Related
May 24th, 2008
FrankenKaiser SPL Loader
This is a fast application image downloader which can download e.g. spl or android to the phone when the phone is in dload mode. This can for example be useful for developers to test a SPL from another device w/o the need to flash them
======================================================
DISCLAIMER: This method involves erasing SPL & OS and requires correct data entry by the user. I will not take any responsibility for any malfunctions and or damages caused by using this method and software.
======================================================
Prerequisites:
- a *security unlocked* HTC MSM7x00 device
- QC diag drivers installed (e.g. MotoQ)
This was tested with a Kaiser, Niki and Wings
Steps are:
1 power down
2 hold green send key and power on, the phone will enter radio bootloader (oemsbl)
3 connect with MTTY (COMn) and type "dload" to put phone in dload mode
4 close MTTY, reconnect USB, run my new downloader in a CMD box, e.g. "./FrankenKaiser-SPL-Loader.exe /dev/com4 SPL1.56-KAIS-unbricker.nb (substitute com4 by the com port of your qc diag driver)
5 hold send key and press soft reset with stylus (on phones like Nike this is not possible, in that case you must add "setboot 1" to step 3 before typing "dload" and in step 7 add "setboot 0" before typing "dload")
6 connect with MTTY (COMn) and type "mw 901708 1 e1a00000"
7 type "cego" (press and hold camera to enter tricolor bootloader mode)
Have fun!
may i be one of the first to say Thank you.
jumpspl, supercid and security unlocker, frankenkaiser .. man you are owesome.
A truly gifted individual and thank you for all your hardwork.
Thanks, Jockyw2000, your work really rocks, but...
OEMSPL did not work for me (HTC Wings)
Ive hold down the green button and tapped the PowerButton=>Boots normal.
Offtopic;
My Question is; Is it possible to "Switch" the GPIO 0x5c (Kaiser SimDoor) from 0 to 1 manually?
Because i want to "port" a KaiserRom over to my Wings, but ive getting trouble with this annoying "Sim Door Open, please close it.Phone shuts down in 10 seconds..." warning.
arpy said:
Thanks, Jockyw2000, your work really rocks, but...
OEMSPL did not work for me (HTC Wings)
Ive hold down the green button and tapped the PowerButton=>Boots normal.
Click to expand...
Click to collapse
Your Wings is not security unlocked, so you can't enter oemsbl that way.
Offtopic;
My Question is; Is it possible to "Switch" the GPIO 0x5c (Kaiser SimDoor) from 0 to 1 manually?
Because i want to "port" a KaiserRom over to my Wings, but ive getting trouble with this annoying "Sim Door Open, please close it.Phone shuts down in 10 seconds..." warning.
Click to expand...
Click to collapse
Afaik that's possible.
Security Unlocked?!?
Ähh...ok...isnt enought to flash your HardSPL?
...but youll give me some hope...now i digg deeper into this phantastic Forum...
Just a quick question Jocky....
How does this differ from using MTTY to upload SPL to our Kaiser?
kyphur said:
How does this differ from using MTTY to upload SPL to our Kaiser?
Click to expand...
Click to collapse
How do you use MTTY to upload a SPL then ?
jockyw2001 said:
How do you use MTTY to upload a SPL then ?
Click to expand...
Click to collapse
I'm asking with all due respect. I haven't done it. To be honest I haven't flashed anything with MTTY since I had my Hermes last year but I was under the impression that we could.
If we can't then you have answered my question as the difference is exactly that!
In the quest for knowledge we all sometimes ask apparently dumb questions...
So with this thing I can make my deviece look as a MSM7500. To boot up HaReT all the time???
kyphur said:
I'm asking with all due respect. I haven't done it. To be honest I haven't flashed anything with MTTY since I had my Hermes last year but I was under the impression that we could.
If we can't then you have answered my question as the difference is exactly that!
In the quest for knowledge we all sometimes ask apparently dumb questions...
Click to expand...
Click to collapse
obviously you can, the RUU uses mtty commands to download the images.
When I run FrankenKaiser-SPL-Loader.exe , WindowsXP closed DOS window with error.
What is wrong ?
WBR !
Sorry, duble.
"mw 901708 1 e1a00000"
what's at address 901708 and why change it to E1 A0?
ma kaiser dead or not please help will donate with paypal 50pounds if you can help
wait ....to resolve this .
gsmhackerns said:
I use hard spl and install radio to unlock my htc tytn bat after this i flash with this rom :RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27.04.15_Test
My phone complete all proces 100% bat after this can not boot or charge no ligh no bootloader as i can see now it have only radio bootloader (oemsbl) and i found and install driver and see in device menager com ports quacom diagnostic interface 6000 and qualcom nmea device...Can you help me to unbrick my kaiser with frankenkaiser spl loader i will donate with paypal you please...pm fuull instuction or can you create for me exe file with all .thanks.wait you.
Click to expand...
Click to collapse
Did you security unlock your device before this happened?
Ta
Dave
DaveShaw said:
Did you security unlock your device before this happened?
Ta
Dave
Click to expand...
Click to collapse
i install hard spl unlock device bat after flash complete 100% my phone always go in oemspl can not go in normal bootloader or power on.
Since it doesnt seem as though you unlocked the phone, just download an oem rom/radio combo for the phone from the operator it belongs on ( IE , if it is an ATT TILT, download from HTC the latest rom off their website JUST for the att tilt )
This should fix you up
DaveShaw said:
Did you security unlock your device before this happened?
Ta
Dave
Click to expand...
Click to collapse
Dave i have same prob...device allready unlocked before flash... no power on, no bootloader mode... on pc recognized like diagnostic.... what can i do?
Frankenkaiser error
I managed to brick my device real good. When I start the device, holding down green send, and run mtty to run the dload command, I get Invalid command : dload. Im in deeper than I bargained for. Whats next?
the0ne.john said:
I managed to brick my device real good. When I start the device, holding down green send, and run mtty to run the dload command, I get Invalid command : dload. Im in deeper than I bargained for. Whats next?
Click to expand...
Click to collapse
What did you do? task 2a?
Are you security unlocked? What SPL do you have?
Thanks
Dave
I have an ex-Vodafone, sim unlocked HTC touch diamond and it won't turn on. All I can do is bring it into the tri-colour screen/bootloader. When plugged into my computer the phone screen goes from serial to usb, but thats as far as it gets. Communication with activesync is no longer possible. I have no idea what to try now, I've gone as far as my non-technical mind will go ! help
I'm in the UK. Phone info;
Duttys V2.7 RC2 WWE - 27/10/08
Radio 1.08.25.08
P3700
Bootloader screen reads;
DIAM 100 MFG 64M
SPL 1.40 Olinex
MicroP- Diam (LED) v11
PSOC - Diam STAGE_PVT v0x30
Welcome to forums
Please have a deep read here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Diamond
You´ll find all needed to do a succesfull reflash.
Good luck,
no comms with activesync
thanks for the link. have read the info on flashing my device but my phone no longer communicates with activesync. Is it bricked ? Phone won't go beyond initial 'vodafone' startup screen. i don't know what to do now.
which os in computer do you use ??? if in tri-color boot loader, pc only recognized the HTC driver device, but Activesync won't show the connect. You understand what i mean? Go Flash yourself your device with successfully, I will pretty sure that your device doesn't brick.
yes correct you can run the RUU wrapper while the phone is in the boot loader and itll still flash the rom
i use windows xp home sp2, i don't understand the flash process and can't get further than the tri-colour screen. I think i need a very simple step by step walkthrough if I'm to get any further !
ok
down load the rom of your choice and exract it
in the folder there should be a file called ruu_signed.nbh and a exe file called RUU wrapper or something like that if it doesnt come with the RUU wrapper it should be able to be downloaded from a stickied thread at the top of the diamond rom forum
then u need to connect ur phone to the pc while its in the boot screen the click on the ruu wrapper in the file on the pc and it should install on ur phone
hi, i downloaded the ruu, then connect my phone in boot screen, start the install, it asks me to make an activesync connection. activesync no longer finds my phone so no connection is made. i got this close, what now ? thanks for the help !
Done it finally
after many dime bar moments and weeks of annoyance the touch diamond finally came back to life. expecting this phone to actually work as advertised turned out to be a bridge too far. cheers for the help.
Hi ! I have a problem with my Kaiser ! The screen is black, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays black ! Is there a way to make my kaiser working ? (Sorry for my english)
Remove battery and then press power button 30 seconds or more.
Worked for me.
Assface said:
Remove battery and then press power button 30 seconds or more.
Worked for me.
Click to expand...
Click to collapse
it doesnt work ! I think there is a problem with spl , because this problem appears after unsuccessful hard spl installing ! I don know how to fix this
IP13 said:
Hi ! I have a problem with my Kaiser ! The screen is blank, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays blank ! Is there a way to make my kaiser working ? (Sorry for my english)
Click to expand...
Click to collapse
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
krouth said:
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
Click to expand...
Click to collapse
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
IP13 said:
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
Click to expand...
Click to collapse
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
krouth said:
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
Click to expand...
Click to collapse
Active sync doesnt recognize my Kaiser!
IP13 said:
Active sync doesnt recognize my Kaiser!
Click to expand...
Click to collapse
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
krouth said:
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
Click to expand...
Click to collapse
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
krouth said:
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
Click to expand...
Click to collapse
I cant install this rom because it shows me an error : "ERROR [260] CONNECTION
The Update Utillity cannot connect your PDA Phone . Please check that your USB cradle/cable is connected properly between the PC and your PDA phone .
Chech the following :
1.The PDA Phone is connected to the USB cradle/cable.
2.The USB cradle/cable is connected to the PC "
I have allready checked the cable (it works with my other PDA)
delower10 said:
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
Click to expand...
Click to collapse
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
IP13 said:
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
Click to expand...
Click to collapse
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
krouth said:
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
Click to expand...
Click to collapse
Yes ! I also get the blank screen after following all this steps !
IP13 said:
Yes ! I also get the blank screen after following all this steps !
Click to expand...
Click to collapse
I am not sure.... I have done some searching and ran across this thread:
http://forum.xda-developers.com/showthread.php?t=423486
It has numerous posts about problems people have experienced flashing - maybe you might get some insight there - or at least post your question there where more people might be monitoring the thread. Good luck!
Please take your issue to the right place, better than open a new thread, I sugest
http://forum.xda-developers.com/showthread.php?t=433835
Your situation should be taken by the right guys, not just gessing if this or that might solve the situation, male a post there
Also have a look at the sticky on the top, try to get Dave Shaw help
THx I will try to ask there ....
Fanning the flames.
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
tyler51773 said:
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
Click to expand...
Click to collapse
Thx man , appreciate this !!
This mode was accidentally entered when I'm trying to boot my htc hd7 and press camera button together with volume up (around 20sec while the phone booting). For your information, my htc hd7 having problem with zune application and my device manager recognize it as unknown devices (yellow exclamation mark).
It was caused when I've sideloading USBModeSwitch.xap and change from ZUNE to DIAG mode. After the phone restarting, the apps has been revoke then i've no chances to install the apps again to fix it back to ZUNE mode.
Now the phone can operate as usual but cannot recognize by zune (yellow exlamation mark in device manager in PC).
The good news is, the phone had recognized by pc when entering this mode. and the devices manager detect the phone under Portable Devices -> Schubert. Can we sideloading apps using this mode? If yes... it was a good news for those having the same problem with me. But the question is.. HOW.
Note: After the incident, I already flash the phone. but still unable to be detected by ZUNE Desktop in normal state. it can operate, can install from market place as usual but cannot sync with zune desktop. Can somebody help me on this? Sorry for my English. You may refer with my attachment for the images and the XAP application.
Note 2: Never try the USBModeSwitch.xap if your phone is not fully unlock or will facing the same problem with me. hope someone can fix this issue. because lot of friends are stuck in this doom.
same problem here....
an hd7 too...
First, are your phones unlocked? I assume they are. Otherwise you wouldn't be able to deploy this USB-whatever.xap.
You may try deploying smth after running WPConnect (Phone has to be connected already). This small consoleapp does some funny stuff with the phone/PC connection. So maybe your devices will be recognized this way.
Best you start WPConnect from commandline, to have a look at the output, which should be smth like "[Devicename] successfuly connected..." or such.
C~
tried it, doesn't help
the phone is not unlocked anymore... that is the problem in my case ;-)
but i was able to install the HTC Diagnostic Drivers...
but i dont know if i can use it to disable Diag-Mode...
And you are not able to re-unlock your phone (via official or Chevron)? Have you tried to unlock after connecting - closing Zune - running WPConnect?
This is just a mere guess, but hey, who knows it maybe work
we cannot lock our devices as neither zune nor WPConnect realize that the phone is connected (because of it is in Diagnostic-Mode)
but thanks for your reply ;-)
Oberoth said:
we cannot lock our devices as neither zune nor WPConnect realize that the phone is connected (because of it is in Diagnostic-Mode)
but thanks for your reply ;-)
Click to expand...
Click to collapse
Yup that's true. I try to used ansar ROM, flash it, but nothing change. I wonder if we can custom a rom and implement the extract file of USBModeswitch.xap to the rom. so that the phone will boot with usbmodeswitch installed in it, using this step, we're able to switch the mode from diag back to zune.
This the final technique might can help for now. For the ROM, i can only break/extract until I've got the 2 OS file:- 2_os.nb.extra (±2.4MB) and the other one is 2_os.nb.payload (±181MB). Ok, until then, I was stuck. if not... we can extract the XAP directly to the OS folder, then repacking back the ROM. the 2_os.nb.payload file was unable to extract to bin file. Error shown:- "no boot partition". Maybe I'm using the old WinMo tools to extract it.
ahhh.... gosh... stuck in this step. any help and guide will be much appreciated.
AzmanIshak said:
Yup that's true. I try to used ansar ROM, flash it, but nothing change. I wonder if we can custom a rom and implement the extract file of USBModeswitch.xap to the rom. so that the phone will boot with usbmodeswitch installed in it, using this step, we're able to switch the mode from diag back to zune.
This the final technique might can help for now. For the ROM, i can only break/extract until I've got the 2 OS file:- 2_os.nb.extra (±2.4MB) and the other one is 2_os.nb.payload (±181MB). Ok, until then, I was stuck. if not... we can extract the XAP directly to the OS folder, then repacking back the ROM. the 2_os.nb.payload file was unable to extract to bin file. Error shown:- "no boot partition". Maybe I'm using the old WinMo tools to extract it.
ahhh.... gosh... stuck in this step. any help and guide will be much appreciated.
Click to expand...
Click to collapse
Hi,
from your writing i can read that you have the needed knowledge to make this thing...
so how long do you think will it take to get the two files...
and if you get these files, how can we flash that ROM without HSPL or SSPL?
thanks for your answer ;-)
our problem is... there's still no kitchen for WP7 (temporary). So.. we have to wait Da_G or Ansar.Ath.Gr work. they might have some tools that can help us. I knew.. lot of our friend already stuck in this mode as well. So... there's no sync with zune for us... no music transfer via usb.. and we have to forget all the thing that we can do using the USB cable except for charging it. lol~ how sick...
yeah...
i can only listen to radio in the morning when i drive to school...
i hate the most of the breakfast-shows
i have another idea instead of waiting for an C-ROM...
but that is only possible with a clean, Chevron-Unlocked and USB-Switch installed WP7 phone...
so nothing personally...
and we need to wait for the update...
the whole clean system would be backed up and could be used for our WP7 devices to get the USBSwitch-App onto our phone (holding camera-key when starting to install backup)
would be great if there is anybody who makes it...
hi
ask the autor of this http://forum.xda-developers.com/showthread.php?t=922000
maybe he can help ,his tool use usbmodeswitch.
im active in his thread too, but he didn't answer at all...
I have actally done this myself sadly the only option I had was to sync all my contacts with Windowslive and reset the HD7 by holding both volume keys while powering it on from a cold boot.
AzmanIshak said:
This mode was accidentally entered when I'm trying to boot my htc hd7 and press camera button together with volume up (around 20sec while the phone booting). For your information, my htc hd7 having problem with zune application and my device manager recognize it as unknown devices (yellow exclamation mark).
It was caused when I've sideloading USBModeSwitch.xap and change from ZUNE to DIAG mode. After the phone restarting, the apps has been revoke then i've no chances to install the apps again to fix it back to ZUNE mode.
Now the phone can operate as usual but cannot recognize by zune (yellow exlamation mark in device manager in PC).
The good news is, the phone had recognized by pc when entering this mode. and the devices manager detect the phone under Portable Devices -> Schubert. Can we sideloading apps using this mode? If yes... it was a good news for those having the same problem with me. But the question is.. HOW.
Note: After the incident, I already flash the phone. but still unable to be detected by ZUNE Desktop in normal state. it can operate, can install from market place as usual but cannot sync with zune desktop. Can somebody help me on this? Sorry for my English. You may refer with my attachment for the images and the XAP application.
Note 2: Never try the USBModeSwitch.xap if your phone is not fully unlock or will facing the same problem with me. hope someone can fix this issue. because lot of friends are stuck in this doom.
Click to expand...
Click to collapse
can you tell me what rom was on the phone and what rom you flashed After you F*****up your phone ?
I want to know what Radio was on it , I think that tool does something with the radio rom on the phone , it could help the flash an older rom using a goldcard with an older radiorom in it.
edit:
maybe it is the spl , try to flash a rom with a lower/higher spl number.
ceesheim said:
can you tell me what rom was on the phone and what rom you flashed After you F*****up your phone ?
I want to know what Radio was on it , I think that tool does something with the radio rom on the phone , it could help the flash an older rom using a goldcard with an older radiorom in it.
edit:
maybe it is the spl , try to flash a rom with a lower/higher spl number.
Click to expand...
Click to collapse
Hi Ceesheim, thanks for reply. I'm not remember my preveous ROM, by the way
currently only RUU_Schubert_hTC_Asia_WWE_1.23.707.01_Radio_5.51.09.06a_22.30.50.09U_Signed_by_ansar that can be flash to my phone.
AzmanIshak said:
Hi Ceesheim, thanks for reply. I'm not remember my preveous ROM, by the way
currently only RUU_Schubert_hTC_Asia_WWE_1.23.707.01_Radio_5.51.09.06a_22.30.50.09U_Signed_by_ansar that can be flash to my phone.
Click to expand...
Click to collapse
thats a modded rom (don't use it)
try this one :
http://forum.xda-developers.com/showthread.php?t=853945
Hi
i think the best way to fix your problem is this rom.
http://forum.xda-developers.com/showthread.php?t=948497
this one contain developer tools & can help you with usb problem.
send me a pm after install it an maybe we can fix this.
xboxmod said:
Hi
i think the best way to fix your problem is this rom.
http://forum.xda-developers.com/showthread.php?t=948497
this one contain developer tools & can help you with usb problem.
send me a pm after install it an maybe we can fix this.
Click to expand...
Click to collapse
ok... will test it now. thanks!
I'll report to you after complete. thanks again~
xboxmod said:
Hi
i think the best way to fix your problem is this rom.
http://forum.xda-developers.com/showthread.php?t=948497
this one contain developer tools & can help you with usb problem.
send me a pm after install it an maybe we can fix this.
Click to expand...
Click to collapse
I already download and install to my PC. but cannot flash to my phone.
Currently the only ROM that my HD7 can flash is with this number: 1.23.707.01
Make a goldcard and then flash it
Sent from my HD7 T9292 using Board Express
This is my first time asking for help directly here, I always find the answers in the other threads solved, but this time I can not find an answer.
I have a alcatel one touch 5020t evolve its a MTK6575 (t-mobile but is used in el salvador), I used to MTKDroidTools to install CWM Revocovery, I did back up with the same program but apparently did not because i look and i cant find anything in the back up folder, only left some files called:
ALCATEL-ONE-TOUCH-5020T_130818__boot_patched_140129-175612.img
ALCATEL-ONE-TOUCH-5020T_130818__recovery_140129-175612.img
in the folder called recovery.
Now the phone on, the startup screen and then turns off, I can enter a menu by pressing on + vol +, where it says enter recovery mode or normal mode, before they tried to install cwm I could go in and delete everything from there, now I get the menu of recovery mode and normal mode but since does not enter recovery mode, got it turns off, like when entering the normal mode.
I tried to flash with sp flash tool but I get an authentication error that is on the img
The pc recognizes my phone, makes the sound when you connect something, now if we go to Device Manager, a device called first appears:
MTK USB Port
After that is disconnected and then a new one appears called :
Media Tek Preloader USB VCOM Port
But there ir a problem, then this becomes a repetitive one disconnects and connects the other, but only when I connect the phone without battery only stays in:
MTK USB Port.
Help what can i do to revive my phone ???????????????
you found any solution i have the same problem ?
:/
harold99 said:
you found any solution i have the same problem ?
Click to expand...
Click to collapse
Sorry, but i could not solve yet, nobody helps me
So were you able to flash cwm to the device? there are several threads requesting a custom recovery for this device and either way could you upload those first two .img files I may be able to use them to try to recover my device
*** Okay so the problem is that the boot loader on this device is locked and for the time being a custom recovery is not possible. I still have access to the recovery on my device so if I could find a way to build an update file from the source code or an official firmware update I could fix mine. Yours may be too far gone. sorry.
any luck with a solution? How close to one have you got to...
ipeedalil said:
*** Okay so the problem is that the boot loader on this device is locked and for the time being a custom recovery is not possible.
Click to expand...
Click to collapse
A friendly warning: Don't just mess around with the Bootloader, that's one delicate piece of software, try to find how to unlock it first, then we can talk of changing the recovery. For rooting purposes I can attest that you can safely root it using the OneClickRoot solutions around the net. I used some chinese root and it worked like a charm.
Soft Bricked 5020T
carlitox2301 said:
This is my first time asking for help directly here, I always find the answers in the other threads solved, but this time I can not find an answer.
I have a alcatel one touch 5020t evolve its a MTK6575 (t-mobile but is used in el salvador), I used to MTKDroidTools to install CWM Revocovery, I did back up with the same program but apparently did not because i look and i cant find anything in the back up folder, only left some files called:
ALCATEL-ONE-TOUCH-5020T_130818__boot_patched_140129-175612.img
ALCATEL-ONE-TOUCH-5020T_130818__recovery_140129-175612.img
in the folder called recovery.
Now the phone on, the startup screen and then turns off, I can enter a menu by pressing on + vol +, where it says enter recovery mode or normal mode, before they tried to install cwm I could go in and delete everything from there, now I get the menu of recovery mode and normal mode but since does not enter recovery mode, got it turns off, like when entering the normal mode.
I tried to flash with sp flash tool but I get an authentication error that is on the img
The pc recognizes my phone, makes the sound when you connect something, now if we go to Device Manager, a device called first appears:
MTK USB Port
After that is disconnected and then a new one appears called :
Media Tek Preloader USB VCOM Port
But there ir a problem, then this becomes a repetitive one disconnects and connects the other, but only when I connect the phone without battery only stays in:
MTK USB Port.
Help what can i do to revive my phone ???????????????
Click to expand...
Click to collapse
I have had a OT-5020T with all the same symptoms as you describe. After much research and diagnosis here is what I have learned and know to be true.
You have soft bricked your phone. For this phone it results in the boot loop you described. At present a Custom Recovery that works is not available for this phone and any attempt to flash an existing one results in a soft brick. There are apps that will flash a Custom Recovery while the phone is one but once you reboot ... !!! Bricked!! This is because ...
a) the memory mapping for this phone is different that other OT-5020 models, so the Custom Recovery placement and indexing is wrong when flashed, causing the boot-loop, and inability for Custom Recovery to load,
and ,
b) the bootloader is locked for the 5020T (different story for other OT 5020 models), and no one has found a way around it yet. Trying to flash back stock firmware for the OT-5020T requires it to be unlocked.
One Touch Update 2.8.0 doesn't seem to want to work one the phone has been altered in this way. SPtools won't work because you need an accurate OT-5020T scatter file (memory map) ,and certification file (bootloader unlocker) to flash any image. In addition to all this the phone doesn't maintain a steady usb connection long enough to allow use of android tools adb and fastboot commands although it does can stay connected in a different mode.
What I have used to restore my phones firmware is a package from Furious Gold that allows the phone to be flashed to factory firmware. I have used it successfully, so I can confirm that the phone wasn't a permanent brick.
Alcatel 5020t T-Mobile plis help flshe file
please am in need of alcatel 5020w firmware, please if someone is having it or having that same phone and want to read the firmware for me my email is [email protected]
thanks