Okay I got up this morning and my phone was working fine. But then I restarted it and it just booted to the tri-color screen. So i took out the battery and I did a reset and it just keeps comming back.
So I thought that the rom might have went bad, dont know how but I though I would just refalsh it to see if it works. I flashed correctly and said it was complete but just reboot back to the tri-color screen. So the flash will complete fine but cannot get out of boot loader. I tryed flashing original and cooked rom, same result.
So I thought I would try and flash back to an older hard spl, I have hardspl 3.29 right now so I thought I would try hardspl 3.28 just to see if issue would be fixed. So I flash it and it completes, then reboots to tri-color again, but instead of saying 3.28 like it should it still says 3.29. Wierd??
So I through I would give mtty a try and see if I could get past the boot loader. I tryed the boot command which gave me a command error so I did some searching and tryed:
"set 16 0"
"task 8" <- causes phone to restart and goes back to tri-color.
Right now I am stuck at this tri-color screen and I think I am never going to get out. This came up randomly my phone has been working fine for a while now until today.
Can someone please help me on how to make it work????
Thank you to anyone who provides help.
Hi sngskunk, I have a similar problem. After a radio flashing, my phone stopped in tri-color screen, returned to normal after 24h, then returned to hang on tri-color screen. By coincidence it happened after using the camera. I suspect that might be a hardware problem, maybe a short circuit in the camera button, but I will make sure after opening the unit and clean the contacts of the button.
I am going to try and take the phone apart and look at the camera button to see if that is the problem, but is there a command in mtty that will boot the os, after the bootloader.
Because i have tryed the boot command and that doesn't work in Hardspl 3.29, I get a cammand error. I have tryed resetting it but if the camera button is stuck then it is going to go back to the original tri-color screen.
Okay so I toke my phone apart to check the camera button, the button looks fine didnt look dirty or full of dust and I check the micro switch and it seemed okay. While the phone was a part I turned it on to check to see if it would boot to the os, but it didnt it stopped at the spl, and I know that the camera button wasnt pushed.
Going to try and install a new radio just to see if that fixes it, if not, I am all out of ideas.
sngskunk said:
Okay so I toke my phone apart to check the camera button, the button looks fine didnt look dirty or full of dust and I check the micro switch and it seemed okay. While the phone was a part I turned it on to check to see if it would boot to the os, but it didnt it stopped at the spl, and I know that the camera button wasnt pushed.
Going to try and install a new radio just to see if that fixes it, if not, I am all out of ideas.
Click to expand...
Click to collapse
Try flashing a shipped ROM via MicroSD
I tryed installing a radio by itself, didnt fix it.
Installed original shipped rom from microsd, flash when perfect, said it was complete, reset it phone and it came back to the tri-color screen.
There is no "RUU**" i dont know what else is in that string but some people get in at the top of the screen when they are having my problem, but mine does not have it.
I would try going though the FrankenKaiser steps and see if that works? Just an idea
I looked up the post you are talking about and I am confused on it, because if I have the phone connected with the usb cable and use mtty. There is no command named dload.
Code:
cmd>dload
Command error !!!
Ofcouse now that I look at that post again that was in the spl, I cannot get to the radio boot loader the way he says, holding down the green phone and turning on the phone doesnt work just boots into the spl again.
Okay well i found a good post on how to do it but I get errors on the commands becuase in the post he isnt using hardspl 3.29 the cammand is the following:
rtask a <--- gets command error
austinsnyc said:
I would try going though the FrankenKaiser steps and see if that works? Just an idea
Click to expand...
Click to collapse
austinsnyc,
using these steps? -> http://forum.xda-developers.com/showthread.php?t=394584
I tryed those steps, but didnt work it wont go into radio boot loader mode.
I also tryed these steps: http://forum.xda-developers.com/showthread.php?t=393337
But I cannot execute the command: "rtask a", I get a command error.
sngskunk said:
I tryed those steps, but didnt work it wont go into radio boot loader mode.
I also tryed these steps: http://forum.xda-developers.com/showthread.php?t=393337
But I cannot execute the command: "rtask a", I get a command error.
Click to expand...
Click to collapse
I try these steps on saturday, but hardspl 3.* don't suport rtask command . If nothing more resolve, I am putting my chips on this tool (read post 6) ->http://forum.xda-developers.com/showthread.php?t=415839
I've run into the exact same problem.
I just turned off my phone, turned it back on and now it's just stuck.. can't load anything.
2nd time i've had a problem with this phone
Ok so i've also noticed something else with this problem.
Basically, what had happened, I did the same thing as the first post. All I did was reset my phone. I turned it back on, and i'm stuck at bootloader screen
When it is loading, it flashes the screen to a complete white screen that says "Loading. No Image File!"
Then it goes right back to the bootloader screen and that's that.
It seems as though hard resetting, mtty or flashing back to original rom does not work.
Does anyone know what the heck is going on?
@kjb, have you tried the suggestions by AllTheWay and myself in the other thread you posted in. It's very hard to keep up when issues are on going in 2 threads. Please stick to just one, I suggest the other one.
Link here: http://forum.xda-developers.com/showthread.php?t=418692
Thanks
Dave
DaveShaw said:
@kjb, have you tried the suggestions by AllTheWay and myself in the other thread you posted in. It's very hard to keep up when issues are on going in 2 threads. Please stick to just one, I suggest the other one.
Link here: http://forum.xda-developers.com/showthread.php?t=418692
Thanks
Dave
Click to expand...
Click to collapse
Hi Dave,
Yes I have tried flashing the original rom. But unfortunately, i'm still stuck at the bootloader screen and it did nothing.
I am extremely confused now
kjb86 said:
Hi Dave,
Yes I have tried flashing the original rom. But unfortunately, i'm still stuck at the bootloader screen and it did nothing.
I am extremely confused now
Click to expand...
Click to collapse
Tri the link in my sig, There are some suggestions in the Wiki.
Ta
Dave
DaveShaw said:
Tri the link in my sig, There are some suggestions in the Wiki.
Ta
Dave
Click to expand...
Click to collapse
hmmmm, ok for mtty it's not working. There is no USB present and I can't select it.
It won't allow me to do any of the settings just by selecting COM1 or COM2.
kjb86 said:
hmmmm, ok for mtty it's not working. There is no USB present and I can't select it.
It won't allow me to do any of the settings just by selecting COM1 or COM2.
Click to expand...
Click to collapse
Did you disable USB connections first?
AllTheWay said:
Did you disable USB connections first?
Click to expand...
Click to collapse
No. Nothing was disabled. Activesync was not present at all either and nothing was in the task manager.
Few things i've noticed:
a) when flashing to a new rom (or attempting too) there is no image listed in the previous ROM
b) my phone would be off, I'll plug it in to the USB and all of a sudden my phone will turn on right to bootloader.
Don't know if that makes a difference, but it's just some observations for you guys.
kjb86 said:
No. Nothing was disabled. Activesync was not present at all either and nothing was in the task manager.
Few things i've noticed:
a) when flashing to a new rom (or attempting too) there is no image listed in the previous ROM
b) my phone would be off, I'll plug it in to the USB and all of a sudden my phone will turn on right to bootloader.
Don't know if that makes a difference, but it's just some observations for you guys.
Click to expand...
Click to collapse
No you need to disabled USB connections in Activesync for MTTY to work!
Related
i tried flashing a non-factory rom to my tilt. the steps i took are listed below.
tried the hardspl utility. got a white screen.
tried the hardspl utility for white screen devices. got the tri-color screen. yay.
ran the custom flasher that came with the custom rom i wanted to try.
got to 27% and stopped. it asked for a restart.
all subsequent flashes get to 0%.
went to the "how to revert" thread and grabbed the att factory rom.
ran the utility. utility returns "invalid vendor id" error.
my tilt shipped with 1.62.00, but the utility tries to install 1.57.502.2. does this matter?
how do i unbrick my phone?
--RC
rafadavidc said:
i tried flashing a non-factory rom to my tilt. the steps i took are listed below.
tried the hardspl utility. got a white screen.
tried the hardspl utility for white screen devices. got the tri-color screen. yay.
ran the custom flasher that came with the custom rom i wanted to try.
got to 27% and stopped. it asked for a restart.
all subsequent flashes get to 0%.
went to the "how to revert" thread and grabbed the att factory rom.
ran the utility. utility returns "invalid vendor id" error.
my tilt shipped with 1.62.00, but the utility tries to install 1.57.502.2. does this matter?
how do i unbrick my phone?
--RC
Click to expand...
Click to collapse
is your phone stuck at tricolor screen? If so tell me what it says.
{red band upper right corner}
RUUNBH
{red band lower left corner}
KAIS1*0
SPL-1.93.0000
CPLD-8
{green band}
{blue band}
{white band top center}
USB
--RC
rafadavidc said:
{red band upper right corner}
RUUNBH
{red band lower left corner}
KAIS1*0
SPL-1.93.0000
CPLD-8
{green band}
{blue band}
{white band top center}
USB
--RC
Click to expand...
Click to collapse
Looks like hardspl was never installed. Is your device stuck on that screen?
redbandana said:
Looks like hardspl was never installed. Is your device stuck on that screen?
Click to expand...
Click to collapse
I'd say Hardspl wasnt installed properly. Did you have enough battery life when you started the install of the rom? After a bad install of hardspl, I would ahve tried to reinstall it from the beginning again just to make sure you didnt have any problems. For now, try to pull up hardspl by holding in the power button/camera button (pressed really hard), and pressing the soft reset button in. If you do it right, the tri-color screen should come up. Then try reflashing hardspl if you can, or trying the rom again.
If that doesnt work, if you have At&t you can always connect it to a car battery and let it fry. Just don't cause any damage to the phone physically or with water. Otherwise, it doesnt matter.. you can warranty exchange it.
i followed the instructions for white-screeners.
copy 1.56, see if it white-screens. if it does, copy 1.93 and try again.
got the color bands? good. make the connection and flash away.
right?
--RC
rafadavidc said:
i followed the instructions for white-screeners.
copy 1.56, see if it white-screens. if it does, copy 1.93 and try again.
got the color bands? good. make the connection and flash away.
right?
--RC
Click to expand...
Click to collapse
you still need to install hardspl.
nimda0 said:
I'd say Hardspl wasnt installed properly. Did you have enough battery life when you started the install of the rom?
Click to expand...
Click to collapse
yes.
After a bad install of hardspl, I would ahve tried to reinstall it from the beginning again just to make sure you didnt have any problems. For now, try to pull up hardspl by holding in the power button/camera button (pressed really hard), and pressing the soft reset button in. If you do it right, the tri-color screen should come up.
Click to expand...
Click to collapse
doing this does exactly the same thing as simply applying power.
Then try reflashing hardspl if you can, or trying the rom again.
Click to expand...
Click to collapse
ok, this is probably where i'm not clear. i was under the impression that installing hardspl is as simple as getting to the tri-color screen without white-screening with one of the jumpspl files.
If that doesnt work, if you have At&t you can always connect it to a car battery and let it fry. Just don't cause any damage to the phone physically or with water. Otherwise, it doesnt matter.. you can warranty exchange it.
Click to expand...
Click to collapse
connect what to the car battery? the +/- contacts as illustrated on the phone battery?
--RC
redbandana said:
you still need to install hardspl.
Click to expand...
Click to collapse
as i stated, the thread isn't very clear on this. i tried running the hardspl utility, but it whitescreened. i ran the alternate one for white-screeners and it got me to the tri-color screen. what else is there?
i tried resetting the phone and rerunning the hardspl utility after successfully getting the tri-color screen, but it just whitescreened again.
--RC
rafadavidc said:
yes.
doing this does exactly the same thing as simply applying power.
ok, this is probably where i'm not clear. i was under the impression that installing hardspl is as simple as getting to the tri-color screen without white-screening with one of the jumpspl files.
connect what to the car battery? the +/- contacts as illustrated on the phone battery?
--RC
Click to expand...
Click to collapse
dude your phone isn't broken. you need to stop focusing on what is stated there and listen to what I am saying. You need to install hardspl. 1.93 is only if you were receiving a white screen. Install hardspl let me know what happens. I'll be up for another 1/2 hour customizing a rom.
The new SPL should work. I also got white screen with HardSPL and SPL. But the new one worked on my 2 new dievices.
xmoo said:
The new SPL should work. I also got white screen with HardSPL and SPL. But the new one worked on my 2 new dievices.
Click to expand...
Click to collapse
he can't flash with 1.93 it stalls at 0%. I was under the impression 1.93 is one of the original ATT spl's.
i'm sorry, i didn't mean i'm ready to run out and fry my phone right now, i'd rather fix it.
i guess i'm unclear on what it means to install hardspl. running the .exe from here just does nothing. is there something i'm missing?
--RC
rafadavidc said:
i'm sorry, i didn't mean i'm ready to run out and fry my phone right now, i'd rather fix it.
i guess i'm unclear on what it means to install hardspl. running the .exe from here just does nothing. is there something i'm missing?
--RC
Click to expand...
Click to collapse
Probably not Pof writes clear instructions. Follow his instructions to a T. Since you are receiving white screen follow jockey's instructions here:
http://forum.xda-developers.com/showthread.php?t=354061
ah, ok, see, this is where i have not been clear.
my phone boots to the tri-color screen and does absolutely nothing else. i'm stuck here, unless there's some magical button combination that will get me back into windows. i can't get it to boot to the operating environment.
--RC
Umm, can't you just soft-reset to get back to windows from where you are? No magic button combination needed.
soft-reset gets me back to the tri-color screen.
--RC
rafadavidc said:
soft-reset gets me back to the tri-color screen.
--RC
Click to expand...
Click to collapse
is your camera button stuck down somehow?
no, it was responding nicely earlier today, and i can also feel the distinctive two-click action now if i play with it.
--RC
rafadavidc said:
soft-reset gets me back to the tri-color screen.
--RC
Click to expand...
Click to collapse
ok this is what i originally asked "are you stuck at tri color screen?"
follow these instructions and stop ****ing yourself over by reading everyone's post at once: (who else helps n00bs at 5am)
First download attached file: Next follow these steps
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
Ok, So I had dutty's rom running perfect for about 5 months. Decided I wanted to revert back to the stock ATT rom and play with it. I tried to revert and somewhere along the way, I did a soft reset and it screwed me up. I can still flash roms no problem, but for some reason, when the phone goes to start up, it gets to the first screen of the boot process (white with ATT logo) and then it freezes. After about 10-15 seconds, it automatically soft resets and tries again. So, I can hit the reset button while holding cam and pwr to get to the bootloader. I have tried flashing every rom I have downloaded, and nothing seems to work. I am trying the stock ATT rom as I type this but we will see what happens. That is what I was running when it F'd. I wanted to restore it to stock completely, thought about trying to have it replaced because the hinge is really loose on my handset. Anyway, any help would be appreciated. Thanks!
boot command from mtty reads:
Cmd>boot
InitDisplay: Display_Chip=1
Fill RSVD information for block 288 to 309
Storage start sector=0xAB80, total sector=0x10740
Storage start block=707, total block=1053
Total Bad Block in CE: 0
Erase physical block from 995 to 2032
formatstorage Bad block found: 1045
si backup: Erase physical block from 2032 to 2048
No card inserted
OSSIPreLoad ++
Try this
Try flashing this ROM and see what happens.
http://www.4shared.com/file/3857459...ULAR_WWE_157_-_Originaly_Shipped_ATT_ROM.html
What does your bootloader screen show?
Please Help!
Okay. I tried to flash the OEM rom back to my ATT Tilt. While doing this, somehow my phone entered an unending cycle of soft resets. I can still get to the bootloader, but as soon as I flash a rom, it tries to boot, gets to the first boot screen, then resets. My computer keeps popping up "install drivers for new hardware found".
I tried booting through MTTY, no dice.
My bootloader screen reads:
KAIS1*0 MFG
SPL-1.0.01OliPof
CPLD-8
I tried flashing hardspl. RUU opens and it runs instantly. The phone reboots and the boot loader screen still reads this. I flash a new rom, the bootloader still reads this. I'm at a loss. I've been working on this for 3 hours and I haven't gotten anywhere. I don't have a backup phone, so I have to figure this problem out. I have searched the forums and haven't found anyone with the same problem. Please, anyone who feels they can help, let me know what I can try to fix this problem. Thanks!
Threads merged.
Metzex08 said:
Ok, So I had dutty's rom running perfect for about 5 months. Decided I wanted to revert back to the stock ATT rom and play with it. I tried to revert and somewhere along the way, I did a soft reset and it screwed me up. I can still flash roms no problem, but for some reason, when the phone goes to start up, it gets to the first screen of the boot process (white with ATT logo) and then it freezes. After about 10-15 seconds, it automatically soft resets and tries again. So, I can hit the reset button while holding cam and pwr to get to the bootloader. I have tried flashing every rom I have downloaded, and nothing seems to work. I am trying the stock ATT rom as I type this but we will see what happens. That is what I was running when it F'd. I wanted to restore it to stock completely, thought about trying to have it replaced because the hinge is really loose on my handset. Anyway, any help would be appreciated. Thanks!
Click to expand...
Click to collapse
Some people go to far ahead before figuring out the real issue. Don't **** yourself.
Hold down your power, camera, and insert your stylus then tell us what your bootloader screen displays.
Metzex08 said:
Okay. I tried to flash the OEM rom back to my ATT Tilt. While doing this, somehow my phone entered an unending cycle of soft resets. I can still get to the bootloader, but as soon as I flash a rom, it tries to boot, gets to the first boot screen, then resets. My computer keeps popping up "install drivers for new hardware found".
I tried booting through MTTY, no dice.
My bootloader screen reads:
KAIS1*0 MFG
SPL-1.0.01OliPof
CPLD-8
I tried flashing hardspl. RUU opens and it runs instantly. The phone reboots and the boot loader screen still reads this. I flash a new rom, the bootloader still reads this. I'm at a loss. I've been working on this for 3 hours and I haven't gotten anywhere. I don't have a backup phone, so I have to figure this problem out. I have searched the forums and haven't found anyone with the same problem. Please, anyone who feels they can help, let me know what I can try to fix this problem. Thanks!
Click to expand...
Click to collapse
ok post was moved from another thread. sorry. It appears that you do have hardspl installed.
Metzex08 said:
Okay. I tried to flash the OEM rom back to my ATT Tilt. While doing this, somehow my phone entered an unending cycle of soft resets. I can still get to the bootloader, but as soon as I flash a rom, it tries to boot, gets to the first boot screen, then resets. My computer keeps popping up "install drivers for new hardware found".
I tried booting through MTTY, no dice.
My bootloader screen reads:
KAIS1*0 MFG
SPL-1.0.01OliPof
CPLD-8
I tried flashing hardspl. RUU opens and it runs instantly. The phone reboots and the boot loader screen still reads this. I flash a new rom, the bootloader still reads this. I'm at a loss. I've been working on this for 3 hours and I haven't gotten anywhere. I don't have a backup phone, so I have to figure this problem out. I have searched the forums and haven't found anyone with the same problem. Please, anyone who feels they can help, let me know what I can try to fix this problem. Thanks!
Click to expand...
Click to collapse
and your bootloader screen will not change because it does not display the rom version. You have hardspl installed what more do you want?
Did you believe your bootloader screen would change after you flashed a rom?
Damn!!!
Metzex08 said:
Ok, So I had dutty's rom running perfect for about 5 months. Decided I wanted to revert back to the stock ATT rom and play with it. I tried to revert and somewhere along the way, I did a soft reset and it screwed me up. I can still flash roms no problem, but for some reason, when the phone goes to start up, it gets to the first screen of the boot process (white with ATT logo) and then it freezes. After about 10-15 seconds, it automatically soft resets and tries again. So, I can hit the reset button while holding cam and pwr to get to the bootloader. I have tried flashing every rom I have downloaded, and nothing seems to work. I am trying the stock ATT rom as I type this but we will see what happens. That is what I was running when it F'd. I wanted to restore it to stock completely, thought about trying to have it replaced because the hinge is really loose on my handset. Anyway, any help would be appreciated. Thanks!
Click to expand...
Click to collapse
Dude it has been five months since you flashed a rom why bother getting all neurotic and worried For a common situation? I complained to mods because they closed your thread now I look like a douche bag. Thanks.
I had the same problem (continuous reboot) as before, see this thread:
http://forum.xda-developers.com/showthread.php?t=383678
but the problem that I had is because of bad blocks, post your info 8 and maybe I can help
ok, I got the phone to startup, eventually it stopped trying to soft reset. I hit the power button and it turned on. Now, I run jumpspl and it doesn't ever bring up the USB connection, so I can't change the bootloader back to oem. any suggestions?
I used the other version of jumpspl (1.56) and it brought up the USB connection (atleast it says it did). But, when I try to run RUU from the ATT_SPL folder it cannot connect to my phone. MTTY says USB connection is unavailable as well. What should I do?! I want the phone to be able to be sent in for warranty replacement as the hinge seems to keep getting looser and looser. Any ideas? Bootloader still reads the same as before.
Metzex08 said:
I used the other version of jumpspl (1.56) and it brought up the USB connection (atleast it says it did). But, when I try to run RUU from the ATT_SPL folder it cannot connect to my phone. MTTY says USB connection is unavailable as well. What should I do?! I want the phone to be able to be sent in for warranty replacement as the hinge seems to keep getting looser and looser. Any ideas? Bootloader still reads the same as before.
Click to expand...
Click to collapse
If your sending it for warranty replacement via AT&T just put it in the microwave for 2 seconds....problem solved.
Okay. I tried to install one of Dutty's ROM's that can be found here: http://forum.xda-developers.com/showthread.php?t=398271.
I read through all the stickys and FAQ's first. I read Dutty's wiki, the Kaiser wiki, and the flashing new ROM wiki. I followed all of the directions and followed Dutty's instructions to the T.
After installing the HardSPL found here(http://forum.xda-developers.com/showthread.php?t=334679), I backed up all my personal info/data.
Then used the Custom RUU Dutty supplied and proceed through the ROM flashing process. Everything went fine and I got no error messages. But when my phone booted up I got a black screen. I waited but my phone stayed on the black screen. So I pressed the standby button on and off a few times and eventually I wound up with a black screen that had about a million multi-colored speckled dots all over it. And I have been stuck on this screen since. I've tried soft-reseting and hard resetting but nothing is working.
I am Using an ATT Tilt BTW.
Please Help me. My phone is my life so right now I'm feeling like Dionne Farris.....Hopeless....
ahh that sounds like a nightmare... wish i could help
klrob33 said:
Okay. I tried to install one of Dutty's ROM's that can be found here: http://forum.xda-developers.com/showthread.php?t=398271.
I read through all the stickys and FAQ's first. I read Dutty's wiki, the Kaiser wiki, and the flashing new ROM wiki. I followed all of the directions and followed Dutty's instructions to the T.
After installing the HardSPL found here(http://forum.xda-developers.com/showthread.php?t=334679), I backed up all my personal info/data.
Then used the Custom RUU Dutty supplied and proceed through the ROM flashing process. Everything went fine and I got no error messages. But when my phone booted up I got a black screen. I waited but my phone stayed on the black screen. So I pressed the standby button on and off a few times and eventually I wound up with a black screen that had about a million multi-colored speckled dots all over it. And I have been stuck on this screen since. I've tried soft-reseting and hard resetting but nothing is working.
I am Using an ATT Tilt BTW.
Please Help me. My phone is my life so right now I'm feeling like Dionne Farris.....Hopeless....
Click to expand...
Click to collapse
can you get into bootloader mode?
hold down power and camera button while inserting stylus it should introduce you to the tri color screen. Please tell us what it states. You may have just experienced a bad flash or you have the radio from hell installed on your device
redbandana said:
can you get into bootloader mode?
hold down power and camera button while inserting stylus it should introduce you to the tri color screen. Please tell us what it states. You may have just experienced a bad flash or you have the radio from hell installed on your device
Click to expand...
Click to collapse
Yes I can get to Bootloader mode.
In the red bar it says:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
And Serial at the bottom in the white bar where USB normaly would be.
klrob33 said:
Yes I can get to Bootloader mode.
In the red bar it says:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
And Serial at the bottom in the white bar where USB normaly would be.
Click to expand...
Click to collapse
ok soft reset your phone and when it starts up does something like this appear in red text?
r 1.65.20.29
g 25.88.40.04w
d 3.29.xx.xx
please tell me what it says after R
R- 1.58.25.17
klrob33 said:
R- 1.58.25.17
Click to expand...
Click to collapse
well it appears to be a bad flash. unplug your device from the usb cable, restart your computer, and flash again.
Hopefully after your computer restarts it will recognize the device as being connected. If it doesn't just double click on your windows mobile device center icon and it should connect. After connecting just reflash the rom
edit
I had the same problem, what i did was read all through the thread of the ROM or while inside the thread i use the search function and type in the keywords like "blank screen" it happened to me exactly, but i didnt bother to post since i found the answer, 1 user said flash it to WM 6.1 i did exactly that and it helped! some said not necessary, but i didnt see that instruction so i flashed the 6.1 blindly and fortunately it worked...
here is the thread
http://forum.xda-developers.com/showthread.php?t=375583&page=30
on the search function type black screen and you should get and idea what you need to do...
redbandana said:
well it appears to be a bad flash. unplug your device from the usb cable, restart your computer, and flash again.
Hopefully after your computer restarts it will recognize the device as being connected. If it doesn't just double click on your windows mobile device center icon and it should connect. After connecting just reflash the rom
edit
Click to expand...
Click to collapse
I tried that and It different work. I'm trying a whole new ROM now and I hope it works.
Problem solved.
Thanks to everybody for their help.
I just used a different ROM and everything worked perfectly. I guess that ROM just didn't want to work with my phone. But it's okay. The ROM I'm using now is perfect.
If the answer is one this site already I apologize to everyone but I have been searching for 3 days now and no joy.
I will try to keep is short and simple.
I have been flashing for the last year now and have never had trouble until now. Flashed Duttys ROM released on June 5th I believe. Went great but still had old HardSPL on my phone. Followed the steps to flash latest SPL 3.29 and it never took. As a matter of fact something happened to the USB and my pc was unable to recognize the device. So I was stuck for the moment and had to leave that way until I had more time.
Received a phone call and when I hung up it went to white screen with call graphics at the bottom, missed call, received call, etc. I soft reset the phone and then the Tri-Color screen came up and this is the info:
KAIS130 MFG
SPL-1.0.0lIPof
CPLD
I am assuming this is the first HardSPL that I loaded. So then I preceed to flash via SD and it says that the flash completed and was successful. However when I soft reset the phone goes back to the Tri-Color sceen and does not load the image I just flashed.
Anyone have any ideas how I can get this phone working again? I am open to any and all suggestions.
Thank you in advance
does the bootloader show ruunbh on top?
ok this should be an easy fix! the poster above asked the right question!
lets start from scratch now though ok,
-first download SSPL.KAIS and save it to your memory card.
- Download Which ever hardSPL you would like to use.
- run SSPL.KAIS from SD card and then flash New HardSPL, check to make sure it flashed right by going into bootloader should say what ever SPL you just flashed.
- If that flashed correctly then proceed to flashing the HTC WM6.1 shipped ROM, which can be found on the forum! Make sure its a NON-cooked rom...
- If that flashed correctly then pick which ever custom rom you would like and flash that, make sure that flashed correctly and if so your done
Austinsnyc,
Thanks for the speedy reply. Sorry just a few questions and one statement.
The phone is in the Tri-Color screen state constantly. The only way I can load the bootloader is if I rename a ROM to KAISIMG.nbh. Then is something akin to ROM, radio, etc and when that flashes they will have an OK next to them. Alright with that said a few questions.
Do I have to rename the SSPL.KAIS file, it does not run as is? When loaded on the the card, Tri-Color comes up and then for a brief second is says, Loading.....No Image File.
Do I load both files on the card at the same time and do I have to rename them? i.e. KAISIMG.nbh
Thank you for your help
thesire said:
does the bootloader show ruunbh on top?
Click to expand...
Click to collapse
No it doesn't. I will say KAISIMG.nbh, the ROM I renamed to load. Then is list all the features of that ROM, i.e. OS, SPL, radio. I flash it and it says success but still will not load.
Thank you
culleyps said:
No it doesn't. I will say KAISIMG.nbh, the ROM I renamed to load. Then is list all the features of that ROM, i.e. OS, SPL, radio. I flash it and it says success but still will not load.
Thank you
Click to expand...
Click to collapse
MTTY
cmd>set 16 0
cmd>boot
Can MTTY be run form the SD card?
I didn't clarify so well, I cannot use usb connectivity to the PC. Everyting needs to be done off the SD card.
Thank you
culleyps said:
Can MTTY be run form the SD card?
I didn't clarify so well, I cannot use usb connectivity to the PC. Everyting needs to be done off the SD card.
Thank you
Click to expand...
Click to collapse
okay read more about mtty for clarrification. as long as it says usb when u hook up to computer in bootloader u should be fine. but first read on mtty before running cmds.
thesire said:
okay read more about mtty for clarrification. as long as it says usb when u hook up to computer in bootloader u should be fine. but first read on mtty before running cmds.
Click to expand...
Click to collapse
thesire,
I will research the this more. It does say usb on the phone with plug in otherwise when unplugged it says serial. When plugged in I can't see usb in the drop down in MTTY. I will keep reading.
Btw, it now says RUUNBH in the top right hand corner.
Thanks
culleyps said:
thesire,
I will research the this more. It does say usb on the phone with plug in otherwise when unplugged it says serial. When plugged in I can't see usb in the drop down in MTTY. I will keep reading.
Btw, it now says RUUNBH in the top right hand corner.
Thanks
Click to expand...
Click to collapse
that means you have bad data blocks which can also be cleared using mtty.
I must be very thick, I can't get MTTY to connect. Every time I plug in the USB to my Vista OS pc is says it can't recongize the device and it has malfucntioned. I know the USB is working, it was up until I was having this problem at least.
So I start MTTY and look for USB in the drop down for Port but only COM 1 & 2 show up.
So any other suggestions you or anyone else may have is greatly appreciated.
Thanks for your patience
with Vista you need to use Mtty 5.13 which can be found in the FrankenKaiser radio from hell thread. There is also a guide on how to install the old XP drivers to WindowsMobileDeviceCenter that helps a bunch with USB issues. Also I think you miss understood me the tri-color screen is the Bootloader screen!!!
USERNAME said:
that means you have bad data blocks which can also be cleared using mtty.
Click to expand...
Click to collapse
I don't think it means bad blocks for sure.
Ok. I have read just about everything I can find on MTTY, old XP drivers (which I already have installed) and I still can not get anything to work. When I plug in the phone via usb, pc says it cannot recongize the device and it must have malfunctioned. I have tried MTTY 5.13 numerous times and still cannot get usb to show up and have been unseccessful with all my attempts to connect via a COM port.
Is there any place in NYC, Brooklyn or Queens that I can take this phone too and someone with more experience can fix this for a fee of course? I just and need to get my phone working again.
So I have another question since I have been unable to get anywhere with the dang thing.
I am unable to get my laptop/pc to recognize the phone, I can't even get drives to load. Been searching and reading and still looking for a solution to this issue. If you know where is answer is in this forum could you please point me in the right direction?
Aslo, if someone is willing to spend the time with me to solve this issue get the phone running again, I will be more the happy to donate generously.
I think this can be solve quickly if I could get the time with someone.
For the folks that have replied, I can't thank you enough it has been a great learning experience.
Thanks
Same problem here. Please help!
I am having exactly the same problem. PANIC!
I am a complete noob to all this, but managed to flash Duttys Rom.
(Ruu_Signed_Duttys_WM6.1_Official_5.2.19209_1_58_16_27 [FIX])
I was incredibly pleased with the results.
The phone ran better than ever till this morning. The sound stopped working, I soft reset and now I cant get past the tri-coloured (boot loader ?) screen.
KAIS130
SPL-3.29.Hard
CPLD-8
SERIAL
I cant hard reset, it just goes back to the tri-colour screen.
Help!
If I am not being clear or more info is needed please let me know.
5manarmy said:
I am having exactly the same problem. PANIC!
I am a complete noob to all this, but managed to flash Duttys Rom.
(Ruu_Signed_Duttys_WM6.1_Official_5.2.19209_1_58_16_27 [FIX])
I was incredibly pleased with the results.
The phone ran better than ever till this morning. The sound stopped working, I soft reset and now I cant get past the tri-coloured (boot loader ?) screen.
KAIS130
SPL-3.29.Hard
CPLD-8
SERIAL
I cant hard reset, it just goes back to the tri-colour screen.
Help!
If I am not being clear or more info is needed please let me know.
Click to expand...
Click to collapse
Does it say RUUNBH in the top right corner?
Hi.
All I can see on the screen is as follows.
------------------------------------
KAIS130SPL-3.29.Hard
CPLD-8
Serial
------------------------------------
I have absolutely no idea where to go from here.
Cold sweat....
5manarmy said:
Hi.
All I can see on the screen is as follows.
------------------------------------
KAIS130SPL-3.29.Hard
CPLD-8
Serial
------------------------------------
I have absolutely no idea where to go from here.
Cold sweat....
Click to expand...
Click to collapse
The best thing for you to do is contact GSLEON3 to see if he can help you out.
Thanks for your response.
I somehow seem to have gotten somewhere.
I just repeatedly kept trying to hard re-set, taking the battery out, connecting USB.... and then it hard-reset.
They say the definition of insanity is doing the same thing and expecting different results.
I wonder if you can recommend a stable ROM? I love the speed and battery life of the one I installed but dont like the idea of being between meetings and having a phone in limbo.
Thanks again.
I'm new in the world of flashing cooked ROMs
and i need to do it but i can't
Everytime i try to Flash HARDSPL 3.xx, it stops at the percentage screen and gives me an error on my pc.
And i tried to flash the ROM directly, and same problem.
I'm getting nervous of this stupid mobile, please i need Help.
I read all posts on how to install everything but nothing completed to the end.
bebo833 said:
I'm new in the world of flashing cooked ROMs
and i need to do it but i can't
Everytime i try to Flash HARDSPL 3.xx, it stops at the percentage screen and gives me an error on my pc.
And i tried to flash the ROM directly, and same problem.
I'm getting nervous of this stupid mobile, please i need Help.
I read all posts on how to install everything but nothing completed to the end.
Click to expand...
Click to collapse
you should go here ...
I had a problem when I first did mine. at the tri-color screen my phone never said USB on it and my computer showed an unknown usb device. Here's what worked for me but remember you only need to do this the first time, Once you have HardSPL flashed your phone will work like normal.
after your phone gives you a warning that a program is going to reboot it. You get a tri-color screen. As soon as you see this screen hold the camera and power button and press the reset button, don't disconnect the usb cable.
In other words the program that causes your phone to reboot doesn't allow the usb to work properly but a manual reboot into the SPL using the camera/power button does. I have not tried the "Forced USB" version of HardSPL because this problem goes away once you get HardSPL installed.
This would be better posted in the HardSPL thread.
Flash an official stock ROM, then follow ALL the instructions in the link deepthroat gave you to the T.