White screen question - Tilt, TyTN II, MDA Vario III Windows Mobile ROM De

Ok so I loaded SPL via the sticky above for a white screen. I am stuck on the tri color screen. When I try to run PDA Phone ROM update utility it runs to 20% then fails. Restart and try again and it will not move past 0%.
I know this has been covered multiple times, can you direct me in the correct direction

A stickied post no less ...
http://forum.xda-developers.com/showthread.php?t=354061

i know. I looked at this screen. I got the damn:
RUUNBH
KAIS1*0
SPL-1.56.0000
CPLD-8
Screen
Cannot flash via sd card. Awaiting factory rom to finish downloading to try thing.
ANything else I can try?

Related

Need spl-1.93.0000 please help stuck from sim unlock.

Got stuck trying to sim unlock in step 1 of the files (flashing the special radio) error at 95% and now I can't get out of the tri color screen. I tried to reflash the radio but with no luck. I also tried to flash the original AT&T tilt stuff with no luck as well, invalid ID code?. Through searching I found I need to get the correct SPL to get past the tri-color.
Below is what my screen displays.
RUUNBH
KAIS1*0
SPL-1.93.0000
CPLD-8
USB when pluged and serial when not.
It can get into the % screen when trying to flash but immediately dies after 1% if I don't get an error first. Any help will be greatly appreciated along with a little paypal gratitude. Thanks in advance- Bryan
Bryan858 said:
Got stuck trying to sim unlock in step 1 of the files (flashing the special radio) error at 95% and now I can't get out of the tri color screen. I tried to reflash the radio but with no luck. I also tried to flash the original AT&T tilt stuff with no luck as well, invalid ID code?. Through searching I found I need to get the correct SPL to get past the tri-color.
Below is what my screen displays.
RUUNBH
KAIS1*0
SPL-1.93.0000
CPLD-8
USB when pluged and serial when not.
It can get into the % screen when trying to flash but immediately dies after 1% if I don't get an error first. Any help will be greatly appreciated along with a little paypal gratitude. Thanks in advance- Bryan
Click to expand...
Click to collapse
And did you flash HardSPL before? It's in sticky threads on the top of the XDA page
gabriel31337 said:
And did you flash HardSPL before? It's in sticky threads on the top of the XDA page
Click to expand...
Click to collapse
That is the very first thing stated in the instructions for the simunlock. Bryan858, have you tried reflashing the original radio, not the patched one back to your phone? Also, try the HardSPL now and see if you can get that going on your phone.
This post may help you.
First try to clear RUUNBH mode and see if it boots thru.
If not you must make a note of CID and ModelID and find a matching ROM
Thanks for the replies.
I have tried hardspl again but since activesync does not come up it does not work and also already tried the original radio. I even tried the original radio with rom.
Tried running mtty with "task 8" phone just blinks once then back to the same ruunbh screen then the mtty cmd screen seems frozen. below is what comes from info 0 and info 2
Cmd>info 0
Platform Model ID:KAIS1*000
Platform HW Board ID:31, PVT1
Cmd>info 2
HTCSCWS__001Ùü¤HHTCE
How do I go about getting the right stuff to load from the above? Or can I edit the ones I'm going to flash to reflect the above just to get the phone to windows again?
Bryan858 said:
Cmd>info 0
Platform Model ID:KAIS1*000
Platform HW Board ID:31, PVT1
Cmd>info 2
HTCSCWS__001Ùü¤HHTCE
How do I go about getting the right stuff to load from the above? Or can I edit the ones I'm going to flash to reflect the above just to get the phone to windows again?
Click to expand...
Click to collapse
Your CID=CWS__001 and ModelID=KAIS1*000
Search for a matching official RUU.
Thanks but,
Does that just mean any HTC WWE 1*000 rom? I just tried one and get the same result. It cuts out at 1%.
Got it going.
Ok heres what I did in case anyone comes across the same problems I hope this will help you out.
After a full night of trying to flash almost all the roms and radios I downloaded I gave up and left the battery out so it wouldn't drain. This afternoon I tried again with no luck and repeatidly tried using MTTY CMD> task 8 to get out of the ruu screen with no luck just repeated blinking back to the same screen. I then resarted my whole computer and tried the mtty again once same results then tried the original shipped radio with rom error at 1% then I tried flashing to the updated rom I had installed before the problems occured and it was finally able to get back to windows. I don't know why it worked this time because I had tried it several times last night with no luck. I guess being persistant pays off.
Jock, thanks for trying to help me out and for your great software releases. I'll try to send a couple bucks or whatever the remaining balance is in my paypal account. Thanks again....

Newbie just bricked phone HELP!!

Ok I'm freaking out hear fellas! Tried installing Hard SPL and it gave me the white screen so I went ahead and used the files from the "White screen solved thread". I got the tri-color screen and unplugged the USB connector and reconnected it. Then i downloaded the new q-mobile rom and went through the onscreen prompts. It went up to 20% and froze. I followed the online instructions to try and recover and not the update freezes at 0%. Now I am stuck at the tri-color screen and it says.
KAIS1*0
SPL-1.56.0000
CPLD-8
Please tell me I didn't just throw $600 dollars out the window. I would be greatful for any help you guys can give.
According to what your wrote above, it does not look like you actually installed Hard-SPL. When you finished installing Hard-SPL your tri-color screen should have read SPL-1.0.OliPof, is that what you saw?
Either way check this thread it might help you.
Link
Good Luck.
j.a said:
According to what your wrote above, it does not look like you actually installed Hard-SPL. When you finished installing Hard-SPL your tri-color screen should have read SPL-1.0.OliPof, is that what you saw?
Either way check this thread it might help you.
Link
Good Luck.
Click to expand...
Click to collapse
Also you may try this thread.. had similar problem with a friends
http://forum.xda-developers.com/showthread.php?t=354061
Hope one of these helps

Tilt Stuck at 3 color screen...Help!

installed hardspl, began flashing, got to 20% then error 262. now get error 262 at 0%.
What can I do?
Screen has RUUNBH in the top right corner.
KAIS1*0
SPL-1.56.0000
CPLD-8
fitdocsr said:
installed hardspl, began flashing, got to 20% then error 262. now get error 262 at 0%.
What can I do?
Screen has RUUNBH in the top right corner.
KAIS1*0
SPL-1.56.0000
CPLD-8
Click to expand...
Click to collapse
While in the tri color screen.
Flash to this ROM.
http://rapidshare.com/files/5340369...adio_sign_22.45.88.07_1.27.11.31_Internal.exe
Yeah, I had a similar problem. The only ROM that worked for me was the newest AT&T ROM (1.61.502.2) that was posted in the Kaiser ROM wiki. All the other ROM's failed (even the same build that was on my device). This was after I was trying to put on the HardSPL to get it unlocked.
I had the White Screen of Death and was testing some new builds of the SPL stuff and got into the 3 color state of doom.
I'm pretty sure this is the ROM I used:
http://forum.xda-developers.com/showthread.php?t=357123
TTFN
Thanks for the replies.
Here is what i ended up doing.
open mtty, press enter, then type boot, enter
got the phone to boot back to windows mobile then ran customruu from there.
I thought I had bricked it, certainly scared me.
I had this problem yesterday. I went through the "recovery" process. This brought me back to the 3 Color screen. From there I clicked the HardSPL exe. Pressed enter, let HardSPL run for a few seconds(the screen didn't change but I could hear the laptop working). Then opened the RUU for any ROM I wanted to install.
This avoided installing an intermediate factory ROM.
This only works one time each time I recovered. If I canceled out of the RUU I had to go through the recovery process again.
1. Unplug USB
2. Remove Battery
3. Wait 3 seconds
4. Install battery
5. Turn on phone
6. Plug in USB
Good Luck!

Did I Brick my Kaiser ?

Hello all
I followed all the instructions as per the post " HardSPL will not install - WHITE SCREEN: SOLVED (UPDATE 01. March 2008)"
I upgraded the rom to Mobile Vista 1.1 and it worked fine. I then wanted to check out Laurentan's , Sleuth's and Dutty's Roms.
I Loaded the JumpSPL1.56-KAIS.exe on the Phone and proceeded to load L26_WM_6.1_PRO.V6. At 17 Percent I received an Error and went through the recovery process but afterwards it would would display tree color screen and as soon as i update it changes the screen to the white one with the p;rogress bar at the top. It however stays on 0 percent. I then tried to update via the Micro SD Card and it briefly displays the Tri color screen and then a white screen with Loading.... . It then remains there indefinitely
On the tri Color screen i have the following
Top Right RUUNBH
Left KAIS130
Left SPL-1.93.0000
Left CPLD-8
Mosquito007 said:
Hello all
I followed all the instructions as per the post " HardSPL will not install - WHITE SCREEN: SOLVED (UPDATE 01. March 2008)"
I upgraded the rom to Mobile Vista 1.1 and it worked fine. I then wanted to check out Laurentan's , Sleuth's and Dutty's Roms.
I Loaded the JumpSPL1.56-KAIS.exe on the Phone and proceeded to load L26_WM_6.1_PRO.V6. At 17 Percent I received an Error and went through the recovery process but afterwards it would would display tree color screen and as soon as i update it changes the screen to the white one with the p;rogress bar at the top. It however stays on 0 percent. I then tried to update via the Micro SD Card and it briefly displays the Tri color screen and then a white screen with Loading.... . It then remains there indefinitely
On the tri Color screen i have the following
Top Right RUUNBH
Left KAIS130
Left SPL-1.93.0000
Left CPLD-8
Click to expand...
Click to collapse
My suggestion would be to flash back to the original shipped ROM. Doesn't look like you have a HardSPL done. Anybody else have any input?
Thx All The Way
Can i load the original by renaming it to KAISIMG.nbh and running it from my SD card?
Is this the correct rom to load?
http://rapidshare.com/files/5781641....5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar (64063 KB).
I just need to make sure I download the correct one as i have a really crappy internet connection and a download 60 Mb download wastes 5 hours
Thanks again
Mosquito
Mosquito007 said:
Thx All The Way
Can i load the original by renaming it to KAISIMG.nbh and running it from my SD card?
Is this the correct rom to load?
http://rapidshare.com/files/5781641....5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar (64063 KB).
I just need to make sure I download the correct one as i have a really crappy internet connection and a download 60 Mb download wastes 5 hours
Thanks again
Mosquito
Click to expand...
Click to collapse
I would say that's correct but do you remember what ROM version / radio who had when you received the phone.
No unfortunately I don't. I had fingers in first and brains in neutral when the downloads finished
Mosquito007 said:
No unfortunately I don't. I had fingers in first and brains in neutral when the downloads finished
Click to expand...
Click to collapse
Try flashing to the ROM you posted via your SD Card.
Thank for the help. The Kaiser Lives again. I understand that if i dont Hard SPL I have to Load an Image and before I can load the next cooked Image I have to revert back to the original and then only load the next Cooked one.
Cheers
Newbie - On a learning curve
Click this thread, it worked for me!
http://forum.ppcgeeks.com/showthread.php?t=17623
Not sure if I'm allowed to link to another website but if it helps a fellow Kaiser user!
You need to download MTTY, then follow the instructions, if it works your Kaiser will reboot to the original ROM.
Good luck!
I wouldn't reccomend newbie to play with MTTY. It's a very dangerous toy to play with.
Read the follwoing thread" http://forum.xda-developers.com/showthread.php?t=372497&highlight=mtty
BE CAREFUL!
Amir.

Bricked my phone. Help please

Hey guys. Well i am massively stuck.
I have tried to unlock my Kaiser like I have done before using the tools provided here.
I ran jumpspl on the phone and then tried to unlock the radio. Thus where I have been stuck.
I have not been able to get the procedure past the 0% mark and I seemed to have tried everything to get it out of the SPL.
My screen is white with the RGB colours on saying
top left:
KAIS130
SPL-3.27.0000
CPLD-8
Top right:
RUUNBH
I cant get the fone to boot and it is stuck. I cant get the MTTY thing to connect to my fone and at a lose end. Any help would be amazing...
Thanks
Mike
mikeseaman3000 said:
Hey guys. Well i am massively stuck.
I have tried to unlock my Kaiser like I have done before using the tools provided here.
I ran jumpspl on the phone and then tried to unlock the radio. Thus where I have been stuck.
I have not been able to get the procedure past the 0% mark and I seemed to have tried everything to get it out of the SPL.
My screen is white with the RGB colours on saying
top left:
KAIS130
SPL-3.27.0000
CPLD-8
Top right:
RUUNBH
I cant get the fone to boot and it is stuck. I cant get the MTTY thing to connect to my fone and at a lose end. Any help would be amazing...
Thanks
Mike
Click to expand...
Click to collapse
have you tried flashing a hard-spl?
mikeseaman3000 said:
Hey guys. Well i am massively stuck.
I have tried to unlock my Kaiser like I have done before using the tools provided here.
I ran jumpspl on the phone and then tried to unlock the radio. Thus where I have been stuck.
I have not been able to get the procedure past the 0% mark and I seemed to have tried everything to get it out of the SPL.
My screen is white with the RGB colours on saying
top left:
KAIS130
SPL-3.27.0000
CPLD-8
Top right:
RUUNBH
I cant get the fone to boot and it is stuck. I cant get the MTTY thing to connect to my fone and at a lose end. Any help would be amazing...
Thanks
Mike
Click to expand...
Click to collapse
What happens when you remove the battery and try to re-start the phone? Have you tried to soft re-set?
SPL2.27 is a good sign. Your device needs CID unlocking as it is a preferred process prior to updating the SPL as well as flashing a new cooked ROM. Read some of the stickies and understand the procedure and you will be fine.
A quick note: the HTC Kaiser is an indestructible device. It endures all kinds of software abuse, and will survive the severest Nubie flashing indulgence. So do not worry! you can get it back to normal.
Do the following first:
I would recommend if you see the four colors on the screen and USB at the bottom of the screen, to flash an OEM HTC or AT&T ROM Dated August 2008. This will clear all bad temp files and will render the device to default stage.
XDA-Wiki is your best friend. After that you can CID unlock the device then start flashing cooked ROMs.
Thread closed.
See my hints in my thread where you also posted.
Dave

Categories

Resources