess I will have to get it unlocked first! Very much appreciate the prompt replies.
oh i just realized my SIM wasn't even in the phone while I was doing this (since I took it out during the white screen fix) -- would putting the SIM back in still create the same problem if my phone isn't unlocked?
Laurentius26 said:
The only thing I can think about is that your phone is simlocked.
Click to expand...
Click to collapse
You mean CID-locked, right?
Perhaps you could try another CustomRUU. Check this one http://forum.xda-developers.com/showthread.php?t=334890
Gas Addict said:
Oh yes, that's true. I didn't realize I had to unlock my phone before I could start this process...I guess I confused it with CID unlocking or something.
I must have missed the part in the newbie FAQ about phones needing to be sim unlocked for all this stuff to work.
I guess I will have to get it unlocked first! Very much appreciate the prompt replies.
Click to expand...
Click to collapse
No, a SIM-lock does not affect flashing.
So you ran JumpSPL from your phone, saw USB displayed on the screen, unplugged the usb cable, replaced it and then ran the hardspl provided from the thread I linked you to? There is no soft resetting going on between seeing USB on the screen and initiating the hardspl flash.
arexben said:
So you ran JumpSPL from your phone, saw USB displayed on the screen, unplugged the usb cable, replaced it and then ran the hardspl provided from the thread I linked you to? There is no soft resetting going on between seeing USB on the screen and initiating the hardspl flash.
Click to expand...
Click to collapse
Hi arexben,
I actually was an idiot and soft reset after unplugging and then plugging in the USB and not seeing any change on the screen.
Now if I put JumpSPL on my PDA and try to run it, it won't run saying it can't be opened because its either not signed w/ a trusted certificate or one of its components cannot be found.
Thank you so much for everyone trying to help me ... so to clarify, my phone has not been unlocked from AT&T and I am assuming I should still be able to get this stuff working.
Thanks again!
Gas Addict said:
Hi arexben,
I actually was an idiot and soft reset after unplugging and then plugging in the USB and not seeing any change on the screen.
Now if I put JumpSPL on my PDA and try to run it, it won't run saying it can't be opened because its either not signed w/ a trusted certificate or one of its components cannot be found.
Thank you so much for everyone trying to help me ... so to clarify, my phone has not been unlocked from AT&T and I am assuming I should still be able to get this stuff working.
Thanks again!
Click to expand...
Click to collapse
Not sure, but try to install the sdkcerts first.
Download them here: http://www.cinetsystems.com/xda/Kaiser Cab Collections/SdkCerts.cab
bmueller77 said:
Not sure, but try to install the sdkcerts first.
Download them here: http://www.cinetsystems.com/xda/Kaiser Cab Collections/SdkCerts.cab
Click to expand...
Click to collapse
Installed the SdkCerts then tried running JumpSPL off the phone still can't run that program.
Any other ideas guys?
Thank you again!
Alright so I had previously tried to flash roms and failed miserably. I've been scouring this forum since before I got my Kaiser (I got it last Fri.) and I thought I understood how to flash. Anyways...fast forward after failing miserably, I'd been getting along with just .cab files and installing things that way....fast forward some more to my problem.
I was trying the steps found here:
http://forum.xda-developers.com/showthread.php?t=354061
And I got to the tricolor screen, and USB appeared at the bottom. Well...I unplugged and replugged it and Vista made the USB noises and now I have this "Safely Remove Hardware" icon in my task bar. Nothing is happening, I'm not sure if I'm supposed to remove the hardware, but I'm having some serious troubles. I just want to flash Dutty's v4 rom onto my device and gof rom there.
Someone please help me, if anyone is available now and they wouldn't mind walking me through fixing this my AIM is xdemented3x
Please please please, someone help me.
tldr; Cliff Notes
Stuck on tricolor screen after trying to flash JumpSPL 1.56-KAIS on my AT&T Tilt
KAIS1*0
SPL-1.56.Jump
CPLD-8
USB
did you hard-spl? what do you see on the tricolor screen?
did you try to simply connect the tilt to vista via miniusb and run the exe from duttys v4 rom?
do you have a win xp computer around?
I'm on campus in college, and only have my Vista laptop. If things get severe enough I can go home and use an XP Home pc.
KAIS1*0
SPL-1.56.Jump
CPLD-8
USB
^^^ Thats what I see on the screen.
Should I try to connect it and run the v4 exe while on the tri-color screen?
Thank YOU SO MUCH for trying to help me. (^_^)
From what I see, you have run the softSPL.jump on the device, so now you need to flash hardSPL from the pc - leave the device as is ...Once you have flashed HardSPL then you should be fine to flash roms
delta-101 said:
From what I see, you have run the softSPL.jump on the device, so now you need to flash hardSPL from the pc - leave the device as is ...Once you have flashed HardSPL then you should be fine to flash roms
Click to expand...
Click to collapse
I can't do anything, I'm stuck on the tri-color screen. Should I press the reset button with my stylus? I've tried holding down the power button to no avail.
No, dont reset phone yet, have you tried to flash HardSPL as per the instructions? ---- Phone NEEDS to be in the bootloader mode you described to be able to flash HardSPL
noyz said:
I'm on campus in college, and only have my Vista laptop. If things get severe enough I can go home and use an XP Home pc.
KAIS1*0
SPL-1.56.Jump
CPLD-8
USB
^^^ Thats what I see on the screen.
Should I try to connect it and run the v4 exe while on the tri-color screen?
Thank YOU SO MUCH for trying to help me. (^_^)
Click to expand...
Click to collapse
unfortunately it seems that your device is not hard-spl'd. if it had been, it would have shown:
SPL-1.0.OliPof.
from the tricolor screen, try to install the Hard-SPL. Read here:
http://forum.xda-developers.com/showthread.php?t=334679
it might happen that it deosnt run from the tricolor screen, case in which i wouldnt know what to do by heart, so only suggestion is to read first sticky posts and see if you may find some info in there.
Alright thank-you for your help guys.
I HAVE $5 for the person who leads me to getting my phone working with Dutty's v4 rom on there, just some incentive for you guys. I need this help asap!
you may try anyway to press the reset button. in case it does load windows, youre saved. in case it gets stuck, you press the 2 buttons on the righthand side of the kaiser (power and camera) and do a reset with both of them pressed and you end up again in Bootloader mode...
if you manage to get to windows, go for the Hard-spl in my post above.
You have'nt answered my question.. Have you tried to flash HardSPL from the PC whilst phone is in Tricolor mode? ( with USB showing at the bottom of the screen) If so what happens?
delta-101 said:
You have'nt answered my question.. Have you tried to flash HardSPL from the PC whilst phone is in Tricolor mode? ( with USB showing at the bottom of the screen)
Click to expand...
Click to collapse
I'm running the Hardspl v1.exe on my pc right now and I'm stuck at the instruction where it says "Make sure ActiveSync is enable, hit ENTER to start..."
I hit enter, and nothing has happened.
Ah,, you are trying 2 different methods at once!! you started by using the JumpSPL1.56-KAIS.zip from the thread you pointed to... you should download, and copy to folder on the pc the flash-hardSPL.zip from the SAME thread, then follow the instruction in THAT folder.. that does NOT require Activesync.. Or you could try the HardSPL.exe you are using, but with device booted to windows.. then you start with activesync.
ionutz6 said:
you may try anyway to press the reset button. in case it does load windows, youre saved. in case it gets stuck, you press the 2 buttons on the righthand side of the kaiser (power and camera) and do a reset with both of them pressed and you end up again in Bootloader mode...
if you manage to get to windows, go for the Hard-spl in my post above.
Click to expand...
Click to collapse
Tried the reboot, and it came up with an AT&T flash screen before hte 3g animation.
The splash screen said "Not For sale, Test Only" Or something like that.
I still dont' have my SIM or MicroSD card in and Windows had booted up. I'm about to try the Hard SPL.exe now.
delta-101 said:
Ah,, you are trying 2 different methods at once!! you started by using the JumpSPL1.56-KAIS.zip from the thread you pointed to... you should download, and copy to folder on the pc the flash-hardSPL.zip from the SAME thread, then follow the instruction in THAT folder.. that does NOT require Activesync..
Click to expand...
Click to collapse
Alright....so now that i'm back into windows should I do the JumpSPL thing again and wait till I get locked into the tri-color screen? Or should I try the flash-hardSPL while in windows? I'm confused....
delta-101 said:
Ah,, you are trying 2 different methods at once!! you started by using the JumpSPL1.56-KAIS.zip from the thread you pointed to... you should download, and copy to folder on the pc the flash-hardSPL.zip from the SAME thread, then follow the instruction in THAT folder.. that does NOT require Activesync.. Or you could try the HardSPL.exe you are using, but with device booted to windows.. then you start with activesync.
Click to expand...
Click to collapse
You, sir, are well on your way to winning...scratch that...earning $5, lol. It seems I have successfully flashed hardSPL to my device now. From here can I reinstall my SD and SIM cards and run Dutty's v4 .exe on my PC to install that?
Yep, if HardSPL flashed, you should be fine to flash the rom.. You no longer need to use the jumpSPL
delta-101 said:
Yep, if HardSPL flashed, you should be fine to flash the rom.. You no longer need to use the jumpSPL
Click to expand...
Click to collapse
Alrighty man, Thanks A CRAP TON!
One more thing though, when I downloaded the zip for dutty's v4 and tried to extract it with WinRar it gives me an "Unknown Method" error. Also, it never asks me for a password. How do I get through that?
EDIT** BTW Whats your paypal?
There is an answer to that in the Dutty V4 thread (post 2) - with alternate download - seems to work ok
OMG YES!!!!!!!!!!!
Its at 7% as I type this..just went up to 10% w00t...finally flashing a rom!!! THANK-YOU SO MUCH!!!!! You have just earned yourself $5!!!! THANKS SO much bro. Whats your paypal? PM it to me....I need to send you the money, thanks again SO MUCH! You definitely earned this...
Dont worry, glad to help..
ok this is the wierdest thing ever. Yesterday I soft reset my phone (which was flashed to HardSPL and SuperCID and the Hyperdragod II rom about 2 weeks ago) and it now only goes to the bootloader screen. I ran mtty and did a boot command and the phone boots! But as soon as I softreset it goes back to the bootloader screen. Please note it wasnt a bad flash or anything because since I flashed 2 weeks ago my phone has worked 100% fine, soft resets and everything worked. I tried flashing to the original Kaiser bootloader, I flashed back to the original HTC rom and it still does this. One thing I noticed is that when I use mtty to boot and plug in my phone via usb my Windows XP PC doesnt start activesync, windows says it cannot recognize the plugged in usb device! However in tricolor mode I can still flash 100% so I dont think the usb port is defective.
same here..
the phone was hanging at night... wanted to reboot.. and tricolor..
Now I am using it for months.. an something it boots ok and sometimes I have to use MTTY or waiting without the battery in it for 10 min solves it sometimes to.
gone install 6.1 now.. hope it fixes it.
what does it display at bootloader screen?
sorry to jump in, but mine's started doing this today.
I had it flashed with 'Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06', which seemed to be working OK.
Then I soft reset it earlier today and got to loading my tday screen, screamed the battery was dead (it was nearly fully charged) and turned off.
I turned it back on and it was as though it was booting after the soft reset, or like I'd taken the battery out (I hadn't).
I couldn't get this to change, so I flashed it with Sleuth v3.0, one ive used very successfully before - now it only shows the tri-colour bootloader screen, with the following details:
KAIS130 MFG
SPL-1.0.0.oliPoF
CPLD-8
USB
Anyone know what I can do?
Thanks in advance
'tunes
Do the letters RUUNBH appear anywhere on the screen. LOOK AGAIN!
If so I can help easily, if not It'll take a little homework on your part. Let me know.
the exact text from the bootloader screen is:
KAIS130 MFG
SPL-1.0.OLIPOF
CPLD-8
Down the bottom it says Serial, or USB if it's connected to my PC.
(these may have changed from earlier, ive been trying all sorts to get this going properly!)
Thanks for your help
mad_tunes said:
the exact text from the bootloader screen is:
KAIS130 MFG
SPL-1.0.OLIPOF
CPLD-8
Down the bottom it says Serial, or USB if it's connected to my PC.
(these may have changed from earlier, ive been trying all sorts to get this going properly!)
Thanks for your help
Click to expand...
Click to collapse
I answered you in the other thread. Use one thread for correspondence, we don't need 15 different threads & posts about the same thing.
Help!
I have the same problem descripted in this thread but I wasn't able to find the other thread you are talking about with the answer... Is there anybody here who would help an unlucky tytn2 owner? Thank you so much... I'm waiting for you!
Hello to all, I am a noob here and have tried to adhere to all of the demands to do research and not post ?'s, but I am at a wall.
I have a Tilt and I ran the sim unlock and I was using the Sleuth 3.0 on it. Everything was working fine. I added the Iunlock cab and it worked fine as well. I then tried to install the icontacts, but i would have to go to program files and icontacts file in order to use I contacts. Well, wanna be innovative me thinks to try and move that file so it would replace something. I copied it to the windows appbuttons folder and deleted the regular contacts and nothing happened, then I put it in the start up folder and no luck, then I simply copied it to the windows folder not at the bottom where all of the extra files are. After that I tried to reset it and now all that I get is the bootloader screen. it reads as follows:
KAIS1*0 MFG
SPL-1.0.Olipof
CPLD-8
At the bottom, it shows either USB or Serial depending on if the usb is plugges up.
I tried running the sim unlock again and the dutty rom and both load to 100% but it goes back to the same screen. Any help would be greatly appreciated. Please help and thank you so much.
barrnunn said:
Hello to all, I am a noob here and have tried to adhere to all of the demands to do research and not post ?'s, but I am at a wall.
I have a Tilt and I ran the sim unlock and I was using the Sleuth 3.0 on it. Everything was working fine. I added the Iunlock cab and it worked fine as well. I then tried to install the icontacts, but i would have to go to program files and icontacts file in order to use I contacts. Well, wanna be innovative me thinks to try and move that file so it would replace something. I copied it to the windows appbuttons folder and deleted the regular contacts and nothing happened, then I put it in the start up folder and no luck, then I simply copied it to the windows folder not at the bottom where all of the extra files are. After that I tried to reset it and now all that I get is the bootloader screen. it reads as follows:
KAIS1*0 MFG
SPL-1.0.Olipof
CPLD-8
At the bottom, it shows either USB or Serial depending on if the usb is plugges up.
I tried running the sim unlock again and the dutty rom and both load to 100% but it goes back to the same screen. Any help would be greatly appreciated. Please help and thank you so much.
Click to expand...
Click to collapse
You could hard reset if you altered something in WM to cause it not to boot...hopefully
I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?
barrnunn said:
I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?
Click to expand...
Click to collapse
Yeah and then you press send...
- well you could try go into the bootloader and flash an OEM original ROM on i do not believe that doing this would brick your kaiser.
zeezee said:
You could hard reset if you altered something in WM to cause it not to boot...hopefully
Click to expand...
Click to collapse
In case u dont know how to do it:
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Resets
Or else search for MTTY. That helped a lot of ppl who got stuck in boot loader.
barrnunn said:
I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?
Click to expand...
Click to collapse
U need to hold the stylus in the hole longer, untl a message pops up on the page.
If it does not hardreset or help u, do what zeezee told u - flash a new rom.
OK, thank you all for you diligent assistance. I have tried the hard reset and it does the same thing...goes to black for about 2 seconds, then for a very split second goes to a grey screen and flashes loading then back to the bootloader.
I will try a search for the people stuck in bootloader and try flashing a OEM ROM, I will let you know how it goes. Thanks again.
barrnunn said:
OK, thank you all for you diligent assistance. I have tried the hard reset and it does the same thing...goes to black for about 2 seconds, then for a very split second goes to a grey screen and flashes loading then back to the bootloader.
I will try a search for the people stuck in bootloader and try flashing a OEM ROM, I will let you know how it goes. Thanks again.
Click to expand...
Click to collapse
Here is a list of OEM ROMs:http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
I do not see any Mods here around or somebody yelling (search button is your friend,search the wiki everything is there, bla bla)To having a woman at home change everything.. Thanks..!
Before you try the dangerous MTTY method, you could try refresh a oem rom w/ the SD method
ok, I am flashing an OEM rom now, but what does it mean to do it with the sd method?
barrnunn said:
ok, I am flashing an OEM rom now, but what does it mean to do it with the sd method?
Click to expand...
Click to collapse
From youre sd card (memorycard), look it up in wiki. Moust of us flashaholics keeps oure rom on oure memorycard and just rename the rom/bootsplash/radio or whateva and place it in root then activate bootloader -> flash. This is an alternative for not using usb cable, pc and active sync
http://wiki.xda-developers.com/index.php?pagename=KaiserSDFlash
ok thanks, but am i correct in understanding that to do that I have to use the phone to access the mem card?
My issue is that the only screen I get is bootloader, no nothing else. I can't even turn it off. I can take the battery out to get a black screen, but any action to try something will take it back to the bootloader screen. But for some reason, it still allows me to flash the ROM, I think. I flash it on my pc and then my phone goes to the grey screen where it shows the % of progress. It reaches 100% and the pc tells me to click finished and I do then it goes back to the bootloader.
barrnunn said:
ok thanks, but am i correct in understanding that to do that I have to use the phone to access the mem card?
My issue is that the only screen I get is bootloader, no nothing else. I can't even turn it off. I can take the battery out to get a black screen, but any action to try something will take it back to the bootloader screen. But for some reason, it still allows me to flash the ROM, I think. I flash it on my pc and then my phone goes to the grey screen where it shows the % of progress. It reaches 100% and the pc tells me to click finished and I do then it goes back to the bootloader.
Click to expand...
Click to collapse
put the rom image file on storage card and than power on phone in bootloader. the process will start automatically.
thesire said:
put the rom image file on storage card and than power on phone in bootloader. the process will start automatically.
Click to expand...
Click to collapse
yes, just use a card adapter or something to acess youre card (if you cant connect via active sync) then copy the rom over and follow the steps in wiki. Beeing stuck in the bootloader some times aint the worse place to be stuck
korakesion said:
I do not see any Mods here around or somebody yelling (search button is your friend,search the wiki everything is there, bla bla)To having a woman at home change everything.. Thanks..!
Click to expand...
Click to collapse
I don't mean to argue with you here and you are right about research threads, but honestly it's easy to get caught up in frustration with the amount of information. Some authors are good at documentation and some skip steps along the way or extra links are in the threads.
I just switched over to Gullum's Diamond Rom and was I nervous upgrading "Yes" and did I read much that I could "Yes". Were the instructions to HardSPL, Jump were a little unclear "Yes" so people asking questions are legit to a degree but we shouldn't also be eagar to pounce on...
tvos
tvos said:
I don't mean to argue with you here and you are right about research threads, but honestly it's easy to get caught up in frustration with the amount of information. Some authors are good at documentation and some skip steps along the way or extra links are in the threads.
I just switched over to Gullum's Diamond Rom and was I nervous upgrading "Yes" and did I read much that I could "Yes". Were the instructions to HardSPL, Jump were a little unclear "Yes" so people asking questions are legit to a degree but we shouldn't also be eagar to pounce on...
tvos
Click to expand...
Click to collapse
I agree with some of your remarks. Yes myself and others have jumped down people's throats yelling, "Search." One thing you have to remember though this is a developers forum, not a novice forum to help people making there phone look "cool."
Going into flashing / upgrading / modifying, you have to have a little bit of knowledge or time using Windows Mobile / Windows in General devices and machines.
Usually reading some background information can be a world a difference before jumping into this sort of thing.
I found the problem to stuck in bootloader. Thanks to all who have posted threads.
Originally Posted by GSLEON3
Many of you have noticed that in the past I spent a great deal of time helping people with Kaiser issues. Many of you have asked for help in the last few days & are probably feeling ignored. I am just unavailable at this time. My little sister had a Kidney Transplant operation on June 30th, 2008 & I have been spending much time traveling back & forth between my home in California & her's in Arizona. There were a few complications, but she is now doing well & recovering. I will be spending this weekend & most of next week helping to care for her & will be unavailable still for the next ten days or so.
There are many capable people in the Kaiser forum that will help. If you have hit a wall, be patient & I will begin to answer my PM's in the order they were recieved within the next week. Sorry I can't be of more help at the moment, but family comes first as I'm sure you understand.
Thanks,
GSLEON3
Aboslutely man. You go take care of your family. I will pray for God to guide you all through this trying time.
On the Kaiser note, I found after further studying of some threads, a solution to my issue where I was stuck in bootloader. I think this will apply to anyone that is stuck in bootloader with the usb/serial showing at the bottom and when they try to flash a new rom is goes to 100%, but the are still stuck on the boot screen.
After reading more threads, it appeared that there was some sort of disconnect between the usb and the phone. Since my PC was stating that it was successfully completing the flash, that shows that it was not getting any type of error from the phone. After reading a thread I simply blew in my tilt usb port and used my stylus to try to straighten it out as one of your post state to ensure the usb connection is straightor it may give mtty an issue.
Once I messed with my USB port, the phone came back to life and everything was fine. Everything was rebooted and all my info was lost however. I was even able to successfully flash a new ROM.
In closing, if anyone is stuck in bootloader mode and their flash goes to 100% and doesn't fix their issue, tell them to clean and straighten their usb connection.
Solution for Those Stuck in Bootloader
Here is the link to the initial thread I started for my issue
http://forum.xda-developers.com/showthread.php?t=406221
I found after further studying of some threads, a solution to my issue where I was stuck in bootloader. I think this will apply to anyone that is stuck in bootloader with the usb/serial showing at the bottom and when they try to flash a new rom is goes to 100%, but the are still stuck on the boot screen.
After reading more threads, it appeared that there was some sort of disconnect between the usb and the phone. Since my PC was stating that it was successfully completing the flash, that shows that it was not getting any type of error from the phone. After reading a thread I simply blew in my tilt usb port and used my stylus to try to straighten it out as one of your post state to ensure the usb connection is straightor it may give mtty an issue.
Once I messed with my USB port, the phone came back to life and everything was fine. Everything was rebooted and all my info was lost however. I was even able to successfully flash a new ROM.
In closing, if anyone is stuck in bootloader mode and their flash goes to 100% and doesn't fix their issue, tell them to clean and straighten their usb connection.
Okay I got up this morning and my phone was working fine. But then I restarted it and it just booted to the tri-color screen. So i took out the battery and I did a reset and it just keeps comming back.
So I thought that the rom might have went bad, dont know how but I though I would just refalsh it to see if it works. I flashed correctly and said it was complete but just reboot back to the tri-color screen. So the flash will complete fine but cannot get out of boot loader. I tryed flashing original and cooked rom, same result.
So I thought I would try and flash back to an older hard spl, I have hardspl 3.29 right now so I thought I would try hardspl 3.28 just to see if issue would be fixed. So I flash it and it completes, then reboots to tri-color again, but instead of saying 3.28 like it should it still says 3.29. Wierd??
So I through I would give mtty a try and see if I could get past the boot loader. I tryed the boot command which gave me a command error so I did some searching and tryed:
"set 16 0"
"task 8" <- causes phone to restart and goes back to tri-color.
Right now I am stuck at this tri-color screen and I think I am never going to get out. This came up randomly my phone has been working fine for a while now until today.
Can someone please help me on how to make it work????
Thank you to anyone who provides help.
Hi sngskunk, I have a similar problem. After a radio flashing, my phone stopped in tri-color screen, returned to normal after 24h, then returned to hang on tri-color screen. By coincidence it happened after using the camera. I suspect that might be a hardware problem, maybe a short circuit in the camera button, but I will make sure after opening the unit and clean the contacts of the button.
I am going to try and take the phone apart and look at the camera button to see if that is the problem, but is there a command in mtty that will boot the os, after the bootloader.
Because i have tryed the boot command and that doesn't work in Hardspl 3.29, I get a cammand error. I have tryed resetting it but if the camera button is stuck then it is going to go back to the original tri-color screen.
Okay so I toke my phone apart to check the camera button, the button looks fine didnt look dirty or full of dust and I check the micro switch and it seemed okay. While the phone was a part I turned it on to check to see if it would boot to the os, but it didnt it stopped at the spl, and I know that the camera button wasnt pushed.
Going to try and install a new radio just to see if that fixes it, if not, I am all out of ideas.
sngskunk said:
Okay so I toke my phone apart to check the camera button, the button looks fine didnt look dirty or full of dust and I check the micro switch and it seemed okay. While the phone was a part I turned it on to check to see if it would boot to the os, but it didnt it stopped at the spl, and I know that the camera button wasnt pushed.
Going to try and install a new radio just to see if that fixes it, if not, I am all out of ideas.
Click to expand...
Click to collapse
Try flashing a shipped ROM via MicroSD
I tryed installing a radio by itself, didnt fix it.
Installed original shipped rom from microsd, flash when perfect, said it was complete, reset it phone and it came back to the tri-color screen.
There is no "RUU**" i dont know what else is in that string but some people get in at the top of the screen when they are having my problem, but mine does not have it.
I would try going though the FrankenKaiser steps and see if that works? Just an idea
I looked up the post you are talking about and I am confused on it, because if I have the phone connected with the usb cable and use mtty. There is no command named dload.
Code:
cmd>dload
Command error !!!
Ofcouse now that I look at that post again that was in the spl, I cannot get to the radio boot loader the way he says, holding down the green phone and turning on the phone doesnt work just boots into the spl again.
Okay well i found a good post on how to do it but I get errors on the commands becuase in the post he isnt using hardspl 3.29 the cammand is the following:
rtask a <--- gets command error
austinsnyc said:
I would try going though the FrankenKaiser steps and see if that works? Just an idea
Click to expand...
Click to collapse
austinsnyc,
using these steps? -> http://forum.xda-developers.com/showthread.php?t=394584
I tryed those steps, but didnt work it wont go into radio boot loader mode.
I also tryed these steps: http://forum.xda-developers.com/showthread.php?t=393337
But I cannot execute the command: "rtask a", I get a command error.
sngskunk said:
I tryed those steps, but didnt work it wont go into radio boot loader mode.
I also tryed these steps: http://forum.xda-developers.com/showthread.php?t=393337
But I cannot execute the command: "rtask a", I get a command error.
Click to expand...
Click to collapse
I try these steps on saturday, but hardspl 3.* don't suport rtask command . If nothing more resolve, I am putting my chips on this tool (read post 6) ->http://forum.xda-developers.com/showthread.php?t=415839
I've run into the exact same problem.
I just turned off my phone, turned it back on and now it's just stuck.. can't load anything.
2nd time i've had a problem with this phone
Ok so i've also noticed something else with this problem.
Basically, what had happened, I did the same thing as the first post. All I did was reset my phone. I turned it back on, and i'm stuck at bootloader screen
When it is loading, it flashes the screen to a complete white screen that says "Loading. No Image File!"
Then it goes right back to the bootloader screen and that's that.
It seems as though hard resetting, mtty or flashing back to original rom does not work.
Does anyone know what the heck is going on?
@kjb, have you tried the suggestions by AllTheWay and myself in the other thread you posted in. It's very hard to keep up when issues are on going in 2 threads. Please stick to just one, I suggest the other one.
Link here: http://forum.xda-developers.com/showthread.php?t=418692
Thanks
Dave
DaveShaw said:
@kjb, have you tried the suggestions by AllTheWay and myself in the other thread you posted in. It's very hard to keep up when issues are on going in 2 threads. Please stick to just one, I suggest the other one.
Link here: http://forum.xda-developers.com/showthread.php?t=418692
Thanks
Dave
Click to expand...
Click to collapse
Hi Dave,
Yes I have tried flashing the original rom. But unfortunately, i'm still stuck at the bootloader screen and it did nothing.
I am extremely confused now
kjb86 said:
Hi Dave,
Yes I have tried flashing the original rom. But unfortunately, i'm still stuck at the bootloader screen and it did nothing.
I am extremely confused now
Click to expand...
Click to collapse
Tri the link in my sig, There are some suggestions in the Wiki.
Ta
Dave
DaveShaw said:
Tri the link in my sig, There are some suggestions in the Wiki.
Ta
Dave
Click to expand...
Click to collapse
hmmmm, ok for mtty it's not working. There is no USB present and I can't select it.
It won't allow me to do any of the settings just by selecting COM1 or COM2.
kjb86 said:
hmmmm, ok for mtty it's not working. There is no USB present and I can't select it.
It won't allow me to do any of the settings just by selecting COM1 or COM2.
Click to expand...
Click to collapse
Did you disable USB connections first?
AllTheWay said:
Did you disable USB connections first?
Click to expand...
Click to collapse
No. Nothing was disabled. Activesync was not present at all either and nothing was in the task manager.
Few things i've noticed:
a) when flashing to a new rom (or attempting too) there is no image listed in the previous ROM
b) my phone would be off, I'll plug it in to the USB and all of a sudden my phone will turn on right to bootloader.
Don't know if that makes a difference, but it's just some observations for you guys.
kjb86 said:
No. Nothing was disabled. Activesync was not present at all either and nothing was in the task manager.
Few things i've noticed:
a) when flashing to a new rom (or attempting too) there is no image listed in the previous ROM
b) my phone would be off, I'll plug it in to the USB and all of a sudden my phone will turn on right to bootloader.
Don't know if that makes a difference, but it's just some observations for you guys.
Click to expand...
Click to collapse
No you need to disabled USB connections in Activesync for MTTY to work!