So i just flashed my vox with dr.gonzo's new 1.0 rom...and I did it the same way i've been doing it for months now (since his first rom 0.1) and it all went good, but when it was suppose to reboot turned off but never turned back on....I turn it on manually and i see the htc logo, it vibrates and then black screen... nothing happens afterwards...please dont tell me its bricked...please.....
If you're not able to get it into the bootloader to run an RUU then I suggest that you flash a signed HTC ROM, flash USPL and then re-flash New Guava v1.0
how do i flash a signed htc rom? when i turn it on, the htc logo comes on, then vibrates, and then a black screen.... when i try a hard reset, it asks me to confirm by pressing send. i press send (correct me if i'm wrong, send is the green 'phone' button right?) and it loads up the htc logo, vibrates and then shuts off. I've never had a bricked phone before, this all just doens't make sense i did the same steps that i've always done.
Seriously? Your phone is not bricked.
If you've flash a ROM before, it's the exact same procedure - what you can try and do is load into the bootloader by holding the camera button and plugging in a USB cable, it will start into the tri-color screen and should show USB is connected then you can flash a signed HTC ROM.
If the ROM is corrupt, this is your best way of "recovering" your phone, if the ROM was flashed properly, after getting into the bootloader, run ruurun 0 and ResetDevice to boot it back into OS.
oh ok, i haven't tried that yet (bootloader mode that is). Now you say i do this by plugging the usb and holding the power button and camera button? is that how it works? h4waii, you just lightened up my day by giving me some hope!
That is how you can enter the boot loader.
1). Turn off and unplug the Vox from external power/USB cable
2). Press and hold the camera button
3). Insert external power/USB cable
4). Continue to hold camera button until you enter the tri-color screen
At this point, you should have a "USB" text label on the bottom left hand side indicating USB is detected - you can then run an RUU from a signed HTC ROM to update it.
press and hold the camera button alone? i tried that, it doesn't power up the unit though?
Yes it does. Hold camera and plug in your USB cable (making sure it's also plugged into your computer).
ok i got it to the triband screen, but when i ran dr.gonzo's rom it got to 3% and said its corrupt. so i'm gonna do what you said and flash a signed htc rom. hopefully it works....
Yes, 3% because SPL is not patched to allow an unsigned ROM to be loaded, flash an HTC ROM to it, once that is complete you can run USPL to re-flash New Guava.
It will work, don't need to hope
you are a godsend! literally have no idea how depressed i was yesterday! being a university student money is very tight right now so was a total shock when i realized i bricked my $350 phone....I wish i had money cause i'd send you some for being so helpful but I dont... So just please understand i REALLLY appreciate your help, thank you.
That's what we're here for. Glad to be of service.
Hi,
my Imate JAMA (P30) doesn't boot, it reamins stuck up at the imate screen and then screen goes blank and nothing happens even if i press any key it appears to be off and turn back on only if i remove and reinsert the battery.
i've tried hard reset by pressing the Volume(-) and the Red hang up button but in vain.
even when i connect USB cable to my device, it is not deteced by my PC nor by AciveSync.
what should i do?
Please Help !!!
ravisharma said:
Hi,
my Imate JAMA (P30) doesn't boot, it reamins stuck up at the imate screen and then screen goes blank and nothing happens even if i press any key it appears to be off and turn back on only if i remove and reinsert the battery.
i've tried hard reset by pressing the Volume(-) and the Red hang up button but in vain.
even when i connect USB cable to my device, it is not deteced by my PC nor by AciveSync.
what should i do?
Please Help !!!
Click to expand...
Click to collapse
welcome to the forum
Please READ the Wiki, you`ll find a lot of usefull information
i'm new here, please explain I din't get wht do u mean by "Please READ the Wiki"...
http://wiki.xda-developers.com/
Your battery may be dying. Try a new one.
Naa, I've charged the battery still the same problem
whats the status. i have the sme prob. what can i do now??
Hi.
I was trying to Upgrade my O2 XDA Exec Rom with Xda_Exec_Upgrade_v1.30.162. The process went successfully till 100%. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Hi guys!
i have a problem today i got from sync notification about os update so i pressed yes it started to download and install then my phone powered off and i cant turn it on again .
when i press the power button and hold it the phone vibrated again and again i tried flushing os again (no first time) no help
when i cinnect the usb to phone without pressing return button the green light turns on automaticlly pls can any help me??
thnx for trying to help but i fixed it
i boot relocked the phone and its ok )))))
can you access bootloader mode?If so download your phone's stock rom insert your sdcard into an sdcard adapter and flash it
Hi, I need help (sorry for my english)
Yesterday, i've done an upgrade of my nexus s with the ota message.
Unfortunatly, the upgrade didn't work and my phone was not responding.
With Adam tool, i was able to put my device in download mode only with the Galaxy S device (not the Nexus S).
I put some KERNEL, PARAM, BOOT ... on the device with the Heimdall-frontend program.
Now my phone is no longer recognized by windows.
When i start the device, first seach and home ligth is on, then the four ligth is on (home, search, menu and back). After that, the flash ligth turn on with the four button ligth on. And nothing happend.
When i plug the usb, all the ligth turn off except the search and home ligth, but the UnBrickable.jar does not detect the phone.
What can I do ?
Please Help