Database Info

Advanced Shelltool help

Hi everyone. I am in need of assistance with shelltool. I've been flashing ROMs for quite some time and this goes beyond the scope of typical upgrading. I apparently had a bad flash happen and need some help correcting it. The OS appears to work fine, except some applications .cab installers exit before asking device or storage card. I have attempted to load the EnableRapi.cab and Cert_SPCS.cab; however, they exit almost instantly after starting them.
I had this situation happen once before and I was able to oddly enough try to load the original T-Moblie ROM through shelltool (didn't install at all), then try NBD 8.3. which brought me to a boot loader screen after doing a hard reset, but didn't install NBD 8.3. So far I'm not having much luck in recreating the experiment.
Is there a way to force a Wizard into bootloader mode using shelltool or some other utility? I can restore the device if I can get that far.

it's time for my first post
Hi, have been reading this forum for about 3 month and i enyoy it and learn a lot. Have been try about 7 roms and like all. It's time to payback.
Yo can enter bootload by pressing and holding the voice command button and then softreset, keep holding the voice command button util you reach bootload.
Other thing you can do is run the original rom by its executable program not using shelltool.
Good luck

Awesome! That rescued my phone. You saved me quite a bit of time in getting my phone back to a working state. You've more than given back!

Dezl0ck said:
Awesome! That rescued my phone. You saved me quite a bit of time in getting my phone back to a working state. You've more than given back!
Click to expand...
Click to collapse
no problem, that's why we are here for, to help each other

Help, Stuck at multicolor screen. XDA Mini S
Dezl0ck said:
I can restore the device if I can get that far.
Click to expand...
Click to collapse
Please tell me how did you restore your phone? i am flashed touchflo rom to my phone and some how it is stuck to the multicolor screen.
Can you help me out?
Thanking you in anticipation.

1 put phone into bootloader by pressing and holding camera button+reset hole. Keep holding the camera button untill you see the tricollor screen.
2 plug the phone into the computer (wait to hear the noise that it found hardware
3 Flash a rom you know worked (maybe your original/ maybe someone elses... maybe even mine )
4 wait untill the flashing finishes and "Tap Screen..." appeares before unplugging.
(If you have a G4 then I advise you to flash the original rom, or make sure your ipl/spl is propper. check the G4 forum to be sure, or ask Mestrini - The creator of the Wizard service tool. I believe he has a G4 and knows more about it than most)
Happy Flashing

Randomly get Update/Connection errors.
Thank you very much for the response.
Unfortunately, i am still not able to flash the ROM. I did the follwoing steps, can you please help me letting me know, where m i wrong?
I restarted my PC.
I did Reset my PDA, by removing and placing the battery.
then i boot the PDA, it always boots to the TRICOLOR Screen.
afterwards, i tried to flash following ROMs
Xda_Minis_Upgrade_v2.21.4.101.exe [the oringal one, used to be working since long]
SNN_Version_3.0 [i flashed this, some days ago and worked fine for me]
SNN_3.0_FULL_version [the ROM that caused the problem]
BUT no use, i randomly get following errors:
ERROR [262] : UPDATE ERROR
ERROR [274] : CONNECTION
and some other errors.
Pleaaaaaase some one help me.
Thanking you in anticipation.

Radio Help pls!

OK
I've always had troubles flashing radios for some reason, I've managed to just not do it but now with Duttys 6.1 out I really need some help
- I've flashed Duttys latest successfully
- I've flashed HardSPL
- But whenever I flash the radio (1.64.08.21) I get a connection error at 99%!!
Now I can still get into the phone using mtty and the boot command.
Am I doing something stupid -- Any help gratefully received!
Alex
ps - I have a UK o2 XDA Stellar

I'm a newbie been here with a AT&T Tilt less than a week and I promise I'm reading, but I'm having the exact same problem. Flashed Duttys dual V4 as my first try last Tuesday without a problem and of course be a crazy new guy I wanted his newest work. So I flashed Duttys 6.1 today and I guess I just can't figure out how to flash radios, because I've tried 2 now and both error out at 99% and I too have to use mtty to get back into the phone. I'll keep reading, but if someone could tell us new guys what the heck we are doing wrong that would be great.
PS I'm glad to be here and this looks like a lot on fun thanks for having me and look forward to helping out someday.
JMan

Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan

First, are you using a 6.0 rom or a 6.1 rom? If you are using a 6.0 rom you cannot flash any of the 6.1 radios and vice versa. Also, if you have hardspl installed, why would you need to use jumpspl. I have never used jumpspl and I promise I have flashed 50+ times counting, roms, radios and splash screens.

I believe that was my problem, I was never able to get Hard-spl installed and I was using jumpspl to install the 2 roms that I have installed since I got my tilt a week ago. The method I used above allowed me to get hard-spl installed and then I was able to install the radio rom. I am using Duttys WM6.1 rom.

JMan I want your babies!!!
Ok I had actually done everything upto the final step (holding the camera button after a soft reset) but that made it possible to flash the radio just as you described.
So many thanks for sharing your solution!!
Alex

jmandss said:
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
Click to expand...
Click to collapse
You are the STAR! Trillions of thanks. Solve my problem!!!

I love it when when the new guy can help out! Glad it worked guys, and thanks to all the old pros around here for allowing us to read so we can try and help ourselves out.
Take care,
JMan

I think I have fallen in love with this thread. This is truly nice to see guys. Keep up the great work.

i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !

please help me
I don't want to miss mi tytn

pedro_se_rooot said:
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
Click to expand...
Click to collapse
You need to use MTTY to get things going for you again, here is the thread to get mtty:
http://forum.xda-developers.com/showthread.php?t=371154&highlight=mtty
Search around and see if you can find the step by step to use it, might even be a how to text file in the zip file not sure. This should get you back on your way.
Can someone locate the step by step to use mtty for this man and put it in this post?
Have a good one,
JMan
Not a good day for the Wolfpack, Damn Tarheels!!

Help!! Can I Revive My Tornado!!!

Hi. Can someone please help me out? I was trying to flash my cingualr 2125 from wm 5.0 to 6.0. I was using Kar Hoe's instuctions and I used the typhoon instuctions instead of the tornado instuctions. I didn't know there was a difference at the time.
I did all the steps up until step 5 on the typhoons where it states you will get a white screen. At that point, I accidently hit my usb and the phone disconnected from active sync. I thought if I took my battery out, I could just do a reboot and get the reboot screen. Well I got nothing. I cannot even turn the phone one. I cannot even connect to active sync. I thought maybe I fried the battery and bought a new one and no luck. I have done a hard restart and all other things that I could think of.
Does anyone know if I had hurt the phone and if it can be fixed to get to the bootable screen. I would be happy just to get it to power on and stay with wm5 just to have the phone working.
I really appreciate your help.
Khernden69

Aah i remember doing the same once i screwed up my newly acquired tornado with typhone rom. phone was dead no bootup screen nothing, i tried every thing asked everywhere, thankfully i had warranty period so went to them with very innocent face and made up a story that "i switched it at night and it wont boot in the morning" they bought and gave me a new phone after a week. any ways GOOd Luck

Enjoy WM6

think your in trouble mate. Using the wrong rom and cancelling it half way is a big no no. Least you have a fancy paper weight

Similar problem
I have just acquired a tornado (in it's o2 guise) and it will only get as far as the wm splash screen. I thought trying a hard reset or flashing it with a new rom might revive it. However I tried hard reset (holding down the 2 soft keys beneath screen while pressing power button?) but it just kept booting to the splashscreen. The phone doesn't boot far enough to be recognised by Activesync so can't flash it. Can anyone suggest a solution? Would going to bootloader mode allow me to flash it? If so, how do I do that?
Thanks

try this.
1.switch off phone
2. remove battery
3. re install battery
4. hold camera button
5. while holding camera button plug usb cable to port
6. after some second u will see three color bootloder screen
7.format binfs
7. then u can flash correct tornado rom
you can us alternative method for going to bootloder mode
hold camera button while holding camera button press power button(not hold)
GOOD LUCK

Hi fayizk1
Thanks for the tip. Just one question, will this command CID unlock the phone too? It's just the phone isn't CID unlocked, I've tried using instructions and tools on other threads to change the CID value of downloaded roms to that of my phone, but all Typhoonnbftools produces is a 512 byte .nbf file which isn't good for anything. Any suggestions?

binfs not allowed!
When I run format binfs from teratermpro I'm told it's not allowed. What do I do now?

First off, try a couple different times. The "format BINFS" command is case sensitive - where your capital letters are makes ALL the difference. You may need to try a couple times, but I believe "format" is all lowercase and "BINFS" is all capitals.

Thanks djsleepwalker but I tried your suggestion and tried a few times in different cases but still got "Not allowed operation". (If all caps I get "Invalid command") I read somewhere that I'm getting this message because the phone is not CID-unlocked?

Tried a few times in different cases, still get "Not allowed operation". I read somewhere else that I'm getting this message because the phone is not CID-unlocked? Well I know that otherwise I would have just flashed another rom. Problem is I have tried using Typhoonnbftools to change the CID over numerous roms, the file it produces is only 1kb or smaller which is no good for anything. I feel like I'm running out of options...

Just try to flash with a legal WM5 ROM from the magnufacture's web site while the device is in bootloader screen. I hope it will work.
Good luck

This is my problem. There isn't one on their site! I emailed them but they were no help at all.
edit: Have also searched loads of forums etc. no-one seems to have it and there are lots of people looking for o2 roms.

Won't help
timwb said:
This is my problem. There isn't one on their site! I emailed them but they were no help at all.
edit: Have also searched loads of forums etc. no-one seems to have it and there are lots of people looking for o2 roms.
Click to expand...
Click to collapse
Well, I found 'magic' WM5 for SDA, but since it CIM locked, and upgraded to radio 2.0, phone refuse to upgrade (downgrade) to WM5, he said I needed newer file or something... It's stucked in bootloader

I come from China IOICN, but I can not help you, because my bad English.

timwb said:
When I run format binfs from teratermpro I'm told it's not allowed. What do I do now?
Click to expand...
Click to collapse
try first
info 2
then
format BINFS

Still says "Not allowed operation!"

timwb said:
Still says "Not allowed operation!"
Click to expand...
Click to collapse
can you get any information when you try "info 2" command?

Yeah
info 2 displays results ok

I've RESEARCHED, and found no answers. I think it's bricked

Hello to all, I am a noob here and have tried to adhere to all of the demands to do research and not post ?'s, but I am at a wall.
I have a Tilt and I ran the sim unlock and I was using the Sleuth 3.0 on it. Everything was working fine. I added the Iunlock cab and it worked fine as well. I then tried to install the icontacts, but i would have to go to program files and icontacts file in order to use I contacts. Well, wanna be innovative me thinks to try and move that file so it would replace something. I copied it to the windows appbuttons folder and deleted the regular contacts and nothing happened, then I put it in the start up folder and no luck, then I simply copied it to the windows folder not at the bottom where all of the extra files are. After that I tried to reset it and now all that I get is the bootloader screen. it reads as follows:
KAIS1*0 MFG
SPL-1.0.Olipof
CPLD-8
At the bottom, it shows either USB or Serial depending on if the usb is plugges up.
I tried running the sim unlock again and the dutty rom and both load to 100% but it goes back to the same screen. Any help would be greatly appreciated. Please help and thank you so much.

barrnunn said:
Hello to all, I am a noob here and have tried to adhere to all of the demands to do research and not post ?'s, but I am at a wall.
I have a Tilt and I ran the sim unlock and I was using the Sleuth 3.0 on it. Everything was working fine. I added the Iunlock cab and it worked fine as well. I then tried to install the icontacts, but i would have to go to program files and icontacts file in order to use I contacts. Well, wanna be innovative me thinks to try and move that file so it would replace something. I copied it to the windows appbuttons folder and deleted the regular contacts and nothing happened, then I put it in the start up folder and no luck, then I simply copied it to the windows folder not at the bottom where all of the extra files are. After that I tried to reset it and now all that I get is the bootloader screen. it reads as follows:
KAIS1*0 MFG
SPL-1.0.Olipof
CPLD-8
At the bottom, it shows either USB or Serial depending on if the usb is plugges up.
I tried running the sim unlock again and the dutty rom and both load to 100% but it goes back to the same screen. Any help would be greatly appreciated. Please help and thank you so much.
Click to expand...
Click to collapse
You could hard reset if you altered something in WM to cause it not to boot...hopefully

I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?

barrnunn said:
I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?
Click to expand...
Click to collapse
Yeah and then you press send...
- well you could try go into the bootloader and flash an OEM original ROM on i do not believe that doing this would brick your kaiser.

zeezee said:
You could hard reset if you altered something in WM to cause it not to boot...hopefully
Click to expand...
Click to collapse
In case u dont know how to do it:
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Resets

Or else search for MTTY. That helped a lot of ppl who got stuck in boot loader.

barrnunn said:
I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?
Click to expand...
Click to collapse
U need to hold the stylus in the hole longer, untl a message pops up on the page.
If it does not hardreset or help u, do what zeezee told u - flash a new rom.

OK, thank you all for you diligent assistance. I have tried the hard reset and it does the same thing...goes to black for about 2 seconds, then for a very split second goes to a grey screen and flashes loading then back to the bootloader.
I will try a search for the people stuck in bootloader and try flashing a OEM ROM, I will let you know how it goes. Thanks again.

barrnunn said:
OK, thank you all for you diligent assistance. I have tried the hard reset and it does the same thing...goes to black for about 2 seconds, then for a very split second goes to a grey screen and flashes loading then back to the bootloader.
I will try a search for the people stuck in bootloader and try flashing a OEM ROM, I will let you know how it goes. Thanks again.
Click to expand...
Click to collapse
Here is a list of OEM ROMs:http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs

I do not see any Mods here around or somebody yelling (search button is your friend,search the wiki everything is there, bla bla)To having a woman at home change everything.. Thanks..!

Before you try the dangerous MTTY method, you could try refresh a oem rom w/ the SD method

ok, I am flashing an OEM rom now, but what does it mean to do it with the sd method?

barrnunn said:
ok, I am flashing an OEM rom now, but what does it mean to do it with the sd method?
Click to expand...
Click to collapse
From youre sd card (memorycard), look it up in wiki. Moust of us flashaholics keeps oure rom on oure memorycard and just rename the rom/bootsplash/radio or whateva and place it in root then activate bootloader -> flash. This is an alternative for not using usb cable, pc and active sync
http://wiki.xda-developers.com/index.php?pagename=KaiserSDFlash

ok thanks, but am i correct in understanding that to do that I have to use the phone to access the mem card?
My issue is that the only screen I get is bootloader, no nothing else. I can't even turn it off. I can take the battery out to get a black screen, but any action to try something will take it back to the bootloader screen. But for some reason, it still allows me to flash the ROM, I think. I flash it on my pc and then my phone goes to the grey screen where it shows the % of progress. It reaches 100% and the pc tells me to click finished and I do then it goes back to the bootloader.

barrnunn said:
ok thanks, but am i correct in understanding that to do that I have to use the phone to access the mem card?
My issue is that the only screen I get is bootloader, no nothing else. I can't even turn it off. I can take the battery out to get a black screen, but any action to try something will take it back to the bootloader screen. But for some reason, it still allows me to flash the ROM, I think. I flash it on my pc and then my phone goes to the grey screen where it shows the % of progress. It reaches 100% and the pc tells me to click finished and I do then it goes back to the bootloader.
Click to expand...
Click to collapse
put the rom image file on storage card and than power on phone in bootloader. the process will start automatically.

thesire said:
put the rom image file on storage card and than power on phone in bootloader. the process will start automatically.
Click to expand...
Click to collapse
yes, just use a card adapter or something to acess youre card (if you cant connect via active sync) then copy the rom over and follow the steps in wiki. Beeing stuck in the bootloader some times aint the worse place to be stuck

korakesion said:
I do not see any Mods here around or somebody yelling (search button is your friend,search the wiki everything is there, bla bla)To having a woman at home change everything.. Thanks..!
Click to expand...
Click to collapse
I don't mean to argue with you here and you are right about research threads, but honestly it's easy to get caught up in frustration with the amount of information. Some authors are good at documentation and some skip steps along the way or extra links are in the threads.
I just switched over to Gullum's Diamond Rom and was I nervous upgrading "Yes" and did I read much that I could "Yes". Were the instructions to HardSPL, Jump were a little unclear "Yes" so people asking questions are legit to a degree but we shouldn't also be eagar to pounce on...
tvos

tvos said:
I don't mean to argue with you here and you are right about research threads, but honestly it's easy to get caught up in frustration with the amount of information. Some authors are good at documentation and some skip steps along the way or extra links are in the threads.
I just switched over to Gullum's Diamond Rom and was I nervous upgrading "Yes" and did I read much that I could "Yes". Were the instructions to HardSPL, Jump were a little unclear "Yes" so people asking questions are legit to a degree but we shouldn't also be eagar to pounce on...
tvos
Click to expand...
Click to collapse
I agree with some of your remarks. Yes myself and others have jumped down people's throats yelling, "Search." One thing you have to remember though this is a developers forum, not a novice forum to help people making there phone look "cool."
Going into flashing / upgrading / modifying, you have to have a little bit of knowledge or time using Windows Mobile / Windows in General devices and machines.
Usually reading some background information can be a world a difference before jumping into this sort of thing.

I found the problem to stuck in bootloader. Thanks to all who have posted threads.
Originally Posted by GSLEON3
Many of you have noticed that in the past I spent a great deal of time helping people with Kaiser issues. Many of you have asked for help in the last few days & are probably feeling ignored. I am just unavailable at this time. My little sister had a Kidney Transplant operation on June 30th, 2008 & I have been spending much time traveling back & forth between my home in California & her's in Arizona. There were a few complications, but she is now doing well & recovering. I will be spending this weekend & most of next week helping to care for her & will be unavailable still for the next ten days or so.
There are many capable people in the Kaiser forum that will help. If you have hit a wall, be patient & I will begin to answer my PM's in the order they were recieved within the next week. Sorry I can't be of more help at the moment, but family comes first as I'm sure you understand.
Thanks,
GSLEON3
Aboslutely man. You go take care of your family. I will pray for God to guide you all through this trying time.
On the Kaiser note, I found after further studying of some threads, a solution to my issue where I was stuck in bootloader. I think this will apply to anyone that is stuck in bootloader with the usb/serial showing at the bottom and when they try to flash a new rom is goes to 100%, but the are still stuck on the boot screen.
After reading more threads, it appeared that there was some sort of disconnect between the usb and the phone. Since my PC was stating that it was successfully completing the flash, that shows that it was not getting any type of error from the phone. After reading a thread I simply blew in my tilt usb port and used my stylus to try to straighten it out as one of your post state to ensure the usb connection is straightor it may give mtty an issue.
Once I messed with my USB port, the phone came back to life and everything was fine. Everything was rebooted and all my info was lost however. I was even able to successfully flash a new ROM.
In closing, if anyone is stuck in bootloader mode and their flash goes to 100% and doesn't fix their issue, tell them to clean and straighten their usb connection.

Solution for Those Stuck in Bootloader
Here is the link to the initial thread I started for my issue
http://forum.xda-developers.com/showthread.php?t=406221
I found after further studying of some threads, a solution to my issue where I was stuck in bootloader. I think this will apply to anyone that is stuck in bootloader with the usb/serial showing at the bottom and when they try to flash a new rom is goes to 100%, but the are still stuck on the boot screen.
After reading more threads, it appeared that there was some sort of disconnect between the usb and the phone. Since my PC was stating that it was successfully completing the flash, that shows that it was not getting any type of error from the phone. After reading a thread I simply blew in my tilt usb port and used my stylus to try to straighten it out as one of your post state to ensure the usb connection is straightor it may give mtty an issue.
Once I messed with my USB port, the phone came back to life and everything was fine. Everything was rebooted and all my info was lost however. I was even able to successfully flash a new ROM.
In closing, if anyone is stuck in bootloader mode and their flash goes to 100% and doesn't fix their issue, tell them to clean and straighten their usb connection.

Stuck in Bootloader (I've searched)

I don't mean to create another unnecessary bootloader thread, but I've literally spent 10+ hours searching and trying different things and cannot get my phone to stop messing up.
It happens when I restart and not every time. Sometimes it'll restart fine, but other times it'll get stuck in bootloader mode and will only restart when plugged into a computer.
I've reflashed the rom with several different ATT roms. I've installed several different version of SPLs and hardSPLs. I've done hard resets, soft resets, resets that are slightly above mild!
I have tried doing some of the MTTY things, but no matter what I do, I can't seem to get MTTY to recognize the USB port. I've deselected the USB option from connections, neither of the rapimgr.exe or wcescomm.exe files are shown in my processes tab of task manager (although they do show up in the services tab and I keep going to the services thing and stopping them). I have the phone in bootloader mode, it shows serial, I plug it in to the computer and it displays usb, but then I can't get MTTY to recognize it. I have both versions 1.16 and 1.42.
I'm at my wit's end with this thing. I had it back to its factory settings, but have since installed HardSPL (I think, I'm getting lost).
When I start it up with it plugged in, it displays the following during ATT logo:
R: 1.65.20.29
G: 25.88.40.04H
D: 3.55.00.00
When it's in bootloader, it says Serial and displays this:
Kais1*0 MFG
SPL-1.0.OliPof
CPLD-8
Please let me know when I need to try. I have no idea why I can't get the MTTY thing to work. I've tried everything I can think of to get it going.
Anyway, again, sorry if it's redundant, but I'm sick of this thing. BTW, is this a warrantable issue? I'm nearing my warranty end, but don't want to send it in and have them charge me $450 for a new phone again (like they did last time I sent it in for warranty issues when the screen went bad).
THANKS,
Matt

Have you read this thread: http://forum.xda-developers.com/showthread.php?t=433835 ?
follow those instructions, you do have a hardSPL, but not a good one.
try flashing the Hardspl3.29 via MicroSD as is explained in that thread.
after that flash any wm6.1 radio aand normal rom you want.
try the radio rom in my sig

Please read the stickies
Hi:
Please check the two stickies on the top of the forum to find solutions to your problem and read solutions that have been tried by other users.
Link to the stickies:
Kaiser intermittently stuck in SPL? - Possible solution and prevention!: http://forum.xda-developers.com/showthread.php?t=420683
Kaiser Stuck at Bootloader
http://forum.xda-developers.com/showthread.php?t=423486
Hope this helps. Thread closed.