Related
First, my palm 750 was having the problem that it got stuck like always, and when it finally started working, i had no signal at all, radio on, turned off and back on, hard reset, soft reset, nothing. So then I saw that there was WM6 and upgrading sounded like a good idea. Started looking for the rom and i found the voda WM6 rom, followed the instructions and when it was upgrading the battery felt cuz I didn't put back the cover (my bad). After that, I tried to turn on the fone and all I got is the Bootloader screen, have read a lot and all the answers are to format the card to fat32, or to switch computers, I've used like 3 different cards, checked on 3 pc's, used another card reader and all I got is the boot screen, if I put the card in it says loading, press the end call botton, start updating and then got stuck after splash1 and bootloader says ok. What I'm wondering is if the it is a hardware problem was before the update I had no signal, and now it got stuck on the gsm part of the update. Any Ideas?? this is a really expensive paperweight!!!!!
A couple thoughts...first, when it gets to the GSM portion of the flash it takes significantly longer than the others, so you might just need to be a bit more patient. Run it again and leave it alone for 10 minutes.
If you can get to the bootloader screen, your device is not bricked. You didn't mention what carrier your device is from..is it a Vodafone device? If so, you might be able to just connect the device to your PC while it's in bootloader mode and run the full Vodafone updater on your PC. There's a chance that this method might not work if a partial flash has left your device in a state that the PC based updater can't identify.
pirulino23 said:
First, my palm 750 was having the problem that it got stuck like always, and when it finally started working, i had no signal at all, radio on, turned off and back on, hard reset, soft reset, nothing. So then I saw that there was WM6 and upgrading sounded like a good idea. Started looking for the rom and i found the voda WM6 rom, followed the instructions and when it was upgrading the battery felt cuz I didn't put back the cover (my bad). After that, I tried to turn on the fone and all I got is the Bootloader screen, have read a lot and all the answers are to format the card to fat32, or to switch computers, I've used like 3 different cards, checked on 3 pc's, used another card reader and all I got is the boot screen, if I put the card in it says loading, press the end call botton, start updating and then got stuck after splash1 and bootloader says ok. What I'm wondering is if the it is a hardware problem was before the update I had no signal, and now it got stuck on the gsm part of the update. Any Ideas?? this is a really expensive paperweight!!!!!
Click to expand...
Click to collapse
Thanks, and well it is a Cingular Treo, and I left the updater running several times for more than 3, 4 hours until the battery run out, and well, keep being stuck at gsm part, tried the tool that is on the update but after some % it got disconnected, any ideas???
im no expert. but if your using it with cingular (att) and you used a voda rom, i dont know how it would work in the first place without some sort of cid unlock? correct me if im wrong.
anyway. I would try that leaked att rom it it were me.
kapster said:
im no expert. but if your using it with cingular (att) and you used a voda rom, i dont know how it would work in the first place without some sort of cid unlock? correct me if im wrong.
anyway. I would try that leaked att rom it it were me.
Click to expand...
Click to collapse
Well First never do a rom update off the battery second I have a att/Cingular 750 had leaked att on it ran fine then moved to the voda rom still fine
If the ATT rom doesnt work search for a WM5 Rom I think someone said it was posted in here. If that doesnt work, the first rom update I screwed up killed my device I called ATT said I tried to install the audio update and it killed my device they sent a new one and then i up'ed the ATT rom GL.
mtty perhaps?
[SIZE=+2]SOLVED[/SIZE]
Thanks to jockyw2001 this is no longer an issue. Please see his sticky thread for the fix and directions...
[size=+1]http://forum.xda-developers.com/showthread.php?t=354061[/size]
Hello all...
First off, let me start by saying that this is not my device, it's a friend's at work... I have done the same process on pretty much all my friends' Tilts (like 10 or 12 of them) and haven't seen this issue until today.
When I try to install HardSPL to the device I get the normal pop-ups on the screen about security and then Pof's "continue" message and when it is supposed to go to the JumpSPL (tri-color) screen all I get is a white screen. This happens on my device too for just a moment before I get the tri-color but his device just sits there...
The plus side is that is doesn't actually do anything to the device, it boots fine with a soft reset.
So far I've tried flashing the AKU 0.4.4 ROM which does install so it doesn't appear to be a software issue (at least not OS level). I have also tried mtty and issuing a 'task 2a' but nothing happens I just get the
cmd>
prompt back after running it, no output to the screen whatsoever.
Anyways...I'm just starting this thread to see if there are any other NEW Tilt owners (or Kaiser in general) that might be experiencing this problem. And if you know of a fix...
Cheers,
From many years of working on people's computers, phones, etc. let me give you a friendly tip:
Don't ever touch someone else's device to make modifications to it.
By doing so you become the sole person responsible - the sole person who will be blamed 6 months down the road when something doesn't work, they have warranty issues, etc.
I've taken on the method of giving people everything they need, helping get them set up, explaining the risk, then making them push the button.
Just a thought..
appreciate the feedback... but I don't mind helping my friends and I let them know the risks prior to any mods.
There are those here that don't want their phones "upgraded" and I don't help them. Those who do and don't want to research, come to me.
Back on topic though... has anyone else seen this behavior?
I saw several threads in the Hermes forum concerning "white screen" but they were after flashing ROMs... this issue is before HardSPL actually gets flashed.
Thanks again!
I wonder if maybe your friend has a newer revision or something that includes a new bootloader.
Can you enter the boorloader manually and see what version it is?
gthing said:
I wonder if maybe your friend has a newer revision or something that includes a new bootloader.
Can you enter the boorloader manually and see what version it is?
Click to expand...
Click to collapse
Yah I was thinking that as well... I did check it and it showed:
KAIS1*0
SPL-1.56.0000
CPLD-8
Before I installed AKU 0.4.4... after which it now reads:
KAIS1*0
SPL-1.93.0000
CPLD-8
... still no love but at least its working, would like to get HardSPL on it though.
Interesting....
You might try hitting up the irc channel - Oli usually hangs out in there and might have some insight.
I had this on my TYTN - and that was due to some hardware failures or wrong .net version. Try to install the newest .net and see..
Martinhdk said:
I had this on my TYTN - and that was due to some hardware failures or wrong .net version. Try to install the newest .net and see..
Click to expand...
Click to collapse
well I wouldn't think it was .net since I managed to flash the AKU0.4.4 ROM (should be a new .net or at least a "reinstall" there). I tried it anyways and installed .NET CF 3.5 ... still no love, same white screen issue when running SSPL-KAIS.exe
I'll see if I can catch Oli on IRC. Can you point me to the server and channel?
sirsycho said:
well I wouldn't think it was .net since I managed to flash the AKU0.4.4 ROM (should be a new .net or at least a "reinstall" there). I tried it anyways and installed .NET CF 3.5 ... still no love, same white screen issue when running SSPL-KAIS.exe
I'll see if I can catch Oli on IRC. Can you point me to the server and channel?
Click to expand...
Click to collapse
irc.freenode.net
#xda-devs
Sirsycho... i answered you in the original thread. I had similar issue however i needed to remove the SIM card and the SD card. Then the white screen disappeared and the tri color one appeared. try removing the SIM and SD cards b4 installing. Also remember the issue with the AntiVirus...
asfoor said:
Sirsycho... i answered you in the original thread. I had similar issue however i needed to remove the SIM card and the SD card. Then the white screen disappeared and the tri color one appeared. try removing the SIM and SD cards b4 installing. Also remember the issue with the AntiVirus...
Click to expand...
Click to collapse
Good idea asfoor... I did actually remove the SD card but for some reason didn't think to remove the SIM. I'm home now and will have another opportunity to try again with his phone tomorrow. I'll post my results then.
Thanks again for the tip... makes me feel silly that I didn't think of it though
alright... I took out both SIM and SD this time, but still just the white screen. I really wish I could get the task 2a to work, I think it's probably a bad block issue that JumpSPL is attempting to access.
I'm having the exact same issue. I've read and searched, only finding your thread. Just hangs forever on the white screen, never getting to tricolor.
Anyone else having this issue?
ROM Version: 1.57.502.2
ROM Date: 08/25/07
Radio Version: 1.27.12.11
Protocol Version: 22.45.88.07H
plirky said:
I'm having the exact same issue. I've read and searched, only finding your thread. Just hangs forever on the white screen, never getting to tricolor.
Anyone else having this issue?
ROM Version: 1.57.502.2
ROM Date: 08/25/07
Radio Version: 1.27.12.11
Protocol Version: 22.45.88.07H
Click to expand...
Click to collapse
when did you get your device?
Out of sheer curiosity, check the manufacture date:
remove back cover... date should be just above the battery in the following format: MMDDYY
For example, mine which does work and which I have HardSPL on reports: 061107
I will get the date from the "broken" one tomorrow.
I just got it two days ago.
The manufacture date on mine is 080907.
weird...
Anyone else have any ideas?
"When I try to install HardSPL to the device I get the normal pop-ups on the screen about security and then Pof's "continue" message and when it is supposed to go to the JumpSPL (tri-color) screen all I get is a white screen."
Mine is 080907 and I remembered clearly that when I first tried the hardspl it frozed, so I just take the battery out and redid it again and it worked.. I also noticed I didn't follow the instruction as it was told earlier the first time: unplug the cable and replug it back in etc etc.
But right now I'm using Dutty's Tilt Rom Beta 2 and loving every minute of it. (I did disable the cube but kept everything else the same) so I can use transcriber.
So far, since a week ago, I am LOVING every minute of it.
Yeah...
I've got one of these bad boys, just came Friday with date of 181007 (which suggests it is DDMMYY, not MMDDYY) Code after date is (RC01). My previous Tilt (returned for continuous vibration glitch) had (RB01) code. I've tried all the suggestions here... no luck. Damn White screen forever....
NOT fun.
plirky said:
I just got it two days ago.
The manufacture date on mine is 080907.
weird...
Click to expand...
Click to collapse
What is inside the parenthesis just after the date of manufacture? (RB01), (RC01), other?
I'm having the same issue here. Just got the phone a week ago. MFG date: 181007. Any ideas would but very much appreciated.
dantegl36 said:
I'm having the same issue here. Just got the phone a week ago. MFG date: 181007. Any ideas would but very much appreciated.
Click to expand...
Click to collapse
Yep Same issue here, Got mine a few days ago: 181007 (RC01)
This sucks....
Hi guys, first of all I just want to say thank you for this forum.. I ran into it a while back and was inspired to buy a kaiser just because of you guys. I have an iphone right now and I really want to replace it with something that has i don't know user accessible memory, MS office, GPS and the list goes on so I bout an At&t 8925, I got a good price on it and was very happy to finally able to get rid of the iphone
anyway I received the phone a few days ago and proceeded to do a sim unlock to use it with t-mobile after playing with it for a little while, I have already read the wiki, and lot of posts and searches..
I dnloaded this http://forum.xda-developers.com/showthread.php?t=375583 and plugged in the phone made sure activesynk connected and flollowed the instructions...
It went through the first step (hard spl) without a problem and I think the second step went well also. After that I begain the third step and the program froze, I waited for almost an hour just to be sure (windows also said it was 'not responding') I finally had no choice but to restart my computer, (its vista)
Anyway I pressed the power button on the phone and the phone acts like its booting up, I see the at&t screen, then it goes to the 3g screen and It just goes to a blank, black screen. I am still able to connect it to my computer and access the phone. I can access the 'boot loader' red blue green screen
I did a soft reset and tried to reload the unlocker porgram but nothing happens, I am stuck and I havent found out what to do through my searches can you guys help me out I am really new to this phone
I even took the time to downgrade my computer from vista to XP (finding all my drivers was a ***** since my computer was shipped with vista) but I found them one by one and still no luck loading the unlocker
one thing I did notice was that the bootloader screen now says "security unlocked" on top, not sure if It did that before
Thanks for all the help
Thanks
all you have to do to fix your phone is flash a new rom onto it. just open the boot loader and run the ruu and it should fix the problem
that's because you need to install a wm6.1 rom on your phone to use this unlocker. you would have found the answer if you read the thread
Olipro said:
hence why I wrote a message box on Step 2 stating "you may need to upgrade your phone to WM6.1"
****ing idiots.
Click to expand...
Click to collapse
oh **** how did i miss that... going to try another rom, i'll let you guys know how it goes
thanks
tman6919 said:
oh **** how did i miss that... going to try another rom, i'll let you guys know how it goes
thanks
Click to expand...
Click to collapse
Thread done. Please remember to read through all instructions etc...
I know, I know, there are loads of threads like this but I must be lacking something in the brains department as I've spent the last 6 days (since I got my orange tytn) reading this forum trying to understand how to unlock the thing without turning it into a brick and then to flash a rom and radio.
Everything I read on here has people contradicting other people and I end up not having a clue what to do in the end.
HEELLLLP!!!
To confuse matters even more I thought I'd got it sussed and then read about roms having/not having a CUBE!!!! WTF???? I then gave up and started typing this thread...
Here's what I think......and PLEASE correct me or agree with me....
Firstly I seem to be stumbling at the first hurdle since I have an orange tytn and that it seems is the worse to have for some reason???
I thought I'd start off simply by using the kaiser simunlocker to unlock the phone (by jocky) but then came across something called hardspl with all its variances, so OK lets go with the flow and dismiss the hardspl step for now assuming I can do it and read on...
Assuming I could ever find a program that makes a backup of the rom I've got I'd carry on with the unlocker until I get to the step (step 10) that says download the original radio..............this of course doesn't exist (1.27.14.32) so I look for a proggy that downloads the radio to use at this point. Here's where I come unstuck again.........no proggy!!
At this point I must assume that this may not be possible on the model I've got if I want to be sure I can make it original again.
Could someone please confirm this so I can accept the fact that I have to use what came with the phone and save myself a few hours a night getting nowhere...
Sorry for my rant but I'm frustrated that my old brain can't figure this out and giving up seems to be the only option. I completely understand that I'll get flamed for this since I'm a noobie and asking again what numerous otheres have asked but I accept that...
I have great respect for all you guys that can actually understand this on first reading and especially the people who produce this stuff....
Thanks again folks
familyguy said:
I know, I know, there are loads of threads like this but I must be lacking something in the brains department as I've spent the last 6 days (since I got my orange tytn) reading this forum trying to understand how to unlock the thing without turning it into a brick and then to flash a rom and radio.
Everything I read on here has people contradicting other people and I end up not having a clue what to do in the end.
HEELLLLP!!!
To confuse matters even more I thought I'd got it sussed and then read about roms having/not having a CUBE!!!! WTF???? I then gave up and started typing this thread...
Here's what I think......and PLEASE correct me or agree with me....
Firstly I seem to be stumbling at the first hurdle since I have an orange tytn and that it seems is the worse to have for some reason???
I thought I'd start off simply by using the kaiser simunlocker to unlock the phone (by jocky) but then came across something called hardspl with all its variances, so OK lets go with the flow and dismiss the hardspl step for now assuming I can do it and read on...
Assuming I could ever find a program that makes a backup of the rom I've got I'd carry on with the unlocker until I get to the step (step 10) that says download the original radio..............this of course doesn't exist (1.27.14.32) so I look for a proggy that downloads the radio to use at this point. Here's where I come unstuck again.........no proggy!!
At this point I must assume that this may not be possible on the model I've got if I want to be sure I can make it original again.
Could someone please confirm this so I can accept the fact that I have to use what came with the phone and save myself a few hours a night getting nowhere...
Sorry for my rant but I'm frustrated that my old brain can't figure this out and giving up seems to be the only option. I completely understand that I'll get flamed for this since I'm a noobie and asking again what numerous otheres have asked but I accept that...
I have great respect for all you guys that can actually understand this on first reading and especially the people who produce this stuff....
Thanks again folks
Click to expand...
Click to collapse
Screw what everyone tells you and start with the link above this thread. Actually the second thread on this page. I think I am one of the oldest around here so its not your "old" brain. _Alex_ has gone to great length to get all of the information you need in one place. Start with his sticky. Good luck.
hello, lots of stuff to learn, first thing, which sounds like you did is read, next hard SPL
see the 2nd sticky in the forum,
go down to kaiser wiki, then rom tools wiki, the 3rd choice, hard SPL cid unlock, read carefully and install, once completed, now your phone is ready to flash roms, (for Kaiser) most come with radio or recommend radios to use and not use. if you have problems with hard spl then use the wiki again to troubleshoot and the first 2 stickys
im out
just sell your kaiser and stick to a razor......lol.....j/k....just listen to p1tater...hes right!!
Hey family guy,
A few months back I got an Orange TYTN II just like you. I read for about a week on here untill I felt confident enough in the steps needed to flash a new ROM. First off I Hard SPL and then went for Dutty V3 ROM which was perfect untill I then felt clever enough to flash a new ROM a few weeks later. Due to not sim unlocking correctly the first time around, upon a new radio being flashed to the phone It locked my SIM.. untill I found out the true way to SIM unlock the phone.
Once you have Hard Spl and SIM unlocked you are well away. I know at this point you are probably feeling pretty confused with all this but believe me it is well worth it in the end.
Oh and FYI.... I can confirm that there is an Orange original Rom on here and a few compatible radios should you ever need to revert back to them for some reason as I had to do this myself at one point when trying to work out where I was having issues with something.
All the best
Chris
P.s are we going to start the "who is the oldest contest yet?"
c.b said:
P.s are we going to start the "who is the oldest contest yet?"
Click to expand...
Click to collapse
There's been one around for a while:
http://forum.xda-developers.com/showthread.php?t=325426
but then they do say that memory's the first thing to go, so I'll forgive you!
Confused Stu said:
There's been one around for a while:
http://forum.xda-developers.com/showthread.php?t=325426
but then they do say that memory's the first thing to go, so I'll forgive you!
Click to expand...
Click to collapse
PMSL....That's where it went, I knew I had left it somewhere. Now where are my damn glasses I can't read a thing.
Unlock your Orange Kaiser
Here's my experience ..
1. Basically HardSPL your Tytn II to facilitate a cooked ROM that can be 'sim unlocked'
2. Install the Cooked Rom
3. Run the Sim unlock generator code
4. Phone is *UNLOCKED !*
5. Install a ROM of your choice
6. Install a Radio of your choice
Here's the stuff I used:
READ ALL THE POSTS - READ ALL THE POSTS !!
** USE WINDOWS XP OS with Activesync!! **
1. HTC Kaiser Hard-SPL v1 - CID Unlock & Flash any ROM to your device
You will know you got it right when it says either 1.0.HardSPL or 1.0.OliPof.
NOTE: I had problems here and had to force it with JumpSPL1.93 because HardSPL would not install.
2+3. I used Jockyw2001 Kaiser Sim Unlocker v0.1
NOTE:
> The file has three steps ... 1, 2 & 3 so you can't go wrong:
> Step 1. Installs the 'patched' Radio
> Step 2. Generates the key code for unlocking (on your PC) which you enter into the Tytn.
> Step 3. Installs a replacement radio
4. My code was a series of numbers that I had to type into the screen.
5+6. Read my signature for what I'm using today (it changes)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
All instructions are on screen with prompts.
I sweated for days before I chanced it and it took me about 15 minutes from start to finish but you end up with a pucka HTC looking Tytn II and not the Orange variant.
A few important pointers from the bit I learned:
1. You cannot do this on a WM6.1 Tytn II, you have to go down to WM6.0 - As mine was WM6.0 it didn't matter.
2. Vista is a ***** for doing this and you have enough things to think about without the PC's OS .. USE XP !!
3. HardSPL once done, the Tytn II is clear for all future ROM + Radio upgrades.
4. Bootloader = Power button + Camera button + Reset with stylus
5. Hard reset is Left softkey + Right softkey + Reset with stylus
6. Always Hard reset after blowing any new ROM before using.
7. Backup all your contacts etc. to your SD card with PIM Backup 2.8 before you do anything.
8. Remove the SD card before you begin.
9. The 'Cube' isn't always included in the ROM's - I use this CUBE
10. Most Roms come with their own 'loader' called 'Kaiser_RUU' so you don't have too much to think about.
11. Stick your Radio and ROM information in your signature, you never know when you may want to go back and forget what you had installed ;-)
12. Installing a new radio on a phone that isn't SIM Unlocked will result in a LOCKED TO ALL NETWORKS phone - So SIM Unlock it !!
Enjoy
PS. Let me know if you can't find the files you need.
SIM Unlocker Software HERE
PPS. Before you unlock your Orange can you pop over to this thread and answer Rabdo's question - Thanks.
ajs007 said:
Here's my experience ..
12. Installing a new radio on a phone that isn't SIM Unlocked will result in a LOCKED TO ALL NETWORKS phone - So SIM Unlock it !!
this thread and answer Rabdo's question - Thanks.
Click to expand...
Click to collapse
Hey I have a question about this point - I've never SIM unlocked my phone and have flashed about 6 ROMS, and various radios and never had a problem. All I did was run hardSpl, then started flashing.
So what I'm asking is are you sure of this point?
Mods Please Close
This is a useless thread. Mods please close this thread.
P1Tater said:
Screw what everyone tells you and start with the link above this thread. Actually the second thread on this page. I think I am one of the oldest around here so its not your "old" brain. _Alex_ has gone to great length to get all of the information you need in one place. Start with his sticky. Good luck.
Click to expand...
Click to collapse
Oldest around here your a Matt Serra fan I swore you were like 25.
-McMex
mattarse said:
Hey I have a question about this point - I've never SIM unlocked my phone and have flashed about 6 ROMS, and various radios and never had a problem. All I did was run hardSpl, then started flashing.
So what I'm asking is are you sure of this point?
Click to expand...
Click to collapse
I have heard before that Orange Kaiser's are a little different to other networks and need to be SIM-unlocked before they can use a different network.
Confused Stu said:
I have heard before that Orange Kaiser's are a little different to other networks and need to be SIM-unlocked before they can use a different network.
Click to expand...
Click to collapse
Ok thanks, that would make sense then.
Cheers!
Hi all and thanks for your comments advice and encouragement..........just quickly looking at the old age thread I am one of the oldest at 47!!
The thing about this thread is that it's happened again and there are only 13 posts!!
There's been contradiction about the orange tytn above. Some peeps say it needs to be unlocked (and that they've done it but don't mention what radio they're using), and some peeps say it doesn't need to be unlocked!?!?!?
There is my confusion and my hesitation to do anything in case I lock the sim out completely. That I can't have as I need the phone at all times to get in toch with my kids (humans or small goats depending on what your state of mind is!).
Here is what I think I should do...
1.) Use hardspl to unlock something (not sure what at the mo) so that I am able to flash
2.) Unlock the SIM lock using kaiser sim unlocker (or not! jury is out, but not sure which radio to use so scared of brickifying it)
3.) Flash my choice of rom (but not sure if I have to then flash a radio or if the radio is included in the rom)
That's about all my poor tired OLD.......VERY OLD brains can figure out and there are enough 'I don't knows' there to stop me in my tracks...
I'll keep reading though but in the meantime I could do with gleaning info from someone who is in the UK on orange and maybe has a recent model...
TTFN
familyguy said:
I'll keep reading though but in the meantime I could do with gleaning info from someone who is in the UK on orange and maybe has a recent model...
TTFN
Click to expand...
Click to collapse
I'll be 48 in August, so it's not just the Youngsters who play with the 'phones.
(Does that make me the oldest ?)
I bought the TytnII from the Orange Shop in Leicester just before Christmas but didn't have the bottle to unlock it for months ... Main reason was the unlocking 4 months ago was £20 !! and i didn't want to brick it either.
I spotted someone selling the unlocking service on ebay about a month ago, so I knew someone had cracked it here (and some cheapskate was selling the service.)
Feel free to private message me, if you need to we can talk it through over the phone.
Alan.
familyguy said:
There's been contradiction about the orange tytn above. Some peeps say it needs to be unlocked (and that they've done it but don't mention what radio they're using), and some peeps say it doesn't need to be unlocked!?!?!?
TTFN
Click to expand...
Click to collapse
I may have added to the confusion - I do not have an Orange phone, adn was questioning whether you need to SIM unlock the phone b/c I hadn't. Later it was pointed out that Orange phones may be different and need to be.
mattarse
Greetings to all...........and a damn good weekend to everyone!!
mattarse you simply added to the confusion in my mind............for other it was probably very clear
ajs007, I will PM you and perhaps a quick chat to get me up and running would be great!
One thing I do know though..........when (yes, I've gone from if to when) I get more knowledable about this I'll be one of the first peeps there to help anyone out if I can!
After a long chat with ajs007 (for which I am very grateful) I felt I had the confidence to go ahead and install hardspl using the jumpspl route.
My tale of woe follows as it was unsuccessful every time...
I followed jockys instructions,
1a. download the 5 attached files
1b. connect your PC to phone with a USB cable
2. REMOVE SIM and SD CARDS !!
3. copy JumpSPL1.56-KAIS.exe to your device and run it (make sure the USB cable is still connected). If you still get a white screen then reset your device and now try JumpSPL1.93-KAIS.exe
4. after a few seconds "USB" appears on the phone display
5. unplug and replug the usb cable
6. deselect "Allow USB connections" in Activesync connection settings
7. now flash hardSPL (run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC)
After step 3 (for both 1.56 & 1.93) I get the tri-colour screen (not mentioned above) shortly followed by 'USB' on the white at the bottom (step 4).
(I guess this makes it a quad colour screen instead of
I then did step 5 and step 6 as above and moved on to step 7 to run kaisercustomruu.exe.
I then get a screen which says verifying phone settings and a further screen which has 'current info about your pda phone:' and lists nothing!!
Another line that says 'image version:' and has nothing listed and yet another line that says 'select from below:' and has nothing next to it!?!?!?!?
There is a button that says update the current ROM version but I dare not press it if it is going to update with nothing!!!??
On top of all that I read contradiction again where the instructions above state that you must deselect 'allow usb connections' yet when you run kaisercustomruu.exe it states that you must have an activesync connection....
I'm now really confused and convinced it just isn't to be. Sorry Alan it did sound so easy when you explained it but there must be something different about my phone.........I'm going to throw myself or the phone or both of us off a tall building.............now Im totally depressed
Exit stage left feeling very sorry for oneself...
Looks like everything was A.O.K. for flashing..
IMPORTANT ** You didn't say if you had SPL xxx PoF on the Tri Screen ?
I didn't have any reference to a ROM on the install screen but it worked, probably because the ROM was in the same directory and it didn't need to look anywhere ....
I think (but I'm not 100%) the activesync USB connection is an XP v. Vista thing, and you do need USB connection in XP.
In summary, if you did have SPL xxx PoF on the Tri Screen you should be good to go.
From totally & utterly confused to successfully running Dutty's 6.1!!
Lots of bonus points and many thanks to AJS007 for allowing me to bother him with all my questions and lack of confidence.
Here's my tale...
Firstly I tried to install hardspl running from my PC and a USB cable but I got the infamous white screen!
I then followed the instructions for using jumpspl version 1.53 (for some reason the instructions I read didn't say remove and re-inset battery therefore I didn't do that bit!).
I got to the bit where 'USB' appears on the screen and pulled out the cable then re-inserted it. I have no idea why you do this but I did it. When I pulled the cable out the screen had 'Serial' on it and when I re-inserted it, it went back to 'USB'
I carried on to the next step and unchecked the 'Allow USB Connections' in Activesync (again I have no idea why you do this) and went on to run 'kaisercustomruu.exe'
Here's where I hesitated and got stuck. The program started on the PC and got to a point where it interrogated the phone, shortly after that I was presented with another screen that waited for my input ready to 'Update' but I hesitated since there was no information listed under 'Image Version:' and 'Select from below:'.
I wasn't sure what to do here and cancelled the whole thing in case I bricked it
After further investigation, more reading and speaking once again to my mentor AJS007, I decided to go ahead and throw what caution I had left to the wind, so I pressed the 'Update' button.
After a few more screens I got to the point of no return and gritted my teeth.........nothing happened........I disconnected and re-connected and tried again..........nothing again............after a third time though (and I don't know why) it burst into life and I got the 'percentage screen'.
At this point I did think I had trashed it but plodded on regardless in the hope that I hadn't and everything would be OK. Thankfully it was and on entering the bootloader screen I saw 'olipof'..............all was well
This gave me the extra bit of confidence I needed to go through the unlock procedure and then on to flash Dutty's latest. I did get to the point where I had to enter the unlock code and it took 2 attempts to accept it for some reason........I can't explain that either!!
It was all in all a stressful time and involved a lot of pacing up and down when the ROM was flashing, taking what seemed to be hours to complete and slowing down to an almost stop at certain points, but in the end it did all work and I am now left with a transformed T2, but with the following little problems,
1.) My bluetooth headset has to be paired every time I want to use it!
2.) When I go to re-calibrate the screen (with the cross hair) it freezes up and I have to do a soft reset.
3.) My screen 'tap' noises have disappeared (except when I press the 'start' button)
I haven't tried to reflash the radio to see if that will take care of the bluetooth issue yet but I intend to do so in the next few days.
For anyone that's interested I'm using the radio ROM that was included in Dutty's latest build (WM6.1_5.2.19209) which is 1.58.16.27.
Finally, once again my thanks to AJS007 who went to the trouble of helping me in my few hours of need.
If anyone new here would like to ask me any questions about my noobie experience please don't hold back!!
Hello, I have an Axim X51v that I bought off someone who didn't want to deal with it anymore. Anyway when you turn it on it hangs at the dell logo or sometimes at the windows start up logo, rarely it makes it into windows but it freezes up after a little while. I've tried flashing several different roms on it (so did the previous owner) but each time it's the same result. I've checked diagnostics mode (record+power+reset) and everything seems to check out (flash has a green zero) and every time I flash a rom it makes it through without any problems. Also the bootloader is a10_g3 is this version known to be unstable? Could it be flashed wrong? That's the only thing I can really think of.
You know this forum is for HTC devices?
Im not familiar with Dell PDA's but i cant imagine flashing roms willy nilly will work on a dell which are designed for HTC devices. Give me a link for the ROM which you are currently trying to use.
Have you tried flashing original rom back on, thats wm5 yes?
Yeah I know it's for htc devices (this is where I get roms for my kaiser). But I've also seen roms for the x51 here too and I assumed someone may know something about em here. Anyway I have the "stock" wm5 rom flashed right now (flashed with sdloader) and it's pretty much in the same shape.
We don't frown upon answering questions for other devices. This forum is meant to help people. If you can get your answer here.. cheers on that.. hope you will.
mbannick said:
Yeah I know it's for htc devices (this is where I get roms for my kaiser). But I've also seen roms for the x51 here too and I assumed someone may know something about em here. Anyway I have the "stock" wm5 rom flashed right now (flashed with sdloader) and it's pretty much in the same shape.
Click to expand...
Click to collapse
sorry wasnt meaning to sound sarcastic, ive had some experience of axim but mostly wm5, just wasnt too clear on ur issues, what exactly happens? you say it freezes but what do you do that makes it so?
Well that's the thing it freezes randomly, even just sitting there it will freeze. I want to say its the flash but every time I check it the test comes out clear. So the the only thing I can think of is the bootloader is messed up.
Ive just been to the dell support site and wow, alot of un happy people, i can see why your friend didnt want it anymore...
After doing some reading there i can only suggest you download their official rom and rom updates and see if you can get it running normally. What i dont understand is flashing a new rom should clear everything, i dont think it is the bootloader if the system boots up fully correctly, it has to be a rom issue (or hardware of course).
check out these sites, doesnt make good reading im afraid :
http://search.euro.dell.com/results...~srd=False&ipsys=False&advsrch=False&~ck=anav
http://en.community.dell.com/forums/3530.aspx?PageIndex=2
good luck and let me know how you get on.
Well as I said it takes several tries to get into windows (sometimes it wont work at all until I leave it without the battery for an hour or so) so its not booting up normally at all . Anyway I had the wm5 a12 rom on there for a while but it still has the same problems (I used sd flash since I really cant sync and flash with the way it freezes). So yeah I'm not sure what I can do
mmm.....
If youve had several different roms on it, including official ones, it could mean a hardware problem too.......
Im no chef, but i would have expected a bootloader issue to be resolved with a known working official rom?
How old is the Dell? Just a thought, have you tried the online help with a technical rep from Dell, they were good when trying to sort out an issue with my 4 year old laptop? Sorry but im running out of ideas........
Hey I think I got it! Seems the previous owner modified the battery latch. After messing around a bit I stuck a toothpick on the "button" that is depressed when the door is closed and it seems to be running perfectly stable! I even did a few resets and each time it boots just fine. Thanks to everyone who replied and offered advice.
hoorah! saved by a tooth pick, now ive heard it all haha. congrats!