Hi!
I have this problem; when I have an incoming call and I press the button of bluetooth hands free the call is rejected instead of being accepted!
Do you know how I can change this? Perhaps with a registry hack?
i bet you have a plantronics headset, i also have the same problem, though only with plantronics and not with other manufactured headsets. seems to be compatibility issue with wm6?
Hi,
No, I have a Philips HHB-600.
I have found a partial workaround for this that partially solves the problem.
By default, sound is redirected to the device when you press the device button to accept the call and to headset if you press the headset button to accept the call.
Set (or add if completely missing) the ConnectScoInAlways=1
under HKEY_LOCAL_MACHINE\Software\Microsoft\Bluetooth\AudioGateway. This will cause the device to redirect voice always to the headset. Still accepting the call from the headset will not work but a least you will be able to use your headset to speak/listen and end to the call.
Related
I have bluetooth headset NOKIA BH-101. it works with my htc tornado like handsfree. but i can not get it play all sounds. it only works with calls but when ii play sounds or video files it sounds out of my phone.
This gadget supports Hands-Free and Headset but does not work with voice dial function. Can anybody help?
makler1981 said:
I have bluetooth headset NOKIA BH-101. it works with my htc tornado like handsfree. but i can not get it play all sounds. it only works with calls but when ii play sounds or video files it sounds out of my phone.
This gadget supports Hands-Free and Headset but does not work with voice dial function. Can anybody help?
Click to expand...
Click to collapse
try to chek the settings
bestever said:
try to chek the settings
Click to expand...
Click to collapse
what exact setting do you mean?
try this cab i found on http://mobile.surrealnetworks.com/
Check this thread too:
http://forum.xda-developers.com/showthread.php?t=263735&highlight=a2dp
This will install newest bt stack.
I should also ask which ROM you're using. The newer ROMs seem to be a lot better.
I'd also like anyone who could to tell me which BT stack is included on the newer ROMs, like Nitro or vjgrace.
Exitao said:
Check this thread too:
http://forum.xda-developers.com/showthread.php?t=263735&highlight=a2dp
This will install newest bt stack.
I should also ask which ROM you're using. The newer ROMs seem to be a lot better.
I'd also like anyone who could to tell me which BT stack is included on the newer ROMs, like Nitro or vjgrace.
Click to expand...
Click to collapse
my ROM is WM6 by vjgrace v3.4
Again I could describe my Nokia BH-101 BT headset with handsfree functionality on WM6 by vjgrace v3.5. It works nice as headset i can hera incoming calls, answer them, call last dialed number. But I CAN NOT make it start voice calling, due to device itself - it does sounds special tone that means that voice dial is started, but my phone does not recognise it. by the way useing celetask - there is special feature - that alows you to redirect all sound to headset and it work. As for me i don't need it (you are to have special BT Headset for listening to music. This headset generates rather bad sound(but not voice).
So again
I can do:
makle calls,
answer calls,
dial last dialed call.
swap and hold calls.
I can not do:
make voice dial
any voice commands
What are the problems:
Everytime I answer the call not by the headset but via the phone it looses the connection with headset, so i need to restart BT service (or headset).
It happens even if I answer by headset but during the call i need to speak via phone then i press right softkey and choose "turn handsfree off" and aain phone looses the headset
In this case I I make new call but in right soft key menu "turn handsfree on" is not active
If it's possible to make phone speak contact's name litterally during incoming call so i could know who is calling me.
IRC, voice dialling with WM phones is a bit of a problem. I seem to recall reading about this somewhere in the XDA-Dev forums.
On my headset, the function that calls for redial is the same for voice dial (wtf? I know.) It always redials.
As for the speaking of the contacts' names, it should be possible... if your phone can speak the contacts' recorded voice names w/o BT.
I'm sure you've heard of this issue before but I was unable to find a fix!
I have been using VC1.6 through strictly the device mic / speaker and it has worked great except for some reason it does not announce incoming calls.
Currently using ATT TILT with WM6
Using 520 Plantronics BT Headset
I downloaded "Bluetooth Voice Command Configuration" from XCSdM but it doesn't seem to do anything to help!
When I press the talk/end button on the Headset it enables the bluetooth static but it does not give the VC prompt.
I'd also like it to be able to announce incoming calls through the bluetooth!
Anyone?!
Well, I got the incoming calls to announce!!! Now all I need to do is find out how to get the VC1.6 and my bluetooth synced so that when I press my bluetooth headset button it activates the VC...
Please? LOL
Does your bluetooth headset support the handsfree profile? Not all headsets support the handsfree profile (even if you can use it to pick up and answer calls). I've got VC 1.6 and voice command working just fine with my Tilt and Jabra 8010.
edit: seems your plantronics does support the HFP. Did you ensure you "checked" the box for Hands Free Service when you paired it?
Yes, it's completely paired and the handsfree is checked :-\
I'm stumped. I get incoming call notifications, I get announcement reminders, etc.... but when I push the button on the headset it tries to initiate (or answer) a call.... If I hold it down, it powers off the headset. If I double click it, it calls the last person I talked to.
Maybe I just don't know how to function my headset to get it to prompt for VC?
I followed the "RandyRants" Tip to get everything working and it did activate the announcement of incoming calls, etc... just can't make commands yet.
I'm also using the BT VC Config enabled @ 30 duration.
I'm 1/2 way there!! Now I just need to cross the finish line...
Here's the link yo RandyRants that I followed: http://www.randyrants.com/2007/05/wm6_tip_voice_c.html
Any advice?
Hi all,
I have a problem with MS Voice Command 1.6.
It 'sorta' works right now ... when I press the button on my BT headset (Motorola H700) it initiates the voice command on the Treo. However, the 'beep' is played from the treo speaker, not the BT headset. When I spoke the voice command, I must also speak to the Treo mic, not the BT headset. This sucks when you are in a noisy environment.
When the call is connected, it does go through the BT headset so that's good. But it's just when you want to initiate a voice command, you have to speak to the mic on the phone. All the announcements also come through the phone's speaker only, not the BT headset.
Has anybody found a fix to this?
Thanks in advance
Try deleting the headset and reacquiring it via bluetooth. I had to do this a couple of times before this corrected
Hmmm I've done it quite a few times already ... but I can try it again.
Mine does this too. If there is no fix, I will have to go back to the at&t one.
Removing and re-adding BT headset doesn't work. After doing some more homework, it seems like the problem is Treo 750, among a # of other phones (like Hermes) uses a BT stack that is incompatible with MS's and that is the reason why.
Searching on the Hermes site there IS actually a workaround which fixes half the problem.
To make long story short, after trying to fix recommended by that site, now I can speak to the BT headset to issue voice command.
Meaning, when I press the BT headset button, I hear the VC chime from my headset, not from the phone's speaker. And when I issue voice command I also speak to the BT headset, not the phone's mic.
What it doesn't fix, is notification STILL comes through the phone's speaker and not the BT headset, even with all the correct settings under MVC.
But I'm ok with that ... I can live with this.
number16 said:
Removing and re-adding BT headset doesn't work. After doing some more homework, it seems like the problem is Treo 750, among a # of other phones (like Hermes) uses a BT stack that is incompatible with MS's and that is the reason why.
Searching on the Hermes site there IS actually a workaround which fixes half the problem.
To make long story short, after trying to fix recommended by that site, now I can speak to the BT headset to issue voice command.
Meaning, when I press the BT headset button, I hear the VC chime from my headset, not from the phone's speaker. And when I issue voice command I also speak to the BT headset, not the phone's mic.
What it doesn't fix, is notification STILL comes through the phone's speaker and not the BT headset, even with all the correct settings under MVC.
But I'm ok with that ... I can live with this.
Click to expand...
Click to collapse
you have a link to this fix???
Is there a way to hang up a phone call from the handsfree button? Its a bit annoying having to pick up the phone from the pocket everytime you want to hangup. There should be some way to hang up from the handsfree instead of "switching calls"
What handsfree are you referring to? The headset that came with the phone or a seperate BT handsfree? If it is seperate BT handsfree then the answer is that this should work but it depends upon your handsfree. I use two different BT handsfree units and both can hang up calls with a press of a button.
peterc10 said:
What handsfree are you referring to? The headset that came with the phone or a seperate BT handsfree? If it is seperate BT handsfree then the answer is that this should work but it depends upon your handsfree. I use two different BT handsfree units and both can hang up calls with a press of a button.
Click to expand...
Click to collapse
I have used the original handsfree and when i get a call I can answer it with the button on the mic, but when i want to hang up i have to pick up the phone and press hang up i cant use the handsfree button, if i press the handsfree button it wants to "switch calls" even thou there is only one call.
Ok I am going to ask this question because there are way to many bluetooth programs here and I need to find a specific one.
All I want is for when I turn my headset on and its connected to my phone I want it to transfer the sounds to the headset and pull the microphone from the headset. So when its connected it immediately sends the sound to the headset; Not just in call sounds. I mean all sounds. I am using VITO VOice command so I just need it to send the sound to the headset and pull the microphone form the headset. Also I need it to send teh sound back to the headset after a call as well if a call is happening while using the headset for sound.
Can this be done?
try this
http://forum.xda-developers.com/attachment.php?attachmentid=30959&d=1161286247
Thanks nir36, I've just tried BTaudio but, unfortunately, it doesn't seem to reconnect the audio gateway after a call ends.
----
What I use is a program called BtMusic (available here: http://maxmobilesoft.com/index.php/software/btmusic). It is shareware, I think, but does pop up a message box when opening the program and every 5 or so times the gateway is established. I believe you can donate to get rid of these prompts, but you'd have to ask the author through that website. It isn't annoying if you don't need to keep reconnecting very often. BtMusic seems to have some advantages:
1. Reconnects automatically after a call ends.
2. Does not need the headset to be turned on before being enabled - it waits for the headset to connect and connects the gateway when it is found (you can therefore leave BtMusic running in the background and just turn on and off the headset as needed!).
3. Supports stereo headsets.
All the best,
Martin
Anybody have any other ideas?