Related
While a lot has been written, the following should provide an easy-to-follow guide:
Preparation:
1. A torch (read on and you will know why)
2. 256M SD card
3. Download ntrw.exe, romupdate.exe, hexedfull.exe from the ftp of this forum to c:\ and install hex editor
4. Download the appropriate ROM file (hereafter referred to as "newrom.nb1").
5. Cancel USB in ActiveSync
6. Use Sprite Backup to backup your ppc
Backup original ROM:
1. Put pocket pc into the boot loader mode (hold both on/off and camera buttons at the same time while resetting).
2. Insert empty SD card.
3. Connect pocket pc to pc through USB.
4. Run romupdate.exe on pc.
5. Select “\\.\WCEUSBSH001” in port settings. In the popup windows, enter “d2s” and press enter.
6. Don’t get panic to see the pocket pc screen goes dark. Use your torch and you will see the download percentage. Wait until it reaches 100% and shows “CheckSum is OK!”.
7. Insert SD card into card reader of the pc. Ignore the “format SD card” message and click “No”.
8. Run “command” to go into DOS prompt and change to root directory (cd c:\). Enter “ntrw read oldrom.nb1 s:” where s is the drive of your SD card.
9. Ignore the “Data error <cyclic redundancy check>” message. You should save another copy of this important rom file “oldrom.nb1”.
Change header of newrom.nb1:
1. Right click on oldrom.nb1 to open hex editor. Copy the first 416 bytes.
2. Open the downloaded newrom.nb1 file and overwrite the first 416 bytes with those of the old rom.
3. Save the edited newrom.nb1. You may save another copy of this important file.
4. Go to the command prompt and enter “ntrw write newrom.nb1 s:” to write it to the SD card. Ignore the error message “The parameter is incorrect”.
Update the ROM:
1. Insert SD card into pocket pc and put it to boot loader mode again (on/off + camera + reset). Use you torch to check the dark screen.
2. When it shows “Press Power to flash”, press the on/off button. Wait until it reaches 100% and ignore the message “Download Fail - CheckSum Fail”
3. Soft reset your pocket pc.
4. You may have to reinstall your software, unless you are familiar with the advanced features of Sprite Backup.
Ask you a question.
Does it backup 3 parts of rom (OS rom, extended rom and Radio rom)?
I am trying to backup my old Qtek Rom so I can install an update. I follow the steps to perfection..
The file created by ntrw is 999Mb big and at the end of the file I get an error stating that "parameters are incorrect"
Does this mean that the backup was not done successfully?
Why is the file so large?
Thanks for your help
ntrw get image SD card. Use SD card 256 Mb.
SD Card update problem
Hi I used ntrw.exe to backup my original rom to an SD card. It all went ok and I was able to clear the SD, write the rom back on the SD and put it in my M500. Normally I got a menu to press the power button to flash the rom to my phone, but now whatever I do I can't get the menu back. I won't get the option "Press power button" to flash. What I also see is that somethimes when I put the SD back in my laptop it is totaly empty. Normaly it would ask me if I want to format the SD because it can't be read. Can anybody help??
Thanks!
Dear All,
this is my first time to this site.
Could you please send me the download links for the files that are necessary (or the files themeselves) to backup the ROM (ntrw.exe, romupdate.exe, hexedfull.exe )
Thanks a million.
Will
i found this http://www.ccoo.net/MDAFlash/ntrw.exe
Thank you for this wonderful guide !!!
I am trying to backup my I-Mate JAM's ROM with a 256 MB SD card. However I have a similiar problem where when the ntrw.exe completed with the same "parameters are incorrect" error. The created ROM image is about 247,040 KB.
Is this correct? I did make sure the SD card is empty before the backup process (by deleteing everyfile on it), or should I use some proper method to ensure the SD card is actually completely empty?
Thanks in advance for any help!
Mine came up with that every time, but worked ok. I am trying to do the Anasky ROM update to my magician, and the backup i made of the original rom was fine to restore, even though i got that error.
mitchello said:
Mine came up with that every time, but worked ok. I am trying to do the Anasky ROM update to my magician, and the backup i made of the original rom was fine to restore, even though i got that error.
Click to expand...
Click to collapse
Thanks a lot for this info! It certainly make me feel a lot more confident about what I am doing
Thanks again !
Jyhnc said:
Thank you for this wonderful guide !!!
I am trying to backup my I-Mate JAM's ROM with a 256 MB SD card. However I have a similiar problem where when the ntrw.exe completed with the same "parameters are incorrect" error. The created ROM image is about 247,040 KB.
Is this correct? I did make sure the SD card is empty before the backup process (by deleteing everyfile on it), or should I use some proper method to ensure the SD card is actually completely empty?
Thanks in advance for any help!
Click to expand...
Click to collapse
someone in this forum told us that the rom size is vary and closed to the size of your sd card.
I used 128mb to backup and restore, it worked fine.
Has anyone experienced the problem of trying to reflash the device with the SD and when placed in Bootldr, the display just says serial and never progresses to press power to flash??
thanks
Jim
turn off the USB connection in your activesync, it will interfere the upgrade.
Found the fault, I reconnected the USB whilst entering the bootldr with the SD in socket and worked fine... Quite strange though as I couldnt remember having the USB connected the lasst time I performed the process
rgds
jim
jfran said:
Found the fault, I reconnected the USB whilst entering the bootldr with the SD in socket and worked fine... Quite strange though as I couldnt remember having the USB connected the lasst time I performed the process
rgds
jim
Click to expand...
Click to collapse
Hi All,
I was stuck at the Serial for a Looooooong time. Nothing worked. Until I did the following:
1) Using HHDHexeditor, copy the first 416byte (NOT 220byte!)
2) Write the copied original backup ROM into the new ROM (.nb1 file)
3) Put into your 02 Mini
4) VERY IMPORTANT! - Plug into your USB PORT!
5) Then I see the "Press Power button to Flash!"
and I am happily flashing my device now ... My guess is that it needs to be on external power in order to upgrade .... Thanks everyone .. can't wait to see my new baby with 27Mb storage! :twisted:
I'm using 256Mb SD Card ....
Alvin
How can i know the backup file name stored in the memory card? (*.nb1)
Thx~~
i am not seeing the popup window in which to select "d2s"...can anyone help?
update: Ok, so i was just temporarily blind! Have managed to continue and have fingers crossed it is ok.
2. When it shows “Press Power to flash”, press the on/off button. Wait until it reaches 100% and ignore the message “Download Fail - CheckSum Fail”
3. Soft reset your ppc.
After this.... how I do the soft reset with my ppc?? Connect or diconnect with the USB?? Coz I can't turn it back to the normal from boot loader mode even I do soft or hard reset after the rom flashing.......why?? :shock:
cojones said:
update: Have managed to continue and have fingers crossed it is ok.
Click to expand...
Click to collapse
I get the message ROM size isn't enough when i press the power button to flash from the sd card...why is this?
Talents said:
5. Select “\\.\WCEUSBSH001” in port settings. In the popup windows, enter “d2s” and press enter.
Click to expand...
Click to collapse
WTF ??? The only options are COM1 COM2 or COM3 and the Baud rate.
What a POS!
Hey guys,
Well I succeeded in upgrading to Anansky's BigStorage ROM and was very satisfied, but now my stupid speaker broke (I have a similar problem to other users where they can hear sound if they blow into the speaker). I have to return the Magician so I need to revert back. Can someone PLEASE upload the original XDA II ROM PLEASE???
Here's a list of instructions on how to backup the ROM:
Backing up your ROM can be done by connecting your Magician to the PC through the data cable when you first uncheck the USB connection of active sync.
If your Magician connects with active sync because you didn't uncheck the USB connection in the active sync connection settings then you will not be able to backup your ROM to an SD memory card.
1. Before connecting your Magician you should bring it into the boot loader mode. This can be done by simultaneously pressing power + camera buttons and at the same time the soft reset button with the stylus.
2. After connecting your Magician to the PC through the USB in boot loader mode and having your SD card inserted into the MDA, you run romupdate.exe.
3. Then choose the USB connection in the connection settings of romupdate.exe window and click on ok. After that a terminal window will popup in that window.
4. Type d2s and press enter. Your Magician will start copying the ROM to the sd card. The screen of your Magician will be dark (no light), but you will see it counting up to 100%. When it reaches 100% it will say it is calculating the checksum. Give it some time till its done and it will say checksum ok.
5. After finishing the transfer of the ROM from your Magician to the SD card, put your SD card into an SD card reader connected to your pc. Your pc might pop up a warning message that says your SD Card is not formatted would you like to format? Click No and open a Command prompt (DOS) window.
6. Change directory to your root directory (cd c:\) and run the command ntrw read o2orig.nb1 x: where x is the drive letter of your sd card. That command will create the ROM Backup file of your ROM into your C drive root directory by the name of o2orig.nb1. Make sure you keep o2orig.nb1 in a safe place and use a copy of that file for the rest of the procedure. Note that after finishing the copy from your SD card to o2orig.nb1 file ntrw might give you an error, just don’t pay attention to it.
7. WinRAR the o2orig.nb1 file, then upload it to the XDA Developers FTP .[/i]
No one wants to help?
The question is why havent you got a backup?? You were told to do this in the first instance should anything go wrong!!
somebody apparently has uploaded the O2 mini original rom, check it out!
The answer to this was I was using my digital camera as an SD reader...and the backup didn't work properly for some reason. So now I have nothing.
The backup (I think you're talking about the O2 Original Dump Rom) doesn't work for me. I have a 1.11 version of the O2 Asia ROM, but I'd rather have the original WWE. Oh yes, and I've tried several times with the "Original Dump Rom" using 220, 415 and 416 bytes...nothing works.
This may work for you - use the romupdate software to get the rom image of your device to the sd card. By this stage you have an edited rom image on the pc. Use ntrw to write that image over the top of the sd card that you have just written to with romupdate. Then plug it into the ppc. Do not format the sd card in the immediate procedure at anytime. For whatever reason I think the romupdate software puts a format on the sd card which the ppc recognises. There were a number of errors on the ppc screen just after installation however when you push the reset button hey hey the original splash screen boots up. Prior to this check that the edited rom header is 416, in my efforts it was not 415. The RomMiniOrg.nb1 image was good with the only NON change being the radio which remained at version 1.11 but I downgraded it to 1.05. I don't think the service centre will worry to much about this should you need it. Goodluck with this, it worked for me.
Hi yozhek,
Thanks for the help. I did what you said but it still didn't work. However, I used O2_mini_asia from the FTP to downgrade my extended rom, protocol and rom version...then I found the Radio downgrade on the FTP and downgraded to version 1.01.
now everything is original!
I didn't know that the Nb1 files did not include the radio stack downgrade so I had to downgrade that seperately.
the command in the romupdate program basically determine which image to backup.
d2s for rom, but I am not sure what's the other command for extended rom and radio. Anybody?
Can I use MaUpgradeUt_noID.exe to change the ROM on my mini with the o2mini_asia.nb1 ?
miniuser: no
you will have to use the process as described in procedure.doc (available in the FTP under anansky's bigstorage folder)
I did as described in the procedure.doc. I have run this command
ntrw write o2mini_asia.nb1 e: and then inserted the SD card into my mini and pressed the power+camera+soft reset button
but it is not doing anything, it has stopped at "Serial" above and v1.00 below for an hour now. Any suggestions?
cheers
mini_user
I tried it second time, now it says
SD DOWNLOAD
==========
SECTIONS=1
Not Allow Update
Any Suggestions?
Cheers
Sorry for the last post, was trying out something else.
I am using a 256MB SD card and the size of the rom is only 127MB after ntrw, does it make any diff??
you can always ntrw write a 127mb rom image into a 256mb sd card.
the rom flash will not work (and hence the no update allowed message) if your rom image in your sd card is invalid for some reason. I make a bobo previously, trying to copy 416byte of anasky rom into my original rom, instead of the other way round. And it give me that error message. After realising my mistake, and did the right modification, the flash went through successfully. so double check your rom header edit if you are not able to proceed to the flash step.
I have a mini with qteck 1.11.00 WWE
and I have download the o2mini rom from xda ftp and have got a 256 mb card
if I want to flash my mini with the o2mini rom the are these the steps to follow
1. dump qtek rom into card
2. copy it to pc
3. copy 1st 416 bytes of qtck into o2mini rom
4. dump o2mini rom into card
5. put mini into bootloader mode
6 update with mini rom
cheers
zenkinz said:
somebody apparently has uploaded the O2 mini original rom, check it out!
Click to expand...
Click to collapse
where is the file?
active sync on my XP cpu, and Windows Mobile Device center on my windows 7 PC both disconnect from my phone when I try to reflash it. everything else works... Please Help!!!!!
Have you tried flashing using the sd card method?
Take your cooked rom and look for the nbh file. Format your sd card and make sure its formatted to fat 32. After the format, copy the nbh file and make sure its renamed to RHODIMG.nbh. Most roms already are named that way but just in case if it isnt, rename it to that. Once its copied, put the sd card back into your phone and put your phone into bootloader mode. (Hold volume down, and hit the soft reset button while holding volume down, and continue holding volume down until you see the multicolor screen) After that, you should see a grey screen. Follow the onscreen instructions and you should be good to go. Hope this helps.
PS. Make sure you put the NBH file in the root directory of the sd card or it wont work. Dont put it in any folder whatsoever.
Heya! I've followed the install instructions in this thread;
http://forum.xda-developers.com/showthread.php?t=1997251
I got to step 5, "enter recovery, on boot led will be violet for 3'', during this period press vol+ ".
I wasn't quick enough on pressing the volume button so it started loading wich didnt do much good i noticed after a while. (stuck on loading)
Soo, i removed my battery to restart the phone, after wich i managed to enter recovery mode only to find myself not knowing how to execute #6, "flash rom zip".
I tried this aswell;
"1) enter recovery at first : after u switch on d phone, when the pink light comes, press up volume key to enter recovery
2) connect your phone to computer using usb cable
3) go to mounts and storage and mount /system and /data.....this will enable ADB in recovery mode
4) now put ur rom zip in the ADB folder of ur computer and start adb and type "adb devices" (without the quotes)
5) if it shows some sort of numbers, then the device is connected successfully
6) in adb. type "adb push /ROM.zip /sdcard" (without the quotes) (ROM.zip is the name of the rom)
7) then reboot recovery, go to flash zip and chose the rom zip and enjoy!"
I fail at #5, since it wont show any numbers. It wont find the device. Many hours of googling and trying different things the result is the same, and im stuck with a phone that wont boot to OS.
What do i do now? Any help appreciated! :victory:
In recovery mode,
Install zip form SD card > install zip from external SD card (if you have put the downloaded zip in your external SD card)
Oh you have to press volume up and down to highlight option, and power button to select it.
Hit Thanks if I helped you!
satan89 said:
In recovery mode,
Install zip form SD card > install zip from external SD card (if you have put the downloaded zip in your external SD card)
Oh you have to press volume up and down to highlight option, and power button to select it.
Hit Thanks if I helped you!
Click to expand...
Click to collapse
My options is as follows;
1. Choose zip from sdcard (i can only access the Tipo internal memory from here, not my removable SD)
2. Apply /sdcard/update.zip
3. Toggle signature verification
4. Back
I can't access my phone storage from my PC either, since the drives wont show. I've tried all drives and such that i've found, but nothing works.
Is there any way i can reverse what i have done (remove clockwork or such) to get my phone to boot again?
Or a way to access my memory, so i can add the zip to the internal storage?
Have i bricked my phone?
Thanks!
You have not bricked your phone. relax.
Well you have to select first option, then under that there should be another line saying 'select zip from external SD card ' or something like that (if I remember correctly) . If that does not work there is a workaround where you use push file via adb. I'm not too familiar with that but will pm you if I find out where I read it.
And now- to revert back,
Download the world fs ftf file found here (its rootable) -
http://forum.xda-developers.com/showthread.php?t=2001567
Download flashtool latest (search) and install (fastboot and flash drivers in particular)
Place downloaded ftf file in c/flashtool /firmware
press flash and follow instructions.
Your on stock fw now. Remember to place zip in internal card if you are attempting cm10 again
Hit Thanks if I helped you!
Woo, somehow i managed to install the stuff! It wont send sound to my headphones though, other then that it's all good.
Thanks for taking your time!
Hi guys,
just a question about flashing rom.. should I do a factory reset or wipe anything on the phone before to flash a rom on mate 8?
thanks
toXa
Shouldn't need to no. Just download the file and extract the UPDATE.APP file (just that file - don't make my mistake and copy over all the files 'just in case' as it doesn't work), pop it in an external sd card 'dload' folder, turn off, hold vol up & down & power, release power on logo appearance and let it do its thing
I had a crash course in this over the last two days..