Newbie just bricked phone HELP!! - Tilt, TyTN II, MDA Vario III Windows Mobile ROM De

Ok I'm freaking out hear fellas! Tried installing Hard SPL and it gave me the white screen so I went ahead and used the files from the "White screen solved thread". I got the tri-color screen and unplugged the USB connector and reconnected it. Then i downloaded the new q-mobile rom and went through the onscreen prompts. It went up to 20% and froze. I followed the online instructions to try and recover and not the update freezes at 0%. Now I am stuck at the tri-color screen and it says.
KAIS1*0
SPL-1.56.0000
CPLD-8
Please tell me I didn't just throw $600 dollars out the window. I would be greatful for any help you guys can give.

According to what your wrote above, it does not look like you actually installed Hard-SPL. When you finished installing Hard-SPL your tri-color screen should have read SPL-1.0.OliPof, is that what you saw?
Either way check this thread it might help you.
Link
Good Luck.

j.a said:
According to what your wrote above, it does not look like you actually installed Hard-SPL. When you finished installing Hard-SPL your tri-color screen should have read SPL-1.0.OliPof, is that what you saw?
Either way check this thread it might help you.
Link
Good Luck.
Click to expand...
Click to collapse
Also you may try this thread.. had similar problem with a friends
http://forum.xda-developers.com/showthread.php?t=354061
Hope one of these helps

Related

Need spl-1.93.0000 please help stuck from sim unlock.

Got stuck trying to sim unlock in step 1 of the files (flashing the special radio) error at 95% and now I can't get out of the tri color screen. I tried to reflash the radio but with no luck. I also tried to flash the original AT&T tilt stuff with no luck as well, invalid ID code?. Through searching I found I need to get the correct SPL to get past the tri-color.
Below is what my screen displays.
RUUNBH
KAIS1*0
SPL-1.93.0000
CPLD-8
USB when pluged and serial when not.
It can get into the % screen when trying to flash but immediately dies after 1% if I don't get an error first. Any help will be greatly appreciated along with a little paypal gratitude. Thanks in advance- Bryan
Bryan858 said:
Got stuck trying to sim unlock in step 1 of the files (flashing the special radio) error at 95% and now I can't get out of the tri color screen. I tried to reflash the radio but with no luck. I also tried to flash the original AT&T tilt stuff with no luck as well, invalid ID code?. Through searching I found I need to get the correct SPL to get past the tri-color.
Below is what my screen displays.
RUUNBH
KAIS1*0
SPL-1.93.0000
CPLD-8
USB when pluged and serial when not.
It can get into the % screen when trying to flash but immediately dies after 1% if I don't get an error first. Any help will be greatly appreciated along with a little paypal gratitude. Thanks in advance- Bryan
Click to expand...
Click to collapse
And did you flash HardSPL before? It's in sticky threads on the top of the XDA page
gabriel31337 said:
And did you flash HardSPL before? It's in sticky threads on the top of the XDA page
Click to expand...
Click to collapse
That is the very first thing stated in the instructions for the simunlock. Bryan858, have you tried reflashing the original radio, not the patched one back to your phone? Also, try the HardSPL now and see if you can get that going on your phone.
This post may help you.
First try to clear RUUNBH mode and see if it boots thru.
If not you must make a note of CID and ModelID and find a matching ROM
Thanks for the replies.
I have tried hardspl again but since activesync does not come up it does not work and also already tried the original radio. I even tried the original radio with rom.
Tried running mtty with "task 8" phone just blinks once then back to the same ruunbh screen then the mtty cmd screen seems frozen. below is what comes from info 0 and info 2
Cmd>info 0
Platform Model ID:KAIS1*000
Platform HW Board ID:31, PVT1
Cmd>info 2
HTCSCWS__001Ùü¤HHTCE
How do I go about getting the right stuff to load from the above? Or can I edit the ones I'm going to flash to reflect the above just to get the phone to windows again?
Bryan858 said:
Cmd>info 0
Platform Model ID:KAIS1*000
Platform HW Board ID:31, PVT1
Cmd>info 2
HTCSCWS__001Ùü¤HHTCE
How do I go about getting the right stuff to load from the above? Or can I edit the ones I'm going to flash to reflect the above just to get the phone to windows again?
Click to expand...
Click to collapse
Your CID=CWS__001 and ModelID=KAIS1*000
Search for a matching official RUU.
Thanks but,
Does that just mean any HTC WWE 1*000 rom? I just tried one and get the same result. It cuts out at 1%.
Got it going.
Ok heres what I did in case anyone comes across the same problems I hope this will help you out.
After a full night of trying to flash almost all the roms and radios I downloaded I gave up and left the battery out so it wouldn't drain. This afternoon I tried again with no luck and repeatidly tried using MTTY CMD> task 8 to get out of the ruu screen with no luck just repeated blinking back to the same screen. I then resarted my whole computer and tried the mtty again once same results then tried the original shipped radio with rom error at 1% then I tried flashing to the updated rom I had installed before the problems occured and it was finally able to get back to windows. I don't know why it worked this time because I had tried it several times last night with no luck. I guess being persistant pays off.
Jock, thanks for trying to help me out and for your great software releases. I'll try to send a couple bucks or whatever the remaining balance is in my paypal account. Thanks again....

What is wrong with my phone? Tried to Flash new Rom...Black Screen

Okay. I tried to install one of Dutty's ROM's that can be found here: http://forum.xda-developers.com/showthread.php?t=398271.
I read through all the stickys and FAQ's first. I read Dutty's wiki, the Kaiser wiki, and the flashing new ROM wiki. I followed all of the directions and followed Dutty's instructions to the T.
After installing the HardSPL found here(http://forum.xda-developers.com/showthread.php?t=334679), I backed up all my personal info/data.
Then used the Custom RUU Dutty supplied and proceed through the ROM flashing process. Everything went fine and I got no error messages. But when my phone booted up I got a black screen. I waited but my phone stayed on the black screen. So I pressed the standby button on and off a few times and eventually I wound up with a black screen that had about a million multi-colored speckled dots all over it. And I have been stuck on this screen since. I've tried soft-reseting and hard resetting but nothing is working.
I am Using an ATT Tilt BTW.
Please Help me. My phone is my life so right now I'm feeling like Dionne Farris.....Hopeless....
ahh that sounds like a nightmare... wish i could help
klrob33 said:
Okay. I tried to install one of Dutty's ROM's that can be found here: http://forum.xda-developers.com/showthread.php?t=398271.
I read through all the stickys and FAQ's first. I read Dutty's wiki, the Kaiser wiki, and the flashing new ROM wiki. I followed all of the directions and followed Dutty's instructions to the T.
After installing the HardSPL found here(http://forum.xda-developers.com/showthread.php?t=334679), I backed up all my personal info/data.
Then used the Custom RUU Dutty supplied and proceed through the ROM flashing process. Everything went fine and I got no error messages. But when my phone booted up I got a black screen. I waited but my phone stayed on the black screen. So I pressed the standby button on and off a few times and eventually I wound up with a black screen that had about a million multi-colored speckled dots all over it. And I have been stuck on this screen since. I've tried soft-reseting and hard resetting but nothing is working.
I am Using an ATT Tilt BTW.
Please Help me. My phone is my life so right now I'm feeling like Dionne Farris.....Hopeless....
Click to expand...
Click to collapse
can you get into bootloader mode?
hold down power and camera button while inserting stylus it should introduce you to the tri color screen. Please tell us what it states. You may have just experienced a bad flash or you have the radio from hell installed on your device
redbandana said:
can you get into bootloader mode?
hold down power and camera button while inserting stylus it should introduce you to the tri color screen. Please tell us what it states. You may have just experienced a bad flash or you have the radio from hell installed on your device
Click to expand...
Click to collapse
Yes I can get to Bootloader mode.
In the red bar it says:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
And Serial at the bottom in the white bar where USB normaly would be.
klrob33 said:
Yes I can get to Bootloader mode.
In the red bar it says:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
And Serial at the bottom in the white bar where USB normaly would be.
Click to expand...
Click to collapse
ok soft reset your phone and when it starts up does something like this appear in red text?
r 1.65.20.29
g 25.88.40.04w
d 3.29.xx.xx
please tell me what it says after R
R- 1.58.25.17
klrob33 said:
R- 1.58.25.17
Click to expand...
Click to collapse
well it appears to be a bad flash. unplug your device from the usb cable, restart your computer, and flash again.
Hopefully after your computer restarts it will recognize the device as being connected. If it doesn't just double click on your windows mobile device center icon and it should connect. After connecting just reflash the rom
edit
I had the same problem, what i did was read all through the thread of the ROM or while inside the thread i use the search function and type in the keywords like "blank screen" it happened to me exactly, but i didnt bother to post since i found the answer, 1 user said flash it to WM 6.1 i did exactly that and it helped! some said not necessary, but i didnt see that instruction so i flashed the 6.1 blindly and fortunately it worked...
here is the thread
http://forum.xda-developers.com/showthread.php?t=375583&page=30
on the search function type black screen and you should get and idea what you need to do...
redbandana said:
well it appears to be a bad flash. unplug your device from the usb cable, restart your computer, and flash again.
Hopefully after your computer restarts it will recognize the device as being connected. If it doesn't just double click on your windows mobile device center icon and it should connect. After connecting just reflash the rom
edit
Click to expand...
Click to collapse
I tried that and It different work. I'm trying a whole new ROM now and I hope it works.
Problem solved.
Thanks to everybody for their help.
I just used a different ROM and everything worked perfectly. I guess that ROM just didn't want to work with my phone. But it's okay. The ROM I'm using now is perfect.

Flashed ROM not loading

If the answer is one this site already I apologize to everyone but I have been searching for 3 days now and no joy.
I will try to keep is short and simple.
I have been flashing for the last year now and have never had trouble until now. Flashed Duttys ROM released on June 5th I believe. Went great but still had old HardSPL on my phone. Followed the steps to flash latest SPL 3.29 and it never took. As a matter of fact something happened to the USB and my pc was unable to recognize the device. So I was stuck for the moment and had to leave that way until I had more time.
Received a phone call and when I hung up it went to white screen with call graphics at the bottom, missed call, received call, etc. I soft reset the phone and then the Tri-Color screen came up and this is the info:
KAIS130 MFG
SPL-1.0.0lIPof
CPLD
I am assuming this is the first HardSPL that I loaded. So then I preceed to flash via SD and it says that the flash completed and was successful. However when I soft reset the phone goes back to the Tri-Color sceen and does not load the image I just flashed.
Anyone have any ideas how I can get this phone working again? I am open to any and all suggestions.
Thank you in advance
does the bootloader show ruunbh on top?
ok this should be an easy fix! the poster above asked the right question!
lets start from scratch now though ok,
-first download SSPL.KAIS and save it to your memory card.
- Download Which ever hardSPL you would like to use.
- run SSPL.KAIS from SD card and then flash New HardSPL, check to make sure it flashed right by going into bootloader should say what ever SPL you just flashed.
- If that flashed correctly then proceed to flashing the HTC WM6.1 shipped ROM, which can be found on the forum! Make sure its a NON-cooked rom...
- If that flashed correctly then pick which ever custom rom you would like and flash that, make sure that flashed correctly and if so your done
Austinsnyc,
Thanks for the speedy reply. Sorry just a few questions and one statement.
The phone is in the Tri-Color screen state constantly. The only way I can load the bootloader is if I rename a ROM to KAISIMG.nbh. Then is something akin to ROM, radio, etc and when that flashes they will have an OK next to them. Alright with that said a few questions.
Do I have to rename the SSPL.KAIS file, it does not run as is? When loaded on the the card, Tri-Color comes up and then for a brief second is says, Loading.....No Image File.
Do I load both files on the card at the same time and do I have to rename them? i.e. KAISIMG.nbh
Thank you for your help
thesire said:
does the bootloader show ruunbh on top?
Click to expand...
Click to collapse
No it doesn't. I will say KAISIMG.nbh, the ROM I renamed to load. Then is list all the features of that ROM, i.e. OS, SPL, radio. I flash it and it says success but still will not load.
Thank you
culleyps said:
No it doesn't. I will say KAISIMG.nbh, the ROM I renamed to load. Then is list all the features of that ROM, i.e. OS, SPL, radio. I flash it and it says success but still will not load.
Thank you
Click to expand...
Click to collapse
MTTY
cmd>set 16 0
cmd>boot
Can MTTY be run form the SD card?
I didn't clarify so well, I cannot use usb connectivity to the PC. Everyting needs to be done off the SD card.
Thank you
culleyps said:
Can MTTY be run form the SD card?
I didn't clarify so well, I cannot use usb connectivity to the PC. Everyting needs to be done off the SD card.
Thank you
Click to expand...
Click to collapse
okay read more about mtty for clarrification. as long as it says usb when u hook up to computer in bootloader u should be fine. but first read on mtty before running cmds.
thesire said:
okay read more about mtty for clarrification. as long as it says usb when u hook up to computer in bootloader u should be fine. but first read on mtty before running cmds.
Click to expand...
Click to collapse
thesire,
I will research the this more. It does say usb on the phone with plug in otherwise when unplugged it says serial. When plugged in I can't see usb in the drop down in MTTY. I will keep reading.
Btw, it now says RUUNBH in the top right hand corner.
Thanks
culleyps said:
thesire,
I will research the this more. It does say usb on the phone with plug in otherwise when unplugged it says serial. When plugged in I can't see usb in the drop down in MTTY. I will keep reading.
Btw, it now says RUUNBH in the top right hand corner.
Thanks
Click to expand...
Click to collapse
that means you have bad data blocks which can also be cleared using mtty.
I must be very thick, I can't get MTTY to connect. Every time I plug in the USB to my Vista OS pc is says it can't recongize the device and it has malfucntioned. I know the USB is working, it was up until I was having this problem at least.
So I start MTTY and look for USB in the drop down for Port but only COM 1 & 2 show up.
So any other suggestions you or anyone else may have is greatly appreciated.
Thanks for your patience
with Vista you need to use Mtty 5.13 which can be found in the FrankenKaiser radio from hell thread. There is also a guide on how to install the old XP drivers to WindowsMobileDeviceCenter that helps a bunch with USB issues. Also I think you miss understood me the tri-color screen is the Bootloader screen!!!
USERNAME said:
that means you have bad data blocks which can also be cleared using mtty.
Click to expand...
Click to collapse
I don't think it means bad blocks for sure.
Ok. I have read just about everything I can find on MTTY, old XP drivers (which I already have installed) and I still can not get anything to work. When I plug in the phone via usb, pc says it cannot recongize the device and it must have malfunctioned. I have tried MTTY 5.13 numerous times and still cannot get usb to show up and have been unseccessful with all my attempts to connect via a COM port.
Is there any place in NYC, Brooklyn or Queens that I can take this phone too and someone with more experience can fix this for a fee of course? I just and need to get my phone working again.
So I have another question since I have been unable to get anywhere with the dang thing.
I am unable to get my laptop/pc to recognize the phone, I can't even get drives to load. Been searching and reading and still looking for a solution to this issue. If you know where is answer is in this forum could you please point me in the right direction?
Aslo, if someone is willing to spend the time with me to solve this issue get the phone running again, I will be more the happy to donate generously.
I think this can be solve quickly if I could get the time with someone.
For the folks that have replied, I can't thank you enough it has been a great learning experience.
Thanks
Same problem here. Please help!
I am having exactly the same problem. PANIC!
I am a complete noob to all this, but managed to flash Duttys Rom.
(Ruu_Signed_Duttys_WM6.1_Official_5.2.19209_1_58_16_27 [FIX])
I was incredibly pleased with the results.
The phone ran better than ever till this morning. The sound stopped working, I soft reset and now I cant get past the tri-coloured (boot loader ?) screen.
KAIS130
SPL-3.29.Hard
CPLD-8
SERIAL
I cant hard reset, it just goes back to the tri-colour screen.
Help!
If I am not being clear or more info is needed please let me know.
5manarmy said:
I am having exactly the same problem. PANIC!
I am a complete noob to all this, but managed to flash Duttys Rom.
(Ruu_Signed_Duttys_WM6.1_Official_5.2.19209_1_58_16_27 [FIX])
I was incredibly pleased with the results.
The phone ran better than ever till this morning. The sound stopped working, I soft reset and now I cant get past the tri-coloured (boot loader ?) screen.
KAIS130
SPL-3.29.Hard
CPLD-8
SERIAL
I cant hard reset, it just goes back to the tri-colour screen.
Help!
If I am not being clear or more info is needed please let me know.
Click to expand...
Click to collapse
Does it say RUUNBH in the top right corner?
Hi.
All I can see on the screen is as follows.
------------------------------------
KAIS130SPL-3.29.Hard
CPLD-8
Serial
------------------------------------
I have absolutely no idea where to go from here.
Cold sweat....
5manarmy said:
Hi.
All I can see on the screen is as follows.
------------------------------------
KAIS130SPL-3.29.Hard
CPLD-8
Serial
------------------------------------
I have absolutely no idea where to go from here.
Cold sweat....
Click to expand...
Click to collapse
The best thing for you to do is contact GSLEON3 to see if he can help you out.
Thanks for your response.
I somehow seem to have gotten somewhere.
I just repeatedly kept trying to hard re-set, taking the battery out, connecting USB.... and then it hard-reset.
They say the definition of insanity is doing the same thing and expecting different results.
I wonder if you can recommend a stable ROM? I love the speed and battery life of the one I installed but dont like the idea of being between meetings and having a phone in limbo.
Thanks again.

Help repair my htc kaiser 130(uk orange)

Tried to changed 2 htc kaiser130(orange uk network) to original htc rom, but both got damaged, one of them got error at 22%, and the other is 16%, I'm stuck in the Bootloader (Tri-Color) Screen with "ruunbh" text in the upper right corner, now the phone is not take any flash, search the solution for that, download the orange rom, but it is not even start flash, but with some of the rom, it can start, only 1%, then got id error. please help me to bring my phone back to life.
okies well this should be an easy fix if you had hard SPL installed? did you have hardSPL? if all else fails try FrankenKaiser
austinsnyc said:
okies well this should be an easy fix if you had hard SPL installed? did you have hardSPL? if all else fails try FrankenKaiser
Click to expand...
Click to collapse
Hello, thanks for your reply, tried frankerkaiser, nothing happen, it is not change the state, as the phone power on, goes to ruunbh error on the right top corner.
Is there any other way to unbrick my phones. Thanks a lot.
Hello
You must have MTTY.
First conect your HTC to the computer, disable Active sincronization, open MTTY to conect with your device from USB, push ENTER and afther that you have:
Cmd>
Write boot and push enter:
Cmd>boot +Enter
Afther that your HTC must restart and can make a soft reset.
try to flash 3.34.721.2 official rom.. this rom fix many problems..
Umm This thread is 8 months old. Please don't dig in the graveyard
JimmyMcGee said:
Umm This thread is 8 months old. Please don't dig in the graveyard
Click to expand...
Click to collapse
Hey, The guy could have been waiting patiently ( 8 months )for an answer At least the noob was trying to be helpful, and not asking annoying redundant questions with his first two posts. Kudos to him
Maybe next he can learn how to read dates..........baby steps

Bricked my phone. Help please

Hey guys. Well i am massively stuck.
I have tried to unlock my Kaiser like I have done before using the tools provided here.
I ran jumpspl on the phone and then tried to unlock the radio. Thus where I have been stuck.
I have not been able to get the procedure past the 0% mark and I seemed to have tried everything to get it out of the SPL.
My screen is white with the RGB colours on saying
top left:
KAIS130
SPL-3.27.0000
CPLD-8
Top right:
RUUNBH
I cant get the fone to boot and it is stuck. I cant get the MTTY thing to connect to my fone and at a lose end. Any help would be amazing...
Thanks
Mike
mikeseaman3000 said:
Hey guys. Well i am massively stuck.
I have tried to unlock my Kaiser like I have done before using the tools provided here.
I ran jumpspl on the phone and then tried to unlock the radio. Thus where I have been stuck.
I have not been able to get the procedure past the 0% mark and I seemed to have tried everything to get it out of the SPL.
My screen is white with the RGB colours on saying
top left:
KAIS130
SPL-3.27.0000
CPLD-8
Top right:
RUUNBH
I cant get the fone to boot and it is stuck. I cant get the MTTY thing to connect to my fone and at a lose end. Any help would be amazing...
Thanks
Mike
Click to expand...
Click to collapse
have you tried flashing a hard-spl?
mikeseaman3000 said:
Hey guys. Well i am massively stuck.
I have tried to unlock my Kaiser like I have done before using the tools provided here.
I ran jumpspl on the phone and then tried to unlock the radio. Thus where I have been stuck.
I have not been able to get the procedure past the 0% mark and I seemed to have tried everything to get it out of the SPL.
My screen is white with the RGB colours on saying
top left:
KAIS130
SPL-3.27.0000
CPLD-8
Top right:
RUUNBH
I cant get the fone to boot and it is stuck. I cant get the MTTY thing to connect to my fone and at a lose end. Any help would be amazing...
Thanks
Mike
Click to expand...
Click to collapse
What happens when you remove the battery and try to re-start the phone? Have you tried to soft re-set?
SPL2.27 is a good sign. Your device needs CID unlocking as it is a preferred process prior to updating the SPL as well as flashing a new cooked ROM. Read some of the stickies and understand the procedure and you will be fine.
A quick note: the HTC Kaiser is an indestructible device. It endures all kinds of software abuse, and will survive the severest Nubie flashing indulgence. So do not worry! you can get it back to normal.
Do the following first:
I would recommend if you see the four colors on the screen and USB at the bottom of the screen, to flash an OEM HTC or AT&T ROM Dated August 2008. This will clear all bad temp files and will render the device to default stage.
XDA-Wiki is your best friend. After that you can CID unlock the device then start flashing cooked ROMs.
Thread closed.
See my hints in my thread where you also posted.
Dave

Categories

Resources