ROm update question - 8125, K-JAM, P4300, MDA Vario ROM Development

I can't connect my phone through activesync but I heard that u can update ur rom from ur mini sd card. I already download a rom to my sd card but wat do I do now. how do I upgrade through the mini sd

download the wizard service manual. I believe it is on the wiki. I will also include that in my next release. but if you cant wait untill then, search for it.
you can also put the phone in bootloader mode by pressing camera and reset buttons. keep holding the camera button untill you see the tri collor screen and connect the usb cable. run the update utility. You may need activesync installed on your computer to make sure that the drivers are loaded.

Related

wizard g3 stuck in bootloader screen

hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
hehh
same happend to me once. Go online and finde botton run , update utility 2.00.1
go step by step:
Disconnect your phone from the usb cable,disable any Firewall and Anti virus and reboot your Pc.
1. Make sure your phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t Bluetooth for the Upgrade)
4. When you see usb appear at the bottom of bootloader screen
5. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
After then, install origial ROM. (u can try T-Mobile MDA Software Version (2.26.10.2) )
Let me know if it's working
ty man for ur reply , i have tried every possible solution, including mtty! no luck. from ur post i didnt understand the following
Go online and find botton run , update utility 2.00.1
Click to expand...
Click to collapse
did u mean button rom . if yes , what the 'update utility 2.00.1' ?
ty
can i use mtty to revive my phone? i found some command for erasing my entire rom in the phone , but it doesnt seem to work . help me

help in changing rom after duttys v4rtm

I have flashed dutty's v4 rom and i want to change it
the problem is that when i try to do so i run
KaiserCustomRUU
my device goes into the 4 stripes screen it says usb
but then the program in the pc says error 260 and doesn't load the new rom
my phone still works as dutty's rom is still in but what can i do to change it?
Thank you and i have searched a lot but could not find a solution
thimiost said:
I have flashed dutty's v4 rom and i want to change it
the problem is that when i try to do so i run
KaiserCustomRUU
my device goes into the 4 stripes screen it says usb
but then the program in the pc says error 260 and doesn't load the new rom
my phone still works as dutty's rom is still in but what can i do to change it?
Thank you and i have searched a lot but could not find a solution
Click to expand...
Click to collapse
OK lets start at the basics...... In bootloader mode (tricolour screen) what text does it say at top of the screen?
Have you DEFINITELY Sim Unlocked and CID unlocked?
it says these things
kais130 mfg
spl-10.0.Olipof
cpld-8
Ok that confirms you have the capability to flash. I have seen in the past some people have managed to flash one time only using jumpspl but then their device reverts back to original bootloader...I was one of those people
Next question then...Can you boot the phone normally and gain an activsync connection to it?
yes
i can use my phone normally
only i cannot put a new image in
Are you using Xp or vista? If using vista it may be worth trying a reboot... sometimes it goes doolally with its usb ports. If you cannot see the phone through WMDC or activsync after a reboot it is worth going to SYSTEM (on your PC) viewing non present devices through device manager,( Drop to Command prompt and type... Devmgmt.msc set DEVMGR_SHOW_NONPRESENT_DEVICES=1 ) removing the relevant phone connection and then re attaching it so that windows re detects it.
If you can get a connection via actvisync (win XP) or WMDC (vista) to your phone then all should be ok. Uncheck the activesync/ WMDC "allow USB connections" and try again.
If this still doesn't work then search around here for MTTY. That will allow you to specify the usb connection to the device...amongst other things.
thank you for your time
i have win xp and activesync works nice
the problem is when bootloader starts
When you attempt flashing, do you do it from the device already booted into windows mobile or direct from bootloader?
Which ever way you have tried it, try ther other way.
Not teaching you to suck eggs but just in case you dont know.... To get direct to bootloader hold camera button and soft reset with stylus whilst holding camera button down and the tri colour screen should appear.
With device at the bootloader screen, Can you confirm that you hear the windows "noise" when you unplug and re plug the USB cable just as you would when plugging and unplugging the device normally. This will determine if the device has connection at the bootlaoder stage.
why not just flash using the microsd card. its much easier that way
yes it has connection
the thing is that i have already flashed as i told before with dutty's v4
now i can't
Usually Error 260's are related to the USB port functionality ( Port can't be opened etc).
The SD card method or MTTY should sort you out.
thx again
hope it works
at least the sd trick worked!!!!
now running on winmob 6.1
Glad to hear you sorted it.
almost
i cannot use my sd card cause i have to have it formated in order to put a new rom in
thimiost said:
i cannot use my sd card cause i have to have it formated in order to put a new rom in
Click to expand...
Click to collapse
disable USB connections in ActiveSync and flash.
This Link gives a list of eror codes for Hermes, and probably the same for Kaiser.
It's likely that you have a USB port error - maybe try changing the USB port you use or a different sync cable - or just stick to SD card flashing in the future - I keep an old 1gig card for this.
this IS the problem...i cannot flash...
it stays in the bootloader with the message i wrote
thimiost said:
it stays in the bootloader with the message i wrote
Click to expand...
Click to collapse
It happen to me before hardspl again fix it, not sure why
you mean use the sd method to do hardspl again?
OHHH lord dutty we need your new rom

Flashing rom without Activesync

Hi all,
How to flash the rom for a Wizard G4 without activesync (only with the bootloader mode)??
I had and error with my previous update and i need to re-install it in bootloader mode...
Thanks in advance,
TD.
Simply,get the phone in Bootloaders by pressing Camera + soft reset,it'll go into Bootloaders (RGB) and hook up the phone with pc via usb cable,watch small usb appear at the bottom of the Bootloader Screen,if its there just run the RUU in the rom,it'll start to flash.
zabardast_1 said:
Simply,get the phone in Bootloaders by pressing Camera + soft reset,it'll go into Bootloaders (RGB) and hook up the phone with pc via usb cable,watch small usb appear at the bottom of the Bootloader Screen,if its there just run the RUU in the rom,it'll start to flash.
Click to expand...
Click to collapse
No, Its comm manager + camara + softreset...........
Don't work
Yes, my Wizard is in bootloader mode (the usb indicator is here), but when I run the RUU, no device is detected (it's normal because RUU needs activesync connection) !!! Same effect with the official ROM !!
Please help...
for your information, when my it re-boot it is blocked on:
IPL 2.17.0001
SPL 2.17.0001
GSM 02.07.10
OS 6.1.0.0
Thx,
TD.
erm i always press the camera button and softreset and it gives me a RGB
zabardast_1 said:
Simply,get the phone in Bootloaders by pressing Camera + soft reset,it'll go into Bootloaders (RGB) and hook up the phone with pc via usb cable,watch small usb appear at the bottom of the Bootloader Screen,if its there just run the RUU in the rom,it'll start to flash.
Click to expand...
Click to collapse
yes it works !
Perhaps...
Perhaps you can try the sd card method, but one of the guru's here would have to confirm that. When my usb was busted, that method was suggested to me (click the link in my siggy). I don't have a G4, so I am not sure if the sd method would even work, but it is worth a read, and like I said, perhaps one of the guru's could confirm or deny this method.
SD Card
How to flash with SD? Do you have a link to do this?
Thx,
TD.
hello everyone!
Untill a few minutes ago I had a similar struggle; my Activesync connection was down exactly when I wanted to flash my device; I read all what was readable and after trying to flash tie new rom from the card, i just realised that if i press the usb cable firmly into a direction, the device suddently got recognised. SO, i guess that too much use of the usb port gets electrical contacts to get loose.

[Q] please help flashing rom via usb

trying to flash my fuze windows 6.1 to exquisite v4.24 and when i go though the steps and get to where its at zero percent and my phone restarts to the red green blue screen it disconnects from the pc and stops the flashing..can anyone please help would appreciate it alot.
none?
does noone have a answer? please let me know how to fix this or what im doing wrong..tried microsd way and it just freezes on loading
Aside from making sure you are flashing the right ROM toy our device, no idea as to what the problem is. Make sure you have a GSM ROM if you are flashing a GSM device or a CDMA ROM for a CDMA device.
Additionally, the way I usually flash is I remove the battery, SIM and microSD. Then I connect the cable to the computer and while I hold the volume down key, I connect the cable to the device and I see the multi-color screen. From there, I run the executable file to flash the device. I have an at&t Fuze, which is a GSM device. I have the ROM in my sig/signature flashed to my device.
I had a similar problem and what I did was I uninstalled and then reinstalled windows mobile device center. Dont know if that will help...
dont work
my computer wont reconize it when its at the 3 color screen....is there anything i should do before i try to flash like anything i need to have on my device for it to work?
To flash ones device(if GSM)
This is what "I" do each time when I flash a custom ROM:
Remove the battery, SIM and microSD
(Using a working USB cable)I connect the USB cable to my device
(Using a working USB port and computer)I hold the device's volume down key while I connect the USB cable to the computer
Run the flashing utility of choice
NOTE If this is the first time you've connected your device in this manner, your computer should detect a new device. If it doesn't then this falls outside of my knowledge as it is difficult for me to troubleshoot your computer from my end. ​
You could also try to put your nbh file in the root of your SD card, make sure it is named RAPHIMG.NBH, then when you enter bootloader mode the bootloader itself will look for it and try to flash it. It may not be a permanent solution, but it should work.

[Q] [URGENT] USB Issues

So, i had my phone with the MIUI rom but i wasn't really liking because it was a little slow, so i flashed Kyrillos 9.5
After i flashed Kyrillos 9.5 i start having some battery issues, i was thinking that it was some problem of the ROM so i went away to flash another ROM, but ODIN didn't detected my phone, i upgraded the drivers and nothing.
My last try was to flash a rom by the update.zip method.
It didn't ended well and now i can't use the phone at all, it just stucks at bootloading.
If someone can help me to get my phone working again it would really help because i can't even use it.
PS: Sorry for my english.
Try to write another ROM on your sdcard(for example CM7a8.1) and install it from recovery
DoR2 said:
Try to write another ROM on your sdcard(for example CM7a8.1) and install it from recovery
Click to expand...
Click to collapse
Yeah, take your Micro SD out and put another update.zip on it. Then go into recovery hold Volume Up+Volume Down+Home and Power. Flash ROM and hopefully it'll work
Trying changing USB ports or rebooting your pc
Cheers
Sent from my GT-i9003 powered by Stable and Smooth CyanogenMod 9!
follow bscrazes advice, try other usb ports and then reboot your pc and try again, if that doesnt work still;
enter recoverymode (hold down both volume keys, power button and center button) then go to mounts and storage and choose usb mass storage device.
then plug it into your computer, it should just recognise it as a mass storage device, from here open folders and place a good update zip on it. suggested cm7a8.1
then apply update from zip.
this should work,
if you get errors doing this reply here and we shall try help
you need to re-install the driver....
J.Purungrit said:
you need to re-install the driver....
Click to expand...
Click to collapse
I agree
Sent from my GT-I5800 using xda premium
Though I'm giving the advice a bit late try the following
first uninstall all samsung stuff (even drivers) from your computer.
Then as Jason-EX said install usb drivers for samsung mobile
If you are unable to get to recovery try the following:
When the phone is powered off press power,volume down and home button simultaneously (now you should directly enter download mode)
connect it to computer now odin will recognise your phone
Flash some stable rom or kernel
I had the same problem once and this procedure worked
For the driver - http://drivers.softpedia.com/get/MOBILES/Samsung/SAMSUNG-USB-Driver-1480.shtml (if at all windows doesn't download it)
if u hav all the drivers installed and still ur phone cant b detected in download mode ...den u gotta usb problm buddy...try changing the usb cable or try in different ports ...that might work.

Categories

Resources