Database Info

I screwed up the unlocking, Please HELP!!!

I didn't read the unlocking SIM procedure by jocky properly. I understood that I MUST get HardSPL installed, and so I go the JumpSPL1.56-KAIS.exe to the phone and then executed it. It got me the tri-color screen (Is this called bootloader?) and then I executed the KaiserCustomRUU.exe from the flash-HardSPL.zip thinking that this will put in the HardSPL into the ROM. The progress bar went upto 95% and then it exited with error and after that the "Recovery" option of the loader hasn't been able to revive the phone. Every time, I put the battery back in and power it up, I get the tri-color screen with the following message:
RUUNBH (on the top right hand side of the screen)
KAIS1*0
SPL-1.56.0000
CPLD-8
I think I now understand the mistake I made. I had a bunch of .nbh files in the directory from where I ran the KaiserCustomRUU after extracting and that is why it must have failed. Now every time I get the tri-color screen when I boot up.
Can someone please help me recover from this position? I have now got the actual simunlocker zip from the original thread and extracted it with folder names and so now I am ready to try again, only if I can recover from the mess I created. Please help!!!

mtty recovered, but I get back the bootloader every time I power up
I used mtty (set 14 0 and boot) to make the phone work (now data was lost and all my prgrams were still there). However, every time I power up my phone, the tri-color screen is back. How can I resolve this?
When I run mtty, I get the following messages on mtty:
set 14 0
HTCST ÚÈÒHTCE
Cmd>boot
InitDisplay: Display_Chip=1
No card inserted
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
FMD_ReadSector+, bad block no=0xFAC0, status:0x0

flash the original rom your device came with! only shot buddy!

Thanks for the advice. Where do I get the original ROM and how do I flash it? After the mess I created, I want to be doubly sure. I remember the versions of ROM that the phone used to show during bootup was R1.27.12.11 and D1.56.00.00 (I don't remember the G number). Appreciate if you could let me know. I have downloaded the Radio ROM numbered 1.27.12.11... is that the original ROM?

if it's a tilt, flashing the original rom will not work, you will get an invalid model error. Instead, use this one RUU_Kaiser_CINGULAR_WWE_1.61.502.2.exe. Trust me, been there done that. (twice)
Once you've done flashing to RUU_Kaiser_CINGULAR_WWE_1.61.502.2.exe and you want to unlock, HardSPL, then flash it back to RUU_Kaiser_CINGULAR_WWE_1.57.502.2, then start w/ step 1 from simunlock.

the_passenger said:
if it's a tilt, flashing the original rom will now work, you will get an invalid model error. Instead, use this one RUU_Kaiser_CINGULAR_WWE_1.61.502.2.exe. Trust me, been there done that. (twice)
Once you've done flashing to RUU_Kaiser_CINGULAR_WWE_1.61.502.2.exe and you want to unlock, HardSPL, then flash it back to RUU_Kaiser_CINGULAR_WWE_1.57.502.2, then start w/ step 1 from simunlock.
Click to expand...
Click to collapse
Did you mean to attach the ROM because it isn't there? I found this thread http://forum.xda-developers.com/showthread.php?t=335568 and it shows a ATT_SPL ROM. But, I ran out of free download limits from rapidshare for today (tonight). Is that the correct procedure? And when you say "flash" the ROM, please correct me if my understanding is wrong:
1. Get the bootloader running (tri-color screen). In my case, just power cycling does it.
2. Have the .nbh file for the ROM and the KaiserCustomRUU.exe in a folder with no other files in it in your PC.
3. Execute the .exe file which should take me thru the prompts on the PC to flash the ROM. I should see a progress bar on the PC as well as cellphone.
Is this procedure correct?
If I am able to get the device back to original state, I will need to find out how I can get the HardSPL loaded "definitively" as well.

sigh, I thought you know how to flash. Anyway, i'm being nice tonight.
http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
get the 1.61.502.2 from that link. put your phone into that tri-color screen, run the exe file you just download. That will bring your Tilt back, if you want to unlock the phone, then read my previous post again, and again and again if you still dont get it.

the_passenger said:
sigh, I thought you know how to flash. Anyway, i'm being nice tonight.
http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
get the 1.61.502.2 from that link. put your phone into that tri-color screen, run the exe file you just download. That will bring your Tilt back, if you want to unlock the phone, then read my previous post again, and again and again if you still dont get it.
Click to expand...
Click to collapse
I know why you feel that way. But, since I screwed up a simple process, my grey cells have really degenerated. My apologies for being dense. I did download that file from the original post of the thread, but now I have run out of free downloads from Rapidshare and I don't have a paypal account. I have to wait another 1hr before it allows me to download. I will try using the Cingular file to flash the device. Fingers crossed!!!

It'll work, dont worry. Just get a new ip and d/l from rapidshare.

Got error 294: Invalid vendor ID, just 1% into flashing. How can I make the phone not go into the boot loader every time I power it ON? Currently, I am using mtty to boot it out of the bootloader.
PS: I had earlier today downloaded the Cingular ROM, but its size as shown in Rapidshare is different from the one you pointed to. I will try that once Rapidshare allows me to.

Looks like the vendor id got screwed up when I had incorrectly flashed the device as I am not able to send emails (POP yahoo mail) or get Direct Push Mail (Outlook) working now. Before this attempt of mine to unlock the SIM, the yahoo and outlook was working fine. Now, during activesync, it says "waiting for network". I am able to browse the internet using PIE though.
I hope the AT&T ROM flashing works.

Downloaded the 1.61 ROM and was able to flash it successfully. It installed all the apps that came with ROM. However, I am not able to access my yahoo POP mail nor my Outlook. I am able to browse the internet though.

Is there a way to get the original AT&T ROM (v1.56) with the 1.27.12.11 radio? I know that that ROM worked fine with my data connections.
Edit: I am able to sync Outlook and Yahoo successfully now with the 1.61 ROM itself.
Thanks to all who helped me with this. I can't thank enough.

Try this first: http://forum.xda-developers.com/showpost.php?p=1894935&postcount=135

i screwed up TytnII
dear all...after flashing my tytnII with DCS V1.3 rom my tytnII is unable to boot up again. the only show on the screen is word "smart mobility" and 3 red lines below it. i have tried everything included hard reset, remove sim card and SD card but still wont help me. i also tried to flashed again but i cannot communicate with activesyn anymore. please if there still way to safe my baby...

Enter to bootloader,and then flash again

thank you for you advice.finally my tyntII is back on line...thanks again my man

jockyw2001 said:
Try this first: http://forum.xda-developers.com/showpost.php?p=1894935&postcount=135
Click to expand...
Click to collapse
Thanks jockyw2001.
Now that my phone is working nicely with the modified AT&T ROM, I want to attempt unlocking the SIM again. I screwed up when I tried to install HardSPL. I will write the procedure here from what I understood from your posts (and thank you very very much for your work). Appreciate if you can confirm that before I show my stupidity again.
Steps:
1. Go to the bootloader by executing JumpSPL1.56-KAIS.exe from the phone
2. Connect thru USB to my Win XP laptop (the loader should show USB)
3. Unzip the contents of flash-HardSPL.zip into an empty folder which will put KaiserCustomRUU.exe and kaiser_hardSPL_1.0.nbh files into the folder.
4. Run the .exe file from that folder which will bring up the ROM loader utility which will automatically load the .nbh file located in the same folder. This will result in the HardSPL being loaded into the phone and the SPL string as seen on the boot loader will change to SPL-1.0 OliPof. Is that a confirmation that HardSPL is loaded?
Can I get out of the boot loader mode after loading HardSPL and continue to use my phone and then attempt the SIM unlocking later?
My phone currently has the AT&T ROm v1.61.502.2 with the Radio ROM v1.27.14.09. Will jocky's unlock method work with this?

Simple Step-By-Step Installation of 3.28 Hard SPL

Credit goes to the creator of the HardSPL files V3.28/3.29; JockyW
Simple Step-By-Step Installation of 3.28 Hard SPL:
I have decided to expand on what has already been posted for those noobeees that are having hard time understanding the HardSPL procedures and are hesitant to flash new cooked ROMs fearing the process was not really explained in details.
You only need two files; SSPL-KAIS.zip and Kaiser-HardSPL-3.28.zip. Save both files on your PC in their own folder for easy access later. Follow these steps to the tee, Do this only if you have your device CID unlocked already ( OliPoff method ):
1. Save then unzip SSPL-KAIS.zip inside a folder on your PC, then copy the unzipped “SSPL-KAIS.exe” onto your device. To do this, connect your device to ActiveSync, After Syncing, Click on Tools from the ActiveSync window, and then click on Explore Pocket PC. “Mobile Device” window appears, Copy SSPL-KAIS.exe by dragging it inside the “Mobile Device” window.
2. Unzip “Kaiser-HardSPL-3.28.zip” in its own folder on your desk top. It will unzip into two files; KaiserCustomRUU.exe and Kaiser-HardSPL-3.28.nbh.
3. Remove your SIM card and your SD card from device. Your device will power off when your SIM card is removed. Power up your device. You are still connected to your PC via USB at this point. Your phone will sync again since it is still connected.
4. On your device, go to “File Explorer” and locate SSPL-KAIS.exe that you copied earlier on your device main memory and click it.
5. Wait for the Bootloader Tri-Color screen to appear and "USB" to show.
6. On your PC bottom tray, Right-click the ActiveSync icon, go into “Connection Settings” and ensure “Allow USB Connections” is unchecked
7. Unplug your device from the USB port, wait 5 seconds, plug it back in.
8. Go to the folder on your PC that has “KaiserCustomRUU.exe” and click it. This will flash the HardSPL on your device.
9. When done flashing, do a soft reset, and you should be good to go.
10. You can use the above steps to flash Kaiser-HardSPL-3.29 if you so desire.
Good luck

Tilt will not receive ROM
I tried flashing the below upgraded Kaiser Rom on my ATT Tilt but now I have the tri-color screen:
KAISI*0
SPL-1.93.000
CPLD-8
The first time it stopped loading at 15%, recovered and now I am getting vendor ID error (294 invalid vendor ID).
I tried others ROMs (including this one) but it just does nothing 0%, errors out, recovery and repeat (update error 262).
After removing battery the tri-color screen says "serial", once I plug in the USB it says USB, but no firmware can be loaded on it.
Does someone have basic firmware that will load when an ATT Tilt gets in this state?
Any help is really appreciated. I just got this thing too. Below was the update I tried that kill my Tilt.
'RUU_Kaiser_HTC_WWE_3.28.405.0_radio_sign_25.83.40.02_1.65.16.25_Ship.exe' that you can find

did u hardspl?

Yes, I had to use the JumpSPL1.56-KAIS (HardSPL fix).

TiltedHTC said:
Yes, I had to use the JumpSPL1.56-KAIS (HardSPL fix).
Click to expand...
Click to collapse
Sounds like your phone is still CID LOCKED. Unlock it using the software posted somewhere else on XDA but NOT in this thread, and try to upgrade the SPL after unlocking.
One way to find out if your device locked or unlocked is that you can try to revert back to the AT&T OEM ROM and flash it. You would then be certain that the CID is locked if your device accepts the OEM ROM.
I wish you posted your troubles in the ROM post where you downloaded the ROM where it belongs; My instructions have nothing to do with your device ROM issues.

I believe you are exactly right! Do you know where there is copy of the AT&T OEM ROM? I would love to have my phone working again.
Sorry for my ignorance. Where is the ROM section for my AT&T Tilt. I got the ROM link from modxxxx .com
Thank you for the assistance.

TiltedHTC said:
I believe you are exactly right! Do you know where there is copy of the AT&T OEM ROM? I would love to have my phone working again.
Sorry for my ignorance. Where is the ROM section for my AT&T Tilt. I got the ROM link from modxxxx .com
Thank you for the assistance.
Click to expand...
Click to collapse
The following link is to Pof's full and clear post on unlocking your device CID. Use it carefully.
http://forum.xda-developers.com/showthread.php?t=334679
Search the forum for RUU_Kaiser_AT_T_CINGULAR_WWE_1.62 Rom, download and then flash. you will be set.

Cingular/AT&T OEM ROM
Download the AT&T OEM ROM from the following link:
http://rapidshare.com/files/55298724...GULAR_WWE_.exe
This is just because I feel good today... Otherwise I would ask you to take the time and do the search yourself. Noobee Spoon-feeding Time...

I found this link to put OEM ROM back:
http://forum.xda-developers.com/showthread.php?t=335568
but the RUU ROM for the AT&T link would not load on my tilt (step 2 of idiots guide). I also did a search for the RUU_Kaiser_AT_T_CINGULAR_WWE_1.62 Rom but no hits.
At least I know what went wrong, now I need to recover the original Rom.
update:
This newbee still won't eat. I got the file (your link is to the same file) but I am getting the same 294 invalid vendor error (after 1%).
I rebooted computer and tried it again with same 294 error.

did you just use jumpspl and used that to load a rom?? why oh why.......

Tilted newbie, did not read enough. Any solutions?

A question.
On your PC bottom tray, Right-click the ActiveSync icon, go into “Connection Settings” and ensure “Allow USB Connections” is unchecked
Do you have to do this ?
I never did that.In my settings USB connections is enabled and it seems to work
/Linus

thaaaanx
i must admit this is the best and clearest step by step guide i have come acrooss thanks a lot mate

just a quick thought..... maybe you should give some credit to jocky

Also,
It wouldn't hurt to mention the "white screen" issues people get when running SSPL.
In such a case they need to use Jump SPL 1.56 or 1.93.
Link Here
Ta
Dave

Thnks man for tutorial. I think it usefull and simple for newbies.

So now, when my Kaiser has Hard-SPL v1 and custom ROM, I can do above steps to upgrade SPL? And then upgrade to custom ROMS without touching SPL?
Thanks

kpcz said:
So now, when my Kaiser has Hard-SPL v1 and custom ROM, I can do above steps to upgrade SPL? And then upgrade to custom ROMS without touching SPL?
Thanks
Click to expand...
Click to collapse
Correct.
Hard SPL's allow you to flash custom ROM's no matter what version.
Ta
Dave

ok, thanks - will give it a try!

It appears there is no way to recover.
Any great excuse that should be used when I take it back for repairs?

Something Went Wrong - HardSPL

First of all, thank you to all the modders out there. Next, thanks to everyone who gave a little time to help me with my problem.
A little background: I have an ATT Tilt, it is about 18 months old and for the most part has been functioning great. I have had several different ROMs on here - I probably have had 12 or so ranging from 6.1 to 6.5 and back. I have been using HardSPL for as long as I can remember. The most current ROM I had was a clean 6.5 Build 23003. It was working really well, except for sometimes I couldn't get the phone to come out of sleep mode and I would have to soft reset. It started happening more and more frequently, so I decided to reflash to Ultimate-X2.V6 -23004. As I was reading through the thread, he recommended HardSPL 3.34 and Radio 1.71.xxx. No problem I said, so I went off to flash 3.34 to replace my 3.56 SPL. I was using a 1.65 radio, but I never got the chance to upgrade.
So thats where the problem starts. When I try to flash the 3.34 SPL (following the instructions and using JumpSPL) it flashes, but then the phone doesn't reboot. I figure the SPL wiped out something, so following the recommendations in the Ultimate X2 thread, I attempt to flash the ATT Stock ROM. I start the phone up in bootloader mode (the bootloader still says 3.56 - interesting eh) and then flash the ATT Stock ROM. The ROM installs but the phone never reboots...
I have tried flashing Radios and other ROMs and redoing the SPL, but the phone just doesn't boot. I can reliably get to the bootloader screen, but it still says 3.56. I tried following the Wiki for "Kaiser Stuck in Bootloader" and flashing ROMs or SPL that way, but it still doesn't work.
I would also love to give you guys that diagnostic information (I should have done this last night) because I was able to view it, but now when I try to boot KAISDIAG.nbh from the memory card it just sits at "Loading...".
I have tried just about every step of different ways of flashing, different SPLs, etc. If there is anything anyone can recommend or try I am more than willing.
Let me know if you need more information or I need to clear anything up.
Again, I appreciate everyone taking time to read this and offer up their expertise.
Thanks,
OutrightLie

Only thing i can suggest is flashing 3.56 again with th SD card. Then 3.34 with the SD card. Or have you tried that already?

Just wondering... do you removed SIM card before flashing your new HardSPL?

I *think* I have tried that.
Does JumpSPL do anything other than put the phone in Bootloader mode? Or is all I have to do, just copy the *.nbh to the memory card, rename it to KAISIMG.nbh and then let it go. If JumpSPL does something more, I may be in trouble because I can't get to an OS.

daigoro64 said:
Just wondering... do you removed SIM card before flashing your new HardSPL?
Click to expand...
Click to collapse
I never have. Not with roms radios or SPL. I know its recomended but i have never had a issue with that.

daigoro64 said:
Just wondering... do you removed SIM card before flashing your new HardSPL?
Click to expand...
Click to collapse
I did remove it the first time, and a few times after that while trying stuff. The first time - for sure. Other times, it was in or out while I was just playing around with stuff. Hopefully something I did subsequently didn't make the problem worse.
Are there any steps I can take to if I did leave the SIM card in during a troubleshooting flash that screwed it up?

OutrightLie said:
I *think* I have tried that.
Does JumpSPL do anything other than put the phone in Bootloader mode? Or is all I have to do, just copy the *.nbh to the memory card, rename it to KAISIMG.nbh and then let it go. If JumpSPL does something more, I may be in trouble because I can't get to an OS.
Click to expand...
Click to collapse
From SD. You will need kaisdiag.nbh and then rename Spl to kaisimg.nbh. Have those both on root of card.

smokestack76 said:
From SD. You will need kaisdiag.nbh and then rename Spl to kaisimg.nbh. Have those both on root of card.
Click to expand...
Click to collapse
I will try that. I need a memory card reader here at work, so this may have to wait until I get home. The only roadblock I see, is right now I have just KAISDIAG on the memory card and it gets stuck at "Loading..." when I attempt to boot. It didn't do this last night, but this morning it seems get stuck there.

OutrightLie said:
I will try that. I need a memory card reader here at work, so this may have to wait until I get home. The only roadblock I see, is right now I have just KAISDIAG on the memory card and it gets stuck at "Loading..." when I attempt to boot. It didn't do this last night, but this morning it seems get stuck there.
Click to expand...
Click to collapse
I have one in my share folder. Might wanna get it and format the card..remember it has to be fat32 and replace the kaisdiag and SPL just to be safe.

I will give it a shot when I get home tonight - unless I can find a memory card reader before then.
Thanks!

Follow exactely this thread
http://forum.xda-developers.com/showthread.php?t=498320
Note your sdcard should be formated FAT32

I just got home. I copied the KAISDIAG.nbh and the 3.56 bootloader (called it KAISIMG.nbh) to the memory card after formatting it to FAT32. It attempts to load the KAISDIAG, but stops at "Loading...". I tried both a 2GB SD Card and an 8GB card, still no luck.
Any other things I can try?

My treo 750 wont boot

Hello people!! i've been reading this forum for a loong time and yesterday i decided to register.I really like this forum but i have a problem.
While tryng to flash my 750 it stops in GSM an it doesn't pass that part and now it only starts in the bootloader screen.
The first two parts, are OK, but then stops in GSM.
Is there any way to make it pass? or to make it boot WM again.
I've tried with diferents WM version (2.23, 2.27 an with WM5) but it's the same.
Can someone help me please?
Thanks in advance!!!
Regards!!!

Did you Hard SPL the phone before trying to flash a ROM?

startngate said:
Did you Hard SPL the phone before trying to flash a ROM?
Click to expand...
Click to collapse
Thanks for your answer.
I've been reading about the Hard SLP but it needs an active sync conection, and I can't do that.
I read it from here.
http://forum.xda-developers.com/showthread.php?t=511763&highlight=hard+slp
Is it the right post?
Thanks a lot!!!

thenyboy said:
Thanks for your answer.
I've been reading about the Hard SLP but it needs an active sync conection, and I can't do that.
I read it from here.
http://forum.xda-developers.com/showthread.php?t=511763&highlight=hard+slp
Is it the right post?
Thanks a lot!!!
Click to expand...
Click to collapse
HardSPL is necessary for you to flash to a non-carrier/custom ROM.
If you have the original ROM with you, you can restore the phone from that ROM package.
Whatever the case, do yourself a favor & find someone with a Windows computer & flash the phone from the desktop ROM package.

Ok, but the thing is that my treo won't boot WM so i can't have a conection with active sync and i can't run de upgrade for desktop.I've already tried that and it doesn't connect.
That's my problem.
it only boots on bootloader screen and shows:
Palm Tr
IPL-0.20
Palm Tr
SPL-0.24.0000
Thats why I can't upgrade using the USB method.
Thanks Again!
Regards!

I'm still in the same situation.
is there any way to Hard SLP with and SD card?
Is it possible without using a desktop computer?
Thanks!!

thenyboy said:
I'm still in the same situation.
is there any way to Hard SLP with and SD card?
Is it possible without using a desktop computer?
Thanks!!
Click to expand...
Click to collapse
From the bootloader screen information, it's obvious you had a stock ROM & had not performed HardSPL.
But since your Treo is able to load the bootloader, all it needs is a stock ROM to be flashed using the SD card method.
Search around here for the SD card updating method & the stock SD update file.
Extract the ROM image onto the SD card according to the instructions & you'll be able to flash the stock ROM onto the Treo.
Once you did that, your Treo should be able to boot WM & you can then perform all the other steps needed to flash a cooked/unofficial ROM onto it.

Help please!
..........

Radio 1.58?

Hello, i've got problem with my GPS so i would like to reflash radio. The file i found in "athena upgrading" section doesn't work. It says to me wrong version. Is there a spécific file for X7510?
Thank you very much.

x7510 Radio Download here

Thank you very much Vico!
When i flash radio does it hard reset my system? I mean erase my file?
In your wonderfull rom is radio included?
Thank you.

wernervw said:
When i flash radio does it hard reset my system? I mean erase my file?
Click to expand...
Click to collapse
I really doubt that it does a hard rest. Since its only radio flash, but I haven't tried.
wernervw said:
In your wonderfull rom is radio included?
Click to expand...
Click to collapse
Thnxs for the complement , no its not included in my rom's. The reason is, that theres no points in reflashing radio rom, unless you have a problem, since the OS update does not affect radio.

Need X7510 radio 1.58
Hi Vico, Happy new year, I have problems with my X7510 radio, actually I don´t know how happened but the radio dissappeared and I want to reflash it, I found the link You had with the radio rom but it said that the file is no longer available, Could you give me another link with the radio room?.
Thank you in advance.

CARDOLFO said:
Hi Vico, Happy new year, I have problems with my X7510 radio, actually I don´t know how happened but the radio dissappeared and I want to reflash it, I found the link You had with the radio rom but it said that the file is no longer available, Could you give me another link with the radio room?.
Thank you in advance.
Click to expand...
Click to collapse
Here, Athena radio 1.58 for you

x7510 Radio

Thank you very much, Hakim but I had an id error when I tried to flash the radio you posted me.
Vico thank you too for the quick reply but I had an 262 error when I tried to flash the radio you posted, I had the Hspl 365, do you think that I have to change to the stock one?
Thank you Vico and Hakim
Greetings from Mexico¡¡¡

Do not change spl to stock. Make sure that your device is x7510 NOT x7500 ect.
Make sure you don't have a sd card, and make sure you are in bootloader mode (camera + reset).

Hi Vico, the model is X7510 and I took out the sd card and tried to flash the radio again, It started well but at the 7% it stopped and now appeared a model ID error [244].
Thank you for your help.

Download my one again, and put your device in bootloader mode, make sure you you only have the two files in a folder. i really don't know what else to do, try another computer maybe?, there is also a way of flash a rom by putting it storage. just try Google

hi vico i just flahs your rom WM6.5.3-23153_128DPI_x7510_6.2_VICO, but have not signal on my divice X7510 , i found this tread and relise that ur roms donst have the radio, iam trying to install this radio Athena 1.58 but have a error massage , . i also try to install the X7510 radio without succes, see the pic atach.
thanx for ur help-

Redownad this new radio (might help) if that dosn't work, i have incledud the original 6.1 htc rom. Just make sure you have Hard-spl "3.05-OliNex", make sure you are in bootloader when you flash.
NEW radio x7510 1.58
Original RUU_Athena_HTC_WWE_3.27.405.3_1.58.00.00_Ship
Also make sure you use 7-zip for extracting, just so there are no errors.

thanks for ur answer ,yes i have the bootloader when i flashing and i have Hard-spl "3.05-OliNex" y tryed to install the new radio but dosent let me , it just send me an error update, i will try to install de stock rom 6.1
i wiil let you know what happens, thanks mate.

vrgolin said:
thanks for ur answer ,yes i have the bootloader when i flashing and i have Hard-spl "3.05-OliNex" y tryed to install the new radio but dosent let me , it just send me an error update, i will try to install de stock rom 6.1
i wiil let you know what happens, thanks mate.
Click to expand...
Click to collapse
i give up, i think i have try almost evrething but no succes flashing te new radio, i dont know what the problem was, and the Original RUU_Athena_HTC_WWE_3.27.405.3_1.58.00.00_Ship also didnt let me flash it, always got just 10 % of the instalation and it stuck, after that i got the update error all the time,
thanks for ur help vico, i areciate.

try flashing rom from on board flash.

Vico100 said:
try flashing rom from on board flash.
Click to expand...
Click to collapse
what do you mean with flashing the rom from on board flash? .
what i did. i rename the RUU_signed.nbh to ATHEIMG.nbh i copy to the mini SD an then try to flash the rom in that way from the mini SD, i put the divice in boot loader and right now the screen said .... Loading.... but thats it,. i still dont see any progres.

According to the manual:
III.Select file system and format the MiniSD card to FAT32 mode.
IV.Copy image file XXX.nbh to the micro SD card and rename to ATHEIMG.NBH.
V.Turn the device power off and insert MiniSD card.
VI.Press and hold Power + Camera button, and Reset button to entry Boot loader mode.
VII.Press Power button to start upgrade procedure.
VIII.Reading source code from MiniSD card.
[Note]: This process will takes 15 mins, please don’t power off the device.
IX.After finish, press Reset button to reboot.
So probably make sure its the only file on the sd (and do it exact capital letters ect)

Vico100 said:
According to the manual:
III.Select file system and format the MiniSD card to FAT32 mode.
IV.Copy image file XXX.nbh to the micro SD card and rename to ATHEIMG.NBH.
V.Turn the device power off and insert MiniSD card.
VI.Press and hold Power + Camera button, and Reset button to entry Boot loader mode.
VII.Press Power button to start upgrade procedure.
VIII.Reading source code from MiniSD card.
[Note]: This process will takes 15 mins, please don’t power off the device.
IX.After finish, press Reset button to reboot.
So probably make sure its the only file on the sd (and do it exact capital letters ect)
Click to expand...
Click to collapse
well let me tell u tahat i have 2 divices X7510 the first one:
ROM ver. 3.29.xTep_3_00 wwe
ROM date 01/25/09
Radio ver. n/a ... the divice dosent have radio/ dosent let me install after 7%
IPL-v2. 02
ATHE400
spl-3.05.0000
on this divice dosent let me instal a radio , after 7 % it fail, and when i want to to flash the stock rom from my computer , after 10 % it fail, and i flashed from the SD following the steps u metion here , but nothing hapens after the 3 color bootscreen .
the second divice X7510 :
ROM: WM6.5.3-23153_128DPI_x7510_6.2_VICO
Radio ver. n/a ... the divice dosent have radio/ dosent let me install after 7%
IPL-v2.02
ATHE400
SPL-v3.65. OilNex
i have the same problem on both divice

Hi Vico, thank you again for your support, I downloaded the second file that you upload "X7510 1.58 radio" and I uncompressed it with 7 zip and now I could flash the radio with out problems.
Thanks again for your help and patience¡¡¡
If you need something from Mexico just say it...