Database Info

please help me with qtek S100

hello all,
I got one Qtek S100 phone with rom version :1.03.04ITA.I tried to upgrade it for english rom but upgrade wizard ran for few seconds and stoped the response with phone.
now when i tried to power on the phone its mentioned serial(with cable connected USB 1.0)like that.
now i need a urgent solution for revive my phone .
please help me guys.

Was this your first time upgrading your s100's rom? Have you read the upgrading instructions? When the s100 is plugged to the pc, the upgrade takes some time (maybe even 20 whole minutes). You should not remove it from there. If you had checked the screen carefully while upgrading, the phone was in fact "on" (just the light was turned off) and you should have let it complete the upgrade.
Just try to upgrade the rom once more and be more patient this time.

yes i was stayed till its mentioned that some error on the computer screen.After that only problem occured.
which firmware should i use to flash this qtek S100 version i mentioned.
please let me know that.

You took the wrong tools. Read this to see what you need http://forum.xda-developers.com/viewtopic.php?t=46628
M

jugnustar
faizalg said:
hello all,
I got one Qtek S100 phone with rom version :1.03.04ITA.I tried to upgrade it for english rom but upgrade wizard ran for few seconds and stoped the response with phone.
now when i tried to power on the phone its mentioned serial(with cable connected USB 1.0)like that.
now i need a urgent solution for revive my phone .
please help me guys.
Click to expand...
Click to collapse
hi
where did you got ROM ENGLISH? p.s reply me site

Updating Qtek S200 ROM has cell phone locked in Boot loader

Hi there,
I bought a Qtek S200 and I tried to do a ROM upgrade. I followed the instructions given in the website http://kimpeacocke.blogspot.com/2006/06/how-to-perform-rom-upgrade-on-your-i.html
I got the upgrade from this site at ftp://xda:[email protected]_022021_Dopod_PDAMobizEdition_v101.zip
I followed the procedure given in the website given above. After I upgraded successfully the phone has become locked in the boot loader screen. I have done both soft reset and hard reset. Nothing works. The phone gets locked in the boot loader screen. Need help.
Thanks,
Julian

Try to reflash with Qtek ROM instead...
Why you said that it's locked on the Bootloader screen?
Is it frozen or locked?

Hi Rayan,
I tried flashing with the Qtek ROM. I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there. Nothing else happens. I have sent the device back to the guy from whom I bought it.

I got the same problem as Julian - I tried to upgrade with the mentioned ROM and now my device are stucked at the boot screen :?

Some help here ? I'm in same situation
I have an O2 with Dopod rom, after I instaled some software I must to restart and then my O2 are stucked/frozen on Windows Mobile splash screen
Only if I remove the battery I can stop the pda.
I can't do nothing to make him to start. Some ideea ?
:shock:
Later Edit :
solved with http://forum.xda-developers.com/viewtopic.php?t=49298&sid=35f5c1e9e165997b4634ea0c7700ac76

Same issue here with a O2 Xda Neo with German Rom.
Applied the procedure of the prophet wiki : How to CID unlock and Upgrade your Prophet (SPL 2.09 & 2.15)
After step 6 and a soft rest it is stuck in bootloader and will not do anything else, not even off or hard reset...battey has to be removed in order to shut it off....
Any ideas?
Remind me to find the guy who wrote the wiki page on unlocking CID in Prophet......good job pal......
Aaaaarggghhhh %^*^%*^%*^%*

Problem solved..
Hi everyone,
Good news at last. I sent my Qtek S200 to the guy from whom I bought the phone. He fixed it and now I am a happy man. You can check with him if everything else fails. Email him at E gadget Depot ( [email protected]).
All the best..

i tried to upgrade my QTEK S200 with this RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID.zip it got to 95% and then it gives me nbf file cannot work with your PDA. Please help.

I have this problem too, i know only one exit from this situation - i have flash my s200 with RUU_215737_2157135_023021_QTEK_s200_RUS ROM, now it work fine.
you find it her

bootloader issue
I have the same problem too, If anybody know method to fix this problem please help us.
I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there.
THX in advance for you help
Robert

have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM

Please, the links to the solution does not exists anymore.
I need help!!
Qtek S200 stuck in tri-color screen, all flashing so far still does not make it work..
When doing a hard reset I get format failed.
/Jonas

I have same problem!
Anyone can help?

TJSM said:
I have same problem!
Anyone can help?
Click to expand...
Click to collapse
Go to HMA4's upgrade guide or my thread in my signature...

same problem
i have exactly same problem and i couldnt solve it too.So can someone help us?
Please someone explain completely what should we do.
i can not active sync and waiting on the bootloader screen

bacardilima said:
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Click to expand...
Click to collapse
daelee,
you can get normal state, follow the bolded attention at above quote.after entering the 3 colour screen connect USB and you can load the original WM5 ROM on your device. after that, upgrade to any wm6 by the rules and active sync.

the link is dead on that message..
i went to the that page and the link for solution is dead.

http://forum.xda-developers.com/showthread.php?t=376561
find out is there anything that can help!

Hard Spl White Screen Problem Pls Help!!!

Im Using Imate Jamin (g4) And I Wanted To Upgrade To Wm6.1, While Running The Hard Spl My Phone Turns To White Screen.. And Active Sync Doesnt Recognise My Phone Any More... Pls Help Me Guys..

THere are many posts like this.
Did u do your reading before flashing? Are you using Vista, if so get on a computor running XP, u cannot flash with vista.
Did you unplugg all ur usb devices and any other connection software? Try also other usb ports. I had to try 3 of my 4 before flashing worked for me.
Please read the wiki and search the forums tho, there are many good guides out there like this one attached (apols for zip file, i had saved the web page for use ages ago)
You also dont say what ur IPL/SPL numbers are so its difficult to help, you should list the steps when posting if you need help
Get back if you need more help...

ginbuko said:
Im Using Imate Jamin (g4) And I Wanted To Upgrade To Wm6.1, While Running The Hard Spl My Phone Turns To White Screen.. And Active Sync Doesnt Recognise My Phone Any More... Pls Help Me Guys..
Click to expand...
Click to collapse
Hi, I had similar problem even after repeated tries. What I did to get around it was:
1) Run the HardSPL (from Prophet tools or from RUU).
2) Check "I understand the caution..." and click next to get to 2nd screen (see attachment) on RUU where it gives you the 4 things to check before proceeding (here your Prophet must be entering the white screen).
3) Leave the RUU on the 2nd screen on the computer and disconnect Prophet after white screen gets stuck and activesync disconnects).
4) Reboot Prophet.
5) Reconnect Prophet and wait for activesync connection to be established.
6) Now on the computer check "I completed the steps indicated above" and click on next.
Hopefully this should go ahead and HardSPPL your Prophet.
Do let us know if this worked.

possible solution for ya
Code:
ginbuko said:
Im Using Imate Jamin (g4) And I Wanted To Upgrade To Wm6.1, While Running The Hard Spl My Phone Turns To White Screen.. And Active Sync Doesnt Recognise My Phone Any More... Pls Help Me Guys..
Click to expand...
Click to collapse
Hey,same problem here...but you probably got rid of the prophet already...well hope it helps someone else
thank God i had surfed to other sites and found this HARD SPL utility.
Its in "wm6 Update_Package" ...might as well be from here..
(dont know who made it-i`ve been downloading so much stuff lately from the web no offence )
maan...how do I add an attacment here?
ahah-here it is..
hey...what`s up with this...cant upload...its under 8mb,why is it bugging me with "upload of file failed"?
ok...this means war..
anyway here is the link http://rapidshare.com/files/233302800/HardSPL_G3_and_G4.rar.zip.html

ginbuko said:
Im Using Imate Jamin (g4) And I Wanted To Upgrade To Wm6.1, While Running The Hard Spl My Phone Turns To White Screen.. And Active Sync Doesnt Recognise My Phone Any More... Pls Help Me Guys..
Click to expand...
Click to collapse
pinoy ka gin???
text mko kung malapit ka lang sa manila.. help kita...
09085524216

Hi
where i can download hardspl for g4?

"catch-22" Phone don't want let me flash a new ROM, PLEASE HELP!

Hi,
I'm almost broken down :'(
since days I'm trying everything to update the rom of my smartphone with the following operation system "XP and Vista".
I've got a Xda Touch diamond, but Vista says I've got a Touch Diamond P3700. Now let me tell you the catch-22:
I'm connecting the phone via usb cable to the pc(any usb-hub on the back of the pc)
Vista and Xp says "connected". Now I'm running RomUpdateUtility.exe. In the same folder
is the new rom called "DIAMIMG.NBH"
Now I'M clicking "Next" and again "Next". Now he says"verifing the information on your PDA Phone.. Please wait..
After that he says Current Information about you PDA Phone: Image version: 1.93.407.1
So now I'm clicking "update" the new Image version is 1.00.000.0
(If I use another Update Utility he says to Image Version 2.03.207.2)
Clicking "Next" and then again "Next" My Phone turns black and then the phone displays the three-color mode
and below the "serial" change to "usb" and a few
seconds later the phone shows a bar of 0% and on WinXP the bar also shows 0%.
Suddenly the connection is off. And a few minutes later the update Utility(PC) says EROOR(262) UPDATE ERROR.
I even disbaled the standby and hibernation modes on the PC. And I even tried flashing from Internal Storage!
ABsolutly futile! The three-color mode displays DIAM300, SPL-1.30.OliNex, MicroP-Diam (Led) v11,
Psoc_Diam STAGE_PVT v=x32
Is may Phone locked for new roms?
Please HELP ME before I'm going sick ´:__(
Best regards
Colbad

Welcome to forums
Hope this link helps
http://wiki.xda-developers.com/index.php?pagename=HTC_Diamond
Good luck,

nothing helps. I give it up!
I'll get me a new phone.

slow down lol,
dont rush out and get a new phone just yet.... all flashing problems are actually quite simple, you just need to be methodical and patient
Firstly, i always flash with XP, call me old fashioned but its what ive always done lol.
in the past when ive had 262 errors (whilst flashing my touch cruise RIP) the radio i had installed at the time prevented further flashes.
What you havent said is what your current rom is and what rom you are trying to flash.

Hi again
I bought me a new one!
my new htc touch diamond makes me also sick.
If I download from the HTC page the new software rom
there's no problem updating my Smartphone to 100%.
But if I try to use any foreign rom for updating he freezes by 0%.
What is that?
I can't use any foreign rom from other peoples,
I'm absolutly helpless to this issue.
Please help me anybody :=)
Best regards
COLbad

colbad said:
Hi again
I bought me a new one!
my new htc touch diamond makes me also sick.
If I download from the HTC page the new software rom
there's no problem updating my Smartphone to 100%.
But if I try to use any foreign rom for updating he freezes by 0%.
What is that?
I can't use any foreign rom from other peoples,
I'm absolutly helpless to this issue.
Please help me anybody :=)
Best regards
COLbad
Click to expand...
Click to collapse
Colbad,
Please tell me you have read the wiki or at least the stickys on how to flash with either hardspl or uspl etc??
If not ur gonna end up with a fancy looking brick.... what have you tried so far and from where?

sorry for bothering you.
I solved the issue finally
Now everythings fine.

I-mate jama 201 Stuck

Hi mates i have imate jama 201.....
stuck on after few moments

saajith said:
Hi mates i have imate jama 201.....
stuck on after few moments
Click to expand...
Click to collapse
What do you mean? Does it sometimes stuck?

white screen
i wrongly flashed the imate jama201 with jama_8050_wwe_rus_wm6 bu sd card method.
phone was not flashed only boolder or something was came at the time of flashing after that its white light only.
and i am not able to find any sutable rom for my phone please help me to recover my phone or give any rom link for the same

ayeah said:
i wrongly flashed the imate jama201 with jama_8050_wwe_rus_wm6 bu sd card method.
phone was not flashed only boolder or something was came at the time of flashing after that its white light only.
and i am not able to find any sutable rom for my phone please help me to recover my phone or give any rom link for the same
Click to expand...
Click to collapse
Doesn't this phone has a specific forum http://forum.xda-developers.com/forumdisplay.php?f=245. If this is the one, you should go there and have a in-depth reading to see how to solve this problem

i mate jama 201 need help for unlock
i have i mate jama 201 with out sim it is asking on display (this device is locked. enter your device password and click unlock.to make an emerganse call click menu)
pls need some solution for this problem