Database Info

Advanced Shelltool help

Hi everyone. I am in need of assistance with shelltool. I've been flashing ROMs for quite some time and this goes beyond the scope of typical upgrading. I apparently had a bad flash happen and need some help correcting it. The OS appears to work fine, except some applications .cab installers exit before asking device or storage card. I have attempted to load the EnableRapi.cab and Cert_SPCS.cab; however, they exit almost instantly after starting them.
I had this situation happen once before and I was able to oddly enough try to load the original T-Moblie ROM through shelltool (didn't install at all), then try NBD 8.3. which brought me to a boot loader screen after doing a hard reset, but didn't install NBD 8.3. So far I'm not having much luck in recreating the experiment.
Is there a way to force a Wizard into bootloader mode using shelltool or some other utility? I can restore the device if I can get that far.

it's time for my first post
Hi, have been reading this forum for about 3 month and i enyoy it and learn a lot. Have been try about 7 roms and like all. It's time to payback.
Yo can enter bootload by pressing and holding the voice command button and then softreset, keep holding the voice command button util you reach bootload.
Other thing you can do is run the original rom by its executable program not using shelltool.
Good luck

Awesome! That rescued my phone. You saved me quite a bit of time in getting my phone back to a working state. You've more than given back!

Dezl0ck said:
Awesome! That rescued my phone. You saved me quite a bit of time in getting my phone back to a working state. You've more than given back!
Click to expand...
Click to collapse
no problem, that's why we are here for, to help each other

Help, Stuck at multicolor screen. XDA Mini S
Dezl0ck said:
I can restore the device if I can get that far.
Click to expand...
Click to collapse
Please tell me how did you restore your phone? i am flashed touchflo rom to my phone and some how it is stuck to the multicolor screen.
Can you help me out?
Thanking you in anticipation.

1 put phone into bootloader by pressing and holding camera button+reset hole. Keep holding the camera button untill you see the tricollor screen.
2 plug the phone into the computer (wait to hear the noise that it found hardware
3 Flash a rom you know worked (maybe your original/ maybe someone elses... maybe even mine )
4 wait untill the flashing finishes and "Tap Screen..." appeares before unplugging.
(If you have a G4 then I advise you to flash the original rom, or make sure your ipl/spl is propper. check the G4 forum to be sure, or ask Mestrini - The creator of the Wizard service tool. I believe he has a G4 and knows more about it than most)
Happy Flashing

Randomly get Update/Connection errors.
Thank you very much for the response.
Unfortunately, i am still not able to flash the ROM. I did the follwoing steps, can you please help me letting me know, where m i wrong?
I restarted my PC.
I did Reset my PDA, by removing and placing the battery.
then i boot the PDA, it always boots to the TRICOLOR Screen.
afterwards, i tried to flash following ROMs
Xda_Minis_Upgrade_v2.21.4.101.exe [the oringal one, used to be working since long]
SNN_Version_3.0 [i flashed this, some days ago and worked fine for me]
SNN_3.0_FULL_version [the ROM that caused the problem]
BUT no use, i randomly get following errors:
ERROR [262] : UPDATE ERROR
ERROR [274] : CONNECTION
and some other errors.
Pleaaaaaase some one help me.
Thanking you in anticipation.

Help with a "Bricked" Tilt!

Any Help Appreciated. Anyone ever seen this type of "Brick"?
After flashing a new ROM (Tilt XDA-Live v1.0 - fully flashed to 100% and said finished), the device won't boot. It just gets stuck in an endless loop. It trys to boot, shows the AT&T screen, then reboots/resets back to the beginning before getting to the Windows mobile screen.
The only way to get it to stop the loop is to pull out the battery. Put the battery back in and power on and you get the loop again.
I have loaded HARD SPL (1.0.OliPof).
I can get into Bootloader mode by pressing power/camera then reset.
In this mode, I can get it to reflash the ROM (and even other ROMS) but it still ends up in the same loop.
I have tried flashing the Official ATT WWE ROM from this thread but it still loops at boot.
I did the "original/problematic" flash using Vista. Could that be the issue? I have done subsequent "recovery" flashing using XP to no avail.
I have flashed several ROMs to my Tilt in the past (Mostly Dutty ROMs).
I had a Hermes before and flashed that a million times no issue so I'm not a complete noob.
Any ideas? I'm stuck with a brick!
Thanks in advance.

I'm in the same boat. I've flashed over and over (with different ROMs) and am still stuck. But I did every flash from MicroSD card. Did you get any help?

No input yet.
What ROM did you flash that started the problem for you?

dutty's touchflo rom beta for the tilt. i was on dutty's hybrid rom version 3. after flashing the OEM at&t ROM, i'm out of ideas. stay in touch if you find a fix. i'll keep searching.
- J

Bump...
Anyone else seen the issue with a Tilt stuck in a "boot loop" after flashing (see first post)?
Paypal reward for anyone who helps me recover - otherwise I'm going to have to go buy another Tilt (which I could live with but worse yet, I may be stuck with the stock ROM because I'm too gunshy to go back to my flashing ways)

Tried all day to find a fix. Think I made things worse. Read up on some threads using the mtty tool and ran a command (task 2a) that cleared the flash. But now it doesn't even boot to a splash screen, and I can't get back to bootloader mode.

This might sound a bit stupid, but I have taken note that my device upon flashing the new at&t rom actually held some of the information, you would think that a hard reset is performed after a rom flash, but that just wasn't how it worked out for me, anyway I had a radio that wouldn't come up, but would after a hard reset, this was directly after flashing my tilt...
?Glitch

Glitch,
Yeah, I have heard in several places that you need to hard reset after a flash to clear out all the settings from the old ROM. Seems odd since you just overwrote ROM - I think of it as a format (HDD mindset) but I guess it's not a clean format.
Jerich007,
Sorry to hear you went backwards. I stopped flashing my Tilt for the same reason - worried about getting farther in the hole without some expert advice. My next step was to try the MTTY tool just as you noted. Guess I'll go that route as a last resort. If it's any consolation, I seem to remember reading about plenty of people recovering from a "brick" that won’t go into bootloader mode.
Hopefully someone trolling the waters will see this thread and take up the offer for a Cash Reward (Paypal) for help recovering this Brick!

ill put up some paypal $$ for a fix as well. i'm at the end of my rope on this one. i'm subscribed to some other threads so hopefully we'll get some feedback.

It is not so serious as you think! Try the following way:
1- Download the original rom from AT&T (the 1st rom was installed on your device)
2- Turn your bricked Tilt to bootloader ( http://wiki.xda-developers.com/index.php?pagename=Kaiser_Resets )
3- Start flashing your Tilt with the above AT&T rom.
Evething should be OK after that! (but your device need to be installed Hard-SSPL before!!!)

try...
try this link
http://forum.xda-developers.com/showthread.php?t=286755
and maybe these
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
http://forum.xda-developers.com/showthread.php?t=334693&highlight=how+to+unbrick
http://forum.xda-developers.com/showthread.php?t=344402&highlight=how+to+unbrick
don't forget that some of this info isn't for the tilt...
good luck, and be careful

This ROM solved my issues
try this thread
http://forum.xda-developers.com/showthread.php?t=327482
and DEFINETLY download the ROM, flash it. Once it's flashed,then ya can reflash any ROM ya want. Get the newest stock ROM from the sticky and reflash it (if ya want the ATT ROM)
That will fix it.
(I reflashed Tilt XDA-Live v 1.0, and it's working GREAT.)
I did the same thing to my Tilt.
That ROM saved me.
Alemaker

Problem is I can't get to a bootloader screen now. I press Camera+Power+reset, but all that happens is the green LED goes off then on, and then the screen is blank. Anyone know any other tricks? I think I may have erased my bootloader using mtty command 'task 2a'.

...
Hate to say it, but if after hours of searching on the forum you can't find an answer, i'd pm a pro like pof. I don't know if that will work, but their advice is the only thing i'd listen to.
Don't forget to give a lot of detail and maybe mention what you've tried.

Thanks. I've already PM'd pof and olipro. Hopefully they can come up with something.

jerich007 said:
Problem is I can't get to a bootloader screen now. I press Camera+Power+reset, but all that happens is the green LED goes off then on, and then the screen is blank. Anyone know any other tricks? I think I may have erased my bootloader using mtty command 'task 2a'.
Click to expand...
Click to collapse
****, I should have replied after someone posted all those links to Hermes unbrick procedures, to never do a task 2a from hardSPL. It reformats entire flash including SPL and the problem with hardSPL is that you can't flash another SPL, even if you would have tried before rebooting
Anyhow, your only chances to unbrick your device are to try to enter radio bootloader (there is a radio bootloader running on the mARM (ARM9)) and then to flash it. However, only service centres have such flashx utilities I'm afraid. Furthermore I'm not sure if radio bootloader can be entered directly, usually you can enter it via the normal CE SPL. You can try to first connect USB and then press reset with the stylus while holding the Voicecmd key. If you are in XP, then three new devices should be found (composite USB, a modem and a diagnostics port). Download the Motorola "Q" usb drivers, these will work just fine. In this mode you will have to authenticate to the radio bootloader before you can start entering commands. We'll get to that if you manage to connect. Your other chance to unbrick is via JTAG. I know the kaiser has JTAG points scattered on PCB.

Ok, thanks, I'll search for those drivers and let you know. By Voicecmd key do you mean the push-to-talk key along the side or the talk key with the green phoneset icon?

The top button at the left hand side

Ok here's what happens:
1. downloaded Motorola USB drivers (32-bit) from their site, installed and rebooted.
2. plugged in Tilt via usb cable, 'found new Hardware wizard' starts.
3. clicked next to auto-search for drivers, but the wizard fails with 'cannot install this hardware' message. I have 3 yellow question marks in Device Manager for 'Data Interface' devices.
4. held down Push-to-talk button and hit soft reset. No change, no leds are lit, screen is off.
Did I grab the right drivers?

Not bad at all. Apparently your phone is in Qualcomm DIAG mode, probably as a consequence of task 2a Now you can forget about rebooting with Voicecmd pressed.
Either you've got the wrong drivers or you don't install them in the correct way. Go in device manager, right click one of the 3 and update driver, then 'install from a list or specific location (Advanced)', then check 'Include this location in search' and enter the driver path. I'll take a quick look if I can find the drivers for you, I vaguely remember they were on mobile-files dot com.
EDIT: found the drivers, attached. The VID and PID of the found usb devices should be VID_05C6&PID_6000. Take a look in the device's advanced tab in device manager.
PS: Although diagnostics mode sounds great, I haven't yet found a way to flash the device. Perhaps it works with that Hermes radio flasher MaUpgrade_NoID.exe
Guys with a working SPL can enter radio bootloader DIAG mode via "rtask b", exit MTTY and install drivers. It would be great to know if someone has a htc/qualcomm radio flash utility (perhaps MaUpgrade_NoID.exe is what you need)

Lost Connection On 100% Flash, Not Auto Rebooted, HELP!

Just for completeness I will go through my full process:
1. Installed HardSPL
2. Installed Dutty's WM6.1 Official UC 5.2.19199 RTM
3. Discovered that there wa no sound so set about finding a solution
4. Downloaded NIKI_Radinly_1.58.16.27_CustomRUU
5. Installed HardSPL again as would not connect
6. Installed NIKI_Radinly_1.58.16.27_CustomRUU
Problem is that it reached 100% on the install then said it had lost the connection (made USB disconnect noise and everything). The NIKI radio installer only had an exit option and cannot reconnect. The phone is on 100% and won't go any further.
I am very worried about what to do next as clearly I could be in a bad flash situation. Any advice on what to do and what I may have done wrong would be very appreciated ASAP.

Oh I have backed up my phone first so hopefully no data will be lost (just potentially the phone itself )

if you already hard spl correctly then you dont have to do it again.....now you need to put your phone in tricolor mode (press power button and camera button at the same time and while holding then down soft reset with your styles...then you would be in tri color mode) then connect to PC and reflash rom and radio!
PS. please read the wikis on duttys (after flashing tutorial) as you would need to hard reset after! flashing rom for the first time!
Rene

you can try Sd Card flashing method...that would be easier

Thanks, I had to take the battery out to get it to restart. Luckily it seems to have got the Radio ROM in there as it rebooted working fully. Didn't know you could go back to the tricolour mode so easily after installing hard spl. Will see if it runs OK for a day or two b4 I get the bottle up to try again
I did have a good read before both installs. As a newbie though the sheer number of combinations and options make it quite hard to follow what you should be doing in each situation. I think that is why so many people are asking the same questions on lack of sound, etc.

rock4mayo said:
you can try Sd Card flashing method...that would be easier
Click to expand...
Click to collapse
Thanks for the advice, will try that next time

Nevermind I see you got it working again. If it should reset back to SPL, let me know & we'll diagnose it for you.

sibeer said:
Thanks, I had to take the battery out to get it to restart. Luckily it seems to have got the Radio ROM in there as it rebooted working fully. Didn't know you could go back to the tricolour mode so easily after installing hard spl. Will see if it runs OK for a day or two b4 I get the bottle up to try again
I did have a good read before both installs. As a newbie though the sheer number of combinations and options make it quite hard to follow what you should be doing in each situation. I think that is why so many people are asking the same questions on lack of sound, etc.
Click to expand...
Click to collapse
everyone is a newb at one point but as soon as you read and read and learn its farely easy as the great people on xda have made it....good luck flashing!!

Help!! Can I Revive My Tornado!!!

Hi. Can someone please help me out? I was trying to flash my cingualr 2125 from wm 5.0 to 6.0. I was using Kar Hoe's instuctions and I used the typhoon instuctions instead of the tornado instuctions. I didn't know there was a difference at the time.
I did all the steps up until step 5 on the typhoons where it states you will get a white screen. At that point, I accidently hit my usb and the phone disconnected from active sync. I thought if I took my battery out, I could just do a reboot and get the reboot screen. Well I got nothing. I cannot even turn the phone one. I cannot even connect to active sync. I thought maybe I fried the battery and bought a new one and no luck. I have done a hard restart and all other things that I could think of.
Does anyone know if I had hurt the phone and if it can be fixed to get to the bootable screen. I would be happy just to get it to power on and stay with wm5 just to have the phone working.
I really appreciate your help.
Khernden69

Aah i remember doing the same once i screwed up my newly acquired tornado with typhone rom. phone was dead no bootup screen nothing, i tried every thing asked everywhere, thankfully i had warranty period so went to them with very innocent face and made up a story that "i switched it at night and it wont boot in the morning" they bought and gave me a new phone after a week. any ways GOOd Luck

Enjoy WM6

think your in trouble mate. Using the wrong rom and cancelling it half way is a big no no. Least you have a fancy paper weight

Similar problem
I have just acquired a tornado (in it's o2 guise) and it will only get as far as the wm splash screen. I thought trying a hard reset or flashing it with a new rom might revive it. However I tried hard reset (holding down the 2 soft keys beneath screen while pressing power button?) but it just kept booting to the splashscreen. The phone doesn't boot far enough to be recognised by Activesync so can't flash it. Can anyone suggest a solution? Would going to bootloader mode allow me to flash it? If so, how do I do that?
Thanks

try this.
1.switch off phone
2. remove battery
3. re install battery
4. hold camera button
5. while holding camera button plug usb cable to port
6. after some second u will see three color bootloder screen
7.format binfs
7. then u can flash correct tornado rom
you can us alternative method for going to bootloder mode
hold camera button while holding camera button press power button(not hold)
GOOD LUCK

Hi fayizk1
Thanks for the tip. Just one question, will this command CID unlock the phone too? It's just the phone isn't CID unlocked, I've tried using instructions and tools on other threads to change the CID value of downloaded roms to that of my phone, but all Typhoonnbftools produces is a 512 byte .nbf file which isn't good for anything. Any suggestions?

binfs not allowed!
When I run format binfs from teratermpro I'm told it's not allowed. What do I do now?

First off, try a couple different times. The "format BINFS" command is case sensitive - where your capital letters are makes ALL the difference. You may need to try a couple times, but I believe "format" is all lowercase and "BINFS" is all capitals.

Thanks djsleepwalker but I tried your suggestion and tried a few times in different cases but still got "Not allowed operation". (If all caps I get "Invalid command") I read somewhere that I'm getting this message because the phone is not CID-unlocked?

Tried a few times in different cases, still get "Not allowed operation". I read somewhere else that I'm getting this message because the phone is not CID-unlocked? Well I know that otherwise I would have just flashed another rom. Problem is I have tried using Typhoonnbftools to change the CID over numerous roms, the file it produces is only 1kb or smaller which is no good for anything. I feel like I'm running out of options...

Just try to flash with a legal WM5 ROM from the magnufacture's web site while the device is in bootloader screen. I hope it will work.
Good luck

This is my problem. There isn't one on their site! I emailed them but they were no help at all.
edit: Have also searched loads of forums etc. no-one seems to have it and there are lots of people looking for o2 roms.

Won't help
timwb said:
This is my problem. There isn't one on their site! I emailed them but they were no help at all.
edit: Have also searched loads of forums etc. no-one seems to have it and there are lots of people looking for o2 roms.
Click to expand...
Click to collapse
Well, I found 'magic' WM5 for SDA, but since it CIM locked, and upgraded to radio 2.0, phone refuse to upgrade (downgrade) to WM5, he said I needed newer file or something... It's stucked in bootloader

I come from China IOICN, but I can not help you, because my bad English.

timwb said:
When I run format binfs from teratermpro I'm told it's not allowed. What do I do now?
Click to expand...
Click to collapse
try first
info 2
then
format BINFS

Still says "Not allowed operation!"

timwb said:
Still says "Not allowed operation!"
Click to expand...
Click to collapse
can you get any information when you try "info 2" command?

Yeah
info 2 displays results ok

I've RESEARCHED, and found no answers. I think it's bricked

Hello to all, I am a noob here and have tried to adhere to all of the demands to do research and not post ?'s, but I am at a wall.
I have a Tilt and I ran the sim unlock and I was using the Sleuth 3.0 on it. Everything was working fine. I added the Iunlock cab and it worked fine as well. I then tried to install the icontacts, but i would have to go to program files and icontacts file in order to use I contacts. Well, wanna be innovative me thinks to try and move that file so it would replace something. I copied it to the windows appbuttons folder and deleted the regular contacts and nothing happened, then I put it in the start up folder and no luck, then I simply copied it to the windows folder not at the bottom where all of the extra files are. After that I tried to reset it and now all that I get is the bootloader screen. it reads as follows:
KAIS1*0 MFG
SPL-1.0.Olipof
CPLD-8
At the bottom, it shows either USB or Serial depending on if the usb is plugges up.
I tried running the sim unlock again and the dutty rom and both load to 100% but it goes back to the same screen. Any help would be greatly appreciated. Please help and thank you so much.

barrnunn said:
Hello to all, I am a noob here and have tried to adhere to all of the demands to do research and not post ?'s, but I am at a wall.
I have a Tilt and I ran the sim unlock and I was using the Sleuth 3.0 on it. Everything was working fine. I added the Iunlock cab and it worked fine as well. I then tried to install the icontacts, but i would have to go to program files and icontacts file in order to use I contacts. Well, wanna be innovative me thinks to try and move that file so it would replace something. I copied it to the windows appbuttons folder and deleted the regular contacts and nothing happened, then I put it in the start up folder and no luck, then I simply copied it to the windows folder not at the bottom where all of the extra files are. After that I tried to reset it and now all that I get is the bootloader screen. it reads as follows:
KAIS1*0 MFG
SPL-1.0.Olipof
CPLD-8
At the bottom, it shows either USB or Serial depending on if the usb is plugges up.
I tried running the sim unlock again and the dutty rom and both load to 100% but it goes back to the same screen. Any help would be greatly appreciated. Please help and thank you so much.
Click to expand...
Click to collapse
You could hard reset if you altered something in WM to cause it not to boot...hopefully

I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?

barrnunn said:
I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?
Click to expand...
Click to collapse
Yeah and then you press send...
- well you could try go into the bootloader and flash an OEM original ROM on i do not believe that doing this would brick your kaiser.

zeezee said:
You could hard reset if you altered something in WM to cause it not to boot...hopefully
Click to expand...
Click to collapse
In case u dont know how to do it:
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Resets

Or else search for MTTY. That helped a lot of ppl who got stuck in boot loader.

barrnunn said:
I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?
Click to expand...
Click to collapse
U need to hold the stylus in the hole longer, untl a message pops up on the page.
If it does not hardreset or help u, do what zeezee told u - flash a new rom.

OK, thank you all for you diligent assistance. I have tried the hard reset and it does the same thing...goes to black for about 2 seconds, then for a very split second goes to a grey screen and flashes loading then back to the bootloader.
I will try a search for the people stuck in bootloader and try flashing a OEM ROM, I will let you know how it goes. Thanks again.

barrnunn said:
OK, thank you all for you diligent assistance. I have tried the hard reset and it does the same thing...goes to black for about 2 seconds, then for a very split second goes to a grey screen and flashes loading then back to the bootloader.
I will try a search for the people stuck in bootloader and try flashing a OEM ROM, I will let you know how it goes. Thanks again.
Click to expand...
Click to collapse
Here is a list of OEM ROMs:http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs

I do not see any Mods here around or somebody yelling (search button is your friend,search the wiki everything is there, bla bla)To having a woman at home change everything.. Thanks..!

Before you try the dangerous MTTY method, you could try refresh a oem rom w/ the SD method

ok, I am flashing an OEM rom now, but what does it mean to do it with the sd method?

barrnunn said:
ok, I am flashing an OEM rom now, but what does it mean to do it with the sd method?
Click to expand...
Click to collapse
From youre sd card (memorycard), look it up in wiki. Moust of us flashaholics keeps oure rom on oure memorycard and just rename the rom/bootsplash/radio or whateva and place it in root then activate bootloader -> flash. This is an alternative for not using usb cable, pc and active sync
http://wiki.xda-developers.com/index.php?pagename=KaiserSDFlash

ok thanks, but am i correct in understanding that to do that I have to use the phone to access the mem card?
My issue is that the only screen I get is bootloader, no nothing else. I can't even turn it off. I can take the battery out to get a black screen, but any action to try something will take it back to the bootloader screen. But for some reason, it still allows me to flash the ROM, I think. I flash it on my pc and then my phone goes to the grey screen where it shows the % of progress. It reaches 100% and the pc tells me to click finished and I do then it goes back to the bootloader.

barrnunn said:
ok thanks, but am i correct in understanding that to do that I have to use the phone to access the mem card?
My issue is that the only screen I get is bootloader, no nothing else. I can't even turn it off. I can take the battery out to get a black screen, but any action to try something will take it back to the bootloader screen. But for some reason, it still allows me to flash the ROM, I think. I flash it on my pc and then my phone goes to the grey screen where it shows the % of progress. It reaches 100% and the pc tells me to click finished and I do then it goes back to the bootloader.
Click to expand...
Click to collapse
put the rom image file on storage card and than power on phone in bootloader. the process will start automatically.

thesire said:
put the rom image file on storage card and than power on phone in bootloader. the process will start automatically.
Click to expand...
Click to collapse
yes, just use a card adapter or something to acess youre card (if you cant connect via active sync) then copy the rom over and follow the steps in wiki. Beeing stuck in the bootloader some times aint the worse place to be stuck

korakesion said:
I do not see any Mods here around or somebody yelling (search button is your friend,search the wiki everything is there, bla bla)To having a woman at home change everything.. Thanks..!
Click to expand...
Click to collapse
I don't mean to argue with you here and you are right about research threads, but honestly it's easy to get caught up in frustration with the amount of information. Some authors are good at documentation and some skip steps along the way or extra links are in the threads.
I just switched over to Gullum's Diamond Rom and was I nervous upgrading "Yes" and did I read much that I could "Yes". Were the instructions to HardSPL, Jump were a little unclear "Yes" so people asking questions are legit to a degree but we shouldn't also be eagar to pounce on...
tvos

tvos said:
I don't mean to argue with you here and you are right about research threads, but honestly it's easy to get caught up in frustration with the amount of information. Some authors are good at documentation and some skip steps along the way or extra links are in the threads.
I just switched over to Gullum's Diamond Rom and was I nervous upgrading "Yes" and did I read much that I could "Yes". Were the instructions to HardSPL, Jump were a little unclear "Yes" so people asking questions are legit to a degree but we shouldn't also be eagar to pounce on...
tvos
Click to expand...
Click to collapse
I agree with some of your remarks. Yes myself and others have jumped down people's throats yelling, "Search." One thing you have to remember though this is a developers forum, not a novice forum to help people making there phone look "cool."
Going into flashing / upgrading / modifying, you have to have a little bit of knowledge or time using Windows Mobile / Windows in General devices and machines.
Usually reading some background information can be a world a difference before jumping into this sort of thing.

I found the problem to stuck in bootloader. Thanks to all who have posted threads.
Originally Posted by GSLEON3
Many of you have noticed that in the past I spent a great deal of time helping people with Kaiser issues. Many of you have asked for help in the last few days & are probably feeling ignored. I am just unavailable at this time. My little sister had a Kidney Transplant operation on June 30th, 2008 & I have been spending much time traveling back & forth between my home in California & her's in Arizona. There were a few complications, but she is now doing well & recovering. I will be spending this weekend & most of next week helping to care for her & will be unavailable still for the next ten days or so.
There are many capable people in the Kaiser forum that will help. If you have hit a wall, be patient & I will begin to answer my PM's in the order they were recieved within the next week. Sorry I can't be of more help at the moment, but family comes first as I'm sure you understand.
Thanks,
GSLEON3
Aboslutely man. You go take care of your family. I will pray for God to guide you all through this trying time.
On the Kaiser note, I found after further studying of some threads, a solution to my issue where I was stuck in bootloader. I think this will apply to anyone that is stuck in bootloader with the usb/serial showing at the bottom and when they try to flash a new rom is goes to 100%, but the are still stuck on the boot screen.
After reading more threads, it appeared that there was some sort of disconnect between the usb and the phone. Since my PC was stating that it was successfully completing the flash, that shows that it was not getting any type of error from the phone. After reading a thread I simply blew in my tilt usb port and used my stylus to try to straighten it out as one of your post state to ensure the usb connection is straightor it may give mtty an issue.
Once I messed with my USB port, the phone came back to life and everything was fine. Everything was rebooted and all my info was lost however. I was even able to successfully flash a new ROM.
In closing, if anyone is stuck in bootloader mode and their flash goes to 100% and doesn't fix their issue, tell them to clean and straighten their usb connection.

Solution for Those Stuck in Bootloader
Here is the link to the initial thread I started for my issue
http://forum.xda-developers.com/showthread.php?t=406221
I found after further studying of some threads, a solution to my issue where I was stuck in bootloader. I think this will apply to anyone that is stuck in bootloader with the usb/serial showing at the bottom and when they try to flash a new rom is goes to 100%, but the are still stuck on the boot screen.
After reading more threads, it appeared that there was some sort of disconnect between the usb and the phone. Since my PC was stating that it was successfully completing the flash, that shows that it was not getting any type of error from the phone. After reading a thread I simply blew in my tilt usb port and used my stylus to try to straighten it out as one of your post state to ensure the usb connection is straightor it may give mtty an issue.
Once I messed with my USB port, the phone came back to life and everything was fine. Everything was rebooted and all my info was lost however. I was even able to successfully flash a new ROM.
In closing, if anyone is stuck in bootloader mode and their flash goes to 100% and doesn't fix their issue, tell them to clean and straighten their usb connection.