Database Info

ERROR 262 - Bricked phone with Radio Rom Upgrade - SOLVED -

Hi to all,
I have an AT&T TILT HTC 8925,
ROM: 1.57.502.2
RADIO: 1.27.12.11
VE: 22.45.88.07H
Installed the kaiser-HardSPLv1 with no problems.
After this I Flashed (via USB) Q-Mobile_v1.2 ROM, that went perfect. Made a soft reset and then a Hard Reset after this I configured the phone.
After everything was working I made a Radio flash with KAIS Radio Only 1.27.12.17 CustomRUU, all seemed normal until it got to 95%, it suddenly interrupted the update (error 262), and took me to recovery dialog 1-4 steps which I did.
From that moment until know I get the tricolor screen with the following text:
RUUNBH​KAIS 1*0
SPL-1.56.0000
CPLD-8
USB​
Click to expand...
Click to collapse
And when I try to flash ANY ROM, It gets past the tricolor screen, to a white screen with a percentage bar that gets to 0%, after a minute or so the customRUU screen goes to error 262 and I get to the recovery screen, etc...
I run on WinXP SP2, and have already tried several roms with the same result, with the exception of original ATT RUU_Kaiser_CINGULAR_WWE_.exe, it then gets to 1% and displays error code 294 Invalid Vendor ID.
When I tried the MicroSD method with the rom it gets to the tricolor then the "Loading..." screen, and keeps there (I waited for about 30 min)...
There was no SIM or MicroSD card on the phone at the moment of flashing, and I did dump the original ROM to the 4 raw parts as per instructions.
I live waaay out of the countries with AT&T or HTC servicing routes, so I am stuck with it until I fix it, which I know I can do, and to be honest with myself, can't afford to waste the money spent on this thing.
Until now the best similar thing I found about this was with the hermes unbrick phone thread, and I am not sure this works on the KAISER, but to be honest, I get cold sweats to use any more procedures (without reconfirmation) on this as I have a phone that at least still shows "some" signs of life.
After reading days of threads (my eyes are burning) I know the knowledge is within this site, but I need guidance since I am new to this thing (smartphone flashing) although familiar with computers.
Any kind of help will be very appreciated and valued.
Best Regards.
----------------------
As an update, I solved this thing. Thanks for your help.
After seeing that there was some sort of problem with the boot mode screen not showing the kaiser-HardSPL data, I went in that direction. After some suggestions and much trying I decided to download all / any original roms I found in here for my phone (ATT Tilt) then I worked my way from top to bottom based on the versions of the radio.
The one that solved my problem was 1.5.502.3 Radio 1.27.12.11 although strangely it shows on my phone after the successful flashing. 1.5.502.1
Just out of curiosity I went and installed again kaiser-HardSPLv1 and it gets to this text on tricolor screen:
Kais1*0
SPL-.JumpSPL
CPLD-8
Doing a hard reboot (camera button + soft reset) gives me a different screen:
Kais1*0
SPL - 1.56.0000
CPLD-8
Really don't know if this is normal, and after flashing a cooked rom I had to reinstall it (kaiser-HardSPL).
I have now reflashed QMobile rom and have no problems. Although I didn't flashed again new radios
For flashing the Original rom I did make sure of the following steps in addition to normal ones (Just in case)
1) Disconnected fisically from LAN (Unplugged LAN Cable)
2) Disabled all firewall protections
3) Disabled all antivirus and spyware protections
4) Run RUU original files
5) Pray
Thanks again people

I had the same issue (I mean exactly the same). After failing the radio upgrade (Luckily I had my trusty Universal, so I started playing around (MTTY, Radio Roms etc.). The only thing that saved my TytnII was the original ROM!!
ftp://ftp.xda-developers.com/Uploads/Kaiser/Roms/

I just tried it again (See I am not so scared anymore), and received the same results (Radio upgrade fails on 95%).
I have burned the original ROM back and all is well again!

I also can't get past the same screen and try as I might Activesync won't recognise the phone. When going through the recovery process on Kaiser Custom RUU it says its recovered but then when trying to go through the update it sticks on 0% and then says there are communication problems etc.
On the tricloloured screen it says
KAIS130
SPL-1.81.0000
CPLD-8
Will a hard reset do anything?
Any help much appreciated.

Bump
Now managed to boot via MTTY but power off etc returns me to bootloader screen

Looks to me like you guys have had problems flashing hardspl. Your tri-colour screen should have:
KAIS130 MFG (or Kais 120 etc)
SPL-1.0OliPof
CPLD-8
I don't know about the CPLD number but you MUST have the OliPof SPL. Check this after running hardSPL to make sure that it's there before flashing another ROM.
If you have this but still get trouble flashing, try going to the tri-colour screen and then run the kaiser_RUU.exe to upgrade.

http://forum.xda-developers.com/sho...ked. (One without a radio)
- Flash a radio...

i had the same thing with my MDA Vario 3,but with no success finding the original ROM, since I`m from a small country. I`ve tried to reboot to normal screen via MTTY but it gives me the error: Command error . So - now I`m left with two options: to dump and reconstruct an original ROM from the same type of phone or to find what`s wrong with MTTY.
Anyone had a similar problem, I mean with MTTY and command error???
yes, i`ve searched trough the posts regarding this problem but I didn`t find any saying that MTTY gave this error.
any idea?
THX in advance!

Focus on HARD-SPL - get that on the phone and make sure its there.
If you cant get it on try this method:
http://forum.xda-developers.com/showthread.php?t=354061

Martinhdk said:
Focus on HARD-SPL - get that on the phone and make sure its there.
If you cant get it on try this method:
http://forum.xda-developers.com/showthread.php?t=354061
Click to expand...
Click to collapse
if you`re reffering to my problem-how can I copy the JumpSPL1.56-KAIS.exe file and execute it from the phone if I can`t boot it normaly,it always stays in tri-color boot screen?
actually, I`ve bricked my phone with that HardSPL procedure.It was the first step for unlocking. I`ve copied the JumpSPL1.56-KAIS.exe file, executed it and then rebooted and tried to flash with the modified ROM from the jockyw2001`s unlocker. it stopped at 95% and now it seems that it is still CID locked and bricked in boot mode. i`ve already said what MTTY gives as an error.
any idea what may be the problem?

like always:the problem is in RTFM
while i was working on my Kaiser i was doing lots of other things on other computers so i`ve skipped the step with flashing the HardSPL,that`s why all went wrong now,as i`m at home i have more time to read the posts and i`ll try with the jockyw2001`s procedure from the MTTY, with the task8 command.
hope it will help,unless the only solution is to dump the same ROM....
i`ll higly apreciate if anyone has a different solution....
will post results

The problem is that I can't flash the phone with anything be that HardSPL or the original Orange ROM or whatever you care to mention because the PC can't communicate with the device via the USB cable after Activesync ceases to operate. As such everything works up until the % progress bars come on both screens and then they stay at 0% before the communication error message appears.
Funny thing is that the phone is communicating with the PC as USB/Serial alternate depending on whether the cable is plugged in or not and the PC recognises the USB device when its plugged in and when Activesync isn't controlling the situation.

I've been stuck like this with a Hermes but not the Kaiser (yet). As far as I'm aware, you don't need activesync running to run a rom upgrade. If you are in bootloader mode (tricolour screen) you can run the upgrade directly with activesync not connected. If hardspl isn't installed then you should flash the original rom, and if you're unlocked then any rom should do.
Also it might be worth trying the SD card method for flashing. But either way I'd use the original rom and then when you get the phone working again keep trying with HardSPL until it's successful - don't flash any other roms without it.

Laubscherc said:
I had the same issue (I mean exactly the same). After failing the radio upgrade (Luckily I had my trusty Universal, so I started playing around (MTTY, Radio Roms etc.). The only thing that saved my TytnII was the original ROM!!
ftp://ftp.xda-developers.com/Uploads/Kaiser/Roms/
Click to expand...
Click to collapse
Thanks for your help.
I did try other "original" rom I got in here http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
The version corresponding my rom is (1.57.502.2 (radio 1.27.12.11)), however I got the error code 294 Invalid Vendor ID after 1%.
I did try the ftp address you mentioned, but I can't login neither anonymously nor with user & psw for xda-developers.
I would like to try the rom you are referring to, please give me another link to download the file.
Best Regards.

Martinhdk said:
http://forum.xda-developers.com/sho...ardware devices list.
Thanks for your help.:)
Click to expand...
Click to collapse

Stuck in Tri color screen
I have been fighting the same issue for several days. Radio gets to 95% and errors. Then hung up in tri color screen. I used MTTY - "set 14 0" command then "boot" command inMTTY to get the phone to boot. I have had to do this a number of times, sometimes more than once per incident. Hope it works for you too. P.S. once you have a successful flash the phone returns to normal operation until then it will go back to tri color screen on reset. I just flashed a startup splash screen to get mine back to normal.

pennco can you expand in further detail on what you actually did with MTTY cause I have the EXACT same problem....

Tilt Stuck at 3 color screen...Help!

installed hardspl, began flashing, got to 20% then error 262. now get error 262 at 0%.
What can I do?
Screen has RUUNBH in the top right corner.
KAIS1*0
SPL-1.56.0000
CPLD-8

fitdocsr said:
installed hardspl, began flashing, got to 20% then error 262. now get error 262 at 0%.
What can I do?
Screen has RUUNBH in the top right corner.
KAIS1*0
SPL-1.56.0000
CPLD-8
Click to expand...
Click to collapse
While in the tri color screen.
Flash to this ROM.
http://rapidshare.com/files/5340369...adio_sign_22.45.88.07_1.27.11.31_Internal.exe

Yeah, I had a similar problem. The only ROM that worked for me was the newest AT&T ROM (1.61.502.2) that was posted in the Kaiser ROM wiki. All the other ROM's failed (even the same build that was on my device). This was after I was trying to put on the HardSPL to get it unlocked.
I had the White Screen of Death and was testing some new builds of the SPL stuff and got into the 3 color state of doom.
I'm pretty sure this is the ROM I used:
http://forum.xda-developers.com/showthread.php?t=357123
TTFN

Thanks for the replies.
Here is what i ended up doing.
open mtty, press enter, then type boot, enter
got the phone to boot back to windows mobile then ran customruu from there.
I thought I had bricked it, certainly scared me.

I had this problem yesterday. I went through the "recovery" process. This brought me back to the 3 Color screen. From there I clicked the HardSPL exe. Pressed enter, let HardSPL run for a few seconds(the screen didn't change but I could hear the laptop working). Then opened the RUU for any ROM I wanted to install.
This avoided installing an intermediate factory ROM.
This only works one time each time I recovered. If I canceled out of the RUU I had to go through the recovery process again.
1. Unplug USB
2. Remove Battery
3. Wait 3 seconds
4. Install battery
5. Turn on phone
6. Plug in USB
Good Luck!

What is wrong with my phone? Tried to Flash new Rom...Black Screen

Okay. I tried to install one of Dutty's ROM's that can be found here: http://forum.xda-developers.com/showthread.php?t=398271.
I read through all the stickys and FAQ's first. I read Dutty's wiki, the Kaiser wiki, and the flashing new ROM wiki. I followed all of the directions and followed Dutty's instructions to the T.
After installing the HardSPL found here(http://forum.xda-developers.com/showthread.php?t=334679), I backed up all my personal info/data.
Then used the Custom RUU Dutty supplied and proceed through the ROM flashing process. Everything went fine and I got no error messages. But when my phone booted up I got a black screen. I waited but my phone stayed on the black screen. So I pressed the standby button on and off a few times and eventually I wound up with a black screen that had about a million multi-colored speckled dots all over it. And I have been stuck on this screen since. I've tried soft-reseting and hard resetting but nothing is working.
I am Using an ATT Tilt BTW.
Please Help me. My phone is my life so right now I'm feeling like Dionne Farris.....Hopeless....

ahh that sounds like a nightmare... wish i could help

klrob33 said:
Okay. I tried to install one of Dutty's ROM's that can be found here: http://forum.xda-developers.com/showthread.php?t=398271.
I read through all the stickys and FAQ's first. I read Dutty's wiki, the Kaiser wiki, and the flashing new ROM wiki. I followed all of the directions and followed Dutty's instructions to the T.
After installing the HardSPL found here(http://forum.xda-developers.com/showthread.php?t=334679), I backed up all my personal info/data.
Then used the Custom RUU Dutty supplied and proceed through the ROM flashing process. Everything went fine and I got no error messages. But when my phone booted up I got a black screen. I waited but my phone stayed on the black screen. So I pressed the standby button on and off a few times and eventually I wound up with a black screen that had about a million multi-colored speckled dots all over it. And I have been stuck on this screen since. I've tried soft-reseting and hard resetting but nothing is working.
I am Using an ATT Tilt BTW.
Please Help me. My phone is my life so right now I'm feeling like Dionne Farris.....Hopeless....
Click to expand...
Click to collapse
can you get into bootloader mode?
hold down power and camera button while inserting stylus it should introduce you to the tri color screen. Please tell us what it states. You may have just experienced a bad flash or you have the radio from hell installed on your device

redbandana said:
can you get into bootloader mode?
hold down power and camera button while inserting stylus it should introduce you to the tri color screen. Please tell us what it states. You may have just experienced a bad flash or you have the radio from hell installed on your device
Click to expand...
Click to collapse
Yes I can get to Bootloader mode.
In the red bar it says:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
And Serial at the bottom in the white bar where USB normaly would be.

klrob33 said:
Yes I can get to Bootloader mode.
In the red bar it says:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
And Serial at the bottom in the white bar where USB normaly would be.
Click to expand...
Click to collapse
ok soft reset your phone and when it starts up does something like this appear in red text?
r 1.65.20.29
g 25.88.40.04w
d 3.29.xx.xx
please tell me what it says after R

R- 1.58.25.17

klrob33 said:
R- 1.58.25.17
Click to expand...
Click to collapse
well it appears to be a bad flash. unplug your device from the usb cable, restart your computer, and flash again.
Hopefully after your computer restarts it will recognize the device as being connected. If it doesn't just double click on your windows mobile device center icon and it should connect. After connecting just reflash the rom
edit

I had the same problem, what i did was read all through the thread of the ROM or while inside the thread i use the search function and type in the keywords like "blank screen" it happened to me exactly, but i didnt bother to post since i found the answer, 1 user said flash it to WM 6.1 i did exactly that and it helped! some said not necessary, but i didnt see that instruction so i flashed the 6.1 blindly and fortunately it worked...
here is the thread
http://forum.xda-developers.com/showthread.php?t=375583&page=30
on the search function type black screen and you should get and idea what you need to do...

redbandana said:
well it appears to be a bad flash. unplug your device from the usb cable, restart your computer, and flash again.
Hopefully after your computer restarts it will recognize the device as being connected. If it doesn't just double click on your windows mobile device center icon and it should connect. After connecting just reflash the rom
edit
Click to expand...
Click to collapse
I tried that and It different work. I'm trying a whole new ROM now and I hope it works.

Problem solved.
Thanks to everybody for their help.
I just used a different ROM and everything worked perfectly. I guess that ROM just didn't want to work with my phone. But it's okay. The ROM I'm using now is perfect.

Screen turn black after flash

I used Olipof to HardSPL.
The boot (tri-color) show me the information below:
- KAS1*0 MFG
- SPL-1.0.OliPof
- CPLD-8
I'm still stuck after OS boot. Windows can not be shown on the screen after AT&T and 3G appeared (Im using original Rom of AT&T). The screen turn black then...
What should I do

Lagz0ne said:
I used Olipof to HardSPL.
The boot (tri-color) show me the information below:
- KAS1*0 MFG
- SPL-1.0.OliPof
- CPLD-8
I'm still stuck after OS boot. Windows can not be shown on the screen after AT&T and 3G appeared (Im using original Rom of AT&T). The screen turn black then...
What should I do
Click to expand...
Click to collapse
flash the phone with a ROM that includes a compatible radio - like L26 or Sleuth. If you feel you've bricked your phone, I'll give you $50 for it.

As a complete noob I ran into this as well. There are threads on here that describe the solution so you may need to search for it(spoken like a true veteran ). I flashed Dutty's 6.1 rom and continued on my merry way.
No biggy, just search for "black screen".
...2nd in line if you bricked it.

<startnoob_mode>
.. searching "blank screen"
.. showing results 1 to 25 of 204. Search took 1.29 seconds.
.. (looking for something interesting...)
.. (looking)
.. (looking)
.. (still looking)
.. ah! something interesting!
.. clicking This how i bought my 8925 from black screen
..
<endnoob_mode>

Nice XML but actually it should be </startnoob_mode>
Thanks all you guy. Actually I've been affected buy white screen error .

Please Help! TYTN II from WM6.0 To WM6.1

I have read through endless posts and stickies.. I still can't figure out what the correct procedure is for updating my TYTN II from WM6.0 to WM6.1
I would greatly appreciate it, if someone would lay it out step my step
I tried to flash with the WM6.1 update, it said there was a vender error.
I tried flashing with HardSPL 3.28 and it stops at 0% and says there is there is a communication error, and to click next to perform the recovery. I perform the recovery, after removing the battery and putting it back in, the phone starts up normal.
I tried the white screen solution.. it reaches the three coloured display with USB and just sits there.. i eventually reboot the phone.. and it starts back up normally..
but none of the flashing procedures have worked yet..
I used the files found Here for the white screen problem.
I don't know what else to try..
Direct update - Invalid Vendor ID
HardSPL 3.28 - Communication Error
JumpSPL - Does nothing...
What am i missing?

Puff1911 said:
What am i missing?
Click to expand...
Click to collapse
Interpreation and sense of what you are reading.

http://hpcmonex.net/olipro/KaiserUnlocker.zip
That is the link to the Kaiser Unlocker by Olipro. It Hard-SPL's and SIM Unlocks. If you do not need the sim unlock simply flash to a different ROM after the first step.

Thanks socalkevin21 for providing a usable response

Not a problem, let me know if you have any issues.

The software says to unplug the USB connection as soon as the screen turns to the three coloured screen.
when i plug back in, the progress bar waits a couple seconds then jumps directly to 100%.. is that correct?
The phone reboots, and starts back up as normal.. but the same version ROM is still there..

Puff1911 said:
The software says to unplug the USB connection as soon as the screen turns to the three coloured screen.
when i plug back in, the progress bar waits a couple seconds then jumps directly to 100%.. is that correct?
The phone reboots, and starts back up as normal.. but the same version ROM is still there..
Click to expand...
Click to collapse
enter bootloader (press and hold the camera button all the way while pushing the stylus into the reset hole)
you should now be at a tri-color screen
what does this screen say?

KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
when I click on Unlock Radio, it says "incompatible device"
Is that also normal?
Do i need to patch the radio as well?

wooooo!!! got it! i eventually got it to update the radio by clicking the button over and over..
I didn't get to unlock the phone (step 3).. but after i tried to update to windows mobile 6.1.. and it worked!
Thanks socalkevin21 and mbarvian!!

Well my device runs a lot faster.. but also sticks a helluva lot more!
Also my camera doesn't show anything, it takes pictures fine.. but there is no live display.. anyone having that problem?
And i also lost Voice Commander.. anyone have the install files for that?
**Fixed the camera problem. I had installed the HTC camera patch... Problem solved after removing it.**

Puff1911 said:
Well my device runs a lot faster.. but also sticks a helluva lot more!
Also my camera doesn't show anything, it takes pictures fine.. but there is no live display.. anyone having that problem?
And i also lost Voice Commander.. anyone have the install files for that?
**Fixed the camera problem. I had installed the HTC camera patch... Problem solved after removing it.**
Click to expand...
Click to collapse
Try a new HardSPL.
WM6.1 freezes sometimes with the OliPof 1.0 Hard SPL.
All the latest Hard SPL's are here: http://forum.xda-developers.com/showthread.php?t=396922
There are no other differences between 1 and 3.* other than the version number - they both work the same (oh and no MFG in 3.*, but you won't notice that)
Ta
Dave