All,
Somehow my bootloader got trashed while swapping memory cards and I'd like to easiest fix to get it going again. (At Tri-Color screen) If I plug it in and run RUU_Kaiser_Cingular_WWE.exe (I'm running nonbloat Tilt rom) it'll start the upgrade, stop at about 1%, but the phone will boot and everything is there. So I'm just looking for a quick way to make it stick so I don't have to do that anymore..
I'll play with cooked ROMs soon, everything is working GREAT for the time being and I don't wanna reinstall!
Thanks all!
-RT
Doesn't sound like you have HardSPL installed but this should fix your problem (at least your issue sounds very similar) ... after you get it fixed you should consider installing HardSPL.
Credit to pof for the instructions below which were part of his now dead SSPL thread for Kaiser:
For those of you had the phone stuck in bootloader mode after flash with SSPL stopping at 16%, follow these instructions to unbrick your phone:
1. Download mtty.exe
2. Disable activesync (connection settings -> uncheck "allow usb connections")
3. Connect your Kaiser to PC using USB cable.
4. Open mtty, select USB port and click OK.
5. Hit ENTER twice, you should see the "Cmd>" prompt.
6. Type the command "boot", you should see something like this:
Code:
Cmd> boot
InitDisplay: Display_Chip=1
No card inserted
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
After that device should boot WM6 again, you can now re-enable USB connections in activesync and flash HardSPL
Click to expand...
Click to collapse
Good Luck
Ahhh!
I didn't find it in the Kaiser forum, but in the Hermes wiki!
Seems that I just had to connect via mtty (to USB, not a COM port! ) then just issue a: set 14 0
Then did a soft reset and all was well!
Back in business!
Now, maybe I'll start playing with some ROMS!
Thanks again!
-RT
hello i have the same problem after i tried to sim unlock my mda vario iii i tried to do what you proposed but didn't work this is what i get when i tried to boot from mtty
Fill RSVD information for block 288 to 309
TAG NOT FOUND !!! NOT CLEAR STORAGE !!!
No card inserted
OEMIPLInit clear 10MB ext RAM
OEMGetUpdateMode
FMD_ReadSector+, bad block no=0x15440, status:0x0
FMD_ReadSector+, bad block no=0x15440, status:0x0
FMD_ReadSector+, bad block no=0x15440, status:0x0
IPLMSG:0x2:ERROR: Failed to open storage partition.
i would apreciate if you can help me
Stuck in Bootloader
Hi everyone,
I tried using MTTY.exe on a XP machine. The option for USB shows up but when i type the command "boot" i get command error. Please help!
KAIS130
SPL-1.93.0000
CPLD-8
on the right top corner the tri-color screen displays RUUNBH
I tried HARD-SPL / gets stuck on 0% and the RUU goes into recovery mode later. Tried stock ROM (Invalid ID).
eddiesantiago said:
Hi everyone,
I tried using MTTY.exe on a XP machine. The option for USB shows up but when i type the command "boot" i get command error. Please help!
KAIS130
SPL-1.93.0000
CPLD-8
on the right top corner the tri-color screen displays RUUNBH
I tried HARD-SPL / gets stuck on 0% and the RUU goes into recovery mode later. Tried stock ROM (Invalid ID).
Click to expand...
Click to collapse
should've read further. You'd of seen my post on Different SPL's & their different command capabilities.
For 1.93 SPL you can issue cmd>task 8
You need to install hardSPL once you get it going, because you DON'T have it know.
GSLEON3 said:
should've read further. You'd of seen my post on Different SPL's & their different command capabilities.
For 1.93 SPL you can issue cmd>task 8
You need to install hardSPL once you get it going, because you DON'T have it know.
Click to expand...
Click to collapse
Thanks for your response GSLEON3
I followed your instructions and used the Task 8 command for the 1.93 SPL
The device turn off and comes back to the same Tri - color screen with RUUNBH on top right. Tried flashing Hard-SPL stuck on 0%. Please help
Anything you found eddiesantiago ?
Hi eddiesantiago,
did you find any solution to your problem, i have a similar issue.
My Tilt Shows :
KAIS1*0
SPL-1.93.0000
CPLD-8
on the right top corner the tri-color screen displays RUUNBH
Please reply if you got it fixed.
TIA,
Dhaval.
same issue
My tilt shows the same info here, is this normal? I need to verify this before I send my TILT back to ATT...
Thanks
Dear all,
got a problem with flashing my TyTN II which might? be related to the
"brand new" version?
here is what happened so far:
we bought several German TyTN II pro and
some of them need to be convert to english rom
Version:
Radio: 1.27.12.32
HardSPL did not install (White Screen) so I went for JumpSPL. Software installed with no problem, "USB" appeared on screen, unplugged and replugged the cable
The TyTN Display is three-colored,
USB connected direct to PC,
AvtiveSync stopped
starting flash-hardSPL\KaiserCustomRUU.exe
starts up,
some "caution" messages read and understood,
TyTN connected,
battery charged,
Software says:
"Verifying the information on your PDA Phone... please wait..."
"Current information about your PDA Phone:
Image Version: [* this part is empty *]
Select from below:
[Update] Update the current ROM version.
KLICK on Update:
From: Image Version [* again no information *]
To: Image Version: HardSPL-kaiser
klick 'Next' to proceed
*Warning message*
KLICK on Next:
Updating the ROM image on your PDA Phone
Please do not remove the USB connection from the PDA Phone or launch
any program during the update process:
PDA Screen goes blank, with progress indicator frozen to "0%"
*STUCK at 0%
PC says: ERROR [262]: Update error, The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the errors .....
After recover, I once again end up with my three-colored-screen
KAIS130
SPL-1.93.0000
CPLD-8
I am able to connect via mtty.exe,
info 0 shows
Model ID: KAIS13000
HW Board ID:31,PVT1
info 2 shows
HTCSHTC__102Ã;¿HTCE
Having read most of the threads here i continued using mtty with
Cmd> boot
Command error!!!
Cmd> task 8
The pda boots again to my beloved three-colored-screen
Any escape from this? Or am I damned stupid ....
Cheers,
Martin
The
Try once more the boot command in MTTY and, if it again enters bootloader, once more. Usually it must be done two times.
no way, as "boot" only says "Command error" a million times ...
Exactly the same thing happened to me Everyone here shouts about flashing HardSPL first (and then it's "impossible to brick your phone"). Unfortunately, people rarely mention that the phone can be bricked whilst trying to flash HardSPL!
With mine, I did initially receive an error when using the 'boot' command, however when I did the following, it worked:
- uncheck 'allow usb connections' in activesync
- get the phone into the tri-color screen and plug the usb cable in
- start mtty, select usb
- issue the 'boot' command (without ANY other commands being issued before it)
Does the tri-color screen say RUUNBH in the top corner? Apparently, some have recovered their phones by flashing a ROM from their original vendor (e.g. if you got yours from HTC, try the base HTC ROM). This never worked for me, I just got the 'stuck at 0%, then error 262' behaviour you describe above.
still stuck... what i did:
- use mtty to issue the boot command : Command error
- use different Shipped ROM Images : wrong version whilst updating
-
still stuck... what i did:
- use mtty to issue the boot command : Command error
- use different Shipped ROM Images : wrong version whilst updating
anyone got a german 1.56.407.3, radio 1.27.12.32 shipping version?
- try to install rom image using SD: stuck with blank screen and "Loading...." comment
So I am running out of ideas. If I got everything right, the ONLY chance
to re-animate it is to get the one and only original rom setup version?
any way to install HardSPL via SD-Card?
Martin
e-men said:
still stuck... what i did:
- use mtty to issue the boot command : Command error
- use different Shipped ROM Images : wrong version whilst updating
anyone got a german 1.56.407.3, radio 1.27.12.32 shipping version?
- try to install rom image using SD: stuck with blank screen and "Loading...." comment
So I am running out of ideas. If I got everything right, the ONLY chance
to re-animate it is to get the one and only original rom setup version?
any way to install HardSPL via SD-Card?
Martin
Click to expand...
Click to collapse
Try flashing to this ROM
ftp://xda:[email protected]_Radio_22.45.88.07_1.27.12.17_Ship.rar
e-men said:
So I am running out of ideas. If I got everything right, the ONLY chance
to re-animate it is to get the one and only original rom setup version?
any way to install HardSPL via SD-Card?
Click to expand...
Click to collapse
It's very unfortunate your SPL doesn't support the "boot" command
Find a rom with CID = HTC__102 and ModelID = KAIS13000
You can find these values with a hexeditor in the RUUsigned.nbh (extract it from an original rom update)
You can rename RUUsigned.nbh to KAISIMG.nbh and put it on SD card. Just enter the bootloader and flashing will start. But it also checks if CID and ModelID match with your device.
Thanks alot, but:
Error [262]: Update Error
and its a KaiserCustomRUU which I thought only works o.k. if
HardSPL was applied correctly ?
Martin
jockyw2001 said:
It's very unfortunate your SPL doesn't support the "boot" command
Find a rom with CID = HTC__102 and ModelID = KAIS13000
You can find these values with a hexeditor in the RUUsigned.nbh (extract it from an original rom update)
You can rename RUUsigned.nbh to KAISIMG.nbh and put it on SD card. Just enter the bootloader and flashing will start. But it also checks if CID and ModelID match with your device.
Click to expand...
Click to collapse
I´ve got a second, working, perfect TyTN with the matching rom image. any chance to read out the ROM and use that one to boot?
I followed the thread about ROM extraction, but it says I need HardSPL to unlock, otherwise it will not be able to update ?
Same problem!!!!
e-men said:
Thanks alot, but:
Error [262]: Update Error
and its a KaiserCustomRUU which I thought only works o.k. if
HardSPL was applied correctly ?
Martin
Click to expand...
Click to collapse
Same problem here with my brand new TyTN II... Please help! i got it just one day
I am looking for an answer too. It seems that from 1.82.00.00, there is another layer of protection against JumpSpl. My experience is you need the original Rom to flash back, which works for me. Although you do not have the rom you desire but at least you unbrick you phone.
japher said:
Exactly the same thing happened to me Everyone here shouts about flashing HardSPL first (and then it's "impossible to brick your phone"). Unfortunately, people rarely mention that the phone can be bricked whilst trying to flash HardSPL!
With mine, I did initially receive an error when using the 'boot' command, however when I did the following, it worked:
- uncheck 'allow usb connections' in activesync
- get the phone into the tri-color screen and plug the usb cable in
- start mtty, select usb
- issue the 'boot' command (without ANY other commands being issued
before it).
Have a look at this; http://forum.xda-developers.com/showthread.php?t=369567
just might help
King
Click to expand...
Click to collapse
i got the same problem... when i haved installed hardspl it froze to 99% and give me back 262 error. now i'm retrying but don't work..
what can i do?
solved using mtty.exe
ffffffff said:
japher said:
Exactly the same thing happened to me Everyone here shouts about flashing HardSPL first (and then it's "impossible to brick your phone"). Unfortunately, people rarely mention that the phone can be bricked whilst trying to flash HardSPL!
With mine, I did initially receive an error when using the 'boot' command, however when I did the following, it worked:
- uncheck 'allow usb connections' in activesync
- get the phone into the tri-color screen and plug the usb cable in
- start mtty, select usb
- issue the 'boot' command (without ANY other commands being issued
before it).
Have a look at this; http://forum.xda-developers.com/showthread.php?t=369567
just might help
King
Click to expand...
Click to collapse
Hi there!
Which version numbers does your TyTN have? Mine does not respond
to boot command (says "Command Error:")
Click to expand...
Click to collapse
i've the same problem. i can't install nothing because lost connection at 0%
mtty is a solution for my problem ?
How do I use it?
e-men said:
ffffffff said:
Hi there!
Which version numbers does your TyTN have? Mine does not respond
to boot command (says "Command Error:")
Click to expand...
Click to collapse
You might want to try leave a gap between > and Boot when using mitty, it works for me.
Click to expand...
Click to collapse
>i've the same problem. i can't install nothing because lost connection at 0%
I have tha same proble but with touch dual!!!!
ffffffff said:
e-men said:
You might want to try leave a gap between > and Boot when using mitty, it works for me.
Click to expand...
Click to collapse
nope.. does not work.
restarting mtty - does not work
reset (hard,soft) TyTN - does not work
type "boot" before the prompt comes up - does not work
type " boot" - does not work
type "BOOT" - does not work
all different types of "boot" "restart" whatever - does not work
any more ideas? any check within my spl possible for a set of commands?
Click to expand...
Click to collapse
Hi All,
I have been trying to unlock my T-Mobile MDA Vario 3, after repeated trials I managed to copy SSPL-KAIS.exe onto the Device, started it, then unpug and plug back the USB.
Then I followed the instructions and the flash update process started, this went up till 95% complete, then it failed with an update error.
Now when I reboot the device I get a tri colous display which says the following by the top left hand corner:
Kais 130
SPL-1.56.0000
CPLD-8
At the bottom it says Serial, then if a USB is connected, it sasys USB. If I try to run the flash again, this time around it is stuck at 0% and eventually returns an update error.
Any help will be much appreciated.
Thanks
Please ask in the thread discussing the unlock method you are using.
My phone is stuck on the color block screen
RUUNBH is in the upper right corner.
It also has
KAIS1*0
SPL_3.02.0000
CPLD-8
I have been trying all day to fix it but nothing works. HELP!
leciathegunner said:
My phone is stuck on the color block screen
RUUNBH is in the upper right corner.
It also has
KAIS1*0
SPL_3.02.0000
CPLD-8
I have been trying all day to fix it but nothing works. HELP!
Click to expand...
Click to collapse
Try reflashing your original rom, and look here for more solutions.
http://forum.xda-developers.com/showthread.php?t=423486
I tried but for some reason the loading process keeps failing. The sync icon stays green and a message comes up on my comp saying that one of the usb devices attached has malfunctioned.
leciathegunner said:
I tried but for some reason the loading process keeps failing. The sync icon stays green and a message comes up on my comp saying that one of the usb devices attached has malfunctioned.
Click to expand...
Click to collapse
Read that thread again.
The wiki page has instrcutions on how to remove RUUNBH using MTTY.
Dave
what is mtty? Is there something that I can download?I don't know where to begin. The thread you were referring to said For the AT&T Tilt with any SPL below 1.93 the proper sequence for RUUNBH errors is:
cmd> set 16 0
cmd>boot
My SPL is 3.02
leciathegunner said:
what is mtty? Is there something that I can download?I don't know where to begin. The thread you were referring to said For the AT&T Tilt with any SPL below 1.93 the proper sequence for RUUNBH errors is:
cmd> set 16 0
cmd>boot
My SPL is 3.02
Click to expand...
Click to collapse
You need to goto this wiki page and read this section: If RUUNBH is still showing on the Bootloaded
Ta
Dave
DaveShaw said:
You need to goto this wiki page and read this section: If RUUNBH is still showing on the Bootloaded
Ta
Dave
Click to expand...
Click to collapse
Nothing is working. I can't establish a usb connection so I have no way of getting anything to myphone. This is frustrating. I have been trying to fix my phone since tuesday. I feel like pulling my hair out!!!