Related
Hi everyone. I am in need of assistance with shelltool. I've been flashing ROMs for quite some time and this goes beyond the scope of typical upgrading. I apparently had a bad flash happen and need some help correcting it. The OS appears to work fine, except some applications .cab installers exit before asking device or storage card. I have attempted to load the EnableRapi.cab and Cert_SPCS.cab; however, they exit almost instantly after starting them.
I had this situation happen once before and I was able to oddly enough try to load the original T-Moblie ROM through shelltool (didn't install at all), then try NBD 8.3. which brought me to a boot loader screen after doing a hard reset, but didn't install NBD 8.3. So far I'm not having much luck in recreating the experiment.
Is there a way to force a Wizard into bootloader mode using shelltool or some other utility? I can restore the device if I can get that far.
it's time for my first post
Hi, have been reading this forum for about 3 month and i enyoy it and learn a lot. Have been try about 7 roms and like all. It's time to payback.
Yo can enter bootload by pressing and holding the voice command button and then softreset, keep holding the voice command button util you reach bootload.
Other thing you can do is run the original rom by its executable program not using shelltool.
Good luck
Awesome! That rescued my phone. You saved me quite a bit of time in getting my phone back to a working state. You've more than given back!
Dezl0ck said:
Awesome! That rescued my phone. You saved me quite a bit of time in getting my phone back to a working state. You've more than given back!
Click to expand...
Click to collapse
no problem, that's why we are here for, to help each other
Help, Stuck at multicolor screen. XDA Mini S
Dezl0ck said:
I can restore the device if I can get that far.
Click to expand...
Click to collapse
Please tell me how did you restore your phone? i am flashed touchflo rom to my phone and some how it is stuck to the multicolor screen.
Can you help me out?
Thanking you in anticipation.
1 put phone into bootloader by pressing and holding camera button+reset hole. Keep holding the camera button untill you see the tricollor screen.
2 plug the phone into the computer (wait to hear the noise that it found hardware
3 Flash a rom you know worked (maybe your original/ maybe someone elses... maybe even mine )
4 wait untill the flashing finishes and "Tap Screen..." appeares before unplugging.
(If you have a G4 then I advise you to flash the original rom, or make sure your ipl/spl is propper. check the G4 forum to be sure, or ask Mestrini - The creator of the Wizard service tool. I believe he has a G4 and knows more about it than most)
Happy Flashing
Randomly get Update/Connection errors.
Thank you very much for the response.
Unfortunately, i am still not able to flash the ROM. I did the follwoing steps, can you please help me letting me know, where m i wrong?
I restarted my PC.
I did Reset my PDA, by removing and placing the battery.
then i boot the PDA, it always boots to the TRICOLOR Screen.
afterwards, i tried to flash following ROMs
Xda_Minis_Upgrade_v2.21.4.101.exe [the oringal one, used to be working since long]
SNN_Version_3.0 [i flashed this, some days ago and worked fine for me]
SNN_3.0_FULL_version [the ROM that caused the problem]
BUT no use, i randomly get following errors:
ERROR [262] : UPDATE ERROR
ERROR [274] : CONNECTION
and some other errors.
Pleaaaaaase some one help me.
Thanking you in anticipation.
Any Help Appreciated. Anyone ever seen this type of "Brick"?
After flashing a new ROM (Tilt XDA-Live v1.0 - fully flashed to 100% and said finished), the device won't boot. It just gets stuck in an endless loop. It trys to boot, shows the AT&T screen, then reboots/resets back to the beginning before getting to the Windows mobile screen.
The only way to get it to stop the loop is to pull out the battery. Put the battery back in and power on and you get the loop again.
I have loaded HARD SPL (1.0.OliPof).
I can get into Bootloader mode by pressing power/camera then reset.
In this mode, I can get it to reflash the ROM (and even other ROMS) but it still ends up in the same loop.
I have tried flashing the Official ATT WWE ROM from this thread but it still loops at boot.
I did the "original/problematic" flash using Vista. Could that be the issue? I have done subsequent "recovery" flashing using XP to no avail.
I have flashed several ROMs to my Tilt in the past (Mostly Dutty ROMs).
I had a Hermes before and flashed that a million times no issue so I'm not a complete noob.
Any ideas? I'm stuck with a brick!
Thanks in advance.
I'm in the same boat. I've flashed over and over (with different ROMs) and am still stuck. But I did every flash from MicroSD card. Did you get any help?
No input yet.
What ROM did you flash that started the problem for you?
dutty's touchflo rom beta for the tilt. i was on dutty's hybrid rom version 3. after flashing the OEM at&t ROM, i'm out of ideas. stay in touch if you find a fix. i'll keep searching.
- J
Bump...
Anyone else seen the issue with a Tilt stuck in a "boot loop" after flashing (see first post)?
Paypal reward for anyone who helps me recover - otherwise I'm going to have to go buy another Tilt (which I could live with but worse yet, I may be stuck with the stock ROM because I'm too gunshy to go back to my flashing ways)
Tried all day to find a fix. Think I made things worse. Read up on some threads using the mtty tool and ran a command (task 2a) that cleared the flash. But now it doesn't even boot to a splash screen, and I can't get back to bootloader mode.
This might sound a bit stupid, but I have taken note that my device upon flashing the new at&t rom actually held some of the information, you would think that a hard reset is performed after a rom flash, but that just wasn't how it worked out for me, anyway I had a radio that wouldn't come up, but would after a hard reset, this was directly after flashing my tilt...
?Glitch
Glitch,
Yeah, I have heard in several places that you need to hard reset after a flash to clear out all the settings from the old ROM. Seems odd since you just overwrote ROM - I think of it as a format (HDD mindset) but I guess it's not a clean format.
Jerich007,
Sorry to hear you went backwards. I stopped flashing my Tilt for the same reason - worried about getting farther in the hole without some expert advice. My next step was to try the MTTY tool just as you noted. Guess I'll go that route as a last resort. If it's any consolation, I seem to remember reading about plenty of people recovering from a "brick" that won’t go into bootloader mode.
Hopefully someone trolling the waters will see this thread and take up the offer for a Cash Reward (Paypal) for help recovering this Brick!
ill put up some paypal $$ for a fix as well. i'm at the end of my rope on this one. i'm subscribed to some other threads so hopefully we'll get some feedback.
It is not so serious as you think! Try the following way:
1- Download the original rom from AT&T (the 1st rom was installed on your device)
2- Turn your bricked Tilt to bootloader ( http://wiki.xda-developers.com/index.php?pagename=Kaiser_Resets )
3- Start flashing your Tilt with the above AT&T rom.
Evething should be OK after that! (but your device need to be installed Hard-SSPL before!!!)
try...
try this link
http://forum.xda-developers.com/showthread.php?t=286755
and maybe these
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
http://forum.xda-developers.com/showthread.php?t=334693&highlight=how+to+unbrick
http://forum.xda-developers.com/showthread.php?t=344402&highlight=how+to+unbrick
don't forget that some of this info isn't for the tilt...
good luck, and be careful
This ROM solved my issues
try this thread
http://forum.xda-developers.com/showthread.php?t=327482
and DEFINETLY download the ROM, flash it. Once it's flashed,then ya can reflash any ROM ya want. Get the newest stock ROM from the sticky and reflash it (if ya want the ATT ROM)
That will fix it.
(I reflashed Tilt XDA-Live v 1.0, and it's working GREAT.)
I did the same thing to my Tilt.
That ROM saved me.
Alemaker
Problem is I can't get to a bootloader screen now. I press Camera+Power+reset, but all that happens is the green LED goes off then on, and then the screen is blank. Anyone know any other tricks? I think I may have erased my bootloader using mtty command 'task 2a'.
...
Hate to say it, but if after hours of searching on the forum you can't find an answer, i'd pm a pro like pof. I don't know if that will work, but their advice is the only thing i'd listen to.
Don't forget to give a lot of detail and maybe mention what you've tried.
Thanks. I've already PM'd pof and olipro. Hopefully they can come up with something.
jerich007 said:
Problem is I can't get to a bootloader screen now. I press Camera+Power+reset, but all that happens is the green LED goes off then on, and then the screen is blank. Anyone know any other tricks? I think I may have erased my bootloader using mtty command 'task 2a'.
Click to expand...
Click to collapse
****, I should have replied after someone posted all those links to Hermes unbrick procedures, to never do a task 2a from hardSPL. It reformats entire flash including SPL and the problem with hardSPL is that you can't flash another SPL, even if you would have tried before rebooting
Anyhow, your only chances to unbrick your device are to try to enter radio bootloader (there is a radio bootloader running on the mARM (ARM9)) and then to flash it. However, only service centres have such flashx utilities I'm afraid. Furthermore I'm not sure if radio bootloader can be entered directly, usually you can enter it via the normal CE SPL. You can try to first connect USB and then press reset with the stylus while holding the Voicecmd key. If you are in XP, then three new devices should be found (composite USB, a modem and a diagnostics port). Download the Motorola "Q" usb drivers, these will work just fine. In this mode you will have to authenticate to the radio bootloader before you can start entering commands. We'll get to that if you manage to connect. Your other chance to unbrick is via JTAG. I know the kaiser has JTAG points scattered on PCB.
Ok, thanks, I'll search for those drivers and let you know. By Voicecmd key do you mean the push-to-talk key along the side or the talk key with the green phoneset icon?
The top button at the left hand side
Ok here's what happens:
1. downloaded Motorola USB drivers (32-bit) from their site, installed and rebooted.
2. plugged in Tilt via usb cable, 'found new Hardware wizard' starts.
3. clicked next to auto-search for drivers, but the wizard fails with 'cannot install this hardware' message. I have 3 yellow question marks in Device Manager for 'Data Interface' devices.
4. held down Push-to-talk button and hit soft reset. No change, no leds are lit, screen is off.
Did I grab the right drivers?
Not bad at all. Apparently your phone is in Qualcomm DIAG mode, probably as a consequence of task 2a Now you can forget about rebooting with Voicecmd pressed.
Either you've got the wrong drivers or you don't install them in the correct way. Go in device manager, right click one of the 3 and update driver, then 'install from a list or specific location (Advanced)', then check 'Include this location in search' and enter the driver path. I'll take a quick look if I can find the drivers for you, I vaguely remember they were on mobile-files dot com.
EDIT: found the drivers, attached. The VID and PID of the found usb devices should be VID_05C6&PID_6000. Take a look in the device's advanced tab in device manager.
PS: Although diagnostics mode sounds great, I haven't yet found a way to flash the device. Perhaps it works with that Hermes radio flasher MaUpgrade_NoID.exe
Guys with a working SPL can enter radio bootloader DIAG mode via "rtask b", exit MTTY and install drivers. It would be great to know if someone has a htc/qualcomm radio flash utility (perhaps MaUpgrade_NoID.exe is what you need)
Hi,
and this is not the right way to start a thread in a new forum
a few days ago i bought a used TytnII with english ROM and last night I decided to organize my phone with tools and programms and then a bad thing happened....
I accidentally flashed a ROM in my phone, the file was marked HTC_TYTNII_UPDATES. The file was installed without giving any warning about ROM or non-compatibility issues. After rebooting i get a message that i used illegal ROM and a DeviceLocked message. and the phone reboots.
Any hope to bring it back to normal?
Stergios
Was it a cab file you installed?
Or did you run the file from your computer while your phone was connected through activesync?
StergiosKLM said:
I accidentally flashed a ROM in my phone, the file was marked HTC_TYTNII_UPDATES. The file was installed without giving any warning about ROM or non-compatibility issues. After rebooting i get a message that i used illegal ROM and a DeviceLocked message.
Click to expand...
Click to collapse
1. I don't think you flashed a rom.
2. There is no illegal rom.
3. Maybe it is a good idea to do a clean rom install on your Kaiser, especially since it is a SH device.
Either install cmonex' hard2 spl (3.29 for Kaiser or 3.56 for Tilt) and any rom of your choice, or flash the official rom for your device which will probably work with any spl you may have.
dani31 said:
1. I don't think you flashed a rom.
2. There is no illegal rom.
3. Maybe it is a good idea to do a clean rom install on your Kaiser, especially since it is a SH device.
Either install cmonex' hard2 spl (3.29 for Kaiser or 3.56 for Tilt) and any rom of your choice, or flash the official rom for your device which will probably work with any spl you may have.
Click to expand...
Click to collapse
loooool
why do you hate your kaiser!
anyways, there is no way a rom got installed without you knowing stergiosKLM...you would get many steps to click on if you were installing a rom.
format the device...install hard spl (whatever kind except 1.0) and flash your custom rom
StergiosKLM said:
Hi,
and this is not the right way to start a thread in a new forum
a few days ago i bought a used TytnII with english ROM and last night I decided to organize my phone with tools and programms and then a bad thing happened....
I accidentally flashed a ROM in my phone, the file was marked HTC_TYTNII_UPDATES. The file was installed without giving any warning about ROM or non-compatibility issues. After rebooting i get a message that i used illegal ROM and a DeviceLocked message. and the phone reboots.
Any hope to bring it back to normal?
Stergios
Click to expand...
Click to collapse
Your best bet is to do a hard reset. Go to start, settings, system, clear storage.
Write 1234 and press yes. It will start you from scratch. That should help.
anyway you could upload the file you installed so we could take a look at it
I am on trip right now but as soon as i get back I will send the file.
Thank you all
Problem update
my kaiser has eng version and the file i executed from my pc and installed in kaiser memory (not card), is a localization program from the Greek distributor of HTC that installs two programs, the first in the localization program and the second is a lock program.
After a hard reset (soft keys and reset key), i get the screen alignment, time and date etc, then i tap the screen to start using the device. and then ii installing the customization program.
the file is "HTC_TyTN_II-0.4.2.6GR-9.0.0.25.Installer.zip" and is a RUU_ExtendedPKG program....
Try hard reset by poking the soft reset hole and hold two softkey simultaniously...
look here for proper instruction to reset (kaiser wiki)...
Hard reset.
tugas2khas said:
Try hard reset by poking the soft reset hole and hold two softkey simultaniously...
look here for proper instruction to reset (kaiser wiki)...
Click to expand...
Click to collapse
This is the best idea I read in the thread. Just think about if this poor person throught that he/she had flashed a rom. Why even send them though the confusion of (hard spl, and flashing a custom rom)when he/she has no idea on what they are doing anyway. Just hard reset your device and this will fix your issue plain and simple.
i already tried that. plus, i do not know how, the device booted, i uninstalled both programs, then did a reset and still it keeps autoruning the file.
Should i record a video so you get an idea of what is happening? How can i upload the file so someone can check it out?
BTW i am a he. 8)
StergiosKLM said:
i already tried that. plus, i do not know how, the device booted, i uninstalled both programs, then did a reset and still it keeps autoruning the file.
Should i record a video so you get an idea of what is happening? How can i upload the file so someone can check it out?
BTW i am a he. 8)
Click to expand...
Click to collapse
You try to hard reset you phone?? I not talking about a soft reset. To perform a hard reset hold down to 2 line keys located between the send call and end call buttons and press and hold in the reset button with your stylist(this is located right next to the charge/usb port) til you see a white screen with blue writing and fellow the on screen instructions. I hope that this helps
i did that many times. all goes well up to the point where i get the message "setup is complete. tap the screen to begin using your device". I tap the screen and I get a windowed message "customization. It will automatically customize your device in 3 seconds" and the device shows a progress bar which says "Loading...." then "Loading AutoShortcut...." then "Installing...." after it finishes it reboots and it loads with the greek customization. as soon as it loads i get another windowed message which notes "DeviceLock. you have illegaly aquiered this ROM! This ROM is only for phones sold by ACE-Hellas and their distribution channel!" and after 3 seconds the device reboots and it keeps doing that.
The best solution is to go to HTC's website and download a new ROM/Radio directly from them. This will 100% fix your problem.
This should be what you need.... Pick one that matches your area/carrier
How to solve until you get home
StergiosKLM said:
i did that many times. all goes well up to the point where i get the message "setup is complete. tap the screen to begin using your device". I tap the screen and I get a windowed message "customization. It will automatically customize your device in 3 seconds" and the device shows a progress bar which says "Loading...." then "Loading AutoShortcut...." then "Installing...." after it finishes it reboots and it loads with the greek customization. as soon as it loads i get another windowed message which notes "DeviceLock. you have illegaly aquiered this ROM! This ROM is only for phones sold by ACE-Hellas and their distribution channel!" and after 3 seconds the device reboots and it keeps doing that.
Click to expand...
Click to collapse
Ok here's the deal. Do a hard reset and when it flashes to the customizing in 3 seconds button, do a soft reset by pushing in the reset button. That will stop customization from happening. Then you can use your phone, but will have to run connection manager to get your connection settings. This is the way to stop customization from running. It only runs one time after a hard reset.
When you get back off your trip, start with the thread mentioned above and work your way through the hardspl process and select a rom that you think has what you want then flash it.
parleyp said:
Ok here's the deal. Do a hard reset and when it flashes to the customizing in 3 seconds button, do a soft reset by pushing in the reset button. That will stop customization from happening. Then you can use your phone, but will have to run connection manager to get your connection settings. This is the way to stop customization from running. It only runs one time after a hard reset.
When you get back off your trip, start with the thread mentioned above and work your way through the hardspl process and select a rom that you think has what you want then flash it.
Click to expand...
Click to collapse
thank you, i appreciate that. One last question for the proper rom, i have to match rom version and radio version only, right?
have a happy new year. thank you all again
HardSPL must be matched too, but you probably won't have any problems regarding this if you install HardSPL 3.29.
victorpak said:
HardSPL must be matched too, but you probably won't have any problems regarding this if you install HardSPL 3.29.
Click to expand...
Click to collapse
spl3.28.0000, it shows in the 3color screen, i d/l this file Kaiser-HardSPL-3.28.zip. I suppose is right.
StergiosKLM said:
spl3.28.0000, it shows in the 3color screen, i d/l this file Kaiser-HardSPL-3.28.zip. I suppose is right.
Click to expand...
Click to collapse
That should work with most custom roms out there. If you have a freeze issue where the screen momentarily freezes, then you will need to flash a different hard spl. Most roms, tell you which hardspl and radio are compatible.
I'm new in the world of flashing cooked ROMs
and i need to do it but i can't
Everytime i try to Flash HARDSPL 3.xx, it stops at the percentage screen and gives me an error on my pc.
And i tried to flash the ROM directly, and same problem.
I'm getting nervous of this stupid mobile, please i need Help.
I read all posts on how to install everything but nothing completed to the end.
bebo833 said:
I'm new in the world of flashing cooked ROMs
and i need to do it but i can't
Everytime i try to Flash HARDSPL 3.xx, it stops at the percentage screen and gives me an error on my pc.
And i tried to flash the ROM directly, and same problem.
I'm getting nervous of this stupid mobile, please i need Help.
I read all posts on how to install everything but nothing completed to the end.
Click to expand...
Click to collapse
you should go here ...
I had a problem when I first did mine. at the tri-color screen my phone never said USB on it and my computer showed an unknown usb device. Here's what worked for me but remember you only need to do this the first time, Once you have HardSPL flashed your phone will work like normal.
after your phone gives you a warning that a program is going to reboot it. You get a tri-color screen. As soon as you see this screen hold the camera and power button and press the reset button, don't disconnect the usb cable.
In other words the program that causes your phone to reboot doesn't allow the usb to work properly but a manual reboot into the SPL using the camera/power button does. I have not tried the "Forced USB" version of HardSPL because this problem goes away once you get HardSPL installed.
This would be better posted in the HardSPL thread.
Flash an official stock ROM, then follow ALL the instructions in the link deepthroat gave you to the T.
I cannot activate my TP2 with EnergyROM. The data won't provision at all.
I cannot run the stock RUU either.
I took the phone to my good friend, and he hasnt been able to do anything with it either...
What am I doing wrong?
Everytime I try to put the stock rom back, I get a different error message.
Has anyone had this issue?
Does phone and sms work? What error do you get for the Data??
I have had problems provisioning data before and there were a couple solutions:
Data Call Failure Error 11 PPP Connection Error - Install stock ROM, call programming (#228 on verizon). If that doesn't work, call verizion and let them know you have no data. If all else fails ask for a DMU reset (although they are reluctant to do this).
What error message do you get when you try to install a stock ROM?
sorry, I have Sprint (shouldve mentioned that)
I get error #777 from data
and I got errors 206, 320, and another 200level one my boyfriend got when he tried. The latest time I tried with the stock rom it simply said "cannot upgrade your phone."
but yes, phone and sms work.
iamkaybo said:
sorry, I have Sprint (shouldve mentioned that)
I get error #777 from data
and I got errors 206, 320, and another 200level one my boyfriend got when he tried. The latest time I tried with the stock rom it simply said "cannot upgrade your phone."
but yes, phone and sms work.
Click to expand...
Click to collapse
Try cycling the battery and re-provisioning your phone first. If that doesn't work change your connection settings. I am not sure on sprint 3g login, but go here:
Start > settings > Connections > Connections
Then click Manage existing for the sprint data connection, click edit. Make sure the "Modem" is "Cellular line" and it is dialing "#777". The last screen should have your sprint 3g data info, if you cannot find it online, call sprint and they can give you that information.
About the ROMs, i'm not sure why it isn't working. Unless you are transposing those numbers wrong there is no info in the wiki at this time:
http://wiki.xda-developers.com/index.php?pagename=Elf_RUU_Error_Codes
I've tried that, my tech friend tried it. Nothing has worked.
iamkaybo said:
I've tried that, my tech friend tried it. Nothing has worked.
Click to expand...
Click to collapse
Did you call sprint yet? That might be the next plan of action, anytime none of those worked I called VZW and got it fixed.
If none of the above works you might have to flash you TP2 via the SD card. Extract the .nbh file and place it on the root of your SD card (do not put it in any folders). Take out your battery, put it back in, hold the volume down and power key. It should automatically load the ROM file and ask if you want to flash the ROM. Hit the power button and flash away.
I called sprint and none of the 3 different tech support agents could figure it out either.
I'll try the SD card thing, because that is looking like my last hope =\
iamkaybo said:
I called sprint and none of the 3 different tech support agents could figure it out either.
I'll try the SD card thing, because that is looking like my last hope =\
Click to expand...
Click to collapse
I had that once with VZW, flashing back to a stock ROM and provisioning is what solved it...hopefully that works for you. Do you need tips on flashing from the SD card or extracting the nbh?
have you tried task29 first, and then reflashing?
kal87 said:
have you tried task29 first, and then reflashing?
Click to expand...
Click to collapse
I agree. It sounds like some left over files are causing a serious conflict. Task 29 will format the phone and give you a clean slate to put the phone into bootloader mode and install a new rom. I have attached a version of Task 29 that I found on PPCGeeks that formats the entire phone and just puts the original "Touch Pro 2" splash screen. Plug in your phone and make sure you have a full sync connection with your phone. After that extract the zip file I attached to your desktop. Then run the Task29.exe file. Go through the whole process as if you were flashing a rom. After that the phone will only go to the splash screen and not boot. Do not panic, this is normal. You now have to put the phone in bootloader mode by holding the volume down button and hitting the soft reset button. Continue to hold down the volume down button when you release the soft reset and dont let it go until you see the bootloader screen. Make sure the phone is still plugged in and the words "USB" pop up on the bottom before you continue. When it does, flash the rom of your choice whether stock or custom and try to see if your problem continues. Sorry for the long instructions but I like being thorough just in case. I always use this before I flash a new rom just to avoid problems. I don't know who the author of this software is but they deserve a lot of credit. Hope this works out for you.
yea, i agree, PRBajista. i use it as well, everytime i flash a new rom (which i plan on doing in a minute or so) before i flash29, i put my new rom's nbh on my sd card, start up active sync, start up boot loader, it'll tell me to presst the power button to flash a new rom, which i don't i hit volume down, so it goes into usb mode, falshes with task 29, after it finishes, i reset holding volume down, and flash my rom from sd cause i prefer it over active sync. i hope everything works out for you
Do you have Hard SPL?
I tried task29 and got the Error [260] as i have the past 3 times i tried just doing the ROM by itself.
I've tried loading the .nbh file onto the SD and doing the whole volume down/power button thing and it just stayed on the bootscreen for 10 minutes not moving.
I am at my wits end and dont know what to do, and now the phone feature (calling/sms) has stopped working as well.